advertisement
Operation
As soon as the fuel has been ignited and the exhaust temperature has exceeded 100°C, an arrow appears indicating that the ignition door and the insulation door should be closed.
Fig. 10-2: Close ignition and insulation doors
When the insulation door is closed, the boiler switches to [Ignition] and later to [Heating] mode. Split logs and fire are depicted in the boiler.
As soon as the boiler is supplying heat to the buffer, the buffer pipes are completely displayed as is the boiler pump.
Fig. 10-3: Log boiler in heating mode
If the fuel in the boiler has been burned and the exhaust temperature is below 80°C, the boiler begins the ember burnout and afterwards switches to [Ready] mode.
If the [ASH] button was not pressed during heating, some charcoal and embers will remain in the boiler by design so that new fuel can be ignited more easily when it is added later.
If the button was pressed during heating, the boiler will perform a complete ember burnout.
[Boiler] function block – log boiler
10.2.2
Operating modes
Heating
The boiler is in heating mode and is channelling heat to the consumers.
Ember burnout
The fuel in the boiler is almost completely burned and the exhaust temperature is below 80°C.
Ready
The boiler is switched off and can be started up at any time.
Malfunction
A malfunction has occurred, preventing the boiler from heating. The cause can be found in the list of error messages.
Calibrating lambda probe
The lambda probe is undergoing automatic calibration.
It is not possible for the unit to heat whilst in this mode.
Insulation door open
The boiler's insulation door is open. If the boiler was previously in [Heating] mode, it will switch back to this mode after the insulation door is closed.
If the boiler was previously in a mode other than
[Heating], it will switch to [Ignition] mode after the insulation door is closed.
Ignition
The boiler's insulation door was opened earlier to add fuel or to start up the boiler. After the insulation door is closed, the boiler switches to this mode.
If the boiler is not being started up immediately, it can be switched off again by pressing the button. Then the button shines red.
Overtemperature
The boiler temperature has exceeded the maximum temperature [Boiler max]. The draught fan is switched off and a message appears on the screen indicating that less fuel needs to be added in future. Only when the boiler has cooled below 86°C will the draught fan switch on again and heating resume.
TWIN operation
Optional: only with additional TWIN burner
29
[Boiler] function block – log boiler
This mode appears when the buffer needs heat but the log boiler cannot provide it. Then the control system starts the TWIN burner to supply heat to the buffer. The current status of the TWIN burner is shown in the
[Twin] FUB.
Operation
30 www.eta.co.at
Operation [Boiler] function block – log boiler
31
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 General information
- 6 Preface
- 8 Warranty, guarantee and liability
- 10 Boiler functionality
- 12 Emission measurement
- 13 Safety
- 13 General information
- 13 Safety devices
- 15 Suitable fuels
- 16 Correct quantity of wood
- 17 Start-up
- 24 10 Operation
- 24 10.1 User interface
- 24 10.1.1 Overview
- 24 10.1.2 Setting the date and time
- 25 10.1.3 Changing the names of function blocks
- 26 10.1.4 Text menu navigation
- 27 10.1.5 Messages
- 28 10.2 [Boiler] function block – log boiler
- 28 10.2.1 Overview
- 29 10.2.2 Operating modes
- 32 10.3 [Buffer] function block - log boiler
- 32 10.3.1 Overview
- 34 10.3.2 Operating modes
- 35 10.3.3 Operation
- 36 10.3.4 Text menu
- 40 10.4 [Heating circuit] function block
- 40 10.4.1 Overview
- 42 10.4.2 Operating modes
- 43 10.4.3 The heating curve
- 45 10.4.4 Operation
- 47 10.4.5 Text menu
- 50 10.5 [Hot water tank] function block
- 50 10.5.1 Overview
- 51 10.5.2 Operating modes
- 52 10.5.3 Operation
- 54 10.5.4 Text menu
- 56 10.6 [Fresh water module] 2 pumps function block
- 56 10.6.1 Overview
- 57 10.6.2 Operating modes
- 57 10.6.3 Operation
- 59 10.6.4 Text menu
- 62 10.7 [Solar] function block
- 62 10.7.1 Overview
- 67 10.7.2 Operating modes
- 67 10.7.3 Text menu
- 70 10.8 [Aux.boiler] function block - with buffer
- 70 10.8.1 Overview
- 71 10.8.2 Operating modes
- 72 10.8.3 Operation
- 73 10.8.4 Text menu
- 74 Heating value