advertisement
Multimedia Projector
MODEL
PLC-XU22N
Owner's Manual
2
INFORMATION TO THE USER
NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
TO THE OWNER
As the owner of a new Multimedia Projector, you are probably eager to try out your new projector. Before you do, we suggest that your spend a little time reading this manual to familiarize yourself with the operating procedures, so that you will receive maximum satisfaction from the many features included in your new projector.
This owner's manual will acquaint you with your projector's features. Reading it will help us too. Through the years, we have found that many service requests were not caused by problems with our projectors. They were caused by problems that could have been prevented, if the owner had followed the instructions in the manual.
You can often correct operating problems yourself. If your projector fails to work properly, see
"TROUBLESHOOTING" section on pages 44 ~ 45 and try the solution marked for each problem.
SAFETY PRECAUTIONS
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
This Projector has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature.
This projector produces intense light from the projection lens. Do not stare directly into the lens as possible eye damage could result. Be especially careful that children do not stare directly into the beam.
The Remote Control Unit, supplied to this projector, emits the laser beam as the Laser Pointer function from the Laser Light Window while pressing the LASER button (for 1 minute). Do not look into the Laser
Light Window or shine the laser beam on yourself or other people. Eye damage may result.
This projector should be set in the way indicated. If not, It may result in fire hazard.
If the projector will not be used for an extended time, unplug the projector from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE CONSTITUTING
A RISK OF ELECTRIC SHOCK IS
PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT
.
IMPORTANT SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before the product is operated.
Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Do not use attachments not recommended by the manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall of shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.
Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...
Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.
The openings should never be covered with cloth of other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.
This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.
This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.
Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
20cm d. If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been damaged.
f. When the projector exhibits a distinct change in performance-this indicates a need for service.
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.
GROUND
This projector is equipped with a grounding type AC line plug.
Should you be unable to insert the plug into the outlet, contact your electrician. Do not defeat the safety purpose of this grounding type plug.
Follow all warnings and instructions marked on the projectors.
For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained.
Do not cover the ventilation slot on the projector.
Heat build-up can reduce the service life of your projector, and can also be dangerous.
PROJECTOR
(FRONT)
PROJECTOR
(SIDE)
WALL
50cm 50cm 50cm
3
TABLE OF CONTENTS
FEATURES AND DESIGN 5
PREPARATION 6
NAME OF EACH PART OF THE PROJECTOR 6
SETTING-UP THE PROJECTOR
POSITIONING THE PROJECTOR
7
7
ADJUSTABLE FEET
CONNECTING THE AC POWER CORD
VENTILATION
MOVING THE PROJECTOR
8
9
7
8
CONNECTING THE PROJECTOR 10
TERMINALS OF THE PROJECTOR 10
CONNECTING TO THE VIDEO EQUIPMENT 11
CONNECTING TO THE COMPUTER 12
BEFORE OPERATION
OPERATION OF THE REMOTE CONTROL
LASER POINTER FUNCTION
REMOTE CONTROL BATTERIES INSTALLATION
TOP CONTROLS AND INDICATORS
14
14
14
15
16
MCI MODE
OPERATING THE PC CARD SLOT
SELECTING MCI MODE
SHOW THE DATA IN THE MEMORY CARD
WRITE DATA INTO THE MEMORY CARD
PICTURE IMAGE ADJUSTMENT
PICTURE POSITION ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
SMART MEDIA AND PC CARD ADAPTER
32
36
36
37
38
32
33
34
35
4
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Windows and PowerPoint are registered trademarks of Microsoft Corporation.
● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.
FEATURES AND DESIGN
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.
◆
Compatibility
This projector is compatible with many different types of personal computers and video devices, including;
● IBM-compatible computers, including laptops, up to 1280 x 1024 resolution.
● Apple Macintosh and PowerBook computers up to 1280 x 1024 resolution.
● Various video equipment using any of the world wide video standards, including
NTSC, NTSC4.43, SECAM, PAL, PAL-M and PAL-N.
◆
PC CARD SLOT
This projector has the PC CARD SLOT for easier presentation. Pictures can be projected just by inserting a memory card including image data and the presentation data can be edited by the software "Media Card Imager"
(supplied) easily. Refer to the pages 32 ~ 39 and the Owner's Manual for Media Card imager for operations.
◆
Laser Pointer Function
The Remote Control Unit of this projector has the Laser Pointer function providing convenience and smartness for your presentations.
◆
Image Resolution
Picture Image of the computer is projected in the resolution of 1024 x 768 and it is provided just as appearing on your computer's monitor.
Screen resolutions between 1024 x 768 and
1280 x 1024 are compressed to 1024 x 768, and this projector cannot display screen resolutions above 1280 x 1024. If your computer's screen resolution is higher than
1280 x 1024, reset it to a lower resolution before you connect the projector.
◆
Other Features
This projector has Motor Zoom/Focus, No
Show, Picture Freeze, Keystone and Mute functions. And the Air Pad Remote Control is equipped.
◆
Portability
This projector is quite compact in size and weight. Having a sophisticated shape like an attaché case with a retractable carrying handle, the projector will help you make powerful presentation wherever you go.
◆
Automatic Multiscanning System
This projector automatically tune to the most personal computers currently distributed by simply connecting. It is free from complicated adjustments to project picture images from PC.
◆
Accessories
This projector comes with the parts listed below. Check to make sure all are included. If any parts are missing, contact to a sales dealer.
● Owner's Manual.
● AC Power Cord.
● Wireless Remote Control Unit.
● Batteries for Remote Control Unit.
● VGA Cable.
● Control Cable for PS/2 Port.
● Media Card Imager for Windows 95 (CD-ROM) and Owner’s Manual for this software.
● SmartMedia and PC Card Adapter.
● Lens Cover.
● Dust Cover.
◆
Multilanguage Menu Display
Operation menu is displayed in; English,
Deutsch, Français, Italiano, Español, or
Japanese
5
6
PREPARATION
NAME OF EACH PART OF THE PROJECTOR
FRONT OF THE CABINET
PROJECTION LENS
PC CARD SLOT
LENS COVER
INFRARED REMOTE RECEIVER
SPEAKER (Monaural)
CARRY HANDLE
BACK OF THE CABINET
EXHAUST VENT
HOT AIR EXHAUSTED !
Air blown from the exhaust vent is hot.
When using or installing the projector, following attention should be taken.
● Do not put a flammable object near this part.
Keep heat-sensitive objects away from the exhaust vent.
● Do not touch this part especially screws and metallic parts. This part will become hot while the projector is used.
POWER CORD CONNECTOR
INFRARED
REMOTE RECEIVER
BOTTOM OF THE CABINET
AIR INTAKE VENTS
These Air Intake Vents should not be blocked.
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
LAMP COVER
8
PREPARATION
CONNECTING THE AC POWER CORD
This projector uses nominal input voltages of 100-120 V
AC. The projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor.
To reduce the risk of electrical shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if your are not sure of the type of power supply being in use.
Connect the projector with the peripheral equipment before turning the projector on. (Refer to pages 10 ~ 13 for connection.)
CAUTION
For the safety, unplug the AC Power Cord when the appliance is not used.
When this projector is connected to the outlet with the AC Power Cord, the appliance is in Stand-by
Mode and consumes a little electric power.
Connect the AC power supply cord (provided) to the projector.
The socket-outlet must be near this equipment and must be easily accessible.
Projector side (Female) AC outlet side (Male)
VENTILATION
This projector is equipped cooling fans for protection from overheating. Pay attention to the following to ensure the ventilation and avoid a possible risk of fire and malfunction.
● Do not cover the vent slot.
● Keep the rear grill at least one meter away from any object.
● Make sure that there is no object on both sides of the projector. Those obstacles may prevent the projector from taking the cooling air through the side Air Intake
Vent Slots.
EXHAUST VENT
(REAR SIDE)
AIR INTAKE VENTS
(BOTH SIDES)
PREPARATION
MOVING THE PROJECTOR
Use the Carry Handle when moving the Projector.
When moving the projector, replace the lens cover and rotate the feet fully clockwise (to shorten the feet) to prevent from damage to the lens and the cabinet.
When this projector is not used for the extended period, replace the lens cover, tuck the Adjustable Feet and apply the dust cover supplied to this projector.
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR
● Do not drop or give a shock to the projector, otherwise damages or malfunctions may result.
● When carrying the projector, use a carrying case recommended by Sanyo.
● Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause damage to the projector. To transport the projector through a courier or transport service, use a case recommended by Sanyo.
● For carrying or transportation cases, contact a Sanyo authorized dealer.
9
CONNECTING THE PROJECTOR
TERMINALS OF THE PROJECTOR
S-VIDEO INPUT JACK
Connect the S-VIDEO output from the video equipment to this terminal.
(Refer to P11.)
AUDIO INPUT JACKS
Connect the audio outputs from the video equipment to these terminals.
(Refer to P11.)
● When the audio output is monaural, connect it to the Left jack.
COMPUTER INPUT TERMINAL
Connect the computer output to this terminal.
(Refer to P12, 13.)
