Advent CCS562 Installation manual


Add to my manuals
10 Pages

advertisement

Advent CCS562 Installation manual | Manualzz

Model: CCS562

Commercial Camera System

(IR Camera & 5.6” Monitor)

Installation Manual

Features

• 5.6” High Resolution LCD Monitor

• Built in Speaker

• Two video inputs

• Fully Adjustable

• Auto brightness adjustment

• Commercial camera with Infra Red Capability and Built in

Microphone using Sony CCD technology.

• 12v or 24v power.

Table of Contents

Warnings ......................................................................................3

Product Description .....................................................................4

Packing List .................................................................................4

System Installation......................................................................5

Wiring Diagram ...........................................................................7

Specifications ..............................................................................9

Troubleshooting ...........................................................................9

2

Warnings

The product is intended to assist in safe driving and to allow the driver to have a broader rear view while the vehicle is in reverse.

You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of your vehicle.

Audiovox Electronics Corporation cannot accept any responsibility whatsoever for accidents resulting from failure to observe these precautions or safety instructions.

1. This product utilizes high voltage. Any unauthorized modifications or damage to the product may result in electrical shock. Handle all components with care. Inspect regularly for damage to components and cabling.

2. You are responsible for ensuring that the installation of this product does not void or affect the vehicle manufacturer’s warranty. Audiovox Electronics Corporation or its subsidiaries are not liable in full or in part for improper installation resulting in loss or damage to your property, or for voiding all or part of the vehicle manufacturer’s warranty.

3. Do not apply excessive force to any of the components contained within this kit. Excessive force used before, during or after installation that results in a damaged or non-functional part will void all warranties.

4. Please follow the procedures in this installation manual.

Improper installation or modification of this product will void all warranties.

3

Product Description

This advanced high resolution monitor and camera system will show a clear picture from a reversing camera or any other video source.

The heavy duty design and high quality components make the

CCS562 ideal for all industrial and commercial applications.

The integrated wiring harness and single power wire make this system simple and fast to install.

Packing List

CCS562 Parts Barcode # Quantity

20M Extension Cable & 2 Adaptors

2.8M Harness Cable

Mounting Bracket

Mounting Kit

Silicon Tape

30272170

30272420

30272060

30272020

1

1

1

1

1

4

System Installation

1. Choose the mounting location for the CAM150 commercial camera on the rear of the vehicle. We recommend a position as high as possible and in the center of the vehicle.

2. Choose a suitable place in the vehicle cabin to mount the 5.6” LCD

Screen. We recommend dash mounting in the corner of the vehicle.

3. Examine the vehicle to determine the best way to run the power wires to: LCD monitor, accessory power, the reverse lights and to the camera at the rear of the vehicle.

4. Attach the screen to the dash using the supplied 3M adhesive pad or mounting screws. The mounting bracket has been designed to be bent to match the shape of the mounting location.

5. Attach the camera to the rear of the vehicle using the supplied mounting screws of bolts.

6. Run the extension cable from the camera to the front of the vehicle.

7. Run the wiring harness from the LCD monitor and connect up with the

Camera extension cable.

8. Attach reverse & accessory power wires.

9. Connect your reversing camera.

Note: When using an Advent CCS System, the signal and power for the camera will be supplied through the monitor extension cable. Please also note that the microphone in the camera will be played on the speaker built into the LCD monitor.

10. Connect the LCD Monitor to the harness.

11. Power up and adjust on screen settings.

NOTE: To adjust monitor and volume settings press the menu button on screen to cycle through the menu options.

5

Wiring the Camera to the Vehicle’s Reverse

Lamp

1. Locate the reverse lamp in the tail light assembly.

2. Using the tap connector supplied, perform the following steps: a) Place the un-stripped positive lead from the tail lamp in the run channel, which runs completely through the connector. b) Insert the un-stripped red power wire from the camera completely into the other channel in the connector. c) Make the connection between the wires by crimping down the metal connector with a pair of pliers, making sure the metal is flush with the plastic insulator. d) Close the top plastic hinged cover until latched.

3. Attach the black wire to the ground (negative).

4. Repeat the above steps for the red wire.

6

Wiring Diagram

Note: The power and signal will be provided through a single cable from the monitor.

7

Specifications

1. Voltage: DC12V-DC24V

2. Current: 7w

3. LCD Brightness: 350cd/m2

4. LCD Contrast Ratio: 300:1

5. Image Display: Selectable Normal/Reverse Image

6. LCD: Adjustable Viewing Angle

7. Camera Viewing Angle: 150 degrees

8. Minimum Illumination: 0 Lux (w/ Infra Red)

9. Horizontal Resolution: 420 TV Lines

10. Dimensions: LCD (150x126x27)mm Camera (82x73x58)mm

Troubleshooting

Symptom Solution

No power to the monitor 1. Check that reverse power is attached to orange wire.

2. Check that accessory power is attached to red wire

3. Check that black is attached to vehicle body

(ground)

4. Check fuse and if blown ONLY replace is fuse of same amperage.

No image from backup camera when vehicle placed in reverse

Image is mirrored or requires adjustment

Sound can not be heard from

Advent camera

1. Check that camera is functioning correctly

2. Check that orange wire is attached to reverse power.

3. Check that backup camera is attached to input CAM1.

1. All settings are adjusted by pressing on the menu button and cycling through to

MIRROR settings

1. Increase volume through MENU options

8

7

© 2008 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788

8

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Frequently Answers and Questions

What does CCS562 provide?
CCS562 provides a clear visual from a reversing camera or other video source with its 5.6" LCD monitor.
Where is the recommended mounting location for the CAM150 commercial camera?
As high as possible in the center of your vehicle.
How do I connect my reversing camera?
The signal and power for your camera will be supplied through the monitor extension cable.
What is the minimum illumination for the backup camera?
0 Lux with Infra Red.
How do I adjust the monitor and volume settings?
Press the menu button on the screen to cycle through the menu options.
What are the voltage and current specifications?
DC12V-DC24V voltage and 7w current.
What is the horizontal resolution of the camera?
420 TV Lines.
What are the dimensions?
LCD (150x126x27)mm, Camera (82x73x58)mm.
Download PDF

advertisement