Agilent Technologies E8364C Specifications

Agilent

PNA Family

Microwave Network Analyzers

Configuration Guide

PNA-X N5241A

PNA-X N5242A

PNA-X N5244A

PNA-X N5245A

PNA E8362C

PNA E8363C

PNA E8364C

PNA E8361C

PNA N5250C

PNA-L N5230C

10 MHz to 13.5 GHz

10 MHz to 26.5 GHz

10 MHz to 43.5 GHz

10 MHz to 50 GHz





10 MHz to 110 GHz

300 kHz to 6, 13.5, or 20 GHz,

10 MHz to 20, 40, or 50 GHz

This configuration guide describes standard configurations, options, accessories, upgrade kits and compatible peripherals for the PNA family microwave network analyzers. This guide should be used with the Agilent PNA family data sheets for a complete description of these analyzers.

2

Table of Contents

PNA-X Series Network Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

PNA-X Noise Figure Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Test set and power confi guration options . . . . . . . . . . . . . . . . . . . . . . . . 7, 8

Measurement applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 10

Nonlinear vector network analysis . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Pulse, antenna, millimeter-wave . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Upgrade kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13

PNA Series Network Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Test set and power confi guration options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Measurement applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Pulse, antenna, millimeter-wave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Confi guration details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Simplifi ed test set block diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-21

N5250C millimeter-wave system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 23

Upgrade kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

PNA-L Series Network Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Test set and power confi guration options . . . . . . . . . . . . . . . . . . . . . . . . . 26

Measurement applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Upgrade kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Measurement Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Calibration kits, cables, adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

For devices with 1.0 mm connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

For devices with 1.85 mm connectors . . . . . . . . . . . . . . . . . . . . . . . . . . 30

For devices with 2.4 mm connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

For devices with K (2.92 mm) connectors . . . . . . . . . . . . . . . . . . . . . . . . . 31

For devices with 3.5 mm or SMA connectors . . . . . . . . . . . . . . . . . . . . . 33, 34

For devices with Type-N connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

For devices with 7 mm connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

For devices with waveguide . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35, 36

Verifi cation kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

General Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Power meters and sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Amplifi ers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Couplers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Equipment rack accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Printers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Interface cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Agilent offers the following options for all PNA family network analyzers

Certification options

□

Commercial calibration certification with test data (Option UK6)

Complete set of measurements which tests unit to manufacturer’s published specifications. Includes calibration label, calibration certificate, and data report. Conforms to ISO 9001.

Documentation

The PNA Series instruments are equipped with an Online Help system available within the instrument in the following languages:

English, Japanese, Chinese, German, Spanish, and French. Service guides and the Online Help system are available on the web: www.na.tm.agilent.com/pna

□

ISO 17025 compliant calibration (Option 1A7)

Complete set of measurements which tests unit to manufacturer’s published specifications. Includes calibration label, ISO 17025 calibration certificate, and data report, measurement uncertainties and guardbands on all customer specifications. Conforms to ISO

17025 and ISO 9001.

Calibration Software Licenses

□

Perpetual license for built-in performance test software for

Agilent inclusive cal (Option 897)

Adds built-in performance testing and calibration software for self-maintainers. Requires additional equipment. See the analyzer’s

Service Guide for more information on equipment required.

□

ANSI Z540 compliant calibration (Option A6J)

Complete set of measurements which tests unit to manufacturer’s published specifications. Includes pre- and post-adjustment data with measurement uncertainty information compliant to the

ANSI/NCSL Z540 standard.

□

Perpetual license for built-in performance test software for

Standards compliant cal (Option 898)

Adds built-in performance testing and calibration software for self-maintainers. Requires additional equipment. See the analyzer’s

Service Guide for more information on equipment required.

Warranty and service

1-, 3-, and 5-year warranty and service plans are available at the time of instrument purchase. Standard warranty is 1 year.

3

4

PNA-X Series Network Analyzer

N5241A

N5242A

10 MHz to 13.5 GHz

10 MHz to 26.5 GHz

N5244A

N5245A

10 MHz to 43.5 GHz


Option configurations

To add options to a product, order the corresponding item number.

Description For N5241A For N5242A

Test set

Option 200 2-ports, single source

Option 224 2-ports, add internal

2nd source, combiner

N5241A-200 N5242A-200

N5241A-224 N5242A-224

Option 400 and mechanical switches

4-ports, dual source N5241A-400 N5242A-400

Option 423 4-ports, add internal combiner N5241A-423 N5242A-423 and mechanical switches

For N5244A

N5244A-200

N5244A-224

For N5245A Additional information

N5245A-200

N5245A-224 Requires Options 200, one of 219 or

H85, and 080

N5244A-400

N5244A-423

N5245A-400 Option 080 recommended

N5245A-423 Requires Options 400, one of 419 or

H85, and 080

Power configuration

Option 219 2-ports, extended power range and bias-tees

N5241A-219 N5242A-219 N5244A-219 N5245A-219 Requires Option 200

Option 419 4-ports, extended power range N5241A-419 and bias-tees

Option H851 High power configurable

N5242A-419 N5244A-419 N5245A-419 Requires Option 400,

Option 080 recommended

N5241AS-H85 N5242AS-H85 N5244AS-H85 N5245A-H85 Requires Option 200 for 2-port,

(for 2- or 4-port)

Measurement applications

Option 400 for 4-port

Option 010 Time-domain measurements N5241A-010 N5242A-010

Option 028 2 Noise figure measurements

N5244A-010 N5245A-010

N5241A-028 N5242A-028 N5244A-028 N5245A-028 Requires Option 080

Option 029

Option H29

2

2 using standard receivers

Fully-corrected noise figure measurements

Add 26.5 GHz noise receivers

N5241A-029 N5242A-029

N/A N/A

Option 080 Frequency offset

Option 082

3

Scalar-calibrated converter

N5241A-080

N5241A-082

N5242A-080

N5242A-082

Option 083 3 measurements

Vector- and scalar-calibrated N5241A-083 N5242A-083

N/A

N5244A-083

N/A

N5245A-083

Requires one of Options 219, 224

419, 423, or H85, and Option 080

N5244AS-H29 N5245AS-H29 Requires Option 423

N5244A-080

N5244A-082

N5245A-080

N5245A-082 Requires Option 080

Requires Option 080 converter measurements

Option 084 Embedded LO measurements N5241A-084 N5242A-084

Option 086 Gain compression application N5241A-086 N5242A-086

Option 087 Intermodulation distortion application

N5241A-087 N5242A-087

Option 460 Integrated true-mode stimulus N5241A-460 N5242A-460 application

Option 551

4

N5244A-084

N5244A-086

N5244A-087

N5244A-460

N5245A-084

N5245A-460

Requires at least one of Options

028, 029, H29, 082, 083, or 087

N5245A-086 Options 219, 419 or H85 recommended

N5245A-087 Requires Options 224 or 423

Requires Option 400

Nonlinear vector network analysis

Option 510 Nonlinear component characterization

Option 514 Nonlinear X-parameters

5

Option 518 Nonlinear pulse envelope domain

Option 520 Arbitrary load-impedance

X-parameters

N5241A-510

N5241A-514

N5241A-518

N5241A-520

N5242A-510

N5242A-514

N5242A-518

N5242A-520

N5244A-510

N5244A-514

N5244A-518

N5244A-520

N5245A-510 Requires Options 419 and 080, or

400, H85 and 080

N5245A-514 Requires Options 423 and 510

N5245A-518 Requires Options 021 and 025

N5245A-520 and either one of 510 or 514

Requires Option 514

Required NVNA accessories

• U9391C 10 MHz to 26.5 GHz or U9391F 10 MHz to 50 GHz comb generator (two required for nonlinear measurements)

• Agilent power meter and sensor or USB power sensor

• Agilent signal generator, MXG or PSG used for X-parameter extraction (internal 10 MHz reference output can be used for 10 MHz tone spacing applications)

1. Order special model N524xAS instead of N524xA and add items N524xA-200 and N524xAS-H85 for 2-port, extended power range, high power configuration,

or items N524xA-400 and N524xAS-H85 for 4-port, extended power range, high power configuration. Order N524xA-xxx items for other standard options.

Option H85 modifies the extended power range and bias-tees (Options 219 and 419), and therefore, they cannot be ordered together.

2. For source-corrected measurements, Options 028, 029, and H29 require an ECal module for use as an impedance tuner. For calibration, Options 029 and

H29 also require a 346-series noise source (Agilent 346C recommended), while Option 028 requires a power meter. All options require a power meter for

measuring mixers and converters.

3. Option 082 is a subset of Option 083; therefore, they cannot be ordered together.

4. When configured as a multiport analyzer using Option 551 and a multiport test set, the combiner feature of Option 224 or 423 is temporarily disabled.

When configured as a standalone analyzer, the combiner feature is enabled. When ordering a test set, select an option to specify the appropriate

interconnect jumper cable set between the analyzer and the test set.

5. X-parameters is a trademark of Agilent Technologies


Option configurations (continued)


Description

Pulse, antenna, mm-wave

For N5241A For N5242A For N5244A For N5245A Additional information

Option 020 Add IF inputs for antenna and mm-wave

Option 021 Add pulse modulator to internal 1st source

Option 022 Add pulse modulator to internal 2nd source

Option 025 Add four internal pulse generators

N5241A-020

N5241A-021

N5241A-022

N5241A-025

N5242A-020

N5242A-021

N5242A-022

N5242A-025

N5244A-020

N5244A-021

N5244A-022

N5244A-025

N5245A-020

N5245A-021

N5245A-022

N5245A-025

Option 118 Fast CW sweep

Accessories

Option 1CM Rack mount kit for use without handles

N5241A-118

N5241A-1CM

N5242A-118

N5242A-1CM

N1966A

N4688A

Pulse I/O adapter

USB CD R/W drive

N1966A

N4688A

N1966A

N4688A

Calibration software

Option 897

1

Perpetual license for built-in N5241A-897 N5242A-897 performance test software for

Option 898

1

Agilent inclusive calibration

Perpetual license for built-in N5241A-898 N5242A-898 performance test software for standards compliant calibration

N5244A-118

N5244A-1CM

N1966A

N4688A

N5244A-897

N5244A-898

N5245A-118

N5245A-1CM

N1966A

N4688A

N5245A-897

N5245A-898

Requires Option 224 or 400

Calibration documentation

Option 1A7 ISO 17025 compliant calibration N5241A-1A7 N5242A-1A7 N5244A-1A7 N5245A-1A7 with test data

Option A6J ANSI Z540 compliant calibration N5241A-A6J N5242A-A6J N5244A-A6J N5245A-A6J

1. Additional hardware required. Please refer to the analyzer’s Service Guide for required service test equipment.

5


The PNA-X is an integrated vector network analyzer featuring a built-in S-parameter test set, one or two synthesized sources used for device stimulus, a hard disk drive, USB interfaces, and a

10.4” LCD touch screen display. The N5241A and the N5242A have 50 ohm, ruggedized 3.5 mm (m) test ports. The N5244A and the N5245A have 50 ohm, ruggedized 2.4 mm (m) test ports.

Included with each instrument is a mouse, keyboard (U.S. style), and a 1-year return-to-Agilent service warranty.

Test set and power configuration options

• 2-port standard test set and power range (Option 200)

The standard 2-port test set comes with six front-panel access

loops. The loops provide access to the signal path between

(a) the source output and the reference receiver, (b) the source

output and directional coupler thru arm and (c) the coupled

arm of the directional coupler and the port receiver. The standard

test set also includes a solid-state internal RF transfer switch

in the R1 reference-receiver path.

OUT 1

Source 1

OUT 2

• Extended power range and bias-tees (Option 219, 419)

Adds to the standard test set one 65 dB for N5241A/42A

and 60 dB for N5244A/45A source attenuator (settable in 5 dB

increments for N5241A/42A and 10 dB increments for

N5244A/45A), one 35 dB receiver attenuator (settable in 5 dB

increments), and one bias-tee to each test port. Option 219

requires Option 200, and Option 419 requires Option 400.

OUT 1

Source 1

OUT 2

R1

65 dB

Test port 1

A

35 dB

R2

65 dB

Test port 2

B

35 dB

R1

A

R2

B

Test port 1 Test port 2

• 4-port standard test set, power range and an internal second

source (Option 400)

The standard 4-port test set comes with 12 front-panel access

loops and a built-in second source. The loops provide access to

the signal path between (a) the source output and the reference

receiver, (b) the source output and directional coupler thru arm

and (c) the coupled arm of the directional coupler and the port

receiver. The internal second source provides an additional signal

(fixed or swept) for two-tone third-order-intercept (TOI) and

intermodulation testing of amplifiers, or it can be used as a fast

swept-LO signal for fixed-IF testing of mixers and converters.

With two sources, source 1 is accessible through test ports 1

and 2, and source 2 is accessible through test ports 3 and 4.