MONITOR OUTPUT TERMINAL
This terminal outputs the signal from the COMPUTER IN terminal. Connect to the monitor to this terminal.
(Refer to P12, 13.)
S-VIDEO
R-AUDIO-L (MONO)
COMPUTER IN
VIDEO
AUDIO
IN
OUT
MONITOR OUT
CONTROL PORT
VIDEO INPUT JACK
Connect the video output from the video equipment to this terminal.
(Refer to P11.)
COMPUTER AUDIO INPUT JACK
Connect the audio output from the computer to this terminal.
(Refer to P12, 13.)
AUDIO OUTPUT JACK (STEREO)
Connect the audio amplifier to this terminal.
(Refer to P12, 13.)
CONTROL PORT CONNECTOR
When controlling the computer with the Remote Control of this projector, connect the mouse port of your personal computer to this terminal. It is also used for write on or read from the data of the PC CARD SLOT in
MCI mode.
(Refer to P12, 13, 35.)
COMPUTER INPUT / MONITOR OUTPUT TERMINAL
Terminal : HDB15-PIN
Connect the display output terminal of the computer to COMPUTER INPUT with the VGA Cable (supplied). And connect the monitor to MONITOR OUTPUT with the monitor cable (not supplied). When connecting the Macintosh computer, the
MAC/VGA Adapter (not supplied) is required.
Pin Configuration
5 4
10
15 14
9
3
13
8
2
12
7
1
11
6
7
8
5
6
1
2
3
4
Red Input
Green Input
Blue Input
Sense 2
Ground (Horiz.sync.)
Ground (Red)
Ground (Green)
Ground (Blue)
9
10
11
12
13
14
15
Non Connect
Ground (Vert.sync.)
Sense 0
Sense 1
Horiz. sync.
Vert. sync.
Reserved
CONTROL PORT CONNECTOR
Terminal : DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this terminal with the Control Cable (the Control
Cable for PS/2 port is supplied).
Pin Configuration
5
8 7 6
4 3
2 1
7
8
5
6
3
4
1
2
PS/2 Serial ADB
-----
CLK
DATA
GND
-----
-----
GND
-----
R X D
-----
-----
GND
RTS
T X D
GND
GND
-----
ADB
-----
GND
-----
-----
-----
GND
10
S-VIDEO
R-AUDIO-L (MONO) VIDEO
AUDIO
IN
OUT
COMPUTER IN
MONITOR OUT
CONTROL PORT
CONNECTING THE PROJECTOR
CONNECTING TO THE COMPUTER
To connect with the computer, refer to the figure below.
Used cables for connection
• VGA CABLE
• CONTROL CABLE FOR PS/2 PORT
• CONTROL CABLE FOR SERIAL PORT,or ADB PORT ✽
• MAC ADAPTER ✽
• MONITOR CABLE ✽
• PC AUDIO CABLE (stereo) ✽
✽ These cables are not supplied with this projector.
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA)
Desktop type
Laptop type
Monitor
Audio Speaker
(stereo)
12
Audio Amplifier
To the Monitor
To each terminal of your computer
Monitor Output
ON DIP
1 2 3 4 5 6
MAC Adapter ✽
Set the slide switches following the chart on the next page.
Serial port PS/2 port
Terminal Terminal
ADB port Audio Output
Terminal
Audio Input
Audio Cable (stereo)
✽
Control Cable for ADB Port ✽
Control Cable for PS/2 Port
Control Cable for Serial Port ✽
VGA Cable
Monitor Cable ✽
NOTE :
When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
CONNECTING THE PROJECTOR
S-VIDEO
R-AUDIO-L (MONO) VIDEO
AUDIO
IN
OUT
COMPUTER IN
MONITOR OUT
CONTROL PORT
COMPUTER
IN
MONITOR
OUT
CONTROL
PORT
AUDIO
IN
AUDIO
OUT
Use one of these Control
Cables corresponding with the terminal of your computer.
◆ MAC ADAPTER (Not supplied)
Set the switches as shown in the table below depending on the RESOLUTION
MODE that you want to use before your turn on the projector and computer.
ON
OFF
ON DIP
1 2 3 4 5 6
13" MODE (640 x 480)
16" MODE (832 x 624)
19" MODE (1024 x 768)
21" MODE (1152 x 870)
1 2
ON ON
OFF ON
OFF
ON
3
OFF
OFF
ON ON
ON ON
4 5 6
OFF OFF OFF
ON OFF OFF
OFF OFF OFF
ON OFF OFF
13
BEFORE OPERATION
OPERATION OF THE REMOTE CONTROL
ON
ALL OFF
VIDEO BUTTON
Used to select VIDEO source. (P30)
COMPUTER/MCI BUTTON
Used to select source either
COMPUTER or MCI mode.
(P23, 33)
MENU BUTTON
Used to call MENU operation. (P17-19)
COMPUTER/
MCI VIDEO
ON-OFF
ZOOM FOCUS VOLUME
MUTE
D.ZOOM
PAGE
MENU
POWER ON-OFF BUTTON
Used to turn the projector on or off. (P20)
POINT BUTTON
Used to move the pointer on the MENU, to adjust the item, or to pan the image in DIGITAL
ZOOM mode. (P29, 37)
It is also used as a PC mouse in Wireless Mouse Operation.
(P41)
✽ When pressing the center of this button, it works as the SELECT button.
ALL-OFF SWITCH
When using the Remote Control
Unit, turn this switch to “ON” and turn it “ALL OFF” when it is not used.
SELECT BUTTON
Used to execute the item selected or to expand the image in DIGITAL ZOOM mode. (P29, 37)
It is also used as a PC mouse in Wireless Mouse Operation.
(P41)
LASER BUTTON
Used to operate laser pointer function. The laser beam is emitted while pressing this button within 1 minute. When using the laser pointer for more than 1 minute, release the button and press it again.
LASER
NO SHOW
KEYSTONE
FREEZE
AUTO IMAGE NORMAL
This remote control emits a laser beam as the Laser Pointer from the Laser Light Window. When the LASER button is pressed, the laser light goes on. And when the button is pressed more than 1 minute or the button is released, light goes off.
Laser light is emitted with the RED light which tells the laser beam being emitted.
The laser emitted is a class II laser; therefore, do not look into the Laser Light Window or shine the laser beam on yourself or other people. The three marks bellow are the caution labels for the laser beam.
CAUTION : Use of controls or adjustments or performance of procedures other than those specified herein may result hazardous radiation exposure.
14
BEFORE OPERATION
ZOOM BUTTON
Used to adjust zoom.
(P21)
COMPUTER/
MCI VIDEO
ON-OFF
ZOOM FOCUS VOLUME
FOCUS BUTTON
Used to adjust focus.
(P21)
MUTE
D.ZOOM
PAGE
MENU
MUTE BUTTON
Used to mute sound.(P22)
VOLUME BUTTON
Used to adjust volume.
(P22)
D.ZOOM BUTTON
Used to turn the projector into DIGITAL ZOOM mode. (P29, 37)
Operating Range
Point the remote control toward the projector (Receiver Window) whenever pressing the buttons.
Maximum operating range for the remote control is about 16.4’ (5m) and 60° front and rear of the projector
60°
16.4’
(5 m)
NO SHOW BUTTON
Used to turn the picture into black image. (P22)
AUTO IMAGE BUTTON
Use to operate AUTO
IMAGE function. (P28)
LASER
NO SHOW
KEYSTONE
FREEZE
AUTO IMAGE NORMAL
FREEZE BUTTON
Used to stop the picture.
(P22)
NORMAL BUTTON
Used to reset to normal picture adjustment preset by the factory.
(P27, 31, 36)
KEY STONE BUTTON
Used to correct the key stone distortion.
(P22, 29, 30, 37)
60°
16.4’
(5 m)
REMOTE CONTROL BATTERIES INSTALLATION
1
Remove the battery compartment lid.
Press the lid downward and slide it.
2
Slide the batteries into the compartment.
Two AA size batteries
For correct polarity (+ and –), be sure the battery terminals are in contact with the pins in the compartment.
3
Replace the compartment lid.
To insure safe operation, please observe the following precautions :
● Use (2) AA type alkaline batteries.
● Replace two batteries at the same time.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid.
● Do not expose the Remote Control Units to moisture, or heat.
● Do not drop the remote control unit.
● If batteries have leaked on the remote control, carefully wipe the case clean and load new batteries.
15
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
AUTO IMAGE BUTTON
Used to operate AUTO
IMAGE function. (P28)
POWER ON–OFF BUTTON
Used to turn the projector on or off. (P20)
LAMP INDICATOR
This indicator is lit in dim when the projector is turned on. And the light is brightened when the projector is in stand-by mode.
READY INDICATOR
This indicator is lit in green when the projector is ready to be turned on.
WARNING TEMP. INDICATOR
This indicator flashes red when internal projector temperature is too high.
(P42)
LAMP
READY
WARNING
TEMP.
LAMP
REPLACE
LAMP REPLACE INDICATOR
This indicator turns to yellow when the life of the projection lamp draws to an end. (P43)
MENU BUTTON
Used to open or close the
MENU operation.
