Honeywell HD3MDIP User guide

EQUIP™ Series

Indoor Fixed Mini Dome

Network Camera

NTSC / PAL

HD3MDIP HD3MDIPX

User Guide

Document 800-04132V1 – Rev A – 01/10

Revisions

Issue

A

Date

09/09

V1 A 01/10

Revisions

New document for HD3MDIP/X release. Generally describes the functionality in the firmware of the HD3MDIP/X camera.

New version number and release date.

2

HD3MDIP/X Network Camera Reference Guide

Contents

Figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Overview of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Manufacturer’s Declaration of Conformance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

North America. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Warranty and Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

1

2

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Installation and Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Unpack Everything . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Overview of Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Camera Components and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Camera Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Preparing the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Preparing the Mounting Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connecting the Wires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Mounting the Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Restore Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Adjusting the Camera FOV (Field of View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Adjusting the Lens Focus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Securing the Enclosure Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

3 Installing the Honeywell IP Utility and HD3MDIP/X Web-Client Software . . . . . . . . . . . . . 29

About the Honeywell IP Utility and Web-Client. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

About the Honeywell IP Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

About the Web-Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

User Profiles: Honeywell IP Utility and Web-Client . . . . . . . . . . . . . . . . . . . . . . . . 30

Step 1: Confirm Your System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Step 2: Install the Honeywell IP Utility Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Downloading the EQUIP Series Installation Guides . . . . . . . . . . . . . . . . . . . . . . . 32

Step 3: Log Onto the IP Utility and Discover Network Devices . . . . . . . . . . . . . . . . . . . . . . 33

Step 4: Connect to a Device and Configure Network Settings . . . . . . . . . . . . . . . . . . . . . . 34

Connecting to or Disconnecting From Devices . . . . . . . . . . . . . . . . . . . . . . . . . 35

Configuring the IP Network Settings Automatically or Manually. . . . . . . . . . . . . . . . . 35

Interfacing with the EQUIP Device Via a Network Video Recorder . . . . . . . . . . . . . . . 38

Document 800-04132V1 – Rev A – 01/10 3

Contents

4

Step 5: Launch the Web-Client to View Live Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Uninstalling IP Utility, Bonjour or the ActiveX Plug-in Software . . . . . . . . . . . . . . . . . . . . . . 40

Uninstalling IP Utility Using the Start Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Uninstalling IP Utility or IP ActiveX Using the Control Panel . . . . . . . . . . . . . . . . . . . 41

IP Camera Web-Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

User Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Logging On and Off the HD3MDIP/X IP Web-Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Launching the Web-Client from IP Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Logging Onto the Web-Client from Internet Explorer . . . . . . . . . . . . . . . . . . . . . . 46

Logging Out of the Web-Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Navigating the User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Live View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Device Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

IP and Firmware Settings on the Device Information Tab . . . . . . . . . . . . . . . . . . . . 50

Compression Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Video Codec Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Statistics: Received Bit Rate and Frame Rate . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Camera Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Auto Exposure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

White Balance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Video Analytics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Sabotage Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Configuring Video Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Alarm and Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Alarm Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Appendix A Mounting Template. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Appendix B Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Problem: Lens Out of Optical Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Problem: Live View Does Not Display the Expected Video . . . . . . . . . . . . . . . . . . . . . . . . 68

Problem: Cannot Connect to a Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Appendix C Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Appendix D Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

4


Figures

Figure 4-2

Figure 4-3

Figure 4-4

Figure 4-5

Figure 4-6

Figure 4-7

Figure 4-8

Figure 4-9

Figure 4-10

Figure 4-11

Figure 4-12

Figure 4-13

Figure 4-14

Figure 4-15

Figure B-1

Figure C-1

Figure C-2

Figure C-3

Figure C-4

Figure 2-1

Figure 2-2

Figure 2-3

Figure 2-4

Figure 2-5

Figure 2-6

Figure 2-7

Figure 2-8

Figure 2-9

Figure 3-1

Figure 3-2

Figure 3-3

Figure 3-4

Figure 3-5

Figure 3-6

Figure 4-1

Document 800-04132V1 – Rev A – 01/10

HD3MDIP/X Camera Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Mounting Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Audio and Alarm PINs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Normal Alarm States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Alarm Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Camera and Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Wiring Connection Shown on Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Gimbal Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Installing the Enclosure Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Accessing Your Installation Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Honeywell IP Utility Log On Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Honeywell IP Utility User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Set the IP Network Settings Automatically or Manually . . . . . . . . . . . . . . . . . . . . 36

ActiveX Prompt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Web-Client Interface After Logging On . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Launching the HD3MDIP/X Web-Client from IP Utility . . . . . . . . . . . . . . . . . . . . 45

Web-Client Window Layout: Administrator Log On . . . . . . . . . . . . . . . . . . . . . . 47

Web-Client: Administrator User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Web-Client: Guest User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Device Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

IP and Firmware Settings: Device Information Tab . . . . . . . . . . . . . . . . . . . . . . 51

Compressions Settings Tab: Primary Stream . . . . . . . . . . . . . . . . . . . . . . . . . 52