The standard test set also includes a solid-state internal RF

transfer switch in the R1 reference-receiver path. Recommends

OUT 1

Source 1

OUT 2

OUT 1

Source 2

OUT 2

R1

65 dB

Test port 1

R3

A

35 dB

65 dB

Test port 3

C

35 dB

R4

65 dB

Test port 4

R2

D

35 dB

65 dB

Test port 2

B

35 dB

R1

A

R3

OUT 1

Source 1

OUT 2

OUT 1

Source 2

OUT 2

C

R4

D

R2

B

Test port 1 Test port 3 Test port 4 Test port 2


• Add an internal second source, a combiner and mechanical switches to 2-port analyzer (Option 224)

Available with 2-port model only, this option adds an internal second source, a combiner and mechanical switches. The internal second source provides an additional signal (fixed or swept) for two-tone third-order-intercept (TOI) and intermodulation testing of amplifiers, or it can be used as a fast swept-LO signal for fixed-IF testing of mixers and converters. The mechanical switches provide increased flexibility by having rear panel access to signal paths for advanced applications. Access to the second source is available through two output connectors on the front panel. Requires Options 200, 219 and 080.

rear panel

J11 J10 J9 J8 J7 J2 J1

• High-power test set (Model N524xAS Option H85)

With extended power range and bias-tees (Option 219, 419), the internal bias tees limit the maximum test port input power to +30 dBm. The high-power test set removes the bias tees between the source attenuators and the test port couplers. This extends the maximum port power that the analyzer can safely handle to +43 dBm. Selecting Option H85 adds internal attenuators and cables (Option 285 for 2-port or Option 485 for 4-port analyzers).

The high-power test set modifi es Options 219 and 419, and therefore, they can not be ordered together.

OUT 1

Source 1

OUT 2

OUT 1

Source 2

OUT 2

OUT 1

Source 2

OUT 2

OUT 1

Source 1

OUT 2

R1

Test port 1

A

Source 2

Output 1

Source 2

Output 2

R2

Test port 2

B

R1

65 dB

Test port 1

R3

A

35 dB

65 dB

Test port 3

R4

C

35 dB

65 dB

Test port 4

R2

D

35 dB

65 dB

Test port 2

B

35 dB

• Add an internal combiner and mechanical switches to 4-port analyzer (Option 423)

Available with 4-port model only, this option adds a combiner and mechanical switches. The mechanical switches provide increased flexibility by having rear panel access to signal paths for advanced applications. Requires Options 400, 419 and 080.

rear panel J11 J10 J9 J8 J7 J4 J3 J2 J1

OUT 1

Source 1

OUT 2

OUT 1

Source 2

(standard)

OUT 2

R1

A

R3

C

R4

D

R2

B


7



□

Time domain (Option 010)

This option enables the PNA-X to view reflection and

transmission responses in time or distance. Use time domain

to tune filters, gate out the response of fixtures and cables,

characterize the impedance of transmission lines and more.

□

Frequency offset (Option 080)

This option enables the PNA-X to set the source frequency

independently from where the receivers are tuned. This ability

is important for measuring amplifiers, mixers, and frequency

converters.

□

Scalar-calibrated converter measurements (Option 082)

With a simple setup and calibration, this application delivers

the highest accuracy for scalar conversion-loss/gain measure-

ments by combining one-port and power-meter calibrations to

remove mismatch errors. Option 082 provides an intuitive and

easy-to-use user interface for setting up mixer and converter

measurements, with single or dual conversion stages. It can

control the PNA-X’s built-in second source as well as external

signal generators for use as LO signals. Supported external

sources include the Agilent ESG, PSG, and MXG series, as

well as other SCPI-controlled signal generators. Option 082

requires Option 080, and cannot be ordered with Option 083.

It is compatible with Option 084, which enables measurements

of converters with internal LOs.

□

Vector- and scalar-calibrated converter measurements (Option 083)

This application includes the new scalar mixer/converter +

phase measurement class which provides fully calibrated con

version gain/loss, relative phase, and absolute group delay

measurements of mixers and converters without the need for

a reference mixer. A vector mixer/converter measurement

class is also included for measurements with the least

amount of trace noise for phase/delay measurements. Option

083 provides an intuitive and easy-to-use user interface for

setting up mixer and converter measurements, with single or

dual conversion stages. It can control the PNA-X’s built-in

second source as well as external signal generators for use as

LO signals. Supported external sources include the Agilent

ESG, PSG, and MXG series, as well as other SCPI-controlled

signal generators. Option 083 requires Option 080, and cannot

be ordered with Option 082. It is compatible with Option 084,

which enables measurements of converters with internal LOs.

□

Embedded LO measurements (Option 084)

This option tunes the PNA-X receivers to the output frequency

of the converter under test, without the need for access to

internal LOs or a common reference signal. For converters

with embedded LOs, this option enables measurements of

match-corrected conversion loss/gain (requires Option 082 or 083),

absolute group delay (requires Option 083), intermodulation dis-

tortion (requires Option 087), and noise figure (requires Option 028,

029, or H29).

8

□

Gain compression application (Option 086)

The Gain Compression Application (GCA) provides input power,

output power, gain, and phase at an amplifier's compression

point, over a specified frequency and power range. GCA's

SMART Sweep is very fast and easy-to-use. GCA also includes

a guided calibration that corrects for absolute power levels,

frequency response, and mismatch errors.

□

Intermodulation distortion application (Option 087)

The intermodulation distortion (IMD) application makes it very

easy to set up and calibrate swept-IMD measurements of

both amplifiers and frequency converters. It uses the built-in

second source and internal combiner of the PNA-X (requires

Option 224 or 423). The user can sweep either the center

frequency of the two stimulus signals, the frequency spacing

of the two stimulus signals about a fixed center frequency, or

the power of one or both stimulus signals or the power of the

LO signal. The analyzer can measure intermodulation distortion

products of order 2, 3, 5, 7, or 9, and can display the associated

intercept points. In addition, an IM Spectrum mode gives a

spectrum-analyzer-like display for confirming or trouble-shooting

measurements. Requires firmware A.08.33 and above.

□

Integrated true-mode stimulus application (Option 460)

Integrated true-mode stimulus application (iTMSA) provides

mismatch-corrected true-mode (true differential and true

common) stimulus and enables accurate balanced measure-

ments under real operating conditions. iTMSA also provides

balanced measurements with forward-only sweep, reverse-only

sweep, and frequency or power sweep with arbitrary phase

and amplitude offsets. Requires firmware A.08.20 and above.

□

N-port capabilities (Option 551)1

Adds a multiport analyzer mode to the PNA-X network analyzer,

that enables full N-port error correction and measurement

capabilities using an external test set. Only standard measure-

ment class is available in the multiport analyzer mode.

1. When configured as a multiport analyzer using Option 551 and a multi-

port test set, the combiner feature of Option 224 or 423 is temporarily

disabled. When configured as a standalone analyzer, the combiner

feature is enabled. When ordering a test set, select a test set option

to specify an appropriate interconnect jumper cable set between the

analyzer and the test set.



(continued)

□

Noise figure measurements using standard receivers (Option 028)

This option adds firmware for high-accuracy noise figure measure-

ments of amplifiers, frequency converters, and mixers using the

PNA-X’s standard receivers, and utilizing Agilent’s unique source-

correction technique. Using the PNA-X and an Agilent ECal module

configured as an impedance tuner, the effects of imperfect system

source match are removed, greatly improving the accuracy of the

cold-source technique. This approach surpasses the accuracy pro-

vided by the Y-factor method. For fully corrected noise figure mea-

surements, this option requires an ECal module (m-f recommended)

and a power meter (both must be ordered or supplied separately). A

scalar calibration choice is also available that offers less accuracy,

but is faster and does not require the ECal module used as an

impedance tuner. The power meter is only used during calibration of

the analyzer. During calibration of the analyzer, an additional ECal or

mechanical calibration kit is required (also must be ordered or sup-

plied separately). To use a m-f ECal module as a tuner (N4691B/

93A-M0F), Option 028 includes a semi-rigid cable (3.5 mm N5242-

20137 for N5241/42A or 2.4 mm N5245-20140 for N5244/45A) and

a m-f adapter (3.5 mm 85052-60013 for N5241/42A or 2.4 mm

85056-60007 for N5244/45A). For use with f-f ECal modules

(N4691B/93A-00F), order a m-m adapter (3.5 mm 85052-60014 or

2.4 mm 85056-60005). No external preamplifier is required for

devices with 30 dB or more of excess noise (gain plus noise figure).

Front panel jumpers provide a convenient spot for adding a pre-

amplifier and filter(s) for low gain, low noise figure devices.

□

Fully-corrected noise figure measurements (Option 029)

This option adds high-sensitivity noise receivers and firmware

for high-accuracy noise figure measurements of amplifiers,

frequency converters, and mixers, utilizing Agilent’s unique

source-correction technique. Using the PNA-X and an Agilent

ECal module configured as an impedance tuner, the effects of

imperfect system-source match are removed, greatly improv

ing the accuracy of the cold-source technique. This approach-

surpasses the accuracy provided by the Y-factor method. For

fully corrected noise figure measurements, this option requires

a 3.5 mm N4691B ECal module (m-f recommended) and a

346C noise source (both must be ordered or supplied sepa-

rately). A scalar calibration choice is also available that offers

less accuracy, but is faster and does not require the ECal mod-

ule used as an impedance tuner. For measurements of mixers

and converters, a power meter is also required. The noise

R1

J11 J10 J9 J8

OUT 1

Source 1

A

Test port 1

OUT 2

J7

OUT 1

Source 2

Source 2

Output 1

OUT 2

Source 2

Output 2 rear panel

R2

J2 J1

10 MHz -

3 GHz

Test port 2

Noise receivers

B

3 -26.5 GHz

source and power meters are only used during calibration of

the analyzer. During calibration of the analyzer, an additional

ECal or mechanical calibration kit is required (also must be

ordered or supplied separately). To use a 3.5 mm m-f ECal

module as a tuner (N4691B-M0F), Option 029 includes a

3.5 mm semi-rigid cable (N5242-20137) and 3.5 mm m-f

adapter (85052-60013). For use with 3.5 mm f-f ECal modules

(N4691B-00F), order a 3.5 mm m-m adapter (85052-60014).

Option 029 also allows noise figure measurements using the

standard receivers for high-gain (> 60 dB) devices that might

otherwise overload the noise receivers.

□

Add 26.5 GHz noise receivers (Option H29)

This option adds 26.5 GHz high-sensitivity noise receivers to

N5244A 43.5 GHz and N5245A 50 GHz PNA-X models. The

option also enables use of the standard receivers for noise

figure measurements up to 43.5 or 50 GHz. Both receiver

choices yield high-accuracy noise figure measurements of

amplifiers, frequency converters and mixers, utilizing Agilent’s

unique source-correction technique. Using the PNA-X and an

Agilent ECal module configured as an impedance tuner, the

effects of imperfect system-source match are removed, greatly

improving the accuracy of the cold-source technique. This

approach surpasses the accuracy provided by the Y-factor

method. For fully corrected noise figure measurements, this

option requires an ECal module (2.4 mm N4693A m-f recom-

mended) and a 346C noise source (both must be ordered or

supplied separately). A scalar calibration choice is also available

that offers less accuracy, but is faster and does not require the

ECal module used as an impedance tuner. For measurements of

mixers and converters, a power meter is also required. The

noise source and power meter are only used during calibration

of the analyzer. During calibration of the analyzer, an additional

ECal or mechanical calibration kit is required (also must be

ordered or supplied separately). To use a 2.4 mm m-f ECal

module as a tuner (N4693A-M0F), Option H29 includes a 2.4 mm

semi-rigid cable (N5245-20140) and 2.4 mm m-f adapter (85056-

60007). For use with f-f ECal modules (N4693A-00F), order a

2.4 mm m-m adapter (85056-60005). For use with 3.5 mm m-f

ECal modules (N4691B-M0F), order two 2.4 mm to 3.5 mm m-f

adapters (11901C), plus a 3.5 mm semi-rigid cable (N5242-

20137) and a 3.5 mm m-f adapter (85052-60013). For use with

3.5 mm f-f ECal modules (N4691B-00F), order two 2.4 mm to

3.5 mm m-f adapters (11901C), plus a 3.5 mm semi-rigid cable

(N5242-20137) and a 3.5 mm m-m adapter (85052-60014).

9


PNA-X Noise Figure Options Summary

Overview

Description

Required options

Option 028

Noise fi gure application using standard receivers only, for all

PNA-X models.

080

No

No

Option 029

Noise fi gure application using standard or low-noise receivers, for N5241/42A models.

080 plus one of: 219, 224, 419,

423, or H85

Yes

Yes

Includes low-noise receivers

Includes fi lters for LO-harmonic rejection

Includes source tuner bypass switch

Use standard receivers for noise fi gure measurements

1

Vector noise calibration available

(using ECal as tuner)

Scalar noise calibration available

Recommended ECal for vector noise calibration

S-parameter, conversion gain/loss measurements

Max freq (GHz)

Noise fi gure measurements, amplifi ers

Max frequency, using low-noise receivers (GHz)

Max frequency, using standard receivers (GHz) 1

Calibration accessories for low-noise receivers

Calibration accessories for standard receivers

Noise fi gure measurements, converters

Max input frequency (GHz)

Max output frequency, using low-noise receivers (GHz)

Max output frequency, using standard receivers (GHz)

1

Calibration accessories for low-noise receivers

Calibration accessories for standard receivers

No

Yes

Yes

Yes

N4691B-M0F (41/42A),

N4693A-M0F (44/45A)

13.5/26.5/43.5/50

N/A

13.5/26.5/43.5/50

N/A

Cal kit or ECal, power meter

13.5/26.5/43.5/50

N/A

13.5/26.5/43.5/50

N/A


Yes

Yes

Yes

Yes

N4691B-M0F

13.5/26.5

13.5/26.5

13.5/26.5

Cal kit or ECal, 346C noise source


13.5/26.5

13.5/26.5

13.5/26.5

Cal kit or ECal, 346C noise source, power meter


Option H29

Noise fi gure application using standard or low-noise receivers, for N5244/45A models.

