- No category
advertisement
OLS425 / OLP425 series - Electrical Mechanical Data Sheet
The modules are normally delivered without labels on each module when packaged on tapeand-reel or tray since the labels do not withstand soldering. However, if they are delivered with labels on each module, the labels should be removed before the module is processed since the labels do not withstand the heat of soldering.
The device recommended maximum re-flow temperature is 245°C for 10 sec.
The device absolute maximum re-flow temperature is 250°C for 3 sec.
8.3 Antenna Issues
The unit cannot be mounted arbitrary, because of the radio communication. The unit with an internal surface mounted antenna cannot be mounted in a metal enclosure. No metal casing or plastics using metal flakes should be used, avoid also metallic based paint or lacquer. Keep a minimum clearance of
5 mm between the antenna and the casing. Keep minimum 10 mm free space from metal around the antenna including under and above. If a metal enclosure is required, one of the external antenna options has to be used. See
Surface Mounted Antenna (Internal)
for more information on the antenna options available.
9 Bluetooth Information
9.1 General Information
In the tables below you can find information about Bluetooth properties.
Table 17: Bluetooth information cB-OLP425, cB-OLS425 and cB-OLS426.
Parameter Data
Bluetooth Low Energy radio
RF output power
(conducted - excluding antenna gain)
Receive sensitive level
Output frequency
Bluetooth standard
Texas Instrument CC2540F256
2 dBm + antenna gain (See Antennas )
-91 dBm - antenna gain (See
)
2.402 - 2.480 GHz, ISM band.
4.0 (single mode / Bluetooth Smart)
9.2 Bluetooth Qualification Information
All products based on the PCB cB-0950 (cB-OLP425, cB-OLS425 and cB-OLS426) have been qualified according to the Bluetooth specification 4.0 (single mode / Bluetooth Smart).
Table 18: Bluetooth Qualification information
UBX-15016241 - R14 Production Information
Page 42 of 52
advertisement
Related manuals
advertisement
Table of contents
- 5 Introduction
- 7 Related Documents
- 7 Serial Port Adapter Related Documents
- 8 Product Variants
- 8 cB-OLP425 Platform Variants
- 9 cB-OLS425 Serial Port Adapters Variants
- 10 cB-OLS426 Serial Port Adapters Variants
- 10 Block Diagram
- 11 cB-OLP425 Bluetooth Stack and Application Platform Software
- 12 Electrical Interface and Connectors
- 12 Electrical Interface and Connectors on the cB-OLP425 Platform
- 12 cB-OLP425 Connector Interfaces
- 14 cB-OLP425 Pin Numbering
- 14 cB-OLP425 Pin Description
- 17 Peripherals
- 17 Temperature Sensor
- 17 Accelerometer
- 18 LEDs
- 18 Electrical Interface and Connectors on the cB-OLS425 Serial Port Adapter
- 18 cB-OLS425 Connector Interfaces
- 19 cB-OLS425 Pin Numbering
- 19 cB-OLS425 Pin Description
- 20 Electrical Interface and Connectors on the cB-OLS426 Serial Port Adapter
- 20 cB-OLS426 Connector Interfaces
- 21 cB-OLS426 Pin Numbering
- 21 cB-OLS426 Pin Description
- 22 Characteristics
- 22 Power Supply cB-OLP425 and cB-OLS425
- 22 Power Supply cB-OLS426
- 23 Current Consumption for cB-OLP425
- 23 Current Consumption for cB-OLS425 and cB-OLS426
- 24 Input/Output Signals
- 25 Environmental
- 25 Hardware Reset
- 25 Calculating Energy Consumption
- 26 cB-OLS425/426 Serial Port Adapter Operating Status
- 27 Antennas
- 27 Surface Mounted Antennas (Internal)
- 28 External Antennas
- 28 Antenna Accessories
- 29 Recommended Antennas
- 32 Alternative Antennas
- 36 Mechanics
- 36 cB-OLP425 and cB-OLS425 Mechanics
- 36 Module Dimensions
- 37 Battery Holder and Mounting Wings Dimensions (optionals)
- 38 Using the J6 PCB Solder Pads
- 41 Host Board
- 38 cB-OLP425 and cB-OLS425 Mounting Process
- 39 cB-OLS426 Mechanics
- 39 Module Dimensions
- 39 cB-OLS426 Mounting Holes
- 40 Using the J2/J3 Board-to-Board Connectors
- 40 Single Row Connectors
- 40 Double Row Connectors
- 41 Using the J6 PCB Solder Pads
- 41 Host Board
- 41 cB-OLS426 Mounting Process
- 42 Antenna Issues
- 42 Bluetooth Information
- 42 General Information
- 42 Bluetooth Qualification Information
- 43 Regulatory Information
- 43 European Union regulatory compliance
- 43 Declaration of Conformity
- 44 Safety Compliance
- 44 FCC and IC Compliance
- 44 Compliance for cB-0950
- 44 FCC Statement for cB-0950
- 44 Antenna
- 44 Caution
- 45 IC Compliance
- 45 Labeling Requirements for End Product
- 46 UL Listing Information
- 46 Japan Radio Equipment Compliance (TELEC)
- 46 Compliance with RoHS Directive
- 46 Guidelines for Efficient and Safe Use
- 46 General
- 47 Product Care
- 47 Radio Frequency Exposure
- 47 Electronic Equipment
- 48 Potentially Explosive Atmospheres
- 48 Power Supply
- 49 Package Information
- 49 cB-OLP425 and cB-OLS425 Tape Dimensions
- 50 cB-OLS426 Tape Dimensions
- 50 Reel Dimensions