advertisement
D:\NORM'S JOB\SONY HA\SO130041\STR-DA1800ES_PMRF
03\4428194123_USFR\US03DES_STR-DA1800ES-CEL.fm
masterpage: Left
Description and location of parts
Front panel
1 2 3 4 5 6 7 8 9 qk qj qh qg qf
A ?/1 (on/standby) (page 42, 63, 69)
B ON/STANDBY indicator
Lights up as follows:
Green: The receiver is turned on.
Amber: The receiver is in standby mode, and
– Either Control for HDMI, Network Standby, or
Bluetooth Standby is set to on.
– The receiver in zone 2 is turned on.
Lights off when the receiver is in standby mode and Control for HDMI, Network Standby,
Bluetooth Standby, and zone 2 are set to off.
Note
If the ON/STANDBY indicator flashes slowly,
the software update is in progress (page 81). If
the indicator flashes in quick succession, the
software update has error (page 120).
C INPUT SELECTOR (page 55, 61, 91)
E Remote control sensor
Receives signals from remote control.
H DIMMER
Adjusts the brightness of the display panel in 3 levels.
10
US
qd qs qa q;
K iPod/iPhone (
(USB) port and
M 2CH/A.DIRECT, A.F.D., MOVIE/
HD-D.C.S., MUSIC (page 65, 67)
N TONE, TONE MODE
Press TONE MODE repeatedly to select BASS or TREBLE, then turn TONE to adjust the level.
Operates the PARTY STREAMING function.
Hold down the button to start or close a PARTY.
Operates the Bluetooth function.
R PHONES jack
Connects to headphones.
STR-DA1800ES
4-428-194-12(3)
D:\NORM'S JOB\SONY HA\SO130041\STR-DA1800ES_PMRF
03\4428194123_USFR\US03DES_STR-DA1800ES-CEL.fm
masterpage: Right
Indicators on the display panel
1 2 3 4 5 6 5 7 8 9 0 qa qs
LH SW RH
L
SL
C
S
R
SR
SB L SB SB R
ZONE 2
PL II x z
USB HDMI COAX OPT PARTY
D.L.L.
D.C.A.C.
EQ
ARC D + EX True HD
S.OPT. MEM DTS HD MSTR HI RES LBR
LFE UPDATE D.RANGE
A.P.M.
ST 96 24 LPCM SP A B
BLUETOOTH
BI
-
AMP SLEEP
wj
A SW
Lights up when the audio signal is output from the SUBWOOFER jack.
B ZONE 2
Lights up while operation in zone 2 is being enabled.
C D.L.L.
Lights up when the D.L.L. (Digital Legato
Linear) function is activated (page 102).
D USB
Lights up when iPod/iPhone or USB device is detected.
E Input indicator
Lights up to indicate the current input.
HDMI
Digital signal is input through the HDMI jack.
COAX
Digital signal is input through the COAXIAL
OPT
Digital signal is input through the OPTICAL
ARC
TV input is selected and the Audio Return
Channel (ARC) signals are detected.
F PARTY
Lights up when PARTY STREAMING function
G Dolby Digital Surround indicator*
Lights up the respective indicator when the receiver is decoding the corresponding Dolby
Digital format signals.
D
D EX
D+
TrueHD
Dolby Digital
Dolby Digital Surround EX
Dolby Digital Plus
Dolby TrueHD wh wg wf wd ws wa w; ql qk qj qh qg qf qd
H NEO:6
Lights up when DTS Neo:6 Cinema/Music
decoder is activated (page 66, 67).
I DTS-HD indicator*
Lights up the respective indicator when the receiver is decoding the corresponding DTS-HD format signals.
DTS-HD MSTR
DTS-HD HI RES
DTS-HD LBR
DTS-HD Master Audio
DTS-HD High Resolution
Audio
DTS-HD Low Bit Rate
Audio
J BLUETOOTH
Lights up when Bluetooth device is connected.