080, 423

Yes, up to 26.5 GHz

Yes, up to 26.5 GHz

Yes

Yes

Yes

Yes

N4693A-M0F

43.5/50

26.5

43.5/50

Cal kit or ECal, 346C noise source


43.5/50

26.5

43.5/50

Cal kit or ECal, 346C noise source, power meter


1. External preamp and filter(s) required if DUT gain + NF < 30 dB

10



Please refer to the Nonlinear Vector Network Analyzer brochure for more information 5989-8575EN


□

Pulsed-RF measurements (Option 008)

This option extends the pulsed-RF measurement capability of

the PNA-X to pulse widths below 267 ns, which is the limit for

the standard wideband detection mode. The PNA-X is a complete

pulsed-RF solution with built in pulse generators and modulators,

so external test sets and pulse generators are not required.

null out unwanted spectral components, enables the internal

receiver IF gates, controls internal pulse generators (Option 025),

internal pulse modulators (Option 021 and/or 022), and external

pulse modulators, and performs optimization for measurement

sensitivity. Option 008 also includes conventional pulsed-RF

measurement software (Option H08), which can run on the

PNA-X or an external computer. The N1966A pulse I/O adapter is

recomended using external pulse generators and/or external pulse

modulators.

□

Add IF inputs for antenna and millimeter-wave (Option 020)

This option enables external IF inputs on the rear panel of the

PNA-X for applications such as antenna and millimeter-wave

test.

□

Add pulse modulator to internal first source (Option 021)

This option enables the internal pulse modulator on source 1.

Control of the modulator can also be done via pin 8 of the

Pulse I/O D-sub connector on the rear panel of the PNA-X

using an external pulse generator, or by using one of the internal

pulse generators (Option 025). The N1966A pulse I/O adapter

is recommended if using an external pulse generator.

(See diagram below for details of the D-sub connector.)

□

Add pulse modulator to internal second source (Option 022)

This option enables the internal pulse modulator on source 2.

Control of the modulator can also be done via pin 8 of the

Pulse I/O D-sub connector on the rear panel of the PNA-X

using an external pulse generator, or by using one of the internal

pulse generators (Option 025). The N1966A pulse I/O adapter

is recommended if using an external pulse generator. Option 224

or 400 required. (See diagram for details of the D-sub connector.)

□

Add four internal pulse generators (Option 025)

This option enables four internal pulse generators. These

pulse generators can be used to control the internal pulse

modulators and internal receiver IF gates, and are also available

on pins 10 through 13 of the Pulse I/O D-sub connector on

the rear panel of the PNA-X to control external modulators

and/or gates. The N1966A pulse I/O adapter is recommended

if using external pulse modulators. (See diagram for details of

the D-sub connector.)

□

Fast CW Sweep (Option 118)

This option uses FIFO (fi rst-in fi rst-out) to allow external point-

trigger acquisition of 400,000 data points per second on fi ve

measurement receivers. When enabled, there is no display

update, no background computation, or other interference

from the vector network analyzer application. All the data

gathered is placed into a 500 million points FIFO buffer. While

the data is going into FIFO it can be read from the FIFO buffer.

Accessories

□

Rack mount kit without handles (Option 1CM)

Adds a rack mount (5063-9217) and rail kit (E3663AC) for use

□

Pulse I/O adapter (N1966A)

An adapter for connecting between the Pulse I/O connector on

the rear panel of the PNA-X and the coaxial inputs and outputs

of external pulse generators and external pulse modulators.

Coaxial connectors are SMB-male. The PULSE IN connectors

are for controlling the PNA-X's internal IF gates, which are

enabled with Option H08 and used with narrowband detection.

The PULSE OUT connectors are from the PNA-X's four internal

pulse generators, which are enabled with Option 025. The

PULSE SYNC IN connector is used to synchronize the internal

pulse generators with an external timing pulse. The RF PULSE

MOD IN connector controls the internal pulse modulator(s) which

are enabled with Options 021 and 022.

Pulse I/O adapter (N1966A) simplifies connections

8

1 5

7

1 4

6

1 3

5

1 2

4

1 1

3

1 0

2

9

1

Pulse I/O D-sub connector (DB-15 female)

11


Upgrade kits

Upgrade kits are available to add options after initial purchase. To upgrade the PNA-X, order the corresponding item number.

The model and serial numbers of the instrument to be retrofitted are required as part of the order.

Description

Frequency upgrade 1

N5242A Extend analyzer’s frequency

Required option For N5241A For N5242A For N5244A For N5245A User installable

N5245A range to 26.5 GHz

Extend analyzer’s frequency

N5241A

N5244A

N5241AU-960

N/A

N/A

N/A

N/A N/A

N5244AU-990 N/A

No

No

Test set range to 50 GHz

Option 224 2-ports, add internal 2nd source, Options 200, 219 N5241AU-922 N5242AU-922 N5244AU-922 N5245AU-922 No combiner and mechanical switches

Option 423 4-ports, add internal combiner and Options 400, 419 N5241AU-927 N5242AU-927 N5244AU-927 N5245AU-927 No mechanical switches


Option 219 2-ports, extended power range Option 200 and bias-tees

N5241AU-921 N5242AU-921

N5244AU-921 N5245AU-921 No

Option 419 4-ports, extended power range Option 400 and bias-tees

Option H85 High-power configurable

(for 2- or 4-port) 419 or 423

N5241AU-926

Option 219, 224, N5241AU-H85

N5242AU-926

N5242AU-H85

N5244AU-926 N5245AU-926

N5244AU-H85 N5245AU-H85

No

No


Option 010 Time-domain measurements

Option 028 Noise figure measurements using standard receivers

Option 029 Fully-corrected noise figure measurements for 2-port

Option 029 Fully-corrected noise figure measurements for 4-port or H85, and 080 or H85, and 080

Option H29 Add 26.5 GHz noise receivers Option 423

Option 080 Frequency offset

N5241AU-010

Option 219, 224, N5241AU-924

Option 419, 423, N5241AU-929

N/A

N5241AU-080

N5242AU-010

N5242AU-924

N5242AU-929

N/A

N5242AU-080

N/A

N/A

N5244AU-010 N5245AU-010

N5241AU-028 N5242AU-028 N5244AU-028 N5245AU-028

N/A

N/A

Yes

Yes

No

No

N5244AU-H29 N5245AU-H29 No

N5244AU-080 N5245AU-080 Yes

Option 082 Scalar-calibrated converter measurements

Option 083 Vector- and scalar-calibrated converter measurements

Option 084 Embedded LO measurements

Option 086 Gain compression application

Option 080

Option 080

N5241AU-082

N5241AU-083

N5242AU-082

N5242AU-083

N5244AU-082 N5245AU-082

N5244AU-083 N5245AU-083

Yes

Yes

Option 028, 029, N5241AU-084 N5242AU-084 N5244AU-084 N5245AU-084 Yes

H29, 082, 083, or

087

N5241AU-086 N5242AU-086 N5244AU-086 N5245AU-086 Yes

Option 087 Intermodulation distortion application

Option 460 Integrated true-mode stimulus Option 400 application

Option 551 N-port capabilities

Option 224 or 423

N5241AU-087

N5241AU-460

N5241AU-551

N5242AU-087

N5242AU-460

N5242AU-551

N5244AU-087 N5245AU-087

N5244AU-460 N5245AU-460

N5244AU-551 N5245AU-551

Yes

Yes

Yes


Option 510 Nonlinear component

Option 514 Nonlinear X-parameters

Option 518 Nonlinear pulse envelope

Option 520 characterization domain

Arbitrary load-impedance

X-parameters

Options 419 and N5241AU-510 N5242AU-510 N5244AU-510 N5245AU-510 Yes

080, or 400, H85 and 080

Options 423, N5241AU-514 N5242AU-514 N5244AU-514 N5245AU-514 Yes

510

Options 021, 025 N5241AU-518 N5242AU-518 N5244AU-518 N5245AU-518 Yes and either one of

510 or 514

Option 514 N5241AU-520 N5242AU-520 N5244AU-520 N5245AU-520 Yes

1. Frequency upgrade options from N5241A or N5242A to N5244A or N5245A are not available. Trade-in is recommended.

12


Upgrade kits (continued)

Upgrade kits are available to add options after initial purchase. To upgrade the PNA-X, order the corresponding item number.

The model and serial numbers of the instrument to be retrofitted are required as part of the order.

Description


Required option For N5241A

Option 008 Pulsed-RF measurements

Option 020 Add IF inputs for antenna and mm-wave

Option 021 Add pulse modulator to internal

Option 025 N5241AU-008

N5241AU-020

For N5242A

N5242AU-008

N5242AU-020

For N5244A For N5245A

N5244AU-008 N5245AU-008

N5244AU-020 N5245AU-020

User installable

Yes

Yes


1st source

Option 022 Add pulse modulator to internal Option 224 or 400 N5241AU-022 N5242AU-022 N5244AU-022 N5245AU-022 Yes

2nd source

Option 025 Add four internal pulse N5241AU-025 N5242AU-025 N5244AU-025 N5245AU-025 Yes generators

Option 118 Fast CW sweep N5241AU-118 N5242AU-118 N5244AU-118 N5245AU-118 Yes


Calibration Software

Option 897 Perpetual license for built-in performance test software for


Option 898 Perpetual license for built-in performance test software for standards compliant calibration


Frequency

13.5 GHz

N5241AU-960

26.5 GHz

43.5 GHz

N5244A-990

50 GHz

PNA-X upgrade path

2-port 4-port

944

942

200

921

940

922

224 219

219

029

924

922

224

029

924

400

926

419

927

929

419

029

927

423

929

423

029

H85

high power

H85

high power

13

PNA Series Network Analyzer 1

E8362C

E8363C

E8364C

10 MHz to 20 GHz

10 MHz to 40 GHz

10 MHz to 50 GHz

E8361C

N5250C 2



10 MHz to 67 GHz

10 MHz to 110 GHz

Description

Test set

Option 014 • Configurable test set

For E8362C For E8363C For E8364C For E8361C For N5250C Additional system 3

E8362C-014 E8363C-014 E8364C-014 E8361C-014 Included


Option UNL • Extended power range E8362C-UNL E8363C-UNL E8364C-UNL E8361C-UNL Included

and bias-tees

information

Only E8361C requires 014

Option 016 • Add receiver attenuators E8362C-016 E8363C-016

H85 7 • High-power configuration E8362CH85 E8363CH85

E8364C-016 E8361C-016

E8364CH85 Contact

Agilent

E8361C-016 Requires UNL

(only E8361C also

Contact Includes 014, 016,

Agilent UNL* 4 , 080, 081


Option 010 • Time-domain capability

Option 080 • Frequency offset

E8362C-010 E8363C-010

E8362C-080 E8363C-080

E8364C-010 E8361C-010 E8361C-010

E8364C-080 E8361C-080 Included Requires 014

(E8361C only, 081 required if UNL is also purchased)

Option 081 • Reference receiver switch E8362C-081 E8363C-081 E8364C-081 E8361C-081 Included Requires 014, 080

(only E8361C also

Option 082 • Scalar-calibrated

converter measurements

E8362C-082 E8363C-082 E8364C-082 E8361C-082 5 Requires 014, 080

Option 083 • Vector- and scalar-calibrated E8362C-083 E8363C-083 E8364C-083 E8361C-083 E8361C-083

5

converter measurements

Requires 014, 080,

081(only E8361C also requires UNL)

084

550

6

9

• Embedded LO measurements E8362C-084 E8363C-084 E8364C-084 E8361C-084 E8361C-084 Requires 082 or 083

551

9

• 4-port measurement application E8362C-550 E8363C-550 E8364C-550 E8361C-550 N/A

• N-port capabilities E8362C-551 E8363C-551

Requires 014

E8364C-551 E8361C-551 N/A Requires 014


Option H08 • Pulsed-RF measurement E8362C-H08

Option

E8363C-H08 E8364C-H08 E8361C-H08 E8361C-H08 5

H11

capability

• IF access (for antenna, E8362C-H11 E8363C-H11 E8364C-H11 E8361C-H11 Included

pulsed-RF and mm-wave

measurements)

Requires 014, 080

(Option H11 recommended)

Requires 014, UNL,

080, and 081

Accessories

Option 1CM • Rack mount kit for use

without handles

Option 1CP • Rack mount kit for use

N4688A

N4689A

with handles

• USB CD R/W drive

• USB Hub


Option 1A7 • ISO 17025 compliant

calibration

E8362C-1CM

E8362C-1CP

N4688A

N4689A

E8362C-1A7

E8363C-1CM

E8363C-1CP

N4688A

N4689A

E8363C-1A7

E8364C-1CM

E8364C-1CP

N4688A

N4689A

E8364C-1A7

E8361C-1CM E8361C-1CM

E8361C-1CP E8361C-1CP

N4688A

N4689A

N4688A

N4689A

E8361C-1A7 E8361C-1A7

Option UK6 • Commercial calibration E8362C-UK6 E8363C-UK6 E8364C-UK6 E8361C-UK6 E8361C-UK6

certificate with test data

Option A6J • ANSI Z540 compliant

calibration

Calibration software for self-maintainers

897 8

E8362C-A6J E8363C-A6J

performance test software for Agilent exclusive calibration

E8364C-A6J E8361C-A6J E8361C-A6J

898 8

performance test software for standards compliant calibration

1. All models are not available in all countries.

2. For more detailed information regarding the 110 GHz network analyzer system, refer to the Agilent Web site: www.agilent.com/find/pna

and download the N5250C Technical Overview, literature number 5989-7620EN.