(P17, 19)
NORMAL PAGE VOLUME
AUTO IMAGE
ON–OFF MENU
ZOOM
SELECT
MODE
FOCUS
NORMAL BUTTON
Used to reset to normal picture adjustment preset by factory. (P27, 31, 36)
PAGE BUTTONS
Used to move to the next / previous page of the data in the memory card plugged into PC CARD SLOT.
These buttons are used to stop or resume AUTO-
PLAY function. Page buttons are activated in
MCI mode. (P34.)
VOLUME BUTTONS
Used to adjust volume.
(P22)
MODE BUTTON
Used to select input source among Computer, Video or
MCI. (P23, 30, 33)
SELECT BUTTON
Used to execute the item selected. It is also used to expand the image in
DIGITAL ZOOM mode.
(P29, 37)
POINT BUTTONS
Used to select an item and adjust the value on the
MENU. It is also used to pan the image in DIGITAL
ZOOM mode. (P29, 37)
FOCUS BUTTONS
Used to select focus adjust.
(P21)
ZOOM BUTTONS
Used to select zoom adjust.
(P21)
16
SELECT
BEFORE OPERATION
MENU BAR
MENU BAR IN COMPUTER MODE Press MENU BUTTON while being in Computer mode.
MODE MENU
Used to select the Computer input mode.
(Refer to P23)
SYSTEM MENU
Used to select a computer system.
(Refer to P23)
POSITION MENU
Used to adjust the position of the image.
(Refer to P28)
PC ADJUST MENU
Used to adjust the parameters to match with the input signal format.
(Refer to P24, 25)
SETTING MENU
Used to set the Display
Menu and to reset
Lamp Replacement
Monitor Timer.
(Refer to P40)
18
AUTO IMAGE MENU
Used to adjust Fine sync., Total dots, and Picture Position automatically.
(Refer to P28)
IMAGE MENU
Used to adjust the computer image. [Fine sync. / Total dots /
White Balance /
Contrast / Brightness]
(Refer to P27)
SCREEN MENU
Used to adjust the size of the image or to correct the
Keystone distortion.
(Refer to P29)
LANGUAGE MENU
Used to select the language used in the
Menu.
(Refer to P40)
MENU BAR IN VIDEO MODE Press MENU BUTTON while being in Video mode.
MODE MENU
Used to select the Video input.
(Refer to P30)
IMAGE MENU
Used to adjust the picture image. [ Color /
Tint / White Balance /
Contrast / Brightness/
Sharpness ]
(Refer to P31)
These icons have the same function as the Computer Mode.
SYSTEM MENU
Used to select a color system among
[ PAL, SECAM, NTSC,
NTSC 4.43, PAL-M and
PAL-N ].
(Refer to P30)
SCREEN MENU
Used to set the size of the image either
Regular or Wide, or to correct the
Keystone distortion.
(Refer to P30)
MENU BAR IN MCI MODE
MODE MENU
Used to select the MCI input mode.
(Refer to P33)
Press MENU BUTTON while being in MCI mode.
POSITION MENU
Used to adjust the position of the image.
(Refer to P36)
These icons have the same function as the Computer Mode.
VIEW MENU
Used to display, read or write the image data in a memory card through the PC CARD
SLOT.
(Refer to P34, 35)
IMAGE MENU
Used to adjust the computer image. [White
Balance / Contrast
/ Brightness]
(Refer to P36)
SCREEN MENU
Used to adjust the size of the image or to correct the
Keystone distortion.
(Refer to P37)
19
BASIC OPERATIONS
TURNING ON / OFF THE PROJECTOR
TURNING ON THE PROJECTOR
1 Complete the peripheral connections (with Computer, VCR, and etc.) before turning on the projector. (Refer to
"CONNECTING TO THE PROJECTOR" on Pages 10~13 for connecting those equipment.
2 Connect the projector's AC power cord into a wall outlet. The
LAMP indicator lights RED, and the READY indicator lights
GREEN.
3 Press the power ON-OFF button on the Remote Control Unit or on the Top Control to ON. The LAMP POWER indicator dims, and the Cooling Fans start to operate. The Preparation Display appears on the screen and the count-down starts. The signal from the source appears after 30 seconds.
30
The Preparation Display disappears after 30 seconds.
1
2
3
TURNING OFF THE PROJECTOR
Press the power ON-OFF button on the Remote Control Unit or on the Top Control, and the message "Power off?" appears on the screen.
Press again the power ON-OFF button to turn off the projector.
The LAMP indicator lights bright and the READY indicator turns off. The Cooling Fans operate for 90 seconds after the projector is turned off. (During this "Cooling Down" period, this appliance cannot be turned on.)
When the cooling the projector has finished, the READY indicator turns to green again and you can turn the projector on. After cooling down completely, disconnect the AC power cord.
Power off?
The message disappears after 4 seconds.
TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU TURN IT ON, WAIT AT LEAST 5
MINUTES BEFORE TURNING IT OFF.
When the TEMPERATURE WARNING indicator flashes red, the projector is automatically turned off. Wait at least 5 minutes before turning the projector on again.
If the TEMPERATURE WARNING indicator continues to flash, follow procedures below:
1. Disconnect the AC power cord from the AC outlet.
2. Check the air filters for dust accumulation.
3. Clean the Air Filter. (See "AIR FILTER CARE AND CLEANING" section on page 42.)
4. Press the power ON-OFF button to ON.
If the TEMPERATURE WARNING indicator still continues to flash, call your authorized dealer or service station.
NOTE: The Cooling Fan may work for cooling while the projector is turned off. When the Cooling
Fan is working, TEMPERATURE WARNING INDICATOR flashes red.
20
BASIC OPERATION
ADJUSTING THE IMAGE
ZOOM ADJUSTMENT
1 Press the ZOOM button on the Top Control or the ZOOM ▲ / ▼ button on the Remote Control Unit to turn into the ZOOM mode.
2 Press the POINT UP button or the ZOOM ▲ button to have the image larger, and press the POINT UP button or the ZOOM ▼ button to have the smaller.
In the Computer mode, the image can be expanded, compressed, and panned with the Digital Zoom function. Refer to page 29, 37 for the Digital Zoom operation.
Zoom
The message disappears after 4 seconds.
1
FOCUS ADJUSTMENT
Press the FOCUS button on the Top Control or the FOCUS
▲ / ▼ button on the Remote Control Unit to turn into the FOCUS mode.
2 Adjust the focus of the image by pressing the POINT
UP/DOWN button or the FOCUS ▲ / ▼ button.
Focus
The message disappears after 4 seconds.
KEYSTONE ADJUSTMENT
If the picture obtained keystone distortion, correct screen with KEYSTONE adjustment.
1 Press the KEYSTONE ▲ / ▼ button on the Remote Control Unit or select the Keystone on the SCREEN menu. (Refer to page
29, 30, 37.) The message “Keystone” is displayed.
Keystone
2 Correct the Keystone distortion by pressing the KEYSTONE
▲ / ▼ button or the POINT UP/DOWN button(s). Press the
KEYSTONE ▲ button or the POINT UP button to reduce the upper part or the image, and press the KEYSTONE ▼ button or the POINT DOWN button to reduce the lower part.
The message disappears after 4 seconds.
Reduce the upper width with the KEY STONE ▲ button or the POINT UP button.
Reduce the lower width with the KEY STONE ▼ button or the POINT DOWN button.
21
BASIC OPERATION
NO SHOW FUNCTION
Press the NO SHOW button on the Remote Control Unit to turn the picture into black image. This function is cancelled when the NO
SHOW button is pressed again or any other function button is pressed.
No show
The message disappears after 4 seconds.
PICTURE FREEZE FUNCTION
Press the FREEZE button on the Remote Control Unit to turn the picture remained on-screen. This function is cancelled when the FREEZE button is pressed again or any other function button is pressed.
SOUND ADJUSTMENT
SOUND VOLUME ADJUSTMENT
Press the VOLUME (+/–) button(s) on the Top Control or on the
Remote Control Unit to adjust the volume. The Volume dialog box appears on the screen for a few seconds.
The VOLUME (+) button to increase the volume, and The VOLUME
(–) button for decreasing.
SOUND MUTE ADJUSTMENT
Press the MUTE button on the Remote Control Unit to cut off the sound. To restore the sound to its previous level, press again or press Volume button(s).
It indicates the level of the volume.
Press the MUTE button to set the Mute function On or Off.
The display disappears after 4 seconds.
22
COMPUTER MODE
SELECTING COMPUTER MODE
DIRECT OPERATION
Select COMPUTER mode by pressing the MODE button on the Top
Control or the COMPUTER / MCI button on the Remote Control Unit.
MODE button
COMPUTER
MCI
COMPUTER / MCI button
COMPUTER
MCI
VIDEO
MENU OPERATION
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select Computer press the SELECT button. and
CURRENT MODE DISPLAY
When selecting the Computer Mode, the Current Mode display appears. It shows the information of the computer of the mode selected.
Providing the information of the computer detected by the projector.
