advertisement
Chapter 1: Description
Power System
Power System
The library supports single and redundant power configurations. The single configuration has a single AC line input and single DC power supply. The redundant configuration has dual AC line input and dual DC power supplies. You can hot swap a power supply if you have a redundant power supply. You can hot add a second power supply.
The power system consists of the following:
• Power supply
• Power distribution unit
• AC power cord
A single power switch, located on the front door of the control module, turns on and off all power for the control module and attached expansion modules. Each power distribution unit has a second circuit breaker, located in the rear of the module, that controls the module power supply output. The power supply has three LEDs that provide status information. The power system also has four fuses for system protection.
The control module and all expansion modules or right parking modules that contain drives must contain a power system. If an expansion module or right parking module contains only cartridges, its power is derived from the control module and a power system is not needed.
High-density expansion modules have their own AC power systems that can supply power to up to six (6) additional HDEMs if redundant power is installed. The additional HDEMs must be in consecutive positions to receive power from a single HDEM. Each power distribution unit has a circuit breaker located at the rear of the module.
38 Quantum Scalar i6000 User’s Guide
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Contents
- 13 Preface
- 19 Description
- 23 Front View
- 24 Hardware Configuration Options
- 25 Dual Robotics Configurations and Parking Modules
- 28 Control Module
- 31 Expansion Modules
- 36 Library Management Module
- 39 I/O Management Unit
- 43 Robot
- 43 Import/Export Stations
- 46 Cartridges
- 47 Cartridge Magazines
- 51 Tape Drives and Media
- 53 Mixed Media Support and Rules
- 54 Support for WORM
- 55 Operator Panel
- 56 Power System
- 57 Library Features
- 61 Troubleshooting Your Library
- 61 How Does the Library Report Issues?
- 66 Working With Tickets
- 110 Interpreting LEDs
- 133 Working With Command History Logs
- 139 Accessing Online Help
- 141 Configuring Your Library
- 142 Running the Setup Wizard
- 143 Enabling Licenses
- 146 Working With Partitions
- 174 Configuring Control Paths
- 180 Setting Up the Network Configuration
- 191 Managing Connectivity
- 198 Setting Up Policies for the Physical Library
- 203 Specifying the Date and Time
- 205 Configuring E-mail
- 208 Setting Up E-mail Notifications
- 214 Setting Up Media Security Notifications
- 216 Configuring Devices
- 217 Configuring Drive SCSI ID
- 220 Configuring Fibre Channel Drive Speed, Topology, and Loop ID
- 222 Configuring Fibre Channel I/O Blades
- 243 Generating the Library Configuration Report
- 245 Configuring Drive Cleaning
- 251 Registering SNMP Traps
- 253 Configuring Library Security
- 259 Using LDAP
- 266 Configuring Screen Saver Preferences
- 268 Working With Data Path Conditioning
- 270 About the Configuration Record
- 271 Setting Aisle Lights
- 272 Configuring a Webcam For Your Library
- 273 Working with Towers
- 277 Active Vault
- 278 About Active Vault
- 278 Configure Active Vault
- 285 Advanced Reporting
- 286 Media Usage Report
- 288 Viewing Cross-Partition Media Moves
- 291 Automated Media Pool
- 293 Requirements for Automated Media Pool
- 293 Configure Automated Media Pool
- 296 Use an Automated Media Pool
- 303 Capacity on Demand
- 305 Encryption Key Management
- 305 Encryption Key Management Systems
- 307 KMIP-compliant Encryption Key Management
- 307 FIPS-Certified Encryption Solution
- 311 Setting up EKM on the Scalar i6000
- 329 Using EKM Path Diagnostics
- 331 Monitoring EKM Server Status
- 333 Using Q-EKM
- 334 Using SKM
- 345 Extended Data Lifecycle Management
- 346 About EDLM
- 348 Configuring EDLM
- 360 Running Manual EDLM Tests
- 366 Viewing EDLM Test Sessions and Report Details
- 374 Diagnosing a Suspect EDLM Drive
- 375 Path Failover
- 376 Use the Storage Networking Wizard
- 377 License Drives for Path Failover
- 379 Configure Control Path
- 394 Configuring Data Path Failover
- 401 Configuring Host Access to Storage Networking Drives and Partitions
- 437 Configuring Access to StorNext
- 445 Partition Utilization Reporting
- 451 Running Your Library
- 452 Logging On and Off
- 456 Connecting to Multiple Libraries
- 457 Operator Panel
- 460 Library Management Console (LMC)
- 477 Understanding Location Coordinates
- 491 Viewing the Library (Physical or Partition)
- 493 Changing the Library’s State
- 495 Working With Local User Accounts
- 503 Shutting Down/Rebooting the Library
- 505 Powering Off the Library
- 505 Powering On the Library
- 506 Locking/Unlocking the I/E Station
- 508 When Robotics Are Not Ready
- 510 Using the Library Access Feature
- 515 Using the Command Line Interface
- 516 Logging on to the CLI
- 517 Command Line Interface (CLI) Commands
- 533 Maintaining Your Library
- 534 Monitoring the Library
- 570 Maintenance Actions
- 696 Using Sift Sort
- 700 Retrieving MIBs
- 701 Maintaining Air Filters
- 705 Robot, Tower and Power Rail Health Checks
- 707 Working With Cartridges and Barcodes
- 708 Handling Cartridges Properly
- 709 Write-Protecting Cartridges
- 710 Supported Barcode Formats
- 711 Barcode Label Requirements
- 711 Installing Barcode Labels
- 714 Using Cleaning Cartridges
- 715 Managing and Moving Media
- 727 Frequently Asked Questions
- 731 Network Port Settings
- 733 Glossary