Regin VCV203DWM-2
Manuals and User Guides for Regin VCV203DWM-2. We found 3 manuals for free downloads Manual, Instructions
**Regin VCV203DWM-2** is a versatile room controller for heating and ventilation applications that enables you to create a comfortable indoor climate. The controller is equipped with two analog inputs for sensors or other signals, two digital inputs for external control and two relay outputs for controlling fans or dampers. The control functions are easily set up via the LCD display and the user-friendly menu structure. With its compact size and DIN rail mounting, the controller is easy to install in electrical cabinets or other confined spaces.
Key Features
Control heating and ventilation for a comfortable indoor climate
Two analog inputs for sensors or other signals
Two digital inputs for external control
Two relay outputs for controlling fans or dampers
LCD display and user-friendly menu structure for easy setup
Compact size and DIN rail mounting for easy installation
Pages: 196 Regin VCV203DWM-2 Manual
Brand: Regin Category: Thermostats Size: 27 MB
Languages: English
Table of contents
- 7 1About this manual
- 7 1.1 More information
- 8 2Introduction to Corrigo
- 8 2.1 Display
- 8 2.2 Application tool and Configuration of Corrigo
- 8 2.3 Internal web interface
- 9 2.4 Comparison between the user interfaces
- 10 3Information for the end user
- 10 3.1 Display, LED:s and buttons
- 11 3.1.1 Display
- 11 3.1.2 LED:s
- 12 3.1.3 Summary of the function of the buttons
- 12 3.2 Navigating the menus
- 13 3.3 Changing values
- 13 3.3.1 Editing an existing value
- 14 3.3.2 Enter a completely new value
- 14 3.3.3 Confirm the change
- 14 3.3.4 Undo an initiated change
- 14 3.4 Logging on and off
- 14 3.4.1 Log on
- 15 3.4.2 Log off
- 15 3.4.3 Change password
- 16 3.4.4 Automatic logoff
- 16 3.5 Menu structure and features
- 17 3.5.1 Ventilation
- 17 3.5.2 Additional function (extra controller)
- 18 3.5.3 Time settings
- 21 3.5.4 Inputs/Outputs
- 21 3.5.5 Mode switch
- 21 3.6 Alarm events and alarm handling
- 22 3.6.1 Alarm priorities
- 22 3.6.2 Inspect alarms
- 22 3.6.3 Acknowledge, block and unblock alarms
- 22 3.7 Internal web interface
- 23 3.7.1 Overview picture
- 24 3.7.2 Log in
- 24 3.7.3 Homescreen
- 27 3.7.4 Change timer settings
- 27 3.7.5 Setpoints
- 28 3.7.6 Signal analyzer (trend)
- 31 4Information for the specialist - Function descriptions
- 31 4.1 Function overview
- 33 4.2 Temperature control
- 33 4.2.1 General
- 34 4.2.2 Control modes
- 44 4.3 Temperature sequences
- 45 4.3.1 Heater (Sequence A)
- 50 4.3.2 Exchanger (Sequence B)
- 55 4.3.3 Cooler (Sequence C)
- 58 4.3.4 Damper sequence
- 60 4.3.5 Sequence Fan setpoint compensation
- 60 4.3.6 Change-over
- 61 4.3.7 Step controller
- 62 4.3.8 Support control
- 64 4.3.9 Free cooling
- 65 4.3.10 Cooling recovery
- 65 4.3.11 Enthalpy control
- 66 4.3.12 Heat exchanger efficiency monitoring
- 67 4.3.13 External setpoint
- 67 4.3.14 Recirculation
- 68 4.3.15 Extra temperature sensor
- 70 4.4 Fan control
- 70 4.4.1 General
- 75 4.4.2 Fan control types
- 79 4.4.3 Demand controlled ventilation
- 80 4.4.4 Extra fan motor control
- 81 4.5 Pump control
- 81 4.5.1 Heating circuit, water heating
- 81 4.5.2 Exchanger circuit, liquid connected exchangers
- 82 4.5.3 Cooling circuit
- 82 4.5.4 Settings and configuration in Application tool for pump control
- 82 4.5.5 Inputs and outputs for pump control
- 82 4.6 Damper control
- 82 4.6.1 Close-off dampers
- 83 4.6.2 Fire/smoke dampers
- 85 4.6.3 Inputs and outputs for dampers
- 85 4.7 Pretreatment
- 86 4.8 Humidity control
- 86 4.8.1 Humidification
- 86 4.8.2 Dehumidification
- 87 4.8.3 Humidification / Dehumidification
- 87 4.8.4 Digital humidity signal
- 87 4.8.5 Settings and configuration for Humidity control
- 88 4.8.6 Required inputs and outputs for humidity control
- 88 4.9 Filter monitoring
- 88 4.9.1 Settings and configuration for filter monitoring
- 89 4.10 Extended operation and External stop
- 90 4.11 Time-switch outputs
- 91 4.12 SFP, Specific Fan Power
- 91 4.13 Extra controller
- 92 4.14 Room unit
- 93 4.15 Energy consumption
- 94 5Information for the specialist - Configuration
- 94 5.1 Configuration of the Corrigo
