advertisement
Master/Slave Mode
The master/slave-operation enables that several devices can be synchronized and controlled by one masterdevice.
On the rear panel of the LED Bar 2 RGBA 252/10 you can find an XLR-jack and an XLR-plug, which can be used for connecting several devices.
This device then works as master-device and controls the slave-devices, which are to be connected to the master-device via a stereo shielded cable. Connect the OUT-jack with the IN-plug of the next device.
Press the MODE button to select the SLAVE mode. The devices set in this manner can now be controlled by the master unit.
Please press the ENTER button to confirm and to exit the SLAVE Mode.
Sound Control Mode
Press the MODE button and choose Sound Controlled Mode (SOUND).
Press the ENTER button to select the desired sensitivity and frequency of the loops, respectively.
The desired sensitivity (Sensit 00-31) and frequency of the loops (Frequency = FQN 01-99) can be selected via the UP or DOWN buttons.
Please press the ENTER button again to confirm and to exit the SOUND Mode.
CLEANING AND MAINTENANCE
DANGER TO LIFE!
Disconnect from mains before starting maintenance operation!
We recommend a frequent cleaning of the device. Please use a soft lint-free and moistened cloth. Never use alcohol or solvents!
There are no servicable parts inside the device except for the fuse. Maintenance and service operations are only to be carried out by authorized dealers.
Replacing the fuse
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Open the fuseholder on the rear panel with a fitting screwdriver.
Step 2: Remove the old fuse from the fuseholder.
Step 3: Install the new fuse in the fuseholder.
Step 4: Replace the fuseholder in the housing.
Should you need any spare parts, please use genuine parts.
If the power supply cable of this device becomes damaged, it has to be replaced by a special power supply cable available at your dealer.
25/26 00050718.DOC, Version 1.1
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 EINFÜHRUNG
- 3 Lieferumfang
- 3 SICHERHEITSHINWEISE
- 5 BESTIMMUNGSGEMÄßE VERWENDUNG
- 6 GERÄTEBESCHREIBUNG
- 7 INSTALLATION
- 7 Überkopfmontage
- 8 Befestigung
- 9 DMX-512 Ansteuerung
- 9 Anschluss zwischen Geräten
- 9 Anschluss ans Netz
- 10 BEDIENUNG
- 10 Stand Alone-Mode
- 10 Chaser
- 10 Auswählen eines Chasers
- 11 Auto Mode
- 11 DMX Mode
- 11 Adressierung des Geräts
- 11 DMX Channel Auswahl : Auswählen eines DMX Kanal Modus bis zu 19 Kanal Belegung
- 13 Master/Slave-Betrieb
- 13 Musikgesteuert
- 13 REINIGUNG UND WARTUNG
- 13 Sicherungswechsel
- 14 TECHNISCHE DATEN
- 15 INTRODUCTION
- 15 Delivery includes
- 15 SAFETY INSTRUCTIONS
- 18 OPERATING DETERMINATIONS
- 18 DESCRIPTION OF THE DEVICE
- 18 INSTALLATION
- 18 Overhead rigging
- 20 Attachment
- 20 DMX-512 control
- 21 Connection between devices
- 21 Connection with the mains
- 21 OPERATION
- 22 Stand Alone-Mode
- 22 Chaser
- 22 Selecting a chaser
- 22 Auto Mode
- 22 DMX Mode
- 23 Addressing
- 23 DMX Channel Selection : Choosing a DMX Channel Mode up to 19 Channal Occupation
- 25 Master/Slave Mode
- 25 Sound Control Mode
- 25 CLEANING AND MAINTENANCE
- 25 Replacing the fuse
- 26 TECHNICAL SPECIFICATIONS