- No category
advertisement
CE-Parallel CE-SSI CE-ISI CE-NSW LA-Parallel LA-SSI LA-ISI LA-NSW
4.3.1.6 Output logic
Changing between the output logic, that means between high active or low active is possible for
encoders CE with parallel interface.
Select between:
-
-
0V == LOW
0V == HIGH high-active switching logic low-active switching logic
For certain applications an inverted output of the data can be necessary. This is called negative or positive logic. Whether the encoder outputs the data accordingly is defined with this selection.
Printed in the Federal Republic of Germany
07/06/2015 TR - E - BA - GB - 0012- 04
TR-Electronic GmbH 1996, All Rights Reserved
Page 27 of 69
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Contents
- 5 Revision index
- 6 1 Safety instructions
- 7 2 Wiring example for the programmable encoders
- 8 3 Switch on PT100N and encoder
- 9 4 Menu chart
- 10 4.1 Operation
- 12 4.2 Read Menu
- 13 4.3 Edit Menu
- 14 4.3.1 Edit Encoder
- 23 4.3.1.1 Display encoder type
- 23 4.3.1.2 Display output mode
- 24 4.3.1.3 Output mode
- 25 4.3.1.4 Transmit code
- 26 4.3.1.5 Transmit repetition
- 27 4.3.1.6 Output logic
- 28 4.3.1.7 Data bus active
- 29 4.3.1.8 Data valid
- 30 4.3.1.9 Negative values
- 31 4.3.1.10 Count direction
- 32 4.3.1.11 Offset
- 33 4.3.1.12 Preset function
- 34 4.3.1.13 Programmable gear
- 35 4.3.1.14 Revolutions / length
- 36 4.3.1.15 Steps / length
- 37 4.3.1.16 Initial point of measurement
- 38 4.3.1.17 Preset position
- 39 4.3.1.18 Start area
- 40 4.3.1.19 End area
- 41 4.3.1.20 Number of data bits
- 42 4.3.1.21 Special bits
- 43 4.3.1.22 Parallel outputs
- 44 4.3.1.23 Maximum ISI frequency
- 45 4.3.1.24 Correction value
- 46 4.3.2 Edit TA-MINI
- 47 4.3.2.1 Display type
- 47 4.3.2.2 Display position
- 47 4.3.2.3 Signs
- 48 4.3.2.4 Step number
- 48 4.3.2.5 Start of measurement
- 49 4.3.3 Edit cams
- 50 4.4 Save Menu
- 50 4.5 Verify data
- 51 4.6 Adjustment Menu
- 52 4.7 Main parameters
- 52 4.7.1 Encoder type
- 52 4.7.2 Maximum number of revolutions
- 53 4.7.3 Maximum number of steps / revolutions
- 53 4.7.4 Software version
- 53 4.7.5 Display transmission mode
- 54 4.8 Language Menu
- 55 4.9 Service Menu
- 55 4.9.1 Hex Dump ROM
- 55 4.9.2 Hex Dump RAM
- 56 4.9.3 Keyboard test
- 56 4.9.4 Display Test
- 57 4.10 EPROG DIALOG (Version 2.1a and above)
- 58 5 Appendix
- 58 5.1 Programming examples
- 61 5.2 Synchronous serial interface SSI
- 62 5.3 SSI output tree format
- 63 5.4 SSI transmit format left binding