3. The N5250C 110 GHz system also includes an N5260A millimeter-wave test set controller, 1.0 mm combiner assembly, interconnect cables,

and installation and productivity assistance.

4. UNL* does not include bias-tees. Only includes source attenuators.

5. Up to 67 GHz.

6. Requires firmware A.07.05 and above, plus 1.1 GHz CPU board.

7. Option H85 is ordered as a separate model, as indicated.


9. Option 550 is a subset of 551; therefore they cannot be ordered together. When ordering a test set, select an option to specify the appropriate


14

PNA Series Network Analyzer

The microwave PNA Series instruments are integrated vector network analyzers equipped with a built-in S-parameter test set, synthesized source, a hard disk drive, USB interfaces, and an

8.4” LCD color touch screen display. The E8362C has 3.5 mm male 50-ohm test ports. The E8361C has 1.85 mm male 50-ohm test ports. Included with each instrument is a mouse, keyboard

(U.S.) and a 1-year return-to-Agilent service warranty.

●

E8362C network analyzer, 10 MHz to 20 GHz

●


●


●

E8361C network analyzer, 10 MHz to 67 GHz 1

●

N5250C network analyzer system, 10 MHz to 110 GHz


□

Configurable test set (Option 014) 2

Provides six front panel access loops. Three access loops are

for port one and three for port two. The loops provide access

to the signal path between (a) the source output and the

reference receiver, (b) the source output and directional coupler

thru arm and (c) the coupled arm of the directional coupler and

the port receiver. This option provides the capability to improve

instrument sensitivity for measuring low-level signals, to

reverse the directional coupler to achieve even more dynamic

range or to add components and other peripheral instruments

for a variety of measurement applications. (see PNA Series

Microwave Data Sheet literature number 5989-7605EN for a

basic block diagram)

□

Extended power range and bias-tees (Option UNL) 2

Adds two 60 dB step attenuators and two bias-tees to the

E8362/3/4C. Adds two 50 dB step attenuators and two bias-tees

to the E8361C. A step attenuator and bias-tee set is inserted

between the source and test port one and another set

between the source and test port two. (see PNA Series

basic block diagram)

□

Add receiver attenuators (Option 016)

An attenuator is added between each test port and its

to the E8362/3/4C. Two 50 dB step attenuators are added to

the E8361C (see PNA Series Microwave Data Sheet literature

number 5989-7605EN for a basic block diagram).

□

High-power test set (Model E836xCH85)

This configuration combines options that are often necessary

for high power measurements (UNL* 3 , 014, 016, 080, 081).

The only difference between ordering Option H85 versus a

combination of the options listed above is the source

attenuator option UNL. Standard UNL includes two source

attenuators and two bias-tees. Option H85 includes the two

source attenuators, but not the bias-tees, as the bias-tees are

maximum power at the test port is +43 dBm (< 20 GHz), and

+40 dBm (> 20 GHz).

1. The E8361C can be extended to 110 GHz with IF access (Option H11).

2. Up to 67 GHz.

3. UNL* does not include bias-tees. Only includes source attenuators

Option 080, frequency-offset mode, is included in Option H85

because it manages the phase-locking internally (instead of

depending on the R1 receiver). So if you need to use external

components in the path of the R1 receiver, it makes the

measurements simpler and more robust.


□

Time-domain capability (Option 010)

For viewing reflection and transmission responses in time or

□

Frequency offset (Option 080) 2

This option enables the PNA Series microwave network analyzers

to set the source frequency independently from where the

receivers are tuned. This ability is important for two general

classes of devices: mixers (and converters) and amplifiers.

Option 080 provides a very basic user interface.

□

Reference receiver switch (Option 081) 2

Option 081 adds a solid-state internal RF transfer switch in the

R1 reference-receiver path (see PNA Series Microwave Data

Sheet literature number 5989-7605EN for a block diagram). The

switch allows the instrument to easily switch between standard

S-parameter (non-frequency-offset) measurements and frequency

offset measurements such as relative phase or absolute group

delay that require an external reference mixer. The user can set

the switch manually or remotely, but it is best used with the

frequency-converter application (Option 083), where it is controlled

automatically during the vector-mixer calibration procedure

and subsequent measurements.

□

Scalar-calibrated converter measurements (Option 082) 2

With a simple setup and calibration, this application provides

the highest accuracy for conversion-loss (or gain) measurements

by combining one-port and power-meter calibrations to remove

mismatch errors. Option 080 required.

□

Vector- and scalar-calibrated converter measurements

083) 2

This converter measurement adds an intuitive and easy-to-use

user interface, advanced calibration choices that provide

exceptional amplitude and phase accuracy, and control of

external signal sources for use as local oscillators. Mixer

calibration techniques include scalar-mixer calibration and

vector-mixer calibration (requires Option 081). Finally, the

frequency-converter application supports all of Agilent’s major

signal source families.

□

Embedded LO Measurements (Option 084)

This option tunes the PNA receivers to the output frequency of

the converter under test, without the need for access to internal

LOs or a common reference signal. For converters with embed-

ded LOs, this option enables measurements of match-corrected

conversion loss/gain (requires Option 082 or 083), and absolute

group delay (requires Option 083).

15


□

4-port measurement application (Option 550) 1

Adds multiport analyzer mode to any PNA network analyzer

with Option 014 configurable test set, which enables full

4-port error correction and measurement capabilities using an

external test set. Only standard measurement class is available

in the multiport analyzer mode.

□

N-port capabilities (Option 551) 1

Adds multiport analyzer mode to any PNA network analyzer

with Option 014 configurable test set, which enables full

N-port error correction and measurement capabilities using

an external test set. Only standard measurement class is

available in the multiport analyzer mode.


□

Pulsed-RF measurement capability (Option H08) 1

Provides software to set up and control pulsed-RF measurements

with point-in-pulse capability. The software sets the coefficient

of the PNA’s digital-IF filter to null out unwanted spectral

components, enables the IF gates provided with IF access

(Option H11), and controls selected Agilent pulse generators.

It can be run on the PNA or an external computer. A “.dll” file

containing the IF-filter algorithms is included for automated

with the Agilent 81110A series pulse generator.

For more detailed information regarding pulsed measurement

capabilities with the microwave PNA refer to the Agilent Web

MW Network Analyzers Configuration Guide for Pulsed

Measurements, literature number 5989-7913EN.

□

IF access (Option H11)

Provides hardware to enable antenna, point-in pulse, and

broadband millimeter-wave measurements to 110 GHz. For

each of the MW PNA’s measurement receivers, IF gates

(enabled with pulsed measurement capability, Option H08) and

external IF inputs are added. In addition, access to the PNA’s

internal RF and LO source is provided for remote mixing

applications. For basic antenna measurements, only Option H11

is necessary. Pulsed antenna applications also require the

pulsed measurement capability (Option H08). Broadband

measurements to 110 GHz, also requires an N5260A

millimeter-wave test set controller.

Note: Use external IF access for up to 20 dB more sensitivity

when making antenna measurements with a remote mixing

configuration. Add Option H08 (Pulsed-RF Measurement

Capability) to enable advanced pulsed measurements. Or

upgrade to a broadband (10 MHz to 110 GHz) VNA system

simply by purchasing an N5260A controller test set with test

heads (Option 110, 120, or 130).

Accessories

□

Rack mount kit without handles (Option 1CM)

Adds a rack mount (5063-9217) and rail kit (E3663AC) for use

□

Rack mount kit with handles (Option 1CP)

Adds a rack mount (5063-9237) 2 and rail kit (E3663AC) for use

with standard supplied handles.

Configuration Details

Selecting the correct mixer-test configuration:

Most mixer or converter test applications require Options 014, 080, and 082 for conversion loss/gain, or Options 014, 080, 081 and

083 for conversion loss/gain and phase/delay measurements. If you want to create and automate your own custom frequencyoffset measurements (for example, intermodulation distortion), you may only need Options 014 and 080. For converters that require input power below -27 dBm, or for devices that have a large amount of LO feedthrough (like an unfi ltered mixer), Option

UNL, which adds source attenuators, is highly recommended.

Besides allowing lower input power levels, these attenuators improve the isolation between the PNA’s internal source and

LO leakage signals, helping to prevent source-unleveled errors.

For devices that put out signals near or above the receiver’s compression levels (which varies between –3 and +5 dBm, depending on the model and frequency), Option 016 is recommended, which adds receiver attenuators. Finally, Option 010, which adds time-domain analysis, is very useful for gating out unwanted, time-delayed responses which often occur when measuring mixers.

1. Up to 67 GHz.

2. The 5063-9237 kit assumes you have the standard handles shipped

with the instrument. If you do not have handles, order a 5063-9224 kit.

16


Simplified test set block diagrams

R1

Reference receiver

Source

Switch/splitter

Reference receiver R2

A

Measurement receivers

B

Port 1

Extended power range and bias-tees (Option UNL)

Port 2

Bias-tee

R1

Reference receiver

Source attenuator

1

Source

Switch

Reference receiver

A


B

R2

Source attenuator

1

Bias-tee

Port 1

1. Source attenuator for E8362/3/4C is 60 dB in 10 dB steps.

Source attenuator for E8361C is 50 dB in 10 dB steps.

Port 2

17


Simplified test set block diagrams – continued

Configurable test set (Option 014)

R1

Reference receiver

Source

Switch


A


B

Port 1 Port 2

Configurable test set with extended power range and bias-tees (Option UNL and 014)

R1

Source attenuator

1

Reference receiver

Source

Switch


Source attenuator

1

Bias-tee

A


B

Bias-tee

Port 1


Source attenuator for E8361C is 50 dB in 10 dB steps.

18

Port 2



Fully optioned, active device or mixer/converter test configuration (Options 014, UNL, 016, 080, 081)

Option 081

Source out

Rcvr R1 in

Source

Switch/splitter/leveler

R1

Reference receiver

Source attenuator 1

10 dB steps

Bias-tee


A

Receiver attenuator 2

B


Source attenuator 1

10 dB steps

Bias-tee

SRC out

Cplr thru

Cplr arm

Rcvr A in

Rcvr B in

Cplr arm

Cplr thru

SRC out

Rcvr R2 in

Source out

1. Source attenuator for E8362/3/4C is 60 dB in 10 dB steps. Source attenuator for

E8361C is 50 dB in 10 dB steps.

2. Receiver attenuator for E8362/3/4C is 35 dB in 5 dB steps. Receiver attenuator for

E8361C is 50 dB in 10 dB steps.

19



High-power configuration (Model E836xCH85)

Option 081

Source out

Rcvr R1 in

Source

+15

R1

Reference receiver

Source attenuator 1

+30 dBm

10 dB steps

Switch/splitter/leveler

+30 dBm

Reference receiver


Source attenuator 1

+30 dBm

10 dB steps

+15

A

+15

B

+40 dBm

+30 dBm

Receiver attenuator 2

+30 dBm +40 dBm

SRC out

Cplr thru

Cplr arm

Rcvr A in

Rcvr B in

Cplr arm

Cplr thru

SRC out

Rcvr R2 in

Source out preamp

Power levels shown on the diagram are damage levels. At a minimum, keep power levels 6 dB below damage level. For optimal performance, keep the power level incident upon the receivers -20 dBm or less. This will keep the receivers out of compression.


2. Receiver attenuator for E8362/3/4C is 35 dB in 5 dB steps.

20



Fully optioned, pulse-RF, antenna, or mm-wave configuration

(Options 014, UNL, 016, 080, 081, H11)

Aux RF out

(2 to 20 GHz)

Aux LO out

(2 to 20 GHz)

Rear

Option 080

Phase-locked loop

8.33 MHz reference

Offset receiver

Offset

LO

Option 081

V tune

YIG source

Multipliers

(1, 2)

Multipliers (1, 2, 4)

LO

Option H11

Option H11 1

IF gate

ADC

External

IF in

Option UNL

R1 R2

Option H11 1

IF gate

ADC

External

IF in

Option UNL

Front

Option 014

External

IF in

ADC

IF gate

Option H11 1

Option UNL

A

Port 1

Option 016

Receiver attenuators

Option 014

B

External

IF in

IF gate

Option H11 1

ADC

Option UNL

Port 2

Option 014

1. Option H11: IF-gate controls and external-IF inputs are accessed on rear panel.

IF gates are enabled with Option H08. External-IF input frequency is 8.33 MHz.