L Wireless LAN signal strength indicator
Lights up to show the strength of the wireless
No signal.
The signal strength is weak.
The signal strength is moderate.
The signal strength is strong.
M SLEEP
Lights up when the Sleep Timer is activated
N BI-AMP
Lights up when surround back speakers
selection is set to “BI-AMP” (page 94).
P LPCM
Lights up when the receiver is decoding the
Linear PCM signals.
continued
11
US
STR-DA1800ES
4-428-194-12(3)
D:\NORM'S JOB\SONY HA\SO130041\STR-DA1800ES_PMRF
03\4428194123_USFR\US03DES_STR-DA1800ES-CEL.fm
masterpage: Left
Q DTS(-ES) indicator*
Lights up the respective indicator when the receiver is decoding the corresponding DTS format signals.
DTS
DTS-ES
DTS 96/24
DTS
DTS-ES
DTS 96 kHz/24 bit
R Tuning indicator
Lights up when the receiver tunes to a radio station.
MEM
Memory function, such as Preset Memory
(page 64), etc., is activated.
ST
Stereo broadcast
S S.OPT.
Lights up when Sound Optimizer function is
T A.P.M.
Lights up when the A.P.M. (Automatic Phase
Matching) function is activated.
You can only set the A.P.M. function in the
DCAC (Digital Cinema Auto Calibration)
U EQ
Lights up when the equalizer is activated.
V D.RANGE
Lights up when dynamic range compression is
W D.C.A.C.
Lights up when the measurement results of the
“Auto Calibration” function are applied.
X UPDATE
Lights up when a new software is available
Y Dolby Pro Logic indicator
Lights up the respective indicator when the receiver performs Dolby Pro Logic processing.
This matrix surround decoding technology can enhance input signals.
PL
PL II
PL IIx
PL IIz
Dolby Pro Logic
Dolby Pro Logic II
Dolby Pro Logic IIx
Dolby Pro Logic IIz
Note
These indicators may not light up depending on the speaker pattern setting.
Z
Lights up when the disc being played back contains an LFE (Low Frequency Effect) channel and the LFE channel signal is actually being reproduced.
wj Playback channel indicator
The letters (L, C, R, etc.) indicate the channels being played back. Based on the speaker settings, the box around the letter(s) vary to show how the receiver downmixes the source sound.
LH
RH
L
R
C
SL
SR
S
SBL
SBR
SB
Front Left High
Front Right High
Front Left
Front Right
Center (monaural)
Surround Left
Surround Right
Surround (monaural or the surround equipment obtained by Pro Logic processing)
Surround Back Left
Surround Back Right
Surround Back (the surround back equipment obtained by 6.1 channel decoding)
Example:
Speaker pattern: 3/0.1
Recording format: 3/2.1
Sound Field: A.F.D. AUTO
* When playing a Dolby Digital or DTS format disc, make sure that you have completed the digital connections and that INPUT MODE is not set to
“ANALOG” (page 92) or “A. DIRECT” is not
selected.
12
US
STR-DA1800ES
4-428-194-12(3)
D:\NORM'S JOB\SONY HA\SO130041\STR-DA1800ES_PMRF
03\4428194123_USFR\US03DES_STR-DA1800ES-CEL.fm
Rear panel
1 2 3 4
masterpage: Right
9 8 6 7 6
A DIGITAL INPUT/OUTPUT section
OPTICAL IN jacks (page 26, 30,
B Controls jacks for Sony equipment
and other external equipment
IR REMOTE IN/OUT jacks
Connect to interlock on/off of the power supply of other 12V
TRIGGER compliant equipment, or the amplifier.