Video Codec Settings Tab Available Functions . . . . . . . . . . . . . . . . . . . . . . . 52

Video Codec Settings, Quality Priority Selected . . . . . . . . . . . . . . . . . . . . . . . 54

Camera Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Video Analytics Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Tamper Detection Settings on the Video Analytics Tab. . . . . . . . . . . . . . . . . . . . 58

Video Analytics Alarm Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Video Analytics: Defining a Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Limited or No Connection Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

HD3MDIP/X Side View with Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

HD3MDIP/X Side View Dimensions without Skirt . . . . . . . . . . . . . . . . . . . . . . . 71

HD3MDIP/X Side View Dimensions with Adapter Plate . . . . . . . . . . . . . . . . . . . . 71

HD3MDIP/X Bottom View with Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . 71

5

Figures

6


Tables

Table 1-1

Table 2-1

Table 3-1

Table 3-2

Table 3-3

Table 3-4

Table 4-1

Table 4-2

Table 4-3

Table 4-4

Table 4-5

Table 4-6

Table 4-7

Table 4-8

Fixed Mini Dome Network Camera Model Numbers . . . . . . . . . . . . . . . . . . . . . . 13

Audio and Alarm Connector PIN Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . 19

User Profiles for Honeywell IP Utility and the Web-Client . . . . . . . . . . . . . . . . . . . 30

PC Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Items Installed On Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

IP Network Device Setting Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

User Roles and Privileges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Tabs/Views in the Web-Client Application . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Compression Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Auto Exposure Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

White Balance Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Blur Threshold Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Blinding Threshold Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Scene Change Threshold Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Document 800-04132V1 – Rev A – 01/10 7

Tables

8


About This Document

This document introduces the Honeywell HD3MDIP/X True Day/Night Indoor Network

Camera. It covers how to install and operate the HD3MDIP/X in a network environment.

This document is intended for system installers, administrators, and operators.

Overview of Contents

This document contains the following chapters and appendixes:

• Chapter 1, Introduction , introduces the Honeywell HD3MDIP/X Network Camera and gives a functional overview of its components.

• Chapter 2, Installation and Setup , provides procedures for installing cameras, adjusting the lens, and setting up a network camera environment.

• Chapter 3, Installing the Honeywell IP Utility and HD3MDIP/X Web-Client Software , describes how to install the Honeywell IP Utility and set up administrator privileges.

• Chapter 4, IP Camera Web-Client , describes how to use the Web-Client application to view video and configure the available settings for the network camera.

• Appendix A, Mounting Template , provides a mounting template for the HD3MDIP/X camera.

• Appendix B, Troubleshooting , lists common problems encountered when setting up the network camera.

• Appendix C, Specifications , provides specifications for the HD3MDIP/X camera.

• Appendix D, Glossary , explains terms and initializations used in this guide.

• The Index provides quick access to commonly searched terms.

Document 800-04132V1 Rev A

01/10

9

Cautions and Warnings

CAUTION

RISK OF

ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

THE COVER. NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES

THAT DANGEROUS VOLTAGE

CONSTITUTING A RISK OF

ELECTRIC SHOCK IS

PRESENT WITHIN THE UNIT.

THIS SYMBOL INDICATES

THAT IMPORTANT OPERATING

AND MAINTENANCE

INSTRUCTIONS ACCOMPANY

THIS UNIT.

Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty.

WARNING!

24 VAC models require the use of CSA Certified/UL Listed

Class 2 power adapters to ensure compliance with electrical safety standards. Power over Ethernet (PoE) should meet the IEEE 802.3 af PoE standard.

WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the European Union and other European countries with separate collection systems). This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.

Caution When powering the camera from 24 VAC, a UPS source should be considered to ensure satisfactory performance.

FCC Compliance Statement

Information to the User: This equipment has been tested and found to comply with the limits for a Class B digital device. Pursuant to Part 15B of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

10


If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference. For example, try reorienting or relocating the receiving antenna, increasing the separation between the equipment and receiver, or connecting the equipment to an outlet on a different circuit.

Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This Class B digital apparatus complies with Canadian ICES-003.

Manufacturer’s Declaration of Conformance

North America

The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No.

60950-1.

Europe

The manufacturer declares that the equipment supplied with this guide is compliant with the essential protection requirements of the EMC directive 2004/108/EC and the Low

Voltage Directive LVD 20006/95/EC, conforming to the requirements of standards EN

55022 for emissions, EN 50024 for immunity, and EN 60950 for Electrical Equipment safety.

Warranty and Service

Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective products returned prepaid.

In the event you have a problem with any Honeywell product, please call Customer

Service at 1.800.796.CCTV for assistance or to request a Return Merchandise

Authorization (RMA) number.

Be sure to have the model number, serial number, and the nature of the problem available for the technical service representative.


01/10

11

12

Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to Honeywell without a clearly identified Return Merchandise Authorization (RMA) number may be refused.

1

Introduction

Honeywell HD3MDIP/X color network cameras provide high picture quality remote video

surveillance over a network connection. See Table 1-1

for descriptions of the camera models.

