Goodwe ESA Series
Manuals and User Guides for Goodwe ESA Series. We found 5 manuals for free downloads User manual
Below you will find brief information for GW5048-ESA. This smart hybrid inverter enables solar array and battery bank connection with utility grid. It directs energy, maximises solar energy use, minimises utility consumption, and provides backup power in case of outages. It has utility grid energy metering, a backup inverter for loads, a charger, dual MPPT, battery charge control, and system monitoring.
Key Features
High efficiency grid-tie utility interactive inverter
Utility grid energy metering system
Backup inverter for AC loads
Dual Maximum Power Point Tracking (MPPT)
Battery charge control
Solar array ground fault protection
Performance monitoring with WiFi
Pages: 42 Goodwe ESA Series User manual
Brand: Goodwe Category: Water heaters & boilers Size: 1 MB
Languages: English
Table of contents
Open manualOther manuals and documents
Frequently Answers and Questions
What type of batteries is the GW5048-ESA compatible with?
The GW5048-ESA is designed to work with lithium-ion batteries only.
What is the maximum continuous AC power that the inverter can provide for AC loads?
The GoodWe Smart Hybrid Inverter can provide up to 5000 Watts of continuous AC power for AC loads.
What should I do if the equipment appears to be damaged in any way?
Do not attempt to install this equipment if it appears to be damaged in any way. See the Warranty section for instructions on returning the equipment.
Questions & Answers
M M T
Why might the inverter be using grid power instead of the battery?
The inverter might be using grid power instead of the battery due to several reasons, including: System Working Mode Settings (Self-use Mode, BACK-UP Mode, TOU/Economic Mode where the system may intentionally charge from the grid during 'Valley' periods); Backup Power SOC Maintenance to ensure readiness for off-grid events; Immediate Charging function if enabled in advanced settings; Environmental and Safety Limits where the Battery Management System (BMS) might limit charging/discharging (e.g., due to low temperatures); and Peak Shaving mode, where the system buys power from the grid if the battery SOC is below a reserved limit during set times.
W W C
What do the blue-purple light indicators on the inverter signify?
A steady light indicates the inverter is in standby or normal operation (grid-tied or off-grid). A breathing light (fading in and out) indicates the system is starting or performing a self-test.
K K J
Where is the DC isolator switch located on the inverter?
The DC Switch (DC isolator) is located on the inverter unit and is identified as component number 6 in the product overview. It is used to control the connection or disconnection of the DC input.
B B I
How to control a heat pump or hot water system using excess solar production?
The inverter's dry contact port can manage additional loads such as heat pumps. This can be configured via time control, manual switch control, or an SG Ready heat pump connection.
B B I
How to control a heat pump or domestic loads based on excess solar production?
The inverter can control loads via a dry contact port. This can be configured using specific time periods, manual switch control (ON/OFF), or via an SG Ready heat pump connection to manage operation based on solar output.
S S Z
How to configure a master/slave wiring schematic for parallel inverter systems?
Use a CAT 5E or higher communication cable for connections. The inverter connected to the smart meter acts as the master; connect DRED, RCR, and protection equipment to this unit. Set the DIP switches of the first and last inverters to ON and all intermediate units to OFF. Finally, define each unit as Master or Slave via the SolarGo App, setting slave addresses before performing parallel networking on the master.
Y Y O
Does the ESA integrated inverter support EV charging connections?
Yes, the inverter is compatible with GoodWe AC charging stations. It features a dedicated EMS communication port (Port H) for connecting to a GoodWe charging pile or an external Energy Management System.
H H T
What is the function of load control?
The load control function is managed through the inverter's communication port (specifically the port labeled LOAD). It supports connection to dry contact signals to manage external loads. The DO (Digital Output) contact capacity is 24V DC @ 1A, using NO/COM (normally open) contacts. It specifically supports SG Ready heat pump access, allowing the system to control the heat pump via dry contact signals. It is also part of the communication interface that can also handle CT, RS485, and other signal cables for intelligent energy management.
F F X
What do the different colored indicator lights on the Smart Dongle signify?
The Smart Dongle primarily uses green and yellow indicator lights. A blue LED is not mentioned for the dongle itself; a blue-purple light is used for the inverter.
- Power Indicator (Green): A steady green light indicates the Smart Communication Stick is powered on. No light means it is off.
- Communication Indicator: A steady light signifies normal communication in WiFi or LAN mode. Different blinking patterns indicate specific statuses: single blink for Bluetooth signal enabled (waiting for app connection), two blinks for no router connection, four blinks for router connection without server connection, and six blinks for device identification. No light means a software reset or no power.
- LAN Port Communication Indicators (Green and Yellow): A steady green light means a normal 100Mbps wired network connection. A steady yellow light indicates a normal 10Mbps wired network connection, or a 10/100Mbps connection with no data transmission. A flashing yellow light means data is being transmitted or received. No light indicates the network cable is not connected.
advertisement