SELECTING COMPUTER SYSTEM
AUTOMATIC MULTISCANNING SYSTEM
This projector automatically tunes to most different types of computer based on VGA, SVGA, XGA or SXGA (refer to “COMPATIBLE
COMPUTER SPECIFICATION” on page 26). When selecting
Computer, this projector automatically tunes to the incoming signal and projectors the proper image without any special setting. (Setting of the Computer System may be required when connecting some computers.)
Note : The projector may provides the messages below.
Go to PC adj.
The projector cannot discriminate or detect the input signal from the computer. Adjust and set the computer system manually. (Refer to page 24.)
No signal
There is no signal input from the computer. Make sure the connection of the computer and the projector is set correctly. (Refer to
TROUBLESHOOTING on page 44.)
SYSTEM BOX
It displays the SYSTEM being selected.
The system being selected.
SELECT COMPUTER SYSTEM MANUALLY
To set the Computer system manually, select the mode on the ON-
SCREEN MENU.
1
2
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select
SYSTEM and press the SELECT button. Another dialog box
COMPUTER MODE Menu will appear.
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the system that you want to set, and then press SELECT button.
The systems on this dialog box can be selected.
Close the SYSTEM
Menu.
23
COMPUTER MODE
PC ADJUSTMENT
This Projector can automatically tune to the display signals from most personal computers currently distributed.
However, some computers employ the special signal formats which are different from the standard ones and may not be tuned by Multiscanning of this projector. If this happens, the projector cannot reproduce a proper image and the image is recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has PC ADJUSTMENT function, to enable you to precisely adjust several parameters to match with those exceptional signal formats and the projector has five independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it.
1
2
3
4
5
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT RIGHT/LEFT buttons to select PC
ADJUST and press the SELECT button. Another dialog box “Where to reserve” Menu will appear.
In this dialog box, you can store the parameter into the area from “Mode 1” to “Mode 5.” When memorizing the new computer parameter, select the Mode with the message of
“Free” by pressing the POINT UP/DOWN buttons and the
SELECT button. To change the parameters of the Mode previously set, select the Mode with “Stored.”
When the Mode is selected, Parameter adjustment dialog box appears. Move the arrow to the item that you want to change by pressing the POINT UP/DOWN buttons, and adjust the each item to match with your computer. To change the value, press either the POINT RIGHT button or the POINT LEFT button.
Refer to the next page for adjusting each item.
Move the arrow to “Stored” and press the SELECT button. The parameter is memorized in the selected Mode.
To activate the Mode manually adjusted in this PC
ADJUSTMENT Menu, select the Mode at the SYSTEM
SELECT Menu. (Refer to page 23.)
This Mode has parameters being stored.
The Vacant Mode.
Manual set Computer
Mode (1 to 5).
Close the PC
ADJUSTMENT Menu.
Press the POINT
RIGHT/LEFT button(s) to adjust the value.
Press the
SELECT button to set Full screen function on/off.
24
Total lines
The number of the total vertical lines. Adjust the number to match the image of your personal computer.
Total dots
The number of the total dots in one horizontal period. Adjust the number to match the image of your personal computer.
Horizontal / Vertical
Adjustment of the horizontal or vertical |picture position. When the image is not centered on the screen, adjust each of those items.
Clamp
Adjustment of the clamp level. When the image has a dark bar(s), try this adjustment.
Display area
Adjustment of the area displayed with this projector. Select the resolution at the Display area dialog box, or adjust the number at the column of “H” or “V” to match the resolution of the image.
Full Screen
Set “On” to resize the image with 4 x 3 aspect ratio to fit the screen.
Each of the keys operates as follow.
Reset Recalls the parameter data that previously adjusted.
Mode free
Stored
Quit
Clears the parameter data previously set in the selected Mode.
Stores the parameters in the memory.
Closes the PC ADJUST Menu.
Press the
SELECT button to select the typical resolution of the image.
25
COMPUTER MODE
26
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140 MHz of Dot Clock.
32.70
38.00
49.72
48.36
68.677
60.023
56.47
60.31
48.50
44.00
63.48
36.00
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
H-Freq.
(kHz)
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
15.734
15.625
35.156
ON-SCREEN
DISPLAY
RESOLUTION
VGA 1 640 x 480
VGA 2
VGA 3
720 x 400
640 x 400
VGA 4
VGA 5
VGA 6
640 x 480
640 x 480
640 x 480
VGA 7 640 x 480
MAC LC13 640 x 480
MAC 13
RGB
RGB
SVGA 1
640 x 480
640 x 480
(Interlace)
768 x 576
(Interlace)
800 x 600
800 x 600
800 x 600
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
SVGA 10 800 x 600
SVGA 11 800 x 600
MAC1 6
XGA 1
XGA 2
XGA 3
XGA 4
XGA 5
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
XGA 6
XGA 7
XGA 8
XGA 9
1024 x 768
1024 x 768
1024 x 768
1024 x 768
(Interlace)
ON-SCREEN
DISPLAY
RESOLUTION
XGA 10 1024 x 768
XGA 11
XGA 12
XGA 13
XGA 14
1024 x 768
1024 x 768
(Interlace)
1024 x 768
1024 x 768
XGA15 1024 x 768
MAC 19 1024 x 768
MAC21 1152 x 870
SXGA 1 1152 x 864
SXGA 2 1280 x 1024
SXGA 3 1280 x 1024
SXGA 4 1280 x 1024
SXGA 5 1280 x 1024
SXGA 6 1280 x 1024
SXGA 7 1280 x 1024
SXGA 8 1280 x 1024
SXGA 9 1280 x 1024
SXGA 10 1280 x 960
SXGA 11 1152 x 900
SXGA 12 1152 x 900
SXGA 13
SXGA 14
1280 x 1024
(Interlace)
1280 x 1024
(Interlace)
SXGA 15 1280 x 1024
SXGA 16 1280 x 1024
SXGA 17 1152 x 900
SXGA 18
1280 x 1024
(Interlace)
SXGA 19 1280 x 1024
MAC 1280 x 960
MAC 1280 x 1024
HDTV720p 1280 x 720
HDTV1035i
HDTV1080i
1920 x 1035
(Interlace)
1920 x 1080
(Interlace)
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
43.59
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
V-Freq.
(Hz)
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
30
25
56.25
61.20
71.40
50.00
50.00
63.37
76.97
61.85
46.43
64.20
62.50
63.90
63.34
63.74
71.69
81.13
63.98
79.976
60.00
H-Freq.
(kHz)
62.04
61.00
35.522
46.90
47.00
58.03
60.24
68.68
63.79
75.00
80.00
45.00
33.75
33.75
65.20
75.60
43.00
47.00
60.01
72.00
66.00
43.35
70.40
58.60
60.00
59.98
60.01
67.19
76.107
60.02
75.025
60.00
V-Freq.
(Hz)
77.07
75.70
43.48
58.20
58.30
72.0
75.08
75.06
60.18
75.08
75.08
60.00
60.00
60.00
NOTE : Specifications are subject to change without notice.
PICTURE IMAGE ADJUSTMENT
ADJUST PICTURE IMAGE MANUALLY
1
2
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select
IMAGE and press the SELECT button. Another dialog box
PICTURE IMAGE ADJUSTMENT Menu will appear.
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the item that you want to change by pressing the POINT UP/DOWN buttons. To change the value, press either the POINT RIGHT button or the POINT LEFT button.
Fine sync.
Adjust the picture as necessary to eliminate flicker from the display.
(From 0 to 127.)
Total dots
The number of the total dots in one horizontal period. Adjust the number to match your PC image.
White balance (Red / Green / Blue)
Move the arrow to Red, Green, or Blue that you want to adjust.
Press POINT LEFT button to adjust the color of image lighter, and press POINT RIGHT button to adjust deeper. (From 0 to 63.)
Contrast
Press POINT LEFT button to adjust the image lighter, and press
POINT RIGHT button to adjust deeper. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust the image darker, and press
POINT RIGHT button to adjust brighter. (From 0 to 63.)
Each of the keys operates as follow.
Reset
Stored
Quit
Recalls the data previously adjusted.
Stores the adjusted data in the memory.
Closes the PICTURE IMAGE ADJUSTMENT Menu.
COMPUTER MODE
It indicates the level of the item.
Move the arrow to the item and press
POINT RIGHT /
LEFT button.
Close the PICTURE
IMAGE ADJUSTMENT
Menu.
NORMAL FUNCTION
The normal picture level is preset on this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Units). The “Normal” display will be displayed on the screen for a few seconds.
Normal
27
COMPUTER MODE
28
AUTO IMAGE FUNCTION
The Auto Image function is provided to automatically adjust Fine sync., Total dots, and Picture Position for most computers.
1
2
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select
AUTO IMAGE and press the SELECT button.
Another dialog box AUTO IMAGE Menu will appear.
Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN button. Change the setting On or Off by pressing the SELECT button.
Fine sync.
Adjust the picture as necessary to eliminate flicker from the display.
This item can be adjusted manually. (Refer to page 27.)
Total dots
The number of the total dots in one horizontal period. This item can be adjusted manually. (Refer to page 27.)
