STMicroelectronics L99DZ200G
Manuals and User Guides for STMicroelectronics L99DZ200G. We found 1 manuals for free downloads Data Sheet
Pages: 198 STMicroelectronics L99DZ200G Data Sheet
Brand: STMicroelectronics Category: Electrical equipment & supplies Size: 4 MB
Languages: English
Table of contents
- 0 Description
- 0 Block diagram and pin descriptions
- 1 Electrical specifications
- 1 Absolute maximum ratings
- 3 ESD protection
- 3 Thermal data
- 4 LQFP64 thermal data
- 7 Electrical characteristics
- 7 Supply and supply monitoring
- 9 Oscillator
- 9 Power-on reset (VSREG)
- 10 Voltage regulator V
- 12 Reset output
- 13 Watchdog timing
- 15 Current monitor output (CM)
- 16 Charge pump
- 17 Outputs OUT1 - OUT15, ECV, ECDR
- 18 Power outputs switching times
- 20 Current Monitoring
- 23 Heater
- 23 H-bridge driver
- 24 Gate drivers for the external Power-MOS switching times
- 28 Drain source monitoring external H-bridges
- 28 Drain source monitoring external heater MOSFET
- 29 Open-load monitoring external H-bridges
- 29 Open-load monitoring external heater MOSFET
- 29 Electro-chrome mirror driver
- 30 Fail safe low-side switch
- 31 Wake up input WU
- 31 High speed CAN transceiver
- 37 LIN transceiver
- 63 Inputs TxD_C and TxD_L for Flash mode
- 64 PWMH(1/2)A, PWMH(1/2)B and DIR inputs
- 64 ADC characteristics
- 65 Temperature diode characteristics
- 65 Interrupt outputs
- 67 Timer1 and Timer
- 67 SGND loss comparator
- 68 Application information
- 68 Supply Vs, Vsreg
- 68 Voltage Regulators
- 68 Voltage regulator: V
- 69 Voltage Regulator Failure
- 69 Short to ground detection
- 70 Voltage regulator behavior
- 70 Operating Modes
- 71 Active Mode
- 71 Flash Modes
- 71 SW-Debug Mode
- 73 V1_Standby mode
- 74 Interrupt
- 75 CAN wake-up signalization
- 75 VBAT_Standby mode
- 75 Wake up from Standby Modes
- 76 Wake up inputs
- 77 Functional Overview (truth table)
- 78 Configurable Window Watchdog
- 81 Change Watchdog timing
- 81 Fail Safe Mode
- 81 Temporary Failures
- 82 Non-recoverable failures – forced VBAT_Standby mode
- 84 Reset output (NReset)
- 85 LIN Bus Interface
- 85 Features
- 86 Error Handling
- 86 Wake up from Standby Modes
- 87 Receive-only mode
- 88 High-speed CAN bus transceiver
- 88 Features
- 89 CAN Transceiver operating modes
- 90 Automatic Voltage Biasing
- 90 Wake up by CAN
- 91 CAN looping
- 91 Pretended Networking
- 91 CAN Error Handling
- 92 Serial Peripheral Interface (ST SPI Standard)
- 93 Power Supply Fail
- 93 Vs supply failure
- 94 Vsreg supply failure
- 96 Temperature warning and thermal shut-down
- 97 Power Outputs OUT
- 98 Auto-recovery alert and thermal expiration
- 100 Charge Pump
- 100 Inductive Loads
- 100 Open-load detection
- 100 Overcurrent Management: Recovery or Latch
- 101 Overcurrent Recovery and Short-Circuit detection
- 103 Constant current mode
- 104 Current monitor and direct drive input
- 105 PWM-Mode of the Power-Outputs
- 105 Cross-current protection
- 106 H-bridge control
- 108 H-Bridge Driver Slew-Rate Control
- 109 Resistive low
- 109 Short circuit detection / drain source monitoring
- 110 H-Bridge-Monitoring in Off-Mode
- 113 Programmable cross current protection
- 114 Power window H-bridge safety switch off block
- 116 Generator mode
- 116 Generator Mode in Active Mode
- 116 Generator Mode in Standby Modes
- 117 Heater MOSFET Driver
- 118 Controller of electro-chromic glass
- 120 Temperature warning and shutdown
- 120 Thermal clusters
- 122 VS compensation (duty cycle adjustment) module
- 123 Analog digital converter
- 125 Serial Peripheral Interface (SPI)
- 125 ST SPI
- 126 Physical Layer
- 126 Signal description
- 127 Clock and data characteristics
- 128 Communication Protocol
- 131 Address Definition
- 137 Protocol Failure Detection
- 139 Application
- 140 SPI registers
- 140 Global Status Byte GSB
- 144 Control register overview
- 148 Status register overview
- 150 Control registers
- 150 Control Register CR1 (0x01)
- 153 Control Register CR2 (0x02)
- 156 Control Register CR3 (0x03)
- 158 Control Register CR4 (0x04)
- 159 Control Register CR5 (0x05)
- 161 Control Register CR6 (0x06)
- 162 Control Register CR7 (0x07)
- 163 Control Register CR8 (0x08)
- 166 Control Register CR9 (0x09)
- 167 Control Register CR10 (0x0A)
- 169 Control Register CR11 (0x0B)
- 170 Control Register CR12 (0x0C)
- 172 Control Register CR13 (0x0D) to CR16 (0x10)
- 173 Control Register CR17 (0x11) to CR20 (0x14)
- 174 Control Register CR21 (0x15)
- 176 Control Register CR22 (0x16)
- 177 Configuration Register (0x3F)
- 180 Status registers
- 180 Status Register SR1 (0x31)
- 182 Status Register SR2 (0x32)
- 184 Status Register SR3 (0x33)
- 186 Status Register SR4 (0x34)
- 187 Status Register SR5 (0x35)
- 188 Status Register SR6 (0x36)
- 189 Status Register SR7 (0x37) to SR9 (0x39)
- 190 Status Register SR10 (0x3A)
- 191 Status Register SR11 (0x3B)
- 192 Status Register SR12 (0x3C)
- 193 Package information
- 193 LQFP-64 package information
- 195 LQFP-64 marking information
- 196 Order code
- 197 Revision history
advertisement