5
C COMPONENT VIDEO INPUT/
OUTPUT section
Green
(Y)
Blue
(P
B
)
Red
(P
R
)
Y, P
B
, P
R
IN/OUT* jacks
Green
(Y)
Blue
(P
B
)
Red
(P
R
)
Y, P
B
, P
R
OUT* jacks
D NETWORK section
Wireless LAN antenna
continued
13
US
STR-DA1800ES
4-428-194-12(3)
D:\NORM'S JOB\SONY HA\SO130041\STR-DA1800ES_PMRF
03\4428194123_USFR\US03DES_STR-DA1800ES-CEL.fm
masterpage: Left
F AUDIO INPUT/OUTPUT section
White (L)
Red (R)
Black
Remote control
Use the supplied remote control to operate this receiver and other equipment. The remote control is pre-programmed to operate Sony audio/video equipment. You can also program the remote control to operate non-Sony
equipment. For details, see “Programming the remote control” (page 113).
RM-AAP080
wg wf wd ws
1
2
3
G VIDEO/AUDIO INPUT/OUTPUT
Yellow
VIDEO IN/OUT* jacks
White (L)
AUDIO IN/OUT jacks
Red (R)
4
wa w; ql qk qj
5
6
7
8
9
H RS232C port
Used for maintenance and service.
I TUNER section
AM ANTENNA terminals
* You must connect the HDMI OUT or MONITOR
OUT jack to your TV to watch the selected input
qh qg qf qd
0 qa qs
14
US
STR-DA1800ES
4-428-194-12(3)
D:\NORM'S JOB\SONY HA\SO130041\STR-DA1800ES_PMRF
03\4428194123_USFR\US03DES_STR-DA1800ES-CEL.fm
masterpage: Right
A ?/1 (on/standby)
Turns the receiver on or sets it to the standby mode.
If you press ZONE (C) to switch the remote to zone 2 mode, you can turn the power for zone 2 on or off using ?/1.
Saving the power in standby mode
When Control for HDMI (page 103), Network
Standby (page 106), and Bluetooth Standby
(page 107) are set to off, and the receiver in
zone 2 is turned off.
B AV ?/1
1)
(on/standby)
Turns on or off the audio/video equipment that the remote control is programmed to operate.
To turn the TV on or off, press TV (W) and then press AV ?/1.
If you press ?/1 (A) at the same time, it will turn off the receiver and all other equipment including an amplifier in zone 2 (SYSTEM
STANDBY).
Note
The function of the AV ?/1 changes automatically each time you press the input buttons (D).
D Input buttons
2)
Selects the equipment you want to use. When you press any of the input buttons, the receiver turns on. The buttons are assigned to control
Sony equipment. You can program the remote control to control non-Sony equipment
following the steps in “Programming the remote control” on page 113.
Numeric/text buttons
1)2)
Press SHIFT (V), then press numeric/text buttons to
– preset/tune to the preset stations (page 64).
– select track numbers. Press 0/10 to select track number 10.
– select channel numbers.
– select the letters (ABC, DEF, etc.), punctuation marks (!, ?, etc.) or other symbols
(#, %, etc.) when you enter characters for network features.
Press TV (W), then press the numeric buttons to select the TV channels.
-/--
1)
Press SHIFT (V), then press -/-- to select the channel entry mode, either one or two digit.
Press TV (W), then press -/-- to select the TV channel entry mode.
>10
1)
Press SHIFT (V), then press >10 to select track numbers over 10.
ENT/MEM
1)
Press SHIFT (V), then press ENT/MEM to
– enter the value after selecting a channel, disc, or track using numeric buttons.
– store a station during tuner operation.
CLEAR
1)
Press SHIFT (V), then press CLEAR to
– erase a letter for network features.
– clear a mistake when you press the incorrect numeric/text button.
CHARACTER
Press SHIFT (V), then press CHARACTER to select the character type for network features.
Each time you press CHARACTER, the character type changes in sequence as follows:
“abc” (lowercase letters) t “ABC” (uppercase letters) t “123” (numbers)
ALPHABET SEARCH
Press SHIFT (V), then press ALPHABET
SEARCH to search for an item using a keyword
E SOUND FIELD +/–
Selects a sound field (page 65).