21


N5250C millimeter-wave system

□

N5250C MM PNA system 1 , 10 MHz to 110 GHz, includes:

E8361C MW PNA with the following options:

• Configurable test set – Option 014

• Extended power range and bias-tees –

• Frequency-offset mode – Option 080

• Reference channel switch – Option 081

• IF access – Option H11

N5260A millimeter-wave test set controller with test heads

• 67 to 110 GHz test heads

Additional options available:

• Millimeter-wave modules with bias-tees -

Banded waveguide solution

In order to assemble a banded waveguide solution, the following components are needed:

• Microwave PNA network analyzer (E8361C or E8362/3/4C) with the following options:

• IF access - Option H11

• Configurable test set - Option 014

• Extended power range and bias-tees - Option UNL

• Frequency-offset mode - Option 080

• Reference channel switch - Option 081

• Millimeter-wave test set controller (N5260A)

with no options

• A set of waveguide modules:

• N5256AW15, 50 to 75 GHz

• N5256AW12, 60 to 90 GHz

• N5256AW10, 75 to 110 GHz

• N5256AW08, 90 to 140 GHz

• N5256AW06, 110 to 170 GHz

• N5256AW05, 140 to 220 GHz

• N5256AW03, 220 to 325 GHz

• Millimeter-wave modules with bias-tees and

port 2 attenuator - N5250C Option 018

• Receiver attenuator – Option 016

• Time-domain capability – Option 010

• Pulsed-RF measurement capability – Option H08 2

• Scalar-calibrated converter measurements – Option 082 2

• Frequency converter application – Option 083 2

Factory integration of the N5250C system integrates the E8361C with Option H11 and the N5260A millimeter-wave controller with test heads. On-site installation is included, and the entire system carries a full one-year, on-site warranty (where available).

NOTE: To significantly improve system dynamic range above 220 GHz,

Agilent strongly recommends adding two external synthesizers such as Agilent’s PSG Series signal generators; one for the RF signal, and one for the LO signal.

For more detailed information, see PNA Millimeter-wave Technical

Overview, literature number 5989-7620EN.

Option Descriptions

□

Millimeter-wave modules with bias-tees (N5250C Option 017)

Adds 67 GHz bias-tees to the combiner assembly between the

input to the combiner and the 67 GHz coupler. The bias-tees have

tri-axial connectors for force, sense, and ground. Positioning the

bias-tees close to the DUT greatly improves stability for on-wafer

On-wafer applications

For on-wafer applications, Cascade Microtech 3 provides complete probing systems using the N5250C. These include both new probing systems and upgrades to existing Cascade Microtech products.

Cascade can also provide on-wafer verification and probing system training. Once the N5250C system is verified in coax, Cascade

Microtech will verify the system through its wafer probes.

□

Millimeter-wave modules with bias-tees and port 2

Adds 67 GHz bias-tees to the combiner assembly between the input to the combiner and the 67 GHz coupler. The bias-tees have tri-axial connectors for force, sense, and ground. Positioning the bias-tees close to the DUT greatly improves stability for on-wafer and in-fixture devices. The bias-tees added for this option have a voltage rating of 40 volts and a maximum of 0.5 amps

Additionally, Option 018 adds a 25 dB micrometer attenuator to the port 2 test head.

22


N5250C millimeter-wave system – continued

With Option 017, the signal is routed out of the PNA from the front panel jumpers rather than the ports. Without Option 017, the signal is routed from the front panel ports to the combiner assembly, allowing access to the

PNA’s internal bias-tees.

E8361C with Option H11

Receiver A

Port 1 Port 2

30 in.

76.2 cm

IF1 IF2

LO RF

IF3 IF4

Test set I/O

Receiver B

30 in.

76.2 cm

N5260A with test heads

48 in.

121.9 cm

Test set controller

Optional bias-tees

(Option 017)

67 to 110 GHz waveguide head

Test port 1

Combiner assembly

Test port 2

Combiner assembly

67 to 110 GHz waveguide head

48 in.

121.9 cm

PNA test set block diagram

Simplified receiver block diagram

SMA connectors

LO: 2 to 20 GHz

R1

IF

BNC connectors

R2

IF

A

IF

B

IF

SMA connectors

RF: 2 to 20 GHz

BNC connectors

R1 gate

R2 gate

A gate

B gate

LO distribution to each receiver

To IF multiplexer

(see Figure 5)

To IF multiplexer

(see Figure 5)

RF

LO

(from LO distribution.

See test set block diagram)

External

IF input

IF multiplexer

IF gating

A/D R1

Reference receiver

Reference receiver

R2

50 dB

Bias-tee

Port 1

A

50 dB 50 dB

Option 016 receiver attenuators

50 dB

B

Bias-tee

Port 2

23


Upgrade kits

Upgrade kits for the PNA Series E8361C, E8362C, E8363C,

E8364C, N5250C1

Upgrade kits are available to add options after initial purchase. To order an upgrade kit for the PNA series, order the analyzer’s model number followed by a “U”, then indicate the option to be added

(for example, E8362CU-010). The current configuration and serial number of the instrument to be retrofitted are required as part of the order.

□

Time-domain (Option 010)

□

Configurable test set (Option 014)

Provides six front-panel RF access loops.

Includes installation at an Agilent service center.

□

Receiver attenuators (Option 016)


□

Frequency range upgrade to an E8363C (40 GHz) PNA

Available only for the E8362C. Includes

installation at an Agilent service center.

□


Available only for the E8362C and E8363C.


□


□

4-Port measurement application (Option 550)

(Available for E8361C, E8362C/3C/4C)

□

N-port capabilities (Option 551)

(Available for E8361C, E8362C/3C/4C)

Adds full N-port error correction and measurement

capabilities. Option 014 and external test set required.

□

Extended power range (Option UNL)

Adds a step attenuator and a bias-tee between source and

each test port. Includes installation at an Agilent service center.

□

Pulsed-RF measurement capability (Option H08)

Provides software to set up and control pulsed-RF

measurements using narrowband detection, with point-in-pulse

and pulse-profile capability. User installable.

□

IF access (Option H11)

Provides hardware for antenna, point-in-pulse, and millimeter-

wave measurements. Adds rear-panel RF and LO outputs,

external IF inputs, and IF gates (gates enabled with Option H08).


□

High-power test set (Option H85)

2

Removes bias tees for higher test port power-handling capability.

Options UNL, 014, 016, 080, and 081 are required. Includes

installation at an Agilent Service Center.

Available only for the E8363C and E8364C.


□

Frequency-offset (Option 080)


□

External reference switch (Option 081)


□

Scalar-calibrated converter measurements (Option 082)

User installable. Option 080 required.

□

Frequency converter measurement application (Option 083)

User installable. Option 080 and 081 required.

□

Embedded LO Measurements (Option 084)

Advanced software tuning that provides absolute group delay of

converters with embedded LOs without the need for access to a

common reference signal. The measurement result is the same as

locking the DUT LO to the reference mixer LO. (Options 080

and 083 required) Requires firmware A.07.05 and above plus

1.1 GHz CPU board.

□

A/B to C model upgrades

Order E8361AU-221, E8362BU-221, E8363BU-221, or E8364BU-221

Note:

1.1 GHz CPU is required to upgrade. Please refer to Customer Support Service

Guides for the correct part number http://na.tm.agilent.com/pna/documents.html


□

Perpetual license for built-in performance test software

for Agilent inclusive cal (Option 897)

Adds built-in performance testing and calibration software

for self-maintainers. Requires additional equipment. See

the analyzer’s Service Guide for more information on

□


for standards compliant cal (Option 898)




1. For N5250C upgrades, order upgrade options for E8361CU.

2. Please contact Agilent to order this upgrade.

24

PNA-L Series Network Analyzer



Description For N5230C

Frequency range and test set (Mandatory, choose only one)

Option 020 300 kHz–6 GHz 2-port standard test set

Option 025

Option 120

300 kHz–6 GHz 2-port configurable test set and extended power range

300 kHz–13.5 GHz 2-port standard test set

N5230C-020

N5230C-025

N5230C-120

Option 125

Option 140

Option 145

Option 146

300 kHz–13.5 GHz 2-port configurable test set and extended power range N5230C-125

300 kHz–13.5 GHz 4-port standard test set N5230C-140

300 kHz–13.5 GHz 4-port configurable test set and extended power range N5230C-145

300 kHz–13.5 GHz 4-port configurable test set, extended power range N5230C-146

Option 220

Option 225

Option 240

Option 245

Option 246

Option 420

Option 425

520

525

1

1 and internal second source

10 MHz–20 GHz 2-port standard test set and internal second source

10 MHz–40 GHz 2-port standard test set

N5230C-220

10 MHz–20 GHz 2-port configurable test set and extended power range N5230C-225

300 kHz–20 GHz 4-port standard test set N5230C-240

300 kHz–20 GHz 4-port configurable test set and extended power range N5230C-245

300 kHz–20 GHz 4-port configurable test set, extended power range N5230C-246

N5230C-420


10 MHz–50 GHz 2-port standard test set N5230C-520



Option 010

Option 010

Time domain for 6 GHz model

Time domain for 13.5, 20, 40 or 50 GHz model

Option 080

Option 082

550 2

551

551

2

2

Frequency offset measurements

Scalar-calibrated converter measurements

4-port measurement application

N-port capabilities for 6, 13.5 or 20 GHz model

N-port capabilities for 40 or 50 GHz model

Accessories

Option 1CM

Option 1CP

N4688A

N4689A

Rack mount kit without handles

Rack mount kit with handles

USB CD R/W drive

N5231C-010

N5230C-010

N5230C-080

N5230C-082

N5230C-550

N5231C-551

N5230C-551

N5230C-1CM

N5230C-1CP

N4688A

N4689A


Option 1A7

Option A6J

Option UK6

ISO 17025 compliant calibration

ANSI Z540 compliant calibration

Commercial calibration certificate with test data

Calibration software for self-maintainers

897 3 Perpetual license for built-in performance test software for


898 3 Perpetual license for built-in performance test software for standards compliant calibration

N5230C-1A7

N5230C-A6J

N5230C-UK6

N5230C-897

N5230C-898

Additional information



Option 080 required

Not available on 4-port models.

Requires test set Option xx5 or xx6



1. Not available in all countries

2. Option 550 is a subset of 551; therefore they cannot be ordered together. When ordering a test set, select an option to specify the appropriate



25


The PNA-L is an integrated vector network analyzer equipped with a built-in S-parameter test set, one or two synthesized sources used for device stimulus, a hard disk drive, USB interfaces, and an

8.4” LCD color touch screen display. 40 and 50 GHz models have

2.4 mm ruggedized male 50-ohm connectors, while all other models have 3.5 mm ruggedized male 50-ohm connectors. Included with each instrument is a mouse, keyboard (U.S.) and a 1-year return-to-Agilent service warranty.


• Standard test set and power range (Option xx0)

The 13.5 and 20 GHz versions are available in 2- or 4-ports.

• Configurable test set and extended power range (Option xx5)

Adds front panel access loops and one or two 60 dB step

attenuators as shown in the figures below. This provides the

capability to improve instrument sensitivity for measuring

even more dynamic range or to add components and other

peripheral instruments for a variety of measurement applications.

• Configurable test set, extended power range and internal

second source (Option x46)

Available with 4-port models only, this option adds an internal

second source, nine front panel access loops and two 60 dB

step attenuators as shown in the figure below. This provides an

additional signal (fixed or swept) for two-tone third-order-intercept

(TOI) and intermodulation testing of amplifiers; or it can be used

as a fast swept-LO signal for fixed-IF testing of mixers and

converters. In either case, sweep speed is more than twenty times

faster than using an external source (Option 080 recommended.

Please note, Option 080 is needed in order to have independent

control of the two internal sources.).

2-port standard test set

4-port standard test set

Source

Reference receiver

R

Switch

D

A

PORT 4

PORT 3

PORT 2

PORT 1

4-port configurable test set and extended power range

Source 60 dB

Reference receiver

R

Switch

D

C

B

A

Source out

Coupler thru

PORT 4

Coupler arm

Receiver D in

Source out

Coupler thru

PORT 3

Coupler arm

Receiver C in

Receiver B in

Coupler arm

PORT 2

Coupler thru

Source out

Receiver A in

Coupler arm

PORT 1

Coupler thru

Source out

Source out

Receiver R in

R1

Reference receiver

Source

Switch/splitter


C

B

A


B

4-port configurable test set, extended power range and internal second source

Source 1 Source 2

60 dB 60 dB

Port 1 Port 2

2-port configurable test set and extended power range A

R

B C D

Source out

Rcvr

R1 in

26

SRC out

Cplr thru

60 dB

R1

Reference receiver

Source

Switch/splitter


60 dB

A


B

Port 1 Cplr arm

Rcvr

A in

Rcvr

B in

Cplr arm

Port 2 Cplr thru

SRC out

Rcvr

R2 in

Source out




□

Time domain (Option 010)

This option enables the PNA Series to view reflection and trans-

mission responses in both time or distance domain. Use time

domain to tune filters, gate out the response of fixtures and

cables, characterize the impedance of transmission line, and more.

□

4-port measurement application (Option 550)

Adds multiport analyzer mode to any 2-port PNA-L network

analyzer with configurable test set (Option xx5 or xx6), which

enables full 4-port error correction and measurement capabilities

using an external test set. Only standard measurement class is

available in the multiport analyzer mode.

□

Frequency offset (Option 080)

This option enables the PNA Series to set the source frequency

independently from where the receivers are tuned. This ability

is important for two general classes of devices: mixers (and

converters) and amplifiers.

□

Scalar-calibrated converter measurements (Option 082)

With a simple setup and calibration, this application provides the

highest accuracy for conversion-loss (or gain) measurements by

combining one-port and power-meter calibrations to remove

mismatch errors. Option 080 required.

□

N-port capabilities (Option 551)

Adds multiport analyzer mode to any PNA-L network analyzer

with configurable test set (Options xx5 or xx6), which enables

full N-port error correction and measurement capabilities using

an external test set. Only standard measurement class is avail-

able in the multiport analyzer mode.