Position
Adjustment of the position of the image. This item can be adjusted manually. (Refer to page 28.)
Starts the adjustment on the item set to "On".
Close the PICTURE IMAGE
ADJUSTMENT Menu.
3 Move the arrow to “Go!” and press the SELECT button to start the Auto Image function.
This adjustment can be executed by pressing AUTO IMAGE button on the Top Control and the Remote Control Unit.
Stored
Go!
Stores the On/Off setting of each item.
Starts the Auto Image Adjustment.
Quit Closes the AUTO IMAGE ADJUSTMENT Menu.
NOTE : The Fine sync., Total dots, and Picture Position of some computers may not be fully adjusted with the Auto Image
Function. In that case, manual adjustment is required to make fine image. (Refer to page 27 to adjust "Fine sync." or
"Total dots" and page 28 to adjust Picture Position.)
Move the arrow to the item and then press the SELECT button.
PICTURE POSITION ADJUSTMENT
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION
ADJUSTMENT.
1
2
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select
POSITION and press the SELECT button. The PICTURE
POSITION dialog box will appear.
Move the image by pressing the POINT UP / DOWN / RIGHT /
LEFT buttons.
PICTURE POSITION dialog box
Press the POINT UP /
DOWN / RIGHT / LEFT buttons to move the image
COMPUTER MODE
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the image in desirable size.
1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select
SCREEN and press the SELECT button. Another dialog box PICTURE SCREEN Menu will appear.
2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the function that you want to select and then press SELECT button.
True
To turn the image into its original size select True in the dialog box.
When the original image size is larger than the screen size (1024 x
768), this projector becomes Digital Zoom mode automatically.
Move the arrow to the function and press the
SELECT button.
Keystone
When the image is distorted vertically, select Keystone in the dialog box. The ON-SCREEN menu and SCREEN ADJUST menu disappears and the message “Keystone” is displayed. Correct the
Keystone distortion by pressing the KEYSTONE ▲ / ▼ button or the
POINT UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT on page 21.
Digital Zoom
To adjust the image size or pan the image, select Digital zoom in the dialog box. The ON-SCREEN menu and SCREEN ADJUST menu disappears and the message “D. Zoom” is displayed.
This projector is also turned into Digital Zoom mode by pressing the D.ZOOM ▲ / ▼ button on the Remote Control Unit.
Refer to the following for operation.
Expand function
To expand the image size, press the D.ZOOM ▲ button or the SELECT button. The image is magnified by degrees.
Compress function
To compress the image size, press the D.ZOOM ▼ button or the RIGHT CLICK button. The size of image is reduced by degrees.
Panning function
To pan the image, press the POINT UP/DOWN/LEFT/RIGHT buttons. Panning function can work only when the image is larger than the screen size.
To cancel Digital Zoom mode, press the any buttons except D.ZOOM ▲ / ▼ , SELECT, RIGHT CLICK, POINT, PAGE
▲ / ▼ or LASER button. To adjust the image to the screen size (1024 x 768), press NORMAL button.
● This projector cannot display in the resolution higher than 1280 X 1024. If your computer’s screen resolution is higher than 1280 X 1024, reset the resolution to the lower before connecting the projector.
● The image data in other than XGA (1024 x 768) is modified to fit the screen size in the initial mode.
● The normal "Panning Operation" may not function properly if the computer system prepared with the "PC Adjust" is used.
29
VIDEO MODE
SELECTING VIDEO MODE
DIRECT OPERATION
Select VIDEO mode by pressing the MODE button on the Top
Control or the VIDEO button on the Remote Control Unit.
MODE button
COMPUTER
MCI
MENU OPERATION
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select Video press the SELECT button. and
SELECTING COLOR SYSTEM
1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select
SYSTEM and press the SELECT button. Another dialog box
VIDEO SYSTEM Menu will appear.
2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to "Auto", and then press the SELECT button.
Auto
The projector automatically detects the incoming Video system, and adjusts itself to optimize its performance.
When the Video System is PAL-M or PAL-N, select the system manually.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If the projector cannot reproduce the proper video image, it is required to select a specific broadcast signal format among PAL,
SECAM, NTSC, NTSC 4.43, PAL-M, or PAL-N.
VIDEO
This box indicates the system being selected.
Move the arrow to the Mode and press the SELECT button.
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the image in desirable size.
1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select
SCREEN and press the SELECT button. Another dialog box PICTURE SCREEN ADJUSTMENT DISPLAY will appear.
2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the screen size that you want to set, and then press the SELECT button.
Regular
Normal Video Image size with 4 x 3 aspect ratio.
Wide
Resizes the image for wide screen size with 16 x 9 aspect ratio.
Keystone
When the image is distorted vertically, select Keystone in the dialog box. Correct the Keystone distortion by pressing KEYSTONE ▲ / ▼ button or POINT UP/DOWN button(s). Refer to KEYSTONE
ADJUSTMENT on page 21.
Move the pointer to the function that and press the SELECT button.
30
VIDEO MODE
PICTURE IMAGE ADJUSTMENT
1
2
ADJUSTING THE PICTURE IMAGE
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select
IMAGE and press the SELECT button. Another dialog box
PICTURE IMAGE ADJUSTMENT Menu will appear.
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the item that you want to adjust by pressing the POINT UP/DOWN buttons. To change the value, press either the POINT RIGHT button or the POINT LEFT button.
Color
Press POINT LEFT button to adjust the image lighter, and press
POINT RIGHT button to adjust deeper. (From 0 to 63.)
Tint
Press POINT LEFT button to adjust the color more purple, and press POINT RIGHT button to adjust more green. (From 0 to 63.)
White balance (Red / Green / Blue)
Move the arrow to Red, Green, or Blue that you want to adjust.
Press POINT LEFT button to adjust the color of image lighter, and press POINT RIGHT button to adjust deeper. (From 0 to 63.)
Contrast
Press POINT LEFT button to adjust the image lighter, and press
POINT RIGHT button to adjust deeper. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust the image darker, and press
POINT RIGHT button to adjust brighter. (From 0 to 63.)
Sharpness
Press POINT LEFT button to adjust the image softer, and press
POINT RIGHT button to adjust sharper. (From 0 to 63.)
Each of the keys operates as follow.
Reset Recalls the data previously adjusted.
Stored Stores the data in the memory.
Quit Closes the PICTURE IMAGE ADJUSTMENT Menu.
NORMAL FUNCTION
The normal picture level is preset on this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Unit). The "Normal" display will be displayed on the screen for a few seconds.
Normal
It indicates the level of the item.
Move the arrow to the item and press
POINT RIGHT /
LEFT button.
Close the PICTURE
IMAGE ADJUSTMENT
Menu.
31
MCI MODE
OPERATING THE PC CARD SLOT
This projector has PC CARD SLOT and the pictures in a memory card (SmartMedia with PC Card Adapter or
PC card) can be displayed just by inserting the card into it. It is unnecessary to connect with other input equipment. Media Card Imager (supplied with CD-ROM) can edit the image data and record it into a memory card for projecting with the projector.
PC with Windows 95
Media Card Imager
(CD-ROM) MC I
PC Card
(not supplied)
Digital Camera
SmartMedia with PC Card Adapter
(supplied)
PC CARD SLOT (Front)
HOW TO LOAD THE MEMORY CARD INTO THE PROJECTOR
LOAD
Insert PC Card Adapter (with SmartMedia) or PC card into PC CARD
SLOT. Make sure EJECT button pops out.
NOTE : Be sure to insert the memory card with the front side to the left side of the projector. Do not insert the card in the reverse. The card may be damaged.
PC CARD SLOT
UNLOAD
Press EJECT button, and the memory card pops out.
NOTE : Do not take the card out while the PC CARD SLOT loading.
Data and the card can be damaged.
Memory Card
Insert with the front side of the card to the left side of the projector.
PC CARD INDICATOR
WHEN THIS INDICATOR IS LIGHTING, THE
PROJECTOR IS READING OR WRITING THE
DATA INTO THE MEMORY CARD. DO NOT
REMOVE THE MEMORY CARD. DATA IN
THE MEMORY CARD MAY BE DAMAGED.
EJECT BUTTON
32
AVAILABLE DATA
This projector can project the image data as follow through PC
CARD SLOT.
● The data edited by “Media Card Imager.”
● The data of the resolution between VGA (640 X 480) and SXGA
(1280 X 1024) in Bit Map type (BMP) or JPEG type (JPG), such as
Digital Camera data, can be also displayed.
(Some image data in SXGA size may not be displayed properly.
In that case, reset the resolution to the lower.)
Refer to “SHOW THE DATA IN THE MEMORY CARD” on page 34 to display the image data.
Media Card Imager
Media Card Imager (CD-ROM) is attached to this projector to edit the image data for projecting. Installation of Media Card
Imager is recommended. Refer to
Owner’s Manual of Media Card Imager for installation and operation.
AVAILABLE CARD
SmartMedia (with PC Card Adapter) or Type || PCMCIA-ATA Card can be used with this projector. (Those memory cards are supplied with this projector.)