Table 1-1

Model number

HD3MDIP

HD3MDIPX

Fixed Mini Dome Network Camera Model Numbers

Description

True Day/Night 720p, 3.3 – 12 mm VFAI Lens NTSC

True Day/Night 720p, 3.3 – 12 mm VFAI Lens PAL

Features

The Honeywell HD3MDIP/X color network camera features:

• HD, SVGA, VGA, QVGA resolutions

• 1/4" color CMOS progressive scan sensor

• Moveable Infrared (IR) cut filter ensures excellent low light performance

• Camera Sabotage Detection

• Video Motion Detection

• MPEG-4 and MJPEG compression

• Dual digital video streams simultaneously, independently configurable

• Remote firmware updates

• Supports both Dynamic and Static IP address assignment

• Multiple levels of password protected remote access prevents unauthorized users from altering system settings

• Includes advanced IP locator software to make system setup easy

• Web server for remote setup of camera video and network parameters

• 24 VAC or PoE IEEE 802.3af choice of power inputs

• Supports input and output alarm contacts

• Supports bi-directional audio

• Local video out – aim and focus


01/10

13

Introduction

14

2

Installation and Setup

This chapter describes how to:

• Mount the camera

• Adjust the camera for the clearest image

• Set up the camera in a network system

Before You Begin

Please carefully read this guide before you install the HD3MDIP/X network camera.

Keep this guide for future reference.

Before installing the camera, Honeywell recommends that you check www.honeywellvideo.com/products/cameras/ to find your camera and download the latest manuals and software updates.

Unpack Everything

Check that the items received match those listed on the order form and packing slip. The

HD3MDIP/X packing box should include, in addition to a Quick Install Guide:

• One fully-assembled HD3MDIP/X camera, including factory-installed BNC connector for local video out aim and focus

• One adapter plate

• One HD3MDIP/X hardware kit that includes mounting screws and screw caps

• One BNC cable for local video out - aim and focus

• One mounting template

• One product warranty

• One CD containing the software and this User Guide


01/10

15

Installation and Setup

If any parts are missing or damaged, contact the dealer from which you purchased your camera or call Honeywell Customer Service (see Warranty and Service ).

Equipment Required

The following tools might help you to complete the installation:

• Drill

• Screwdrivers

• Wire cutters

Overview of Installation Procedure

Note Please familiarize yourself with the installation procedure and complete each step in the exact sequence given.

The initial installation of an HD3MDIP/X camera consists of the following steps:

1

2

3

4

5

Step

Preparation

Connect the wiring.

Mount the camera.

Adjust the camera angle, position, and focus for optimum image.

Secure the enclosure cover.

Program the camera.

See …

page 18

page 21

page 24

page 25

page 27

page 55

16


Camera Components and Functions

The HD3MDIP/X Network Camera consists of a fully-integrated enclosure with camera and lens. The wiring can be completely concealed to reduce the risk of tampering.

Figure 2-1 HD3MDIP/X Camera Components

Flush Mount Back box

(not supplied)

Cover plate

Surface Mount

Skirt

Adapter plate

Camera

Interface board

Gimbal base

Base

Gimbal assembly

Turret (bubble insert)


01/10

Bubble

17


Camera Installation

Preparing the Camera

1. Rotate the bubble counterclockwise until it disconnects.

2. Pull the turret to remove it.

3. Rotate the camera counterclockwise until it disconnects from the skirt.

4. Set aside the bubble, turret, and camera.

Skirt

Camera

Turret

Bubble

Preparing the Mounting Surface

1. Mark the mounting surface for screw holes and wire access hole.

• Use the mounting template if you are surface mounting your camera. See

Mounting Template on page 65

• Use the flush mount adapter plate as a template if you are flush mounting your camera.

Figure 2-2 Mounting Template

Drill these holes for the mounting screws.

Cut this hole, then pull the power, audio, and alarm wires through it.

18


2. Pre-drill the holes as indicated on the template, using the recommended hole size for the screws being used.

Note Other fasteners (preferably stainless steel) can be used, provided they are not larger than the screw holes on the mounting template.

Connecting the Wires

Connecting Audio and Alarms

1. Pull the wires through the ceiling or wall hole until you have at least 4 inches of wire.

2. Remove the green connector strip (see

Figure 2-6 on page 22 ) from the camera base

and make all the necessary alarm and audio connections.

3. Connect a twisted pair (UTP) cable from each peripheral alarm contact to each alarm input on the terminal block.

Figure 2-3 Audio and Alarm PINs

Power 1 2 3 4 5

Table 2-1

6

7

4

5

8

2

3

PIN

1

Audio and Alarm Connector PIN Definitions

Definition

Audio In +

Audio In -

Audio Out +

Audio Out -

Alarm In +

Alarm In -

Alarm Out +

Alarm Out -

6 7 8

Connecting Audio

The network camera supports bi-directional audio. There are two supported voice band channels that function in full duplex mode. The camera can transmit audio from the camera to the client (PC) using any audio source that provides an industry standard line level input

(see the terminal strip as depicted in Figure 2-6

). The camera can also receive audio from


01/10

19

Installation and Setup the client (PC) and provide an industry standard line level output suitable to connect to audio devices. Audio input and output have 600 Ohm impedance. See Audio Settings on page 63 to configure audio options.