F Color buttons
1)
Works according to the guide on the TV screen.
G GUI MODE
Displays the GUI menu on the TV screen.
H TOOLS/OPTIONS
1)
Displays and selects items from the option menus.
Press TV (W), then press TOOLS/OPTIONS to display the TV function options.
I MENU, HOME
1)
Displays the menu to operate the audio/video equipment.
Press TV (W), then press HOME to display the menus of Sony TV.
J ./>
1)
,
m/M
1)
, N
1)2)
, X
1)
, x
1)
Skip, backward/forward, play, pause, stop operation.
<
/
<
1)
Press to
– replay the previous scene or fast forward the current scene.
– skip to previous or next album when using iPod/iPhone.
REPEAT
1)
Press SHIFT (V), then press REPEAT to play a track or a folder repeatedly.
SHUFFLE
1)
Press SHIFT (V), then press SHUFFLE to play a track or a folder in random order.
continued
15
US
STR-DA1800ES
4-428-194-12(3)
D:\NORM'S JOB\SONY HA\SO130041\STR-DA1800ES_PMRF
03\4428194123_USFR\US03DES_STR-DA1800ES-CEL.fm
masterpage: Left
FOLDER +/–
1)
Selects a folder.
TUNING +/–
1)
Scans a station.
PARTY
2)
Press SHIFT (V), then press PARTY to operate the PARTY STREAMING function.
Hold down the button to start or close a PARTY
D.TUNING
Enters direct tuning mode.
K TV CH +/–
1)2)
Press TV (W), then press TV CH +/– to scan for the preset TV channels.
PRESET +/–
1)2)
Selects preset stations or channels.
L F1/F2
1)
Press BD or DVD (D), then press F1 or F2 to select the equipment.
• DVD/HDD COMBO
F1: HDD
F2: DVD disc, Blu-ray Disc
• DVD/VCR COMBO
F1: DVD disc, Blu-ray Disc
F2: VCR
PREVIEW (HDMI)
This is a “Preview for HDMI” button.
Turns on a live picture-in-picture preview of
HDMI inputs connected to this receiver.
Preview windows display only HDMI IN 1,
IN 2, IN 3, IN 4 inputs.
Press V/v to select each HDMI input preview, then press to enter/confirm the selection.
(This feature is powered by Silicon Image
InstaPrevue™ technology)
Notes
• When watching HDMI IN, this function will be available.
• Preview window display only for HDMI IN 1,
IN 2, IN 3, IN 4 input.
Tips
• This function does not work in the following cases.
– HDMI device is not connected.
– Some unsupported HDMI video format is inputted.
– Current input is not HDMI input.
– When GUI is On.
– Zone2 / OutB setting is Zone2.
– Fast View setting is Off.
• Depending on the playback video format, this function may not work.
GUIDE
1)
Press TV (W), then press GUIDE to display the on-screen program guide.
SLEEP
Press AMP (X), then press SLEEP to set the receiver to turn off automatically at specified time.
Each time you press SLEEP, the display changes cyclically as follows:
0:30:00 t 1:00:00 t 1:30:00 t 2:00:00 t OFF
Tips
• To check the remaining time before the receiver turns off, press SLEEP. The remaining time appears on the display panel.
• The Sleep Timer will be canceled when you perform the following.
– Press SLEEP again.
– Update the software of the receiver.
M TOP MENU
1)
Opens or closes the BD-ROM’s or DVD’s Top
Menu.
POP UP/MENU
1)
Opens or closes the BD-ROM’s Pop-up Menu, or the DVD’s menu.
TV INPUT
1)
Press TV (W), then press TV INPUT or to select the input signal (TV input or video input).
WIDE
1)
Press TV (W), then press WIDE repeatedly to select the wide picture mode.
N MUTING
1)
Turns off the sound temporarily. Press the button again to restore the sound.
Press TV (W), then press MUTING to activate the TV’s muting function.