27


Upgrade kits

See the analyzer’s Service Guide for more information on

Upgrade kits are available to add options after initial purchase.

To order an upgrade kit for the PNA-L series, order the analyzer’s model number followed by a “U”, then indicate the option to be added (example: N5230CU-010). The serial number of the instrument to be retrofitted is required as part of the order.

□

Time-domain upgrade kit (Option 010)

The serial number of the instrument to be retrofitted must be

specified when ordering this kit. User installable.

□

Frequency-offset upgrade kit (Option 080)

The serial number of the instrument to be retrofitted must be

specified when ordering this kit. User installable.

□

Scalar-calibrated converter measurements (Option 082)

User installable. Option 080 required.

□

4-port measurement application (Option 550)

Enables full 4-port error correction and differential measurements

on a 2-port network analyzer with configurable test set (Option x25).

External test set required. User installable.

□

N-port capabilities (Option 551)

Adds full N-port error correction and measurement capabilities to

PNA-L with configurable test set (Option xx5 or x46). External test

set required. User installable.

□

6 or 13.5 GHz configurable test set & extended power range

□

A to C model upgrade

Order N5230AU-221 for 2-port PNA-L, or N5230AU-241 for

Note:

1.1 GHz CPU is required to upgrade. Please refer to Customer Support Service

Guides for the correct part number http://na.tm.agilent.com/pna/documents.html

□

20 GHz 4-port configurable test set, extended power range &

internal second source upgrade kit (Option 927)

Applicable to 20 GHz 4-port PNA-L (N5230C-245). Upgrade to

configurable test set, extended power range and internal second

source. Includes installation at an Agilent service center.

Option 080 recommended.

□

40 or 50 GHz configurable test set & extended power range

Applicable to 40 or 50 GHz PNA-L (N5230C-420, N5230C-520).

Upgrade to configurable test set and extended power range.


□

Frequency range upgrade from 6 to 13.5 GHz (Option 960)

Applicable to the 6 GHz PNA-L (N5230C-020, N5230C-025).


□

Frequency range upgrade from 13.5 to 20 GHz (Option 966)

Applicable to the 13.5 GHz 4-port PNA-L (N5230C-140,

N5230C-145, N5230C-146). Includes installation at an Agilent

Applicable to 6 or 13.5 GHz PNA-L (N5230C-020, N5230C-120). Upgrade

to configurable test set and extended power range. Includes

□

20 GHz 2-port configurable test set & extended power range

Applicable to 20 GHz PNA-L (N5230C-220) Upgrade to

configurable test set and extended power range. Includes


□

13.5 or 20 GHz 4-port configurable test set & extended power

range upgrade kit (Option 926)

Applicable to 20 GHz 4-port PNA-L (N5230C-140, N5230C-240).

Upgrade to configurable test set and extended power range.


□

13.5 GHz 4-port configurable test set, extended power range &

internal second source upgrade kit (Option 928)

Applicable to 13.5 GHz 4-port PNA-L (N5230C-145). Upgrade to

configurable test set, extended power range and internal second

source. Includes installation at an Agilent service center.

(Option 080 recommended. Please note, Option 080 is needed

in order to have independent control of the two internal sources.)


□


for Agilent inclusive cal (Option 897)




□

Frequency range upgrade from 20 to 40 GHz (Option 971)

Applicable to the 20 GHz PNA-L (N5230C-220). Includes


□


Applicable to the 20 GHz PNA-L (N5230C-225). Includes


□


Applicable to the 40 GHz PNA-L (N5230C-420, N5230C-425).


For additional upgrade paths, contact your Agilent field office.

6 GHz

13.5 GHz x20 x25 x40 x45 x46

020 901

025

960

960

140

125

966

926

145 928

146

966

20 GHz

40 GHz

240

926

225

971

420 941

973

966

245 927

246

50 GHz

990

520 941

525

□


for standards compliant cal (Option 898)


for self-maintainers. Requires additional equipment.

28

PNA-L upgrade path examples.

Measurement Accessories

A complete list of RF and microwave test accessories is available on our Web site: www.agilent.com/find/accessories

Accessories are available in these connector types:

50 ohm Type-N, 3.5 mm, 7 mm, 2.4 mm, 2.92 mm, 1.85 mm, 1.0 mm, and waveguide. Test port cables and a calibration kit should be added for a complete measurement system. A verification kit is used to verify corrected system performance.

Cables and adapter sets

Agilent offers cables in the following types:

• single cables in semi-rigid and flexible

• cable sets in semi-rigid and flexible

There are also adapter sets available that protect the test port and convert the port to the desired connector interface. These kits contain:

• one male adapter

• one female adapter

To attain the best mechanical rigidity for device connection, use a single cable and the appropriate special adapter set. To attain the greatest flexibility for device connection, use a cable set.

Network analyzer test set

Network analyzer test set

Device under test

Test port adapter

Single cable

Cable set

Device under test

Calibration kits

Coaxial measurements

Mechanical calibration kits include standards, such as opens, shorts and loads, which are measured by the network analyzer for increased measurement accuracy.

Electronic calibration (ECal) kits replace mechanical calibration standards with one solid-state calibration module that is controlled by the network analyzer via USB, to present many different impedances to the test ports. A full two-port calibration can be performed quickly with a single connection. This technique reduces operator errors and connector wear and abrasion.

Choose a calibration kit for each connector type to be used.

Economy, includes:

• open standards (male and female)

• short standards (male and female)

• fixed-termination standards (male and female)

Standard, includes the devices in the economy kit and adds:

• sliding load standards (male and female) or a series of

Precision, includes the devices in the economy kit and adds:

• 50 ohm airline(s) for TRL calibration

• TRL adapters

Waveguide measurements

For waveguide measurements, Agilent offers mechanical calibration kits that include:

• waveguide-to-coax adapters (X, P, K, R, Q, U, V)

• precision waveguide section

• flush short circuit

• fixed terminations

• straight section

29

For devices with 1.0 mm connectors

Mechanical calibration/verification kit

□

85059A DC to 110 GHz precision calibration/verification

kit.

Includes:

85059-60003 1.00 mm (m) short 2.450 mm

85059-60007 1.00 mm (f) short 2.450 mm

85059-60004 1.00 mm (m) short 3.000 mm

85059-60008 1.00 mm (f) short 3.000 mm

85059-60002 1.00 mm (m) short 1.825 mm

85059-60006 1.00 mm (f) short 1.825 mm

85059-60001 1.00 mm (m) short 1.300 mm

85059-60005 1.00 mm (f) short 1.300 mm

85059-60009 1.00 mm male open

85059-60010 1.00 mm female open

85059-60019 1.00 mm male load

85059-60020 1.00 mm female load

85059-60021 1.00 mm lossy delay line

11920-60001 1.00 mm (m) to 1.00 mm (m) adapter

11920-60002 1.00 mm (f) to 1.00 mm (f) adapter

11920-60003 1.00 mm (m) to 1.00 mm (f) adapter

11500-60001 1.00 mm (f) to 1.00 mm (f) 8.8 cm cable

85059-60016 1.00 mm mismatch thru adapter

85059-60017 1.00 mm matched thru adapter

8710-2079

8710-2156

6 mm, 4 in-lb torque wrench

6 mm open end wrench

Cables

□

11500I 1.0 mm (f-f) test port cable (8.8 cm)

□

11500J 1.0 mm (m-f) test port cable (16.0 cm) 1

□

11500K 1.0 mm (m-f) test port cable (20.0 cm) 1

□

11500L 1.0 mm (m-f) test port cable (24.0 cm) 1

Adapter set

□

V281C 1.0 mm(f) to V-band waveguide adapter

□

V281D 1.0 mm (m) to V-band waveguide adapter

□

W281C 1.0 mm (f) to W-band waveguide adapter

□

W281D 1.0 mm (m) to W-band waveguide adapter

□

11920A 1.0 mm (m) to 1.0 mm (m) adapter

□

11920B 1.0 mm (f) to 1.0 mm (f) adapter

□

11920C 1.0 mm (m) to 1.0 mm (f) adapter

□


□


□


□

11921D 1.0 mm (f) to 1.85 mm (m) adapter

□


□


□


□

11922D 1.0 mm (f) to 2.4 mm (m) adapter

□

11923A 1.0 mm (f) connector launch assembly

1. For on-wafer applications, two 11500J/K/L cables are required;

one cable for each test port.

2. Special rugged female connector specifically for connecting to the

network analyzer test port, but does not mate with a standard

30


Mechanical calibration kits

□

85058B standard: DC to 67 GHz.

Includes:

85058-60101 1.85 mm (m) short 5.4 mm

85058-60102 1.85 mm (m) short 6.3 mm

85058-60103 1.85 mm (m) short 7.12 mm

85058-60104 1.85 mm (m) short 7.6 mm

85058-60105 1.85 mm (f) short 5.4 mm

85058-60106 1.85 mm (f) short 6.3 mm

85058-60107 1.85 mm (f) short 7.12 mm

85058-60108 1.85 mm (f) short 7.6 mm

85058-60109 1.85 mm male open

85058-60110 1.85 mm female open

85058-60111 1.85 mm male load

85058-60112 1.85 mm female load




□

85058E economy: DC to 67 GHz.

Includes:

85058-60101 1.85 mm (m) short 5.4 mm

85058-60105 1.85 mm (f) short 5.4 mm

85058-60109 1.85 mm male open

85058-60110 1.85 mm female open

85058-60123 1.85 mm male load

85058-60124 1.85 mm female load




Electronic calibration kits

□

N4694A Microwave ECal: 10 MHz to 67 GHz, 2-ports.

Includes:

N4694-60001 1.85 mm (f) to 1.85 mm (m) ECal module

N4694-60002 1.85 mm (m) to 1.85 mm (m) ECal module

N4694-60003 1.85 mm (f) to 1.85 mm (f) ECal module



Cables

□

N4697E 2 Single, flexible: 1.85 mm (f) to 1.85 mm (f),

96.5 cm, 38 inches

□

N4697F 2 Set, flexible:

One 1.85 mm (f) to 1.85 mm (f) cable, 62.2 cm,

24.5 inches, p/n N4697-60100

One 1.85 mm (f) to 1.85 mm (m) cable, 62.2 cm,

24.5 inches, p/n N4697-60200

□

N4697H 2 Single, flexible: 1.85 mm (f) to

1.85 mm (m), 62.2 cm, 24.5 inches

□

N4421B-B67 Set of 4, flexible: 1.85 mm (f) to

1.85 mm (m), 91.4 cm, 36 inches

Adapter set

□

85130H 1.85 mm 2 to 1.85 mm



□

85056A standard: DC to 50 GHz.

Includes:

00901-60003 2.4 mm (m) fixed broadband load

00902-60004 2.4 mm (f) fixed broadband load

00915-60003 2.4 mm (m) sliding load

00915-60004 2.4 mm (f) sliding load




85056-60020 2.4 mm (m) short

85056-60021 2.4 mm (f) short

85056-60022 2.4 mm (m) open

85056-60023 2.4 mm (f) open

□

85056D economy: DC to 50 GHz.

Includes:

00901-60003 2.4 mm (m) fixed broadband load

00902-60004 2.4 mm (f) fixed broadband load




85056-60020 2.4 mm (m) short

85056-60021 2.4 mm (f) short

85056-60022 2.4 mm (m) open

85056-60023 2.4 mm (f) open


□


Includes:






Cables

Note: Agilent offers the following 2.4 mm test port cables. Adapters will be necessary when using these cables for 2.92 mm measurements.

□

85133C 1 single, semi-rigid: 2.4 mm (f) to PSC-2.4 mm (f),

81 cm, 32 inches

□

85133D 1 set, semi-rigid:

One 2.4 mm (f) to 2.4 mm (m), 53 cm, 21 inches,

One 2.4 mm (f) to 2.4 mm (f), 53 cm, 21 inches,

□

85133E 1 single, flexible: 2.4 mm (f) to PSC-2.4 mm (f),

97 cm, 38 inches

□

85133F 1 set, flexible:



□

85133G 1 Single, semi-rigid: 2.4 mm (f) to 2.4 mm (m),

53 cm, 21 inches

□

85133H 1 Single, flexible: 2.4 mm (f) to 2.4 mm (m),

63 cm, 25 inches

□

N4421A-B20 Set of 4, flexible: 2.4 mm (f) to 2.4 mm (m),

91.4 cm, 36 inches

1. Special rugged female connector specifically for connecting to the network analyzer test port, but does not mate with a standard male connector.

2. Special rugged female connector specifically for connecting to the network analyzers NMD 2.4 mm test port, but does not mate with standard 2.4 mm male connector

Adapter set

□

85130F 2.4 mm 1 to 3.5 mm

□

85130F 2.5 mm 1 to 3.5 mm

□

85130G 2.4 mm 1 to 2.4 mm

For devices with K connectors (2.92 mm)


□

85056KE01 DC to 40 GHz

For use with user supplied 2.9 mm test port cables. 2.92 mm

(K connector) calibration kit with fixed and sliding loads. The

Agilent 85056KE01 calibration kit is an ordering convenience to allow the pass through ordering from Agilent Technologies,

Inc. for the Maury 8770C47 calibration kit.

□

85056KE02 DC to 40 GHz

For use with user supplied 2.92 mm test ports cables. 2.92 mm

(K connector) calibration kit with fixed loads only. The Agilent

85056KE02 calibration kit is an ordering convenience to allow the pass through ordering from Agilent Technologies, Inc. for the Maury 8770D47 calibration kit.