Connecting Alarms

WARNING!

Do not exceed the maximum rating of 12 VDC, 0.5 A on alarm output connections.

The HD3MDIP/X network camera has one alarm input and one alarm output. Connect mechanical or electrical switches to the alarm input connection to allow event-triggered recording. When alarm inputs are configured, the HD3MDIP/X triggers an alarm only when the normal alarm state (open or closed) changes.

Figure 2-4

Normally closed

Normal Alarm States

Normally opened

See Alarm Settings on page 62 to configure the alarm inputs.

Connect external devices such as sirens or flashing lights to the alarm output connector to signal an activated alarm to camera users.

Figure 2-5

Audio

Alarm Connection

Alarm

In Out

− +

+

−

The alarm output can be configured to provide normally open or normally closed contacts

(see Alarm Settings on page 62 to configure the alarm output). Contacts will be rated for 12

VDC @ 0.5 A.

4. Pull the cables through the back or side entries of the camera skirt, then connect the green connector strip to the camera assembly. You might have to remove the cover plate for flush mount.

20


Connecting Power

WARNING!

The use of a CSA Certified/UL Listed Class 2 power supply is required to ensure compliance with electrical safety standards.

Note Check the power source from the external power supply before applying power to the camera.

1. Connect the appropriate power supply for your installation:

•

24 VAC power supply (proceed to step 2

) or

• Power over Ethernet (IEEE 802.3af) 48 VDC power supply

Note If you are using PoE (802.3af), power will automatically be supplied to the camera through the network cable.

2. Connect to the power supply (see Figure 2-6 on page 22 ).

3. Plug the power supply into an appropriate power source. The LED on the RJ45 jack illuminates when the camera receives power. If it does not illuminate, check the terminal block connections and the power source.

Note To ensure satisfactory performance, it is recommended that you use a UPS source when connecting the camera to a 24 VAC power source.


01/10

21


Figure 2-6 Camera and Cables

RJ45 Ethernet network connection (using 10Base T or 100Base TX cable). See

Connecting to a Network via an RJ-45 Ethernet

Connector , page 23 )

Also for Power over

Ethernet (PoE 802.3af)

Factory reset button

Local video out connector

(for aim and focus)

24 VAC power

Figure 2-7 Wiring Connection Shown on Board

Connector Strip

Audio: Input/Output

Alarm: Input/Output

(see Connecting Alarms , page 20

)

RJ45 Ethernet Connector

(see

Connecting to a Network via an RJ-45 Ethernet

Connector , page 23

)

22


Caution Installation must be performed by a qualified electrician. The power wire size for the distance and the number of cameras must be determined to maintain 24 VAC at each camera.

Connecting to a Video Monitor

The local video out (see

Figure 2-7 ) is available as a test output and should be used as

needed during installation to position, aim, and focus the camera. Use the provided BNC connector to connect the video from the camera to the video input connector on your video monitor.

Connecting to a Network via an RJ-45 Ethernet Connector

The main video connection for your network camera will be made through your Ethernet network connection. Connect the Ethernet connector on your camera to your network using an Ethernet (10Base-T, 100Base-TX) cable.

Note You can connect your camera to a network or use any type of CAT5 cable to connect it directly to a PC or laptop.


01/10

23


Mounting the Camera

Surface Mount

1. Secure the skirt to the ceiling or wall using the appropriate screws (supplied).

2. Connect the wires (see

Connecting the

Wires on page 19 ).

3. Rotate and align the camera assembly yellow label with the skirt yellow label.

Skirt

Screws

(supplied)

Camera assembly

4. Secure the camera assembly to the skirt by pushing it into the skirt, then twisting it clockwise until it clicks securely in place.

5. Secure the camera assembly to the skirt by twisting it clockwise until it clicks securely in place.

Turret

Bubble

6. Adjust the camera’s field of view (see

Adjusting the Camera FOV (Field of View) on page 25

).

7. Install the turret by clicking it into place.

8. Install the bubble by placing it on the camera with the tabs to the left of the slots, then turning it clockwise until the tabs click securely into place.

24


Flush Mount (with or without 4S box)

4S box (not supplied and optional)

1. Use the screws (supplied) to connect the adapter plate directly to the ceiling or wall.

Or

Use your own screws to connect the adapter plate to the 4S box (not supplied) which is attached to the ceiling or wall.

Camera assembly

Adapter plate

Screws

(supplied)

Screw caps

2. Connect the wires (see Connecting the Wires on page 19

).

3. Secure the camera assembly to the adapter plate by twisting clockwise until it clicks securely in place.

Turret

Bubble

4. Adjust the camera’s field of view

(see

Adjusting the Camera FOV

(Field of View) on page 25 ).

5. Install the turret by clicking it into place.

Note Installation with 4S box shown

6. Install the bubble by placing it on the camera with the tabs to the left of the slots, then turning it clockwise until the tabs click securely into place.