Refer to SMARTMEDIA AND PC CARD ADAPTER on pages 38 and 39 for operation.
NOTE : Some PCMCIA Adapter or PC Card is not available for this projector and cannot provide the image data. In that case, use our SmartMedia and PC Card Adapter.
SELECTING MCI MODE
When the memory card is inserted into PC CARD SLOT, mode is automatically set to MCI mode and the first
Page of the latest Index is projected on the screen. To turn Video/Computer mode to MCI mode manually, operate as follows.
DIRECT OPERATION
Select MCI mode by pressing the MODE button on the Top Control or the COMPUTER / MCI button on the Remote Control Unit.
MODE button
COMPUTER
COMPUTER / MCI button
COMPUTER
MCI MCI
VIDEO
MENU OPERATION
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select MCI and press the SELECT button.
33
MCI MODE
SHOW THE DATA IN THE MEMORY CARD
1
BASIC OPERATION
Insert the memory card and turn the projector into MCI mode.
The image in the memory card is displayed.
2 To change the image to others, press the PAGE ▲ or ▼ button. (When the “Display Timer” is set in the image with the
Media Card Imager, the image is changed to another automatically.)
To select Index or Page in the table, follow the instructions of
INDEX SELECTION and PAGE SELECTION.
Index and Page
The data edited with Media Card Imager is the Index format consisting of several Pages. To project the desirable image, select the Index and then select the Page in the Index.
Index
Select the Index
Pages in the Index
● This projector can project only the image data in Bit Map type or in JPEG type or the data edited by Media Card Imager
(supplied) through the PC CARD SLOT. Other data is not available and should be edited and written in a memory card with Media Card Imager before loading PC CARD SLOT.
(The data in Bit Map type or in JPEG type, such as the data captured with a digital camera, can be projected directly through PC CARD SLOT.)
● If there are the data edited by Media Card Imager and other data (such as in Bit Map type or JPEG type) together in one memory card, the data edited by Media Card Imager has a priority to be projected with the LCD projector. The other image data in Bit Map type or JPEG type is not projected. In that case, edit those data and write in the memory card with the Media Card Imager.
1
2
3
INDEX SELECTION
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select VIEW and press the SELECT button. Another dialog box VIEW
SETTING menu will appear.
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to "Index", and then press the
SELECT button. The table of Indexes in the memory card will appear.
Press the POINT UP/DOWN/LEFT/RIGHT buttons to move to the Index that you want to project and press the SELECT button. The first Page of the Index selected is displayed.
(Press SELECT button again to display the table of Pages.)
Move the arrow to each operation and press the SELECT button.
1
2
3
PAGE SELECTION
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select VIEW and press the SELECT button. Another dialog box VIEW
SETTING menu will appear.
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to "Page", and then press the
SELECT button. The table of pages of the index card will appear.
Press the POINT UP/DOWN/LEFT/RIGHT buttons to move to the Page that you want to project and press the SELECT button. The page selected is displayed on the screen.
The table of Pages can be displayed by pressing the SELECT button when the page is displayed on full screen.
34
MCI MODE
WRITE DATA INTO THE MEMORY CARD
The data edited by Media Card Imager in the computer can be written in or read from the memory card with the
PC Card drive of your Personal Computer or the PC CARD Slot of this projector.
The data edited by Media Card Imager is written in Bit Map type (BMP) or JPEG type (JPG).
ACCESS TO THE MEMORY CARD THROUGH THE PROJECTOR
If your computer doesn't have the PC card writing equipment, the data can be written or read by connecting with this projector.
NOTE : This operation can be made only by Media Card Imager in the Personal Computer.
Connect the projector to the Personal Computer with the
Control Cable for Serial Port (optionally supplied / refer to page 12, 13).
1 Connect the projector to your computer with the Control Cable for Serial Port (optionally supplied). (Refer to “CONNECTING
COMPUTER” on Page 12, 13.)
Insert the memory card into PC CARD SLOT of the projector.
And then, turn on the projector first and the computer.
2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select View and press the SELECT button. Another dialog box VIEW
SETTING Menu will appear.
3 Press POINT DOWN button and a red arrow appear. Move the arrow to Card access by pressing POINT UP/DOWN button.
And then press SELECT button. “Ready to access” is displayed.
Operate Media Card Imager of your computer to write/read the data in the PC card. (Refer to Owner's Manual of Media Card
Imager for operation.)
NOTE : Connect the projector to the computer with Control Cable before turning those appliances on.
Do not press any button while read/write the data through
PC CARD Slot of the projector. Those operations are canceled and the data in the memory card may be damaged.
Move the arrow to
“Card access” and press the SELECT button.
35
MCI MODE
PICTURE IMAGE ADJUSTMENT
ADJUST THE PICTURE IMAGE MANUALLY
1
2
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select
IMAGE and press the SELECT button. Another dialog box
PICTURE IMAGE ADJUSTMENT Menu will appear.
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the item by pressing the POINT
UP/DOWN buttons. To change the value press either the
POINT RIGHT button or the POINT LEFT button.
White balance (Red / Green / Blue)
Move the arrow to Red, Green, or Blue that you want to adjust.
Press POINT LEFT button to adjust the color of image lighter, and press POINT RIGHT button to adjust deeper. (From 0 to 63.)
Contrast
Press POINT LEFT button to adjust the image lighter, and press
POINT RIGHT button to adjust deeper. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust the image darker, and press
POINT RIGHT button to adjust brighter. (From 0 to 63.)
Each of the keys operates as follow.
Reset Recalls the data previously adjusted.
Stored Stores the adjusted data in the memory.
Quit Closes the PICTURE IMAGE ADJUSTMENT Menu.
NORMAL FUNCTION
The normal picture level is preset on this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Units). The "Normal" display will be displayed on the screen for a few seconds.
Normal
It indicates the level of the item.
Move the arrow to the item and press
POINT RIGHT /
LEFT button.
Close the PICTURE
IMAGE ADJUSTMENT
Menu.
36
PICTURE POSITION ADJUSTMENT
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION
ADJUSTMENT.
1
2
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select
POSITION and press the SELECT button. The PICTURE
POSITION dialog box will appear.
Move the image by pressing the POINT UP / DOWN / RIGHT /
LEFT buttons.
PICTURE POSITION dialog box
Press the POINT UP /
DOWN / RIGHT / LEFT buttons to move the image
MCI MODE
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the image in desirable size.
1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select
SCREEN and press the SELECT button. Another dialog box PICTURE SCREEN Menu will appear.
2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the function that you want to select and then press SELECT button.
True
To turn the image into its original size select True in the dialog box.
When the original image size is larger than the screen size (1024 x
768), this projector becomes Digital Zoom mode automatically.
Move the arrow to the function and press the
SELECT button.
Keystone
When the image is distorted vertically, select Keystone in the dialog box. The ON-SCREEN menu and SCREEN ADJUST menu disappears and the message “Keystone” is displayed. Correct the
Keystone distortion by pressing KEYSTONE ▲ / ▼ button or POINT
UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT on page 21.
Digital Zoom
To adjust the image size or pan the image, select Digital zoom in the dialog box. The ON-SCREEN menu and SCREEN ADJUST menu disappears and the message “D. Zoom” is displayed.
This projector is also turned into Digital Zoom mode by pressing
D.ZOOM ▲ / ▼ button on the Remote Control Unit.
Refer to the following for operation.
Expand function
To expand the image size, press D.ZOOM ▲ button or SELECT button. The image is magnified by degrees.
Compress function
To compress the image size, press the D.ZOOM ▼ button or the RIGHT CLICK button. The size of image is reduced by degrees.
Panning function
To pan the image, press POINT UP/DOWN/LEFT/RIGHT buttons. Panning function can work only when the image is larger than the screen size.
To cancel Digital Zoom mode, press the any buttons except D.ZOOM ▲ / ▼ , SELECT, RIGHT CLICK, POINT, PAGE
▲ / ▼ , AUTO IMAGE, or LASER button. To adjust the image to the screen size (1024 x 768), press NORMAL button.
● This projector cannot display in the resolution higher than 1280 X 1024. If your computer’s screen resolution is higher than 1280 X 1024, reset the resolution to the lower before connecting the projector.
● The image data in other than XGA (1024 x 768) is modified to fit the screen size in the initial mode.
37
MCI MODE
SMARTMEDIA AND PC CARD ADAPTER
SmartMedia and PC Card Adapter are provided with this LCD projector. SmartMedia can be used as a PC card conforming to the PC Card Standard-ATA by combining with PC Card Adapter.
INSTALL / REMOVE THE SMARTMEDIA
INSTALL
Insert SmartMedia fully into PC Card Adapter. Make sure EJECT button pops out.
NOTE : The front side of SmartMedia has Contact Area on its surface.
The front side of PC Card Adapter has Eject button on the left side of the slot.
Do not insert SmartMedia in the reverse. The card and the data can be damaged.
PC Card Adapter
(supplied)
SmartMedia
(supplied)
REMOVE
To remove SmartMedia, fully press in the EJECT button. The card pops out, then take out the card.