O TV VOL +/–
1)
Press TV (W), then press TV VOL +/– to adjust the TV volume level.
MASTER VOL +/–
1)
Adjusts the volume level of all speakers at the same time.
P DISC SKIP/iPhone CTRL
1)
Press to
– skip disc when using a multi-disc changer.
– enter iPod/iPhone control mode when using iPod/iPhone.
16
US
STR-DA1800ES
4-428-194-12(3)
D:\NORM'S JOB\SONY HA\SO130041\STR-DA1800ES_PMRF
03\4428194123_USFR\US03DES_STR-DA1800ES-CEL.fm
Q RETURN/EXIT O
1)
Returns to the previous menu or exits the menu while the menu or on-screen guide is displayed on the TV screen.
Press TV (W), then press RETURN/EXIT O to return to the previous menu of Sony TV.
R
1)
,
V/v/B/b
1)
Press V/v/B/b to select the menu items, then press to enter/confirm the selection.
S DISPLAY
1)
Views information on the display panel.
Press TV (W), then press DISPLAY to display information of TV.
T AUTO CAL
Press SHIFT (V), then press AUTO CAL to perform Auto Calibration.
Note
This button is not available when the receiver is in “GUI MODE”.
U SOUND OPTIMIZER
Activates the Sound Optimizer function
V SHIFT
Changes the remote control button function to activate the buttons printed in pink.
W TV
Changes the remote control button function to activate the buttons printed in yellow.
X AMP
Activates the receiver operation for main zone
Y RM SET UP
Programs the remote control (page 113).
1)
See the table on page 18 for information on the
buttons that you can use to control each equipment.
2)
The 5/JKL/VIDEO 1, N/PARTY and TV CH +/
PRESET + buttons have tactile dots. Use the tactile dots as reference when operating the receiver.
Notes
• The above explanation is intended to serve as examples.
• Depending on the model of your connected equipment, some functions explained in this section may not work with the supplied remote control.
masterpage: Right
continued
17
US
STR-DA1800ES
4-428-194-12(3)
D:\NORM'S JOB\SONY HA\SO130041\STR-DA1800ES_PMRF
03\4428194123_USFR\US03DES_STR-DA1800ES-CEL.fm
masterpage: Left
To control other Sony equipment
Name TV
B
AV ?/1
D
Numeric buttons
-/--, >10
ENT/MEM
z z z z z z z
CLEAR
F
Color buttons
z
H
TOOLS/
OPTIONS
<
/
<
,
FOLDER +/–
z
I
MENU, HOME
z z
J
./> z z z
REPEAT
SHUFFLE
m/TUNING –,
M/TUNING + z z z N, X, x
K
PRESET +/–,
TV CH +/–
L
F1/F2
GUIDE
M
TOP MENU,
POP UP/MENU
z z z
TV INPUT,
WIDE
(Wide mode)
N
MUTING
O
MASTER
VOL +/–,
TV VOL +/–
P
DISC SKIP/ iPhone CTRL
Q
RETURN/
EXIT O
R
V/v/B/b,
S
DISPLAY
a) b)
DVD player only.
LD player only.
c)
Video CD player only.
d)
Deck B only.
e)
CD player only.
z z z z z z
VCR DVD player,
DVD/VCR
Blu-ray
Disc player combo
HDD
Recorder
z z z z z z z z z z z a) z a) z z z z z a) z a) z z z z z a) z z a) z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z
PSX Video CD player,
LD player
z z
Digital CATV terminal
z
DSS Tape deck
A/B
z
DAT deck
CD player,
MD deck
z z z z z z z z z z z z z z z z z z z z z z b) z c) z z c) z c) z c) z z z b) z c) z z z z z z z z z z z z z z z z z z z z z z z z z z z d) z d) z z z d) z z z z z z z z z z z z e) z z e) z z z
18
US
STR-DA1800ES
4-428-194-12(3)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project