Restore Factory Defaults

Your network camera has a Factory Reset switch located inside the camera (see

Figure 2-6 on page 22

). This switch restores your camera settings and passwords to their default settings. Press and hold the Reset switch for three seconds. This will reset the factory-configured parameters such as the compression settings, the camera tamper detection settings, and the Video Motion Detection settings. It will not impact network IP address configurations.

Adjusting the Camera FOV (Field of View)

To adjust the HD3MDIP/X camera:

1. Apply power to the camera and watch the video on a connected local video monitor

(see

Figure 2-7 on page 22 to connect a local video monitor).

2. Loosen the setscrew that locks the gimbal assembly in place (see Figure 2-8 ) to

adjust the horizontal rotation.


01/10

25


Setscrew (loosen to adjust horizontal rotation)

3. Adjust the gimbal assembly to the desired view.

4. Re-tighten the locking screw to lock the gimbal assembly in place.

Note Orient the camera as shown in

Figure 2-8 to maintain the correct picture

orientation.

Figure 2-8

Top view

Gimbal Adjustment

Angle view

Legend

A = Tilt rotation

B = Horizontal rotation

C = Pan rotation

Set focal length

(bottom)

Loosen set screw to adjust

Tilt Rotation (A)

Adjusting the Lens Focus

TECH TIP!

Lenses are pre-focused at the factory. They might require a final adjustment after installation because the optical effect of the bubble might cause a slight defocusing of the lens.

To check the focus, hold the bubble over the lens while making any adjustments.

To adjust the camera direction, view angle, and focus, connect the local video out to the video monitor using the supplied BNC video cable.

26


Securing the Enclosure Cover

Install the bubble when you have set up your camera and completed the network connections (see Chapter 3, Installing the Honeywell IP Utility and HD3MDIP/X Web-Client

Software ).

Place the enclosure cover on the camera with the tabs to the left of the slots, then turn it clockwise until the tabs click securely into place.

Figure 2-9 Installing the Enclosure Cover


01/10

27


28

Installing the Honeywell IP Utility and

HD3MDIP/X Web-Client Software

This chapter describes how to:

• Install and log onto the IP Utility

• Connect to a device and configure network settings using the IP Utility

• Launch the Web-Client software

• Uninstall the IP Utility, Bonjour, or ActiveX software

3

About the Honeywell IP Utility and Web-Client

About the Honeywell IP Utility

The Honeywell IP Utility is a software application that is installed from a CD or downloaded from the Honeywell Systems Group website ( www.honeywellvideo.com

). It is installed on a local workstation and primarily used by Administrators to configure the

EQUIP Series of products residing on an IP network.

The IP Utility enables users to:

• Discover device(s) on a network

• Configure the IP network settings, name device(s), upgrade firmware, change passwords.

• Open individual Web-Client applications for each discovered device.

Note Before installing and using the Honeywell IP Utility, confirm that your

HD3MDIP/X Network Camera is connected to the network through an

Ethernet cable (see Connecting to a Network via an RJ-45 Ethernet Connector on page 23 ).


01/10

29

Installing the Honeywell IP Utility and HD3MDIP/X Web-Client Software

About the Web-Client

The Web-Client is the web-based application that enables users to:

• View live-streaming video.

• View the device network settings and firmware details.

• Configure camera settings

• Configure video analytics settings.

• Configure compression settings.

• Configure alarm and audio settings.

User Profiles: Honeywell IP Utility and Web-Client

Both the Honeywell IP Utility and the Web-Client have two user types: Administrator and

Guest as described in

Table 3-1

.

Note Only one Administrator and only one Guest can be logged on at a time.

After the IP Utility software is installed, you can change the Administrator or Guest passwords.

Interface

Honeywell IP

Utility

Web-Client

Table 3-1

Administrator

User Profiles for Honeywell IP Utility and the Web-Client

• View the list of available network devices and connect to the devices.

• Configure the IP network settings.

• Upgrade firmware.

• Change the password to access the IP

Utility application.

• Change the access passwords to the

Web-Client application.

• View video and network settings.

• Configure compression settings.

• Configure camera setup.

• Configure video analytics.

• Configure audio and alarms.

Guest

•

•

•

View the list of devices available on the network.

View system settings including device name, IP address, and MAC address.

Guest users are limited to the Live View tab where they can view video

30


Step 1: Confirm Your System Requirements

Note Windows administrator privileges are required to install the Honeywell IP

Utility and associated software.

Note Contact the network administrator if there are any questions regarding the local area network (LAN) or any other network related issues.

Install the Honeywell IP Utility on a work station with the minimum requirements (outlined

in Table 3-2 ). After the IP Utility is installed, the same computer workstation can be used to

access the Web-Client.

Table 3-2

Component

Operating System

Processor

RAM

PC Minimum System Requirements

Requirement

Windows XP ® or WINServer 2003

Intel

®

Pentium

®

IV, 3.1 GHz or faster

1 GB RAM or higher

Table 3-3 Items Installed On Your System

Item

Honeywell IP Utility software

Bonjour software

HD3MDIP/X Honeywell IP

Adapter software

HD3MDIP/X Honeywell ActiveX software

EQUIP TM Series User Guides

Function

To enable use of the Web-Client to configure cameras and view live video.

