visidec

freestanding quad

Installation Instructions

Important Notes l Each Donut Clamp Assembly supports a maximum weight of 11.5kg (25lbs) l This product suits VESA compliant displays with 75mm x 75mm (3” x 3”) and

100mm x 100mm (4” x 4”) mounting hole patterns.

l The manufacturer does not accept responsibility for incorrect installation

Component Checklist

Check you have received all parts against this component checklist prior to installation

Bits Box

Upright Pole

Donut

Clamp (x4)

Horizontal

Support Donut(x1)

A Attach Upright Pole to Base

Attach the Upright Pole to the Base as shown below. Ensure the Cable

Slot faces towards the rear.

Base

M8x50mm

Screw

(x1)

2.5mm Allen

Key (x1)

Cable

Ball (x8)

5mm Allen

Key (x1)

Cable

Clip (x4)

Extension

Clip (x16)

Mounting Screws

M4x10mm (x16)

M4x12mm (x16)

M4x16mm (x16)

TOOLS REQUIRED: l Phillips Head Screw Driver

B Install Horizontal Support and Donut Clamp

Follow steps below to attach the Horizontal Support and Donut Clamp assembly onto the Upright Pole. Ensure the Cable Slots in all the Poles are facing to the rear.

B.2.

Slide the Horizontal Support to desired position

B.1.

Loosen the Hex screws in the

Horizontal Support Donut using the supplied 5mm Allen Key

LOOSEN

LOOSEN

Back

Upright Pole

Cable Slot

User

POSITION

Cable

Slot

IMPORTANT:

When tightening the Donut Clamp, each of the Donut bolts must be tightened evenly, as failure to do so will damage the Donut Clamp. Do not over-tighten as this may also result in damage.

TIGHTEN

B.3.

Tighten supports firmly using the supplied 5mm

Allen Key

TIGHTEN

TIGHTEN

FIRMLY

M8x50mm Screw

5mm Allen Key

Repeat steps B.1, B.2 and B.3 for the 2nd set of Horizontal

Support and Donut Clamp

C Adjust Donut Clamps

Follow steps below to adjust the position of Donut Clamps. Ensure the Cable Slots in all the Poles are facing to the rear.

C.1.

Loosen Donut Bolts evenly using the supplied 5mm

Allen Key

C.2.

Slide the Donut Clamp to desired position

C.3.

Tighten Donut Bolts firmly using the supplied 5mm

Allen Key

IMPORTANT:

When tightening the Donut

Clamp, each of the Donut bolts must be tightened evenly, as failure to do so will damage the Donut Clamp.

Do not over tighten as this may also result in damage.

POSITION

LOOSEN TIGHTEN

D Mount Displays

Choose the correct Mounting Screws supplied in the bits box and attach the display as shown.

Note: Extension

Clips are included to suit VESA 100mm x 100mm (4” x 4”)

Mounting Hole

Patterns.

100mm (4”)

75mm (3”)

75mm

(3”)

100mm

(4”)

F Cable Management

Insert display cables into the slots in each pole, using

Cable Balls to hold them in place.

Note: When the slot in each pole cannot be used, use the supplied Cable Clip’s to secure the display cables.

Cable

Balls

Cable

Clips

E Adjust Ball Joint Mechanism

Adjust the Ball Joint

Mechanism to suit the weight of your display.

Tighten or loosen screws evenly with the supplied 2.5mm Allen

Key, 1/4 turn at a time.

LOOSEN

2.5mm

Allen Key

TIGHTEN

Note: Ensure enough slack is left in cables to allow for movement.

As LCD Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility it the mounting hole pattern does not comply with the international VESA standards.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 29.08.07©