NOTE : Do not pull SmartMedia by force. It may damage
SmartMedia or PC Card Adapter.
EJECT button
38
MCI MODE
PRECAUTIONS AND SPECIFICATIONS OF THE SMARTMEDIA
● SmartMedia is a precision device. Do not bend it, drop it, subject it to strong forces or shocks or place where strong static electrical charge can be generated.
● Do not touch the surface of the Contact Area with fingers or allow it to be stained with foreign materials. Store SmartMedia inside its protective case when it is not used.
● SmartMedia is a consumable item. The data may not be written in or read from SmartMedia by using for a long time. In that case, replace SmartMedia with new one.
Memory capacity : 8MB
Operating voltage : 3.3 V DC
Usage environment
Temperature : 0~55 °C (during use)
-20~65 °C (during storage)
Humidity : less than 95% (during use, during storage)
CAUTION
Write Protect Sticker is not available for PC. When PC attempts to read the data from SmartMedia with Write Protect Sticker, it provides the error messages or the control of PC becomes insecure because of the property of the interface. When the error messages are displayed, press any key to return to the normal display. It is recommended, however, SmartMedia should be used on PC without Write Protect Sticker.
① Contact Area
Data is written in Contact Area. Never scratch or stain this area.
➁ Write Protect Area
Affix Write Protect Sticker onto Write
Protect Area to prevent from accidental erasure.
➂ Index Area
Affix Index Label onto Index Area.
PRECAUTIONS AND SPECIFICATIONS OF THE PC CARD ADAPTER
● Do not bend it, drop it, subject it to strong forces or shocks or place where strong static electrical charge can be generated.
● Do not insert materials other than SmartMedia. The adapter may be damaged. Store PC Card Adapter inside its protective case when it is not used.
● Do not shake the adapter, turn off the appliances, or remove
SmartMedia from the PC Card Adapter during writing or reading data. It may damage the data in SmartMedia.
Operating voltage : 5 V DC
Usage environment
Temperature : 0~55 °C (during use)
-20~65 °C (during storage)
Humidity : less than 95%
(during use, during storage)
This adapter can be adapted to only our SmartMedia indicated below.
Available SmartMedia : 3.3V / 5V, 2MB / 4MB / 8MB /16MB
39
SETTING
SETTING MENU
1
2
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select
SETTING and press the SELECT button. Another dialog box SETTING Menu will appear.
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the item that you want to set, and then press the SELECT button to set it "On" or "Off".
Blue back
When this function is in the "On" position, this projector will produce a blue image instead of the video noise on the screen when all the input source is unplugged or turned off.
Display
When this function is in the "On" position, the On-
Screen Displays always appear when adjustments are made. (The following displays disappear by switching this function "Off.")
● Preparation Display
(The Number-counting-down Display)
● Mode Display
● Volume/Mute Display
● Zoom Display
● Focus Display
● Normal Display
● No show Display
● Keystone Display
● D.Zoom Display
Ceiling
Rear
Split wipe
Lamp age
When this function is in the “On” position, the top / bottom and the left / right reversed picture is provided to project the image from a ceiling mounted projector.
When this function is in the “On” position, the left / right reversed picture is provided to project the image to a rear projection screen.
Turn this function “On” position in the SETTING menu.
The picture will change into next one by sliding black image side ways like drawing the black curtains when the input source is turned into another one.
The Lamp age function is designed to reset the lamp replacement monitor timer. When replacing the lamp, reset the lamp replacement monitor timer by using this function. (Refer to page 43.)
Ceiling function
Rear function
Set the Pointer to the item, and then press the SELECT button.
SELECTING LANGUAGE
The language used in the ON-SCREEN MENU is selectable from among English, German, French, Italian, Spanish and Japanese.
1
2
Press the MENU button and the ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to select
LANGUAGE and press the SELECT button. Another dialog box LANGUAGE Menu will appear.
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the language that you want to set, and then press the SELECT button.
Move the Pointer to the language that you want to set, and then press the SELECT button.
40
APPENDIX
OPERATING WIRELESS MOUSE
The Wireless Remote Control Unit is not only able to operate the projector but also usable as a wireless mouse for most Personal Computers. The POINT buttons and the two CLICK buttons are used for the wireless mouse operation.
The wireless mouse is usable when PC mouse pointer is displayed on the screen. When the menu or the indicator of the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse cannot be used.
INSTALLATION
To use the Wireless Remote Control Unit as the Wireless Mouse for a Personal Computer, installation of the mouse driver (not supplied) is required. Make sure that the mouse driver is properly installed in your computer. And make sure that the mouse port of the computer connected to Control Port is activated.
1
2
Connect the mouse port of your computer to the Control Port of the projector with the Control Cable. (Refer to page 10 to 13 for connection.)
Turn the projector on first, and then turn on your computer.
When the computer is switched on first, the Wireless Mouse may not work properly.
Note : When the computer has no mouse port, connect the Serial
Port of the computer to Control
Port of the projector with the
Control Cable for Serial Port.
OPERATING WIRELESS MOUSE
When controlling the pointer of the computer, operate the Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK button on the Wireless Remote Control Unit.
POINT button
Used to move the pointer. The pointer is moved corresponding with the direction you are pressing.
POINT button (Move the pointer)
SELECT (LEFT CLICK) button
This button has the same function as the left button in a PC mouse.
RIGHT CLICK button
This button has the same function as the right button in a PC mouse.
Pressing this button does not affect any operation when in Menu mode.
SELECT button
(left button of the mouse)
RIGHT CLICK button
(right button of the mouse)
41
APPENDIX
MAINTENANCE
TEMPERATURE WARNING INDICATOR
1
2
3
The TEMPERATURE WARNING Indicator flashes red when the internal temperature of the projector exceeds the normal temperature. The Indicator stops flashing when the temperature of the projector become normal.
When the TEMPERATURE WARNING Indicator continues to flash, check the item listed below.
The Ventilation slots of the projector may be blocked. In such an event, reposition the appliance so that the ventilation slots are not obstructed.
Air filters are clogged with dust particles. Clean the air filters by following AIR FILTER CARE AND CLEANING below.
If the TEMPERATURE WARNING Indicator remains on after performing the above checks, the Cooling Fans or the
Internal Circuits may be malfunctioning. Request service from an authorized dealer or service station.
AIR FILTER CARE AND CLEANING
The Removable Air Filters prevent dust from accumulating on the surface of the Projection Lens and the
Projection Mirror. Should the Air Filters become clogged with dust particles, it will reduce the Cooling Fans' effectiveness and may result in internal heat build up and adversely affect on the life of the projector.
Clean the Air Filters following the steps below:
1
2
3
Turn the power off, and disconnect the AC power cord from the
AC outlet.
Turn the projector upside down and remove 2 Air Filters by pulling the latches of them upward.
Clean the Air Filters with brush or wash out the dust and particles.
AIR FILTERS
4 Replace the Air Filter. Make sure that the Air Filters are fully inserted.
CAUTION
Do not operate the projector with the Air Filter removed.
The dust is stuck on the LCD Panel and the Mirror, and it may spoil the fine picture image.
Do not put the small parts into the Air Intake Vents. It result in the malfunction of the projector.
The Air Filter is small part. Take care that children don’t eat or swallow it.
RECOMMENDATION
We recommend to avoid dusty/smoky place for operating the projector. Using in dusty place may cause the picture of poor quality.
When using under the dusty or smoky conditions, dust may accumulate on the liquid crystal panel and lens inside it, and may resultantly be projected on the screen together with the picture.
When the above symptoms are noticed, contact your authorized dealer or service station for the cleaning.
CLEANING THE PROJECTION LENS
2
3
Follow these steps to clean the projection lens:
1 Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
Lightly wipe the cleaning cloth over the lens.
When you don't use the projector, replace the lens cover.
42
APPENDIX
LAMP REPLACEMENT INDICATOR
When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights red.
When the image becomes dark or the color of the image become unnatural, replacement of the Lamp is required.
LAMP REPLACEMENT
CAUTION
● For continued safety, replace with a lamp assembly of the same type.
● Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector can become very hot.
● Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury.
Follow these steps to replace the lamp assembly.
1 Turn off the projector and disconnect the AC plug. Allow the projector to cool for at least 45 minutes.
2
3
4
Remove a screw with a screwdriver and remove the Lamp
Cover.
Remove 2 screws with a screwdriver and pull out the Lamp
Assembly by grasping the handle.
Replace the Lamp Assembly with new one and tighten 2 screws. Make sure that the Lamp Assembly is set properly.
And replace the Lamp Cover and tighten a screw.
LAMP COVER
HANDLE
5
6
Connect the AC Power Cord to the projector and turn the projector on.
Reset the Lamp Replacement Monitor Timer (refer to the section “Lamp Replacement Monitor Timer” below).
NOTE : Do not reset the LAMP REPLACEMENT MONITOR
TIMER, when the lamp is not replaced.
LAMP
ASSEMBLY
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer. When ordering the Lamp, give the following information to the dealer.
● Model No. of your projector : PLC-XU22N
● Replacement Lamp Type No. : POA-LMP21J
(Service Parts No. 610 280 6939)
LAMP REPLACEMENT MONITOR TIMER
Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the
Lamp Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting.