To enable the devices to discover cameras on the network.

Required if a workstation does not have IP Utility installed but an operator is using the Web-Client.

To enable live streaming of video on the

Web-Client.

To provide detailed information about how to install and configure your EQUIP Series products.


01/10

31


Step 2: Install the Honeywell IP Utility Software

1. Close all other applications that might be open on your computer.

2. Open the Honeywell IP Utility InstallShield Wizard.

Method 1: CD

Insert the CD into the CD-ROM drive.

Note If InstallShield does not open automatically, navigate to [ CD

drive]\Honeywell IP Utility\Honeywell IP Utility Setup.exe. Double-click on the file to launch the program.

Method 2: Website a. Navigate to www.honeywellvideo.com. b. Click Customer Resources software downloads page.

➤ Download Center ➤ I Agree to reach the c.

Locate your device in the list (for example, click Cameras for HD3MDIP/X IP devices).

d. Under Honeywell IP Utility, download, extract and open the Honeywell IP Utility

Set-up.exe icon from where you extracted the file.

3. When the Honeywell IP Utility InstallShield Wizard opens, follow the instructions.

After the installation is complete, a Honeywell IP Utility icon displays on the desktop.

Downloading the EQUIP Series Installation Guides

1. To access the installation documents that were installed with the IP Utility, click Start

➤ All Programs ➤ Honeywell Video Systems ➤ EQUIP Series ➤ Manuals ➤

2. Select the applicable PDF to download to your computer.

Figure 3-1 Accessing Your Installation Documents

32


Step 3: Log Onto the IP Utility and Discover Network Devices

1. Double-click the Honeywell IP Utility icon

-OR-

Click Start ➤ Programs ➤

on your desktop.

Honeywell Video Systems ➤ EQUIP Series ➤ IP

Utility ➤ Honeywell IP Utility.

The Honeywell IP Utility Log On window opens.

Figure 3-2 Honeywell IP Utility Log On Window

2. Select Administrator or Guest from the User Name drop-down list.

3. Enter the case-sensitive password in the Password field.

• The default Administrator password is 1234.

Only one Administrator can be logged on at a time.

• The default Guest password is guest.

Note During the installation set up, you must log on as an Administrator to access all the features.

4. Click the arrow button .

The Honeywell IP Utility program searches for devices on the network and opens to the Honeywell IP Utility user interface.

5. Automatically discover or manually refresh the list of devices on the network.

Use the manual refresh if a new device was added after you logged onto the system.

• You do not need to do anything to discover devices. When you log on to the IP

Utility, the devices on the network — including the devices on other subnets — are automatically discovered and listed in the Discovery pane. After the initial discovery, the network automatically continues to discover devices that are newly added to the network.

• To manually refresh the device list, click the Refresh ( the top of the Discovery pane.

) button, located near

6. Enable or disable the HTTP Server checkbox for additional security. Only an

Administrator can disable (uncheck the box), resulting in the user being unable to access the Web-Client, although video recording is unaffected.


01/10

33


Refresh button

Disconnect button

Figure 3-3 Honeywell IP Utility User Interface

Connect button

Limited/No connectivity button

Use the Product Filter drop-down menu to select a specific device, such as all HD3MDIP/X cameras

The About menu displays the software version installed

From the User tab, Administrators can change the Web-Client user passwords

IP Network Setting assigns network settings automatically or manually

The Discovery pane lists the IP devices found on the network and groups by device type

Enable or disable HTTP

Server

Upgrade Firmware downloaded from the

Honeywell website

Launch Browser to open the

HD3MDIP/X IP Web-Client for each device

The Status bar displays how many devices are on the network, which one you are connected to, and which user is logged in.

Step 4: Connect to a Device and Configure Network Settings

When you log on to the IP Utility, the devices on the network—including the devices on other subnets—are automatically discovered and are listed in the Discovery pane. After the initial discovery, auto-refresh continues to discover devices that are newly added to the network.

34


You can also manually refresh the device discovery by clicking the Discovery icon ( ), located near the top of the Discovery pane.

Connecting to or Disconnecting From Devices

Before configuring the IP network settings, you must connect to the IP device.

Connecting to a Device

You can connect to individual Web-Client applications for each discovered device.

• In the Discovery pane, double-click the device to which you want to connect.

-OR-

• Select the device and click the Connect

The network settings for the connected device are displayed in the System pane.

Disconnecting from a Device

In the Discovery pane, select the device and click Disconnect .

Note If you disconnect the device without saving configuration details, a warning dialog box displays. Click Yes to save and disconnect, or click Cancel to discard the changes and disconnect the device.

Configuring the IP Network Settings Automatically or Manually

Note When you see the Limited/No connectivity button, you cannot fully connect to the device because the discovered device is on a different subnet from your PC. Check your network settings for both the device and your PC to resolve this issue. Consult your network administrator for additional support.