The 85056KE01 and 85056KE02 contains one NMD 2.4 mm

2

(f) to 2.92 mm (f) and one NMD 2.4 mm 2 (f) to 2.92 mm (m) test port adapter to adapt the 2.4 mm test ports of the PNA to 2.92 mm. It also supplies 2.92 mm to 2.92 mm in-series adapters (3 adapters) and a PNA Cal Coefficients on a USB stick. Users must supply their own 2.92 mm or K-connector test port cables. Also included is a 2.92 mm torque wrench.

Maury Microwave Terms and Conditions for Warranty and

Return apply. Maury Microwave Corp. calibration kits are to be returned directly to Maury Microwave for service, repair, or calibration issues and not to Agilent Technologies. For additional information go to www.maurymicrowave.com.

Agilent Technologies does not guarantee the performance of the Maury calibration kits or the system performance when connected to Agilent Microwave PNA Series network analyzers.


□


Includes:




N4692-60021 2.92 mm (m) to 2.92 mm (m) adapter

N4692-60022 2.92 mm (f) to 2.92 mm (f) adapter

31

Cables

Note: Agilent offers the following 2.4 mm test port cables. Adapters will be necessary when using these cables for 2.92 mm measurements.

□


81 cm, 32 inches

□




□


97 cm, 38 inches

□




□

85133G 1 Single, semi-rigid: 2.4 mm (f) to 2.4 mm (m),

53 cm, 21 inches

□

85133H 1 Single, flexible: 2.4 mm (f) to 2.4 mm (m),

63 cm, 25 inches

□

N4421A-B20 Set of 4, flexible: 2.4 mm (f) to 2.4 mm (m),

91.4 cm, 36 inches

Adapters

□

11904A 2.4 mm (m) to 2.92 mm (m)

□

11904B 2.4 mm (f) to 2.92 mm (f)

□

11904C 2.4 mm (m) to 2.92 mm (f)

□

11904D 2.4 mm (f) to 2.92 mm (m)

□

11904S 2.4 mm to 2.92 mm

Adapter set, contains 4 matched adapters

1. Special rugged female connector specifically for connecting to the network analyzer test port, but does not mate with a standard male connector.

32

For devices with 3.5 mm or SMA connectors


□

85052B standard: DC to 26.5 GHz.

Includes:

00902-60003 3.5 mm (m) fixed load

00902-60004 3.5 mm (f) fixed load

00911-60019 3.5 mm (m) sliding load

00911-60020 3.5 mm (f) sliding load

85052-60006 3.5 mm (m) short

85052-60007 3.5 mm (f) short

85052-60008 3.5 mm (m) open

85052-60009 3.5 mm (f) open


85052-60013 3.5 mm (f) to 3.5 mm (m) adapter


□

85052C precision TRL: DC to 26.5 GHz.

Includes:

00902-60003 3.5 mm (m) fixed load

00902-60004 3.5 mm (f) fixed load

85052-60006 3.5 mm (m) short

85052-60007 3.5 mm (f) short

85052-60008 3.5 mm (m) open

85052-60009 3.5 mm (f) open




85052-60035 3.5 mm short TRL line

85052-60036 3.5 mm long TRL line

□

85052D economy: DC to 26.5 GHz.

Includes:

00902-60003 3.5 mm (m) fixed load

00902-60004 3.5 mm (f) fixed load

85052-60006 3.5 mm (m) short

85052-60007 3.5 mm (f) short

85052-60008 3.5 mm (m) open

85052-60009 3.5 mm (f) open





□

85093C RF ECal: 300 kHz to 9 GHz, 2-ports

Option M0F with:

85093-60008 3.5 mm (f) to 3.5 mm (m) ECal module

Option 00F module with:

85093-60010 3.5 mm (f) to 3.5 mm (f) ECal module

Option 00M module with:

85093-60009 3.5 mm (m) to 3.5 mm (m) ECal module

Option 00A adds:





2. For use with E8362C.

85093C-xxx mixed-connector options:

Port A option Port B option

3.5 mm 101 102 Type-N 203 204 7-16 205 206

□

N4431B Microwave ECal: 300 kHz to 13.5 GHz, 4-ports.

Includes:

Option 010 module with:

N4431-60006 4 x 3.5 mm (f) ECal module

N4431B-xxx mixed-connector options:

Connector Port A Port B Port C Port D

3.5 mm (f)

3.5 mm (m)

101

102

Type-N 50 ohm (f) 103

Type-N 50 ohm (m) 104

7-16 (f)

7-16 (m)

105

106

201

202

203

204

205

206

301

302

303

304

305

306

□

N4433A Microwave ECal: 300 kHz to 20 GHz, 4-ports.

Includes:

□


N4433-60003 4 x 3.5 mm (f) ECal module

401

402

403

404

405

406

N4433A-xxx mixed-connector options:


3.5 mm (f)

3.5 mm (m)

101

102

201

202

301

302

401

402

□


Includes:

Option M0F module with:






Cables

□


81 cm, 32 inches 2

□



One 3.5 mm (f) to PSC-3.5 mm (f), 53 cm, 21 inches,

□


96.5 cm, 38 inches 2

□


One 3.5 mm (f) to 3.5 mm (m), 62.2 cm, 24.5 inches,

One 3.5 mm (f) to PSC-3.5 mm (f), 62.2 cm, 24.5 inches,

33

□

85131G 1 single, semi-rigid: 3.5 mm (f) to 3.5 mm (m),

53 cm, 21 inches

□

85131H 1 single, flexible: 3.5 mm (f) to 3.5 mm (m),

62.2 cm, 24.5 inches

□

85134C 1 single, semi-rigid: PSC-3.5 mm (f) to 2.4 mm (f),

81 cm, 32 inches

□



One 2.4 mm (f) to PSC-3.5 mm (m), 53 cm, 21 inches,

□

85134E 1 single, flexible: PSC-3.5 mm (f) to 2.4 mm (f),

96 cm, 38 inches

□



One 2.4 mm (f) to PSC-3.5 mm (m), 53 cm, 21 inches,

□

85134G 1 single, semi-rigid: 2.4 mm (f) to PSC-3.5 mm (m),

53 cm, 21 inches

□

85134H 1 single, flexible: 2.4 mm (f) to PSC-3.5 mm (m),

53 cm, 21 inches

□

N4419A-B20 set of 4, flexible: 3.5 mm (m) to 3.5 mm (f),

91.4 cm, 36 inches

□

Z5623A-B20 set of 4, flexible: 3.5 mm (m) to 3.5 mm (m),

91.4 cm, 36 inches (phase-matched)

Adapter sets

□

85130D 3.5 mm 1 to 3.5 mm

For devices with Type-N connectors


□


Includes:

00909-60011 Type-N (m) fixed lowband load

00909-60012 Type-N (f) fixed lowband load

85054-60025 Type-N (m) short

85054-60026 Type-N (f) short

85054-60027 Type-N (m) open

85054-60028 Type-N (f) open

85054-60031 Type-N (f) to 7mm adapter

85054-60032 Type-N (m) to 7mm adapter

85054-60037 Type-N (f) to Type-N (f) adapter

85054-60038 Type-N (m) to Type-N (m) adapter

85054-80010 Type-N (f) sliding load

85054-80009 Type-N (m) sliding load

85054-60050 Type-N (f) connector gage

85054-60052 Type-N (f) gage master

85054-60051 Type-N (m) connector gage

85054-60053 Type-N (m) gage master

□


Includes:

85054-60025 Type-N (m) short

85054-60026 Type-N (f) short




34

85054-60027 Type-N (m) open

85054-60028 Type-N (f) open

85054-60031 Type-N (f) to 7mm adapter

85054-60032 Type-N (m) to 7mm adapter



85054-60046 Type-N (m) fixed load

85054-60047 Type-N (f) fixed load

Adapter sets

□

85130C 3.5 mm 2 to Type-N


□


Includes:


N4431-60007 4 x Type-N (f) ECal module

N4431B-xxx mixed-connector options:


3.5 mm (f)

3.5 mm (m)

101

102

201

202

Type-N 50 ohm (f) 103 203


7-16 (f)

1

204

7-16 (m)

1

106

301

302

303

304

□

N4432A Microwave ECal: 300 kHz to 18 GHz, 4-ports.

Includes:


N4432-60003 4 x Type-N (f) ECal module

401

402

403

404

N4432A-xxx mixed-connector options:


3.5 mm (f)

3.5 mm (m)

101

102

Type-N 50 ohm (f) 103


201

202

203

204

301

302

303

304

401

402

403

404

□

N4690B Microwave ECal: 300 kHz to 18 GHz, 2-ports.

Includes:

N4690-60001 Type-N (f) to Type-N (m) ECal module

N4690-60002 Type-N (m) to Type-N (m) ECal module

N4690-60003 Type-N (f) to Type-N (f) ECal module



Cables 2

Use the test port cables recommended for devices with 7 mm connectors, and 7 mm to Type-N adapters that are from the

85054B/D Type-N calibration kit (see 7 mm connector section).

For devices with 7 mm connectors


□


Includes:

00909-60008 7 mm coax termination

85050-60006 7 mm fixed broadband load

85050-80007 7 mm short

85050-80010 7 mm open

85050-80011 7 mm sliding load

□

85050C precision TRL: DC to 18 GHz.

Includes:

00909-60008 7 mm coax termination

85050-60003 7 mm to 7 mm airline

85050-60005 7 mm to 7 mm TRL adapter


85050-80008 7 mm short

85050-80009 7 mm short collet

85050-80010 7 mm open

□


Includes:


85050-80007 7 mm short

85050-80010 7 mm open


□

N4696B Microwave ECal: 300 kHz to 18 GHz, 2-ports,

7mm to 7mm Microwave module

Cables 1

□

85132C single, semi-rigid: 7 mm to 3.5 mm (f),

81 cm, 32 inches 2

□

85132D set, semi-rigid: two 3.5 mm (f) to 7 mm cables,

53 cm each, 21 inches each 2 , p/n 85132-60003

□

85132E single, flexible: 7 mm to 3.5 mm (f),

97.2 cm, 38.25 inches 2

□

85132F set, flexible: two 3.5 mm (f) to 7 mm cables,

62.9 cm each, 24.75 inches each 2 , p/n 85132-60004

□

85135C single, semi-rigid: 7 mm to 2.4 mm (f),

81 cm, 32 inches

□

85135D set, semi-rigid: two 2.4 mm (f) to 7 mm cables,

53 cm each, 21 inches each, p/n 85135-60001

□

85135E single, flexible: 7 mm to 2.4 mm (f),

96 cm, 38 inches

□

85135F set, flexible: two 2.4 mm (f) to 7 mm cables,

53 cm each, 21 inches each, p/n 85135-60002

Adapter sets

□

85130E 2.4 mm 1 to 7 mm




For devices with waveguide


X Band

□

X11644A standard, WR-90: 8.2 to 12.4 GHz. Includes:

00896-60008 X-band standard section

00910-60003 X-band termination

11644-20018 X-band short

11644-20021 X-band shim

□

85132F cable set (set, flexible 7 mm to 3.5 mm,

62.9 cm each, 24.75 inches each 2 )

□

85135F cable set (set, flexible,

7 mm to 2.4 mm, 53 cm each, 21 inches each)

□

X281C adapter (included in calibration kit):

WR-90 to 7 mm

P Band

□

P11644A standard, WR-62: 12.4 to 18 GHz.

Includes:

00896-60007 P-band standard section

00910-60002 P-band termination

11644-20017 P-band short

11644-20020 P-band shim

□

85132F cable set (set, flexible, 7 mm to 3.5 mm,

62.9 cm each, 24.75 inches each 2 )

□

85135F cable set (set, flexible, 7 mm to 2.4 mm,

53 cm each, 21 inches each)

□

P281C adapter (included in calibration kit):

WR-62 to 7 mm

K Band

□

K11644A standard, WR-42: 18 to 26.5 GHz.

Includes:

00896-60006 K-band standard section

00910-60001 K-band termination

11644-20016 K-band short

11644-20019 K-band shim

□

85134F cable set (set, flexible, 3.5 mm to 2.4 mm,

53 cm each, 21 inches each)

□

K281C adapter (included in calibration kit):

WR-42 to 3.5 mm (f)

Option 012 WR-42 to 3.5 mm (m)

R Band

□

R11644A standard, WR-28: 26.5 to 40 GHz.

Includes:

00914-20028 R-band termination

11644-20005 R-band short

11644-20003 R-band shim

11644-60001 R-band 10 cm straight waveguide

11644-60016 R-band 5 cm straight waveguide

□

85133F cable set (set, flexible, 2.4 mm, 53 cm each,

21 inches each)

□

R281A adapter (2.4 mm (f) to WR-28 waveguide

adapter)

□

R281B adapter (2.4 mm (m) to WR-28 waveguide

adapter)

35

Q Band

□

Q11644A standard, WR-22: 33 to 50 GHz.

Includes:

11644-60005 Q-band termination

11644-20004 Q-band short

11644-20001 Q-band shim

11644-60002 Q-band 10 cm straight waveguide

11644-60017 Q-band 5 cm straight waveguide

□

85133F cable set (set, flexible, 2.4 mm, 53 cm each,

21 inches each)

□

Q281A adapter (2.4 mm (f) to WR-22 waveguide adapter)

□

Q281B adapter (2.4 mm (m) to WR-22 waveguide adapter)

U Band

□

U11644A standard, WR-19: 40 to 60 GHz.