1
2
Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT
LEFT/RIGHT buttons to select SETTING dialog box SETTING MENU will appear. and press the SELECT button (refer to the page 40). Another
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to Lamp age, and then press the
SELECT button. The message "Lamp replace monitor Reset?" is displayed.
3 Select [Yes] to reset the Timer.
Do not reset the Lamp Replacement Monitor Timer, except after the lamp is replaced.
43
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service station for assistance, check the matters below once again.
1. Make sure you have connected the projector to your equipment a s described in section "CONNECTING THE
PROJECTOR" on pages 10 ~ 13.
2. Check cable connection. Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If the projector still does not produce the image, re-start the computer.
5. If the image sill does not appear, unplug the projector from the computer and check the computer monitor's display. The problem may be with your graphics controller rather than with the projector. (When you reconnect the projector, remember to turn the computer and monitor off before your power up the projector.
Power the equipment back in order of : Projector and computer.)
6. If the problem still exists, check with following chart.
Problem:
No power.
Image is out of focus.
Try these Solution
● Plug the projector into the AC outlet.
● Be sure READY Indicator light is On.
● Wait 90 seconds after the projector is turned OFF before turning the projector back on.
NOTE : After pressing the power ON-OFF switch to OFF, make sure the projector works as follow.
1. The LAMP indicator will light and the READY indicator will turn off.
2. After 90 seconds, the READY indicator will light green again and the projector may be turned on by pressing the power ON-OFF button.
● Check the TEMPERATURE WARNING indicator. If the indicator flashes red, the projector cannot be turned on.
(See "TURNING ON/OFF THE PROJECTOR" section on page 20.)
● Check the Projection Lamp. (Refer to the page 43.)
● Adjust the focus
● Make sure the projection screen is at least 4.6’ (1.4m) from the projector.
● Check the projection lens to see if it needs cleaning.
NOTE : Moving the projector from a cool temperature location to a warm temperature location may result in moisture condensation on the lens. In such an event, leave the projector OFF an d wait until condensation disappears.
● Check Ceiling / Rear feature. (See “SETTING” section on page 40.)
Picture is Left/Right reversed.
Picture is
Top/Bottom reversed.
Some displays are not seen during the
Operation.
No image.
No sound.
● Check Ceiling feature. (See “SETTING” section on page 40.)
● Check Display feature.(See “SETTING” section on page 40.)
● Check the connection between the computer or video equipment and the projector.
● When turning the projector on, it is about 30 seconds to display the image.
● Check the system that you select is corresponding with the computer or the video equipment.
● Make sure the temperature is not out of the Operating Temperature (5° ~ 35°).
● Check audio cable connection from audio input source.
● Adjust the audio source.
● Press VOLUME (+) button.
● Press MUTE button.
44
APPENDIX
Problem:
Remote Control
Units dose not work.
Wireless Mouse function does not work.
The image data in memory card isn’t displayed.
The image data can’t be written in, read from the memory card.
Try these Solution
● Check the batteries.
● Check the ALL-OFF switch on the Remote Control Unit is set to “ON.”.
● Make sure anything is blocking between the Remote Receiver and the Remote Control
Units.
● Make sure you are not too far from the projector when using the Remote Control Units.
Maximum operating range is 16.4’ (5m).
● Check the cable connection between the projector and the computer.
● Check the mouse setting on your computer.
● Turn the projector before your turn on the computer.
● Check the memory card is inserted properly into PC CARD SLOT.
● Check SmartMedia or PC Card Adapter is set properly.
● Check MCI mode is selected.
● Check the image data is recorded in the memory card properly.
● Start the projector again.
● Check the projector is turned on.
● Check “Card access” in VIEW menu is selected.
● Check Control Cable for Serial Port (optional) is connected properly.
● Check the memory card is inserted properly into PC CARD SLOT.
● Check Media Card Imager (supplied) is installed in your computer properly.
● Check the setting in Media Card Imager (like Serial Port Setting) is set properly.
WARNING :
High voltages are used to operate this projector. Do not attempt to open the cabinet.
Sanyo Service is easily obtained. If after following all operating instructions, you find that service is necessary, contact the SFS Corporation in Los Angeles, or the store where you purchased the unit. Give the model number and explain the difficulty. We will advise you how to obtain service.
45
46
TECHNICAL SPECIFICATIONS
Projector Type
Dimensions (W x H x D)
Net Weight
LCD Panel System
Panel Resolution
Number of Pixels
Color System
Scanning Frequency
Projection Image size (Diagonal)
Horizontal Resolution
Projection Lens
Throw Distance
Projection Lamp
AV Input Jacks
Computer Input Jacks
Control Port Jack
Monitor Output Jack
Computer Audio Input Jack
Audio Output Jack
Internal Audio Amp
Built-in Speaker
Feet Adjustment
Voltage
Power Consumption
Operating Temperature
Storage Temperature
Remote Control Transmitter
Accessories
Multi-media Projector
9.41" x 3.54" x 12.72"(239mm x 90mm x 323mm) (not including Adjustable Feet)
8.82 lbs (4.0 kg)
0.9" TFT Active Matrix type, 3 panels
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 30” to 300”
800 TV lines
F 1.7 ~ 2.0 lens with f 33.2mm ~ 43.1mm Motor zoom and focus
4.6’ ~ 35.4’ (1.4 m ~ 10.8 m)
150 W
RCA Type x 1 (Video, Audio R and L) and DIN 4 pin (S-Video) x 1
(VGA) HDB 15 Terminal x 1
DIN 8 pin x 1
(VGA) HDB 15 Terminal x 1
Mini Jack (stereo)
Mini Jack (stereo)
1W RMS (Monaural)
1 speaker, 1.57" x 1.18" (40mm x 30mm)
0˚ to 10˚
AC 100 ~ 120 V, 50 / 60 Hz
2.5 A (Max. Ampere)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Power Source : AA Type x 2
Operating Range : 16.4’ (5m) / ±30˚
Dimensions
Net Weight :
: 2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
0.35 lbs (160 g) (including batteries)
Laser Pointer : Class II Laser (Max. Output : 1mW / Wave length : 650±20nm)
Owner’s Manual
AC Power Cord
Remote Control Transmitter and Batteries
VGA Cable
Control Cable for PS/2 port
Media Card Imager for Windows 95 (CD-ROM) and Owner's Manual for this software
SmartMedia and PC Card Adapter
Dust Cover
Lens Cover
● The specifications are subject to change without notice.
OPTIONAL PARTS
The parts listed below are optionally supplied. When ordering those parts, give the name and the Type No. of it to the sales dealer.
● Control Cable for Serial
● Control Cable for ADB
● MAC Adapter
Type No. : POA-MCSRL
Type No. : POA-MCMAC
Type No. : POA-MACAP
47
SANYO INDUSTRIAL VIDEO
LCD PROJECTOR LIMITED WARRANTY
OBLIGATIONS
In order to obtain warranty service, the product must be delivered to and picked up from and Authorized Sanyo Factory
Service Center at the user's expense, unless specifically stated otherwise in this warranty. the names and addresses of authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below.
For product operation, authorized service center referral, service assistance or problem resolution, call
CUSTOMER INFORMATION 1-800-421-5013
Weekdays 8:00 AM - 5:00 PM Pacific Time
For accessories and/or parts not available form an authorized dealer, call
PARTS ORDER INFORMATION 1-800-726-9662
Weekdays 8:00 AM - 5:00 PM Pacific Time
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED AND USED IN THE UNITED STATES OF
AMERICA, EXCLUDING ALL U.S. TERRITORIES AND PROTECTORATES, FOR INDUSTRIAL PROFESSIONAL OR
COMMERCIAL PURPOSES. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER. THE ORIGINAL DATED BILL
OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT
THE TIME WARRANTY SERVICE IS REQUESTED.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO FISHER COMPANY (SFC) warrants this
SANYO product against defects in materials and workmanship for the periods of LABOR and PARTS specified below.
SFC will repair or replace (at its option) the product and any of its parts which fall to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail.
LABOR
1YEAR
PARTS
1YEAR
LAMP
90DAYS
EXCLUSIONS
This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model's instruction manual, or (B) the repair of any product whose serial number has been altered, defaced or removed.
This warranty shall not apply to the cabinet or cosmetic parts, knobs or batteries or routine maintenance.
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.
This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear.
The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability.
SFC DISCLAIMS ALL WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE WARRANTIES OF MERCHANTABILITY
AND FITNESS), SFC'S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER,
INCLUDING WARRANTOR'S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIVE GOODS, WHETHER SUCH DEFECTS ARE
DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE EQUIPMENT.
ATTENTION
For your protection in the event of theft or loss of this product, please fill in the information below for your own personal records.
Model No.
Serial No.
(Located on back or bottom side of unit.)
Date of Purchase Purchase Price
Where Purchased
21605 Plummer Street,
Chatsworth, California 91311
Printed in Japan
Part No. 610 282 8597 (1AA6P1P2183-- MB6G)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project