The IP network setting details, such as device name, IP address, and subnet mask can be configured for each connected device either automatically or manually.

Note It is important to click Apply to save any configuration change.


01/10

35


Option

Device Name

IP Address

Subnet Mask

Default Gateway

MAC Address

Table 3-4 IP Network Device Setting Options

Description

By default, the device name is the device type plus the MAC Address. Honeywell recommends, for security, that you change the device name.

The IP address of the device on the network.The camera obtains an IP address by static or dynamic (automatic) means. There are two options: DHCP (dynamic), assigned by the user, or APIPA (static), assigned by the network.

The subnet mask, or netmask, value of the device on the network. IP networks can be divided into several smaller networks by subnetting. When a network is subnetted, you must specify a subnet mask, which tells network devices which smaller network they belong to.

Note If the subnet mask is not properly configured, the camera might not be able to communicate with other devices on the network.

The default gateway address that connects the device to the network. Enter the

IP address of the host to use as a gateway between networks. The gateway allows communication between devices that are on different networks. Without a correct gateway setting, the camera cannot receive or transmit data from or to devices that are not in the same network address range.

The MAC address is a factory-assigned address that is unique for each device.

Figure 3-4 Set the IP Network Settings Automatically or Manually

Click to clear this checkbox and manually set the network details

36


Updating IP Network Settings Automatically

1. In the Discovery pane, select the device and click Connect .

2. From the System tab click the Obtain an IP Address automatically check box.

3. Enter a Device Name, for example, FrontLobbyDome01 .

4. Click Apply.

The network automatically assigns the IP Address based on the DHCP network server details. If no DHCP server is present on the network, the hardware defaults to an

APIPA address (169.254.x.x).

Updating IP Network Settings Manually

Caution When manually updating the network settings, it is important to enter the correct IP network settings before applying them. Incorrect values

might cause a failure when connecting to the device. See Table 3-4

for definitions of each setting.

1. In the Discovery pane, select the device, and click Connect .

2. To assign a static IP address to the device, from the System tab click to clear the

Obtain an IP Address automatically check box.

3. Enter a Device Name, for example, FrontLobby01.

Note The MAC address is a factory assigned address that is unique for each device.

4. Enter an IP Address of the device on the network.

Note The address must be in the same address range. For example, if the PC is

192.188.1.xx, then the device should be set to a similar address, for example

192.168.1.xy.

5. Enter the device Subnet Mask value. A value is required.

6. Enter a default Gateway Address that connects the device to the static network. A value is required.

7. Click Apply.

The network settings are updated and a message displays in the status bar to confirm the update.


01/10

37


Interfacing with the EQUIP Device Via a Network Video Recorder

Your recording vendor has the option of using either the connection methods supported by

EQUIP V1 firmware or EQUIP V2.1 firmware. If the NVR vendor has implemented EQUIP V1 connection methods, the HD3MDIP/X camera will work on those NVRs. Similarly, if the NVR vendor has implemented EQUIP V2.1 connection methods, the HD3MDIP/X camera will work on those NVRs. There is no user configuration necessary.

For further information, refer to the documentation supplied with your NVR or contact your

NVR network administrator.

Step 5: Launch the Web-Client to View Live Video

Note Only one Administrator and one Guest can log on to the Web-Client application at one time. After you are logged in as an Administrator, there is no time out until you click Logout. To allow other Administrators to log on, you must log out when the session is done.

Note After the IP Utility software is installed for the first time, you can change the

Administrator or Guest passwords and upgrade firmware.

Note It is important to click Apply in order to save any configuration change.

1. Log onto the Web-Client. There are two ways to launch the Web-Client and log on— via the Honeywell IP Utility Program or directly from Internet Explorer.

Honeywell IP Utility a. Log onto the Honeywell IP Utility program.

b. From the Discovery pane, click to select the device to launch its browser. c.

To enable or disable the HTTP server, select or clear the Enable HTTP Server check box. By default, the HTTP server is enabled.

d. From the System tab, click Launch Browser.

The Web-Client application for the selected device opens in Internet Explorer.

Internet Explorer

From Internet Explorer (v6.0+), enter the URL (IP address of the device) in the

Address bar to open the logon window.

38


2. Select a User Name and enter a Password.

a. From the User Name drop-down list, select Administrator or Guest.

b. In the Password field, enter the case-sensitive password.


• The default Guest password is guest. c.

Click .

3. A signed version of ActiveX® control is installed when you use the Web-Client to discover connected devices for the first time. If you have a previous version of IP

ActiveX is installed, you are prompted to upgrade to Honeywell secure ActiveX control.

Figure 3-5 ActiveX Prompt

Click Yes.

4. Follow the InstallShield Wizard prompts to install the secure Honeywell IP ActiveX on your PC.

5. The InstallShield Wizard Completed message indicates a successful ActiveX upgrade. Click Finish.

The Web-Client interface opens and live streaming video displays on the monitor.