- 94 5.1.1 Predefined configurations for Corrigo
- 95 5.1.2 Application tool
- 97 5.2 Work flow for configuration and commissioning the Corrigo
- 98 5.3 Configuration - System
- 98 5.3.1 General settings
- 100 5.3.2 Port 1 and Port 2
- 101 5.3.3 Modbus slave
- 101 5.3.4 BACnet
- 102 5.3.5 CLOUDigo
- 102 5.3.6 Display port
- 102 5.3.7 Unit settings
- 103 5.3.8 Save and restore
- 103 5.3.9 Controller address (PLA : ELA)
- 104 5.3.10 IP-configuration
- 104 5.4 Configuration - Device list
- 105 5.4.1 Fan (Modbus)
- 105 5.4.2 Rotary exchanger (Modbus)
- 106 5.4.3 Pressure transmitter (Modbus / EXOline)
- 106 5.4.4 Damper actuator
- 106 5.4.5 Expansion unit (EXOline)
- 106 5.4.6 Wireless receiver (Modbus)
- 107 5.4.7 Room unit (EXOline/Modbus)
- 107 5.5 Configuration - Functions
- 107 5.5.1 Function activation
- 115 5.5.2 Sequences
- 121 5.5.3 Fan control
- 124 5.5.4 Recirculation
- 124 5.5.5 Humidity control
- 125 5.5.6 Filter monitoring
- 125 5.5.7 Extended operation
- 125 5.5.8 Pretreatment
- 126 5.5.9 Extra controller
- 126 5.5.10 Extra fan motor control
- 126 5.5.11 Extra indications & outputs
- 127 5.5.12 Extra sensors & inputs
- 127 5.5.13 Room unit
- 127 5.5.14 Alarms
- 128 5.6 Configuration - Inputs and Outputs
- 128 5.6.1 Analog inputs, AI
- 129 5.6.2 Digital inputs, DI
- 129 5.6.3 Analog outputs, AO
- 130 5.6.4 Digital outputs, DO
- 130 5.7 Configuration - Raw values
- 130 5.8 Ventilation
- 130 5.8.1 Actual / Setpoint
- 136 5.8.2 Temperature control
- 138 5.8.3 Fan control
- 141 5.8.4 Demand control
- 142 5.8.5 Fire / Smoke
- 142 5.8.6 Humidity control
- 143 5.8.7 PID controllers
- 143 5.8.8 Energy consumption
- 145 5.8.9 Manual / Auto
- 149 5.8.10 Status
- 149 5.9 Additional function
- 149 5.9.1 Extra controller
- 150 5.9.2 Motor control 1 and 2
- 151 5.10 Inputs / Outputs
- 151 5.11 Time control
- 152 5.11.1 Extra time channels
- 152 5.11.2 Holiday calendar
- 153 5.11.3 Time settings in display and web interface
- 153 5.12 Alarm status
- 153 5.12.1 Alarm handling
- 153 5.12.2 Alarm configuration
- 154 5.13 Starting and stopping the Corrigo
- 154 5.13.1 Start and stop conditions in priority
- 155 5.13.2 Start sequence
- 156 5.13.3 Stop sequence
- 156 5.14 Changing the battery
- 156 5.14.1 24 V models (Corrigo Ardo)
- 157 5.14.2 230 V models (Corrigo Vido)
- 158 6Information for the installer
- 158 6.1 Installation
- 158 6.1.1 Corrigo Ardo (24 V)
- 161 6.1.2 Corrigo Vido (230 V)
- 163 6.1.3 Expansion units EXOline
- 164 6.2 Commissioning
- 164 6.2.1 Configuration using Application tool
- 164 6.2.2 Configuration in the web interface
- 165 6.3 Loading the application
- 167 Appendix ATechnical data
- 167 A.1 Corrigo Ardo
- 167 A.1.1 General data
- 167 A.1.2 Communication ports
- 167 A.1.3 Inputs & Outputs
- 168 A.2 Corrigo Vido
- 168 A.2.1 General data
- 168 A.2.2 Communication ports
- 168 A.2.3 Inputs & Outputs
- 169 Appendix BModel overview
- 169 B.1 Corrigo Ardo - Model overview
- 169 B.2 Corrigo Vido - Model overview
- 171 Appendix CInput and output lists
- 171 C.1 Analog inputs
- 172 C.2 Digital inputs
- 173 C.3 Universal inputs
- 173 C.4 Analog outputs
- 174 C.5 Digital outputs
- 177 Appendix DAlarm list
- 177 D.1
- 184 Appendix ETerminal lists
- 184 E.1 Corrigo Ardo (24 V models)
- 185 E.2 Corrigo Vido (230 V models)
- 187 Appendix FFrequency converters and EC controllers for heat exchangers
- 187 F.1 Vacon NXL
- 188 F.2 Lenze
- 188 F.3 Omron V1000
- 188 F.3.1 Parameters
- 189 F.4 Emerson Commander
- 190 F.4.1 Termination resistor
- 190 F.4.2 Terminals
- 190 F.4.3 Parameters
- 190 F.4.4 Changing parameters
- 191 F.5 LS
- 191 F.5.1 LS iG5A
- 191 F.5.2 LS iS7
- 192 F.6 EBM-PAPST
- 192 F.7 EC Blue
- 193 F.8 Danfoss FC 101
- 193 F.9 Eltwin A/S EC controller (for heat exchangers), RHC 200
- 194 F.10 VariMax25M
Other manuals and documents
Frequently Answers and Questions
How do I set up the control functions?
The control functions are easily set up via the LCD display and the user-friendly menu structure.
What is the size of the controller?
The controller is compact and DIN rail mounted.
Where can I install the controller?
The controller can be installed in electrical cabinets or other confined spaces.
advertisement