Includes:

11644-60006 U-band termination

11644-20004 U-band short

11644-20002 U-band shim

11644-60003 U-band 10 cm straight waveguide

11644-60018 U-band 5 cm straight waveguide

V Band

□

V11644A standard, WR-15: 50 to 75 GHz.

Includes:

11644-60025 V-band termination

11644-20015 V-band short

11644-20013 V-band shim

11644-60012 V-band standard section

Verification kits

All Agilent verification kits include:

• precision Z

0

airline or match thru

• mismatched airline or mismatch thru

• fixed attenuators

• traceable measured data and uncertainties

□

85053B 300 kHz to 26.5 GHz 3.5 mm kit

Includes attenuators, airline and mismatch airline with data on

a 3.5-inch disk for use in confirming accuracy enhanced system

Test procedure is provided in the service manual.

□

85055A 300 kHz to 18 GHz Type-N kit




□

85057B 45 MHz to 50 GHz 2.4 mm kit




□

85058V 45 MHz to 67 GHz 1.85 mm kit

Includes attenuators, match thru and mismatch thru with data

on a 3.5-inch disk for use in confirming accuracy enhanced

system measurement performance, traceable to national

standards. Test procedure is provided in the service manual.

36

General Accessories

USB

□

N4688A CD-ROM drive

Provides an external read/write CD-ROM drive with a USB cable.

□

N4689A USB hub

Provides a USB hub for connecting additional USB peripherals.

Hard drive

1

□

N8981A spare hard drive with mounting cradle

For E836xA/B and N5230A.

□

N8982A spare hard drive with mounting cradle

For E836xC and N5230C.

□

N5242-60035 spare hard drive

For N5242A with 1.6 GHz Pentium M CPU.

□

N5242-60037 spare CPU board with hard drive

For N5242A with 1.6 GHz Pentium M CPU.

□

N5242-60044 spare hard drive with mounting cradle

For N524xA with 2.0 GHz Core 2 Duo CPU.

Probe

□

85024A high-frequency probe

Provides high-impedance in-circuit test capability from

300 kHz to 3 GHz.

Power meters and sensors

2

Recommended for self support, adjustments and performance tests to verify proper instrument operation.

□

U2000A USB power sensor, 10 MHz to 18 GHz

□


□


□

U2004A USB power sensor, 9 kHz to 6 GHz

□

E4418B single-channel power meter

□

E4419B dual-channel power meter

□

8481B power sensor, 10 MHz to 18 GHz, Type-N (m), 25 W

□

8481A power sensor, 10 MHz to 18 GHz, Type-N (m), 100 mW

□

8485A power sensor, 50 MHz to 26.5 GHz, APC-3.5 mm (m),

□

8487A power sensor, 50 MHz to 50 GHz, 2.4 mm, 300 mW

□

8487D power sensor, 50 MHz to 50 GHz, 2.4 mm, 100 mW

□

R8486A power sensor, 26 GHz to 40 GHz, waveguide flange

UG-599/U, 100 mW

□

Q8486A power sensor, 33 GHz to 50 GHz, waveguide flange

UG-383/U, 100 mW

□

U8486A power sensor, 50 GHz to 75 GHz, waveguide flange

UG-385/U, 200 mW avg

□

E4412A CW power sensor, 10 MHz to 18 GHz, Type-N (m), 200 mW

□

E4413A CW power sensor, 50 MHz to 26.5 GHz, 3.5 mm, 200 mW

Amplifiers

□

83006A power amplifier, 10 MHz to 26.5 GHz, 20 dB gain,

power out: +18 dBm to 10 GHz or +16 dBm to 20 GHz or

+14 dBm to 26.5 GHz

□

83017A power amplifier, 50 MHz to 26.5 GHz, 25 dB gain,

power out: +20 dBm to 20 GHz, or +15 dBm to 26.5 GHz

□

83018A power amplifier, 2 to 26.5 GHz, 27 dB gain to 20 GHz

or 23 dB to 26.5 GHz, power out: +24 dBm to 20 GHz or

+21 dBm to 26.5 GHz

□

83020A power amplifier, 2 to 26.5 GHz, 30 dB gain to 20 GHz

or 27 dB to 26.5 GHz, power out: +30 dBm to 20 GHz or

+26 dBm to 26.5 GHz

□

83050A power amplifier, 2 to 50 GHz, 23 dB gain, power out:

+20 dBm to 40 GHz or +17 dBm to 50 GHz

□

83051A power amplifier, 45 MHz to 50 GHz, 23 dB gain power out:

+12 dBm to 45 GHz or +10 dBm to 50 GHz

Couplers

□

87300B coaxial coupler, 1 to 20 GHz, SMA (f), 10 dB coupling

□

87300C coaxial coupler, 1 to 26.5 GHz, 3.5 mm (f), 10 dB coupling

□

87301B coaxial coupler, 10 to 46 GHz, 2.92 mm (f), 10 dB coupling

□

87301D coaxial coupler, 1 to 40 GHz, 2.4 mm (f) or optional

2.92 mm (f), 13 dB coupling

□

87301E coaxial coupler, 2 to 50 GHz, 2.4 mm (f), 10 dB coupling

□

87310B 90 o coaxial coupler, 1 to 18 GHz, SMA (f), 3 dB coupling

Equipment rack accessories

□

E3663AC Rail kit

□

5063-9217 Rack mount kit, for use without handles

(included with Option 1CM)

□

5063-9205 Front handle kit

3

□

5063-9224 Rack mount kit with handles

3

□

5063-9237 Rack mount kit, for use with standard supplied

handles (included with Option 1CP)

3

Monitors

VGA-compatible monitor

Printers

USB, LAN, parallel or serial printers with Microsoft® Windows® printer driver

Interface cables

Choose the appropriate cables to connect each peripheral to the network analyzer.

□

10833A GPIB cable, 1.0 m (3.3 ft)

□

10833B GPIB cable, 2.0 m (6.6 ft)

□

10833D GPIB cable, 0.5 m (1.6 ft)

□

82357B GPIB to USB interface

1. For more information on hard drive, refer to na.tm.agilent.com/pna/

hdnumbers.html

2. For the latest guide to power meters and power sensors, refer to the

Agilent web site: www.agilent.com/find/powermeters

3. Front handles and Option 1CP (rack mount with handles) are not

available for the N5242A.

37

Applications

Material measurements

□

85070E High-Temperature Dielectric Probe Kit

The 85070E enables measurements of the dielectric properties

of materials quickly and conveniently. Measurements made

with this probe are nondestructive and require no sample

preparation. The dielectric probe is well suited for measurements

of liquid, semisolid and flat solid materials. Measurement can be viewed in a variety of formats (ε’ r

, ε” r

, tan δ

or Cole-Cole). The supplied software can be run in the PNA

analyzer or on a PC.

□

85071E Materials Measurement Software

The 85071E materials measurement software calculates the

permittivity and permeability of material samples placed in a

coaxial airline or a rectangular waveguide. The measurement

technique works well for solid materials that can be machined

to fit precisely inside a transmission line. Measurement

results can be viewed in a variety of formats (ε’ r

, ε r

, µ’ r

, µ” r

, tan δ,

or Cole-Cole µ). The software can be run in the PNA analyzer

or on a PC.

Pulsed measurements

1

The pulsed RF measurement capability (Option H08) and IF access

(Option H11), are recommended for pulsed measurements with the PNA Series.

Pulse/pattern generators

Recommended to provide pulse signals and timing to the pulsed

S-parameter text set and MW PNA

□

81104A Pulse/pattern generator, 80 MHz, single-/dual-channel

with one or two Agilent 81105A output modules.

□

81110A Pulse/pattern generator, 165 MHz, single-/dual-channel

with one or two Agilent 81111A output modules.

Note: Each pulse/pattern generator must be ordered with its

configuration.

□

Z5623AH84 Pulsed S-parameter test set, 2 to 40 GHz

Includes two pin switches for bi-directional (forward and

reverse) pulsed-RF stimulus, and two directional couplers for

the reference channels. It does not include internal amplifiers,

but has front panel access loops for switching in external

amplifiers to boost port power in both directions.

□


Includes one pin switch to modulate the analyzer’s

internal source in the forward direction, and one directional

coupler for the reference channel. It does not include internal

amplifiers, but has front panel access loops for switching in

an external amplifier to boost port power.

□


Includes two pin switches for bi-directional (forward and

reverse) pulsed-RF stimulus. It does not include internal amplifiers,

but has front panel access loops for switching in external

amplifiers to boost port power in both directions.

1. For more details regarding pulsed measurement configurations with the

PNA Series, refer to Agilent’s Web site (www.agilent.com/find/pna)

to download a copy of the Microwave PNA Series Network Analyzer

Configuration Guide for Pulsed Measurements, literature number 5989-7913EN.

38

Agilent Email Updates

www.agilent.com/find/emailupdates

Get the latest information on the products and applications you select. www.lxistandard.org

LXI is the LAN-based successor to GPIB, providing faster, more efficient connectivity. Agilent is a founding member of the

LXI consortium.

Agilent Channel Partners

www.agilent.com/find/channelpartners

Get the best of both worlds: Agilent’s measurement expertise and product breadth, combined with channel partner convenience.

Expand your measurement capabilities with Agilent qualified channel partners

Our channel partners offer accessories and measurement solutions that extend your network analysis capabilities.

For more information about probing equipment and accessories, contact:

Cascade Microtech, Inc

2430 NW 206th Avenue

Beaverton, Oregon 97006, USA

Toll free telephone: 1-800-550-3279

Telephone: (503) 601-1000

Fax: (503) 601-1002

Web site: www.cascademicrotech.com

E-mail: [email protected]

www.agilent.com

Remove

all

doubt

Our repair and calibration services will get your equipment back to you, performing like new, when promised. You will get full value out of your Agilent equipment throughout its lifetime. Your equipment will be serviced by Agilent-trained technicians using the latest factory calibration procedures, automated repair diagnostics and genuine parts.

You will always have the utmost confidence in your measurements.

For information regarding self maintenance of this product, please contact your Agilent office.

Agilent offers a wide range of additional expert test and measurement services for your equipment, including initial start-up assistance, onsite education and training, as well as design, system integration, and project management.

For more information on Agilent Technologies’ products, applications or services, please contact your local Agilent office.

The complete list is available at:

www.agilent.com/find/contactus

Americas

Latin America 305 269 7500

United States (800) 829-4444

Asia Pacific

Australia

China

Hong Kong

India

Japan

Korea

Malaysia

Singapore

Taiwan

Thailand

1 800 629 485

800 810 0189

800 938 693

1 800 112 929

0120 (421) 345

080 769 0800

1 800 888 848

1 800 375 8100

0800 047 866

1 800 226 008

For more information on repair and calibration services, go to:

www.agilent.com/find/removealldoubt

Europe & Middle East

Austria 43 (0) 1 360 277 1571

Belgium

Denmark

32 (0) 2 404 93 40

45 70 13 15 15

Finland

France

358 (0) 10 855 2100

0825 010 700*

Product specifications and descriptions in this document subject to change without notice.

Germany

Ireland

Israel

Italy

Netherlands

49 (0) 7031 464 6333

1890 924 204

972-3-9288-504/544

39 02 92 60 8484

31 (0) 20 547 2111

Spain

Sweden

34 (91) 631 3300

0200-88 22 55

Switzerland 0800 80 53 53

United Kingdom 44 (0) 118 9276201

Other European Countries: www.agilent.com/find/contactus

Revised: October 1, 2009

© Agilent Technologies, Inc. 2009, 2010

Printed in USA, April 19, 2010

5989-7606EN

Pentium ® is a U.S. registered trademark of Intel Corporation.

Microsoft ® and Windows ® are registered trademarks of Microsoft Corporation.

Agilent Technologies E8364C Specifications

Configuration Guide

This configuration guide describes standard configurations, options, accessories, upgrade kits and compatible peripherals for the PNA family microwave network analyzers. This guide should be used with the Agilent PNA family data sheets for a complete description of these analyzers.

Option configurations

Option configurations (continued)

Test set and power configuration options

Measurement applications

Measurement applications

(continued)

PNA-X Noise Figure Options Summary

Nonlinear vector network analysis

Pulse, antenna, mm-wave

Accessories

Upgrade kits

Upgrade kits are available to add options after initial purchase. To upgrade the PNA-X, order the corresponding item number.

The model and serial numbers of the instrument to be retrofitted are required as part of the order.

Upgrade kits (continued)

Upgrade kits are available to add options after initial purchase. To upgrade the PNA-X, order the corresponding item number.

The model and serial numbers of the instrument to be retrofitted are required as part of the order.

Frequency

13.5 GHz

N5241AU-960

26.5 GHz

43.5 GHz

N5244A-990

50 GHz

PNA-X upgrade path

2-port 4-port

944

942

200

921

940

922

224 219

219

029

924

922

224

029

924

400

926

419

927

929

419

029

927

423

929

423

029

H85

H85

Option configurations

Test set and power configuration options

Measurement applications

Pulse, antenna, mm-wave

Accessories

Configuration Details

Selecting the correct mixer-test configuration:

Simplified test set block diagrams

R1

Reference receiver

Source

Switch/splitter

Reference receiver R2

A

Measurement receivers

B

Port 1

Extended power range and bias-tees (Option UNL)

Port 2

Bias-tee

R1

Reference receiver

Source attenuator

Source