01/10

39


Figure 3-6 Web-Client Interface After Logging On

Uninstalling IP Utility, Bonjour or the ActiveX Plug-in Software

You can uninstall the IP Utility, Bonjour, or IP ActiveX software using:

• The Start menu to uninstall IP Utility and Bonjour

OR

• The Control Panel to uninstall IP Utility, Bonjour and IP ActiveX.

40


Uninstalling IP Utility Using the Start Menu

1. Click Start

Utility ➤

➤ All Programs ➤ Honeywell Video Systems

Uninstall Honeywell IP Utility.

➤ EQUIP Series ➤ IP

2. Click Yes.

The Honeywell IP Utility is uninstalled.

3. During the uninstallation process, you are prompted to also uninstall the Bonjour program. Click Yes to remove Bonjour or No to only uninstall the Honeywell IP Utility.

4. Click Finish.

Uninstalling IP Utility or IP ActiveX Using the Control Panel

1. Click Start ➤ Settings ➤ Control Panel.

2. Open Add or Remove Programs and select Honeywell IP Utility or Honeywell IP

ActiveX from the Currently installed programs list.

3. Click Change/Remove.

The IP Utility Installation Wizard screen opens.

4. Click Next ➤ Remove.

The Honeywell IP Utility is uninstalled.

5. During the uninstallation process, you are prompted to also uninstall the Bonjour program. Click Yes to remove Bonjour or No to only uninstall the Honeywell IP Utility.

6. Click Finish.


01/10

41


42

4

IP Camera Web-Client

Before you launch the Honeywell IP Web-Client, ensure that you complete the following sections before configuring your HD3MDIP/X camera:

• Chapter 2, Installation and Setup

• Chapter 3, Installing the Honeywell IP Utility and HD3MDIP/X Web-Client Software

This chapter covers:

• Navigating the Web-Client interface

• Understanding the Web-Client features and functions

• Configuring compression settings

• Configuring camera settings

• Setting tamper detection

• Configuring audio and alarm settings

Overview

The network camera Web-Client is a web-based application that enables you to view video, listen to audio, and configure camera, sabotage detection, motion detection, alarm, and audio settings for the network camera.

Certain features of the IP Camera Web-Client are user-based and are available only to the

Administrator. The guest user is limited to the Live View tab. Only one Administrator and one Guest can be logged on at a time.


01/10

43

IP Camera Web-Client

User Profiles

Table 4-1 describes the roles and privileges for the HD3MDIP/X Web-Client application

users:

Table 4-1 User Roles and Privileges

User Role

Administrator

Privileges

• View video and network settings

• Configure the alarm and audio settings

• Set up the video compression settings

• Configure auto exposure and white balance for the camera

• Set up camera sabotage and video motion detection settings

Note Only 1 Administrator can be logged on at a time

Guest Operator • View video

Only 1 Guest can be logged on at a time

Logging On and Off the HD3MDIP/X IP Web-Client

Note One Administrator and one Guest can log on to the Web-Client application at a time.

There are two ways to open each HD3MDIP/X IP Web-Client.

• By clicking Launch Browser from the IP Utility interface.

• Directly from Internet Explorer by entering the URL (the IP address) in the address bar.

Note The web page where you log on to the Honeywell IP Utility and any IP device web page (for example, the HD3MDIP/X IP Web-Client) look very similar. You can tell the difference between the two sites by the IP address in the web browser as well as the program name in the lower left corner of the window.

44


Launching the Web-Client from IP Utility

1. From the desktop, double-click the Honeywell IP Utility icon

-OR-

Click Start ➤ All Programs ➤ Honeywell Video Systems ➤

.

EQUIP Series ➤ IP

Utility ➤ Honeywell IP Utility.

The Honeywell IP Utility Log On window opens.

2. From the User Name drop-down list, select Administrator or Guest.

See Table 4-1 on page 44 for User roles and privileges.

3. In the Password field, enter the case-sensitive password.


Only one Administrator can be logged in at a time.

• The default Guest password is guest.

4. Click .

The Honeywell IP Utility program searches for devices on the network and opens to the Honeywell IP Utility user interface.

5. In the Discovery pane, double-click the device you want to connect to.

-OR-

Select the device and click Connect .

The network settings for the connected device are displayed in the System pane.

6. Click Launch Browser (see Figure 4-1

) to go to the HD3MDIP/X Web-Client logon page.

Figure 4-1 Launching the HD3MDIP/X Web-Client from IP Utility

Connect to the device then click

Launch Browser


01/10

45


Logging Onto the Web-Client from Internet Explorer

1. From Internet Explorer (v6.0+), enter the URL (IP address of the device) in the

Address bar to open the logon window.

The Web-Client log on page opens.

2. Select a User Name and enter a Password.

a. From the User Name drop-down list, select Administrator or Guest.

b. In the Password field, enter the case-sensitive password.


• The default Guest password is guest. c.

Click .

3. The Web-Client interface opens and live streaming video displays on the monitor.

Logging Out of the Web-Client

Note After you are logged onto the HD3MDIP/X Web-Client there is no time out until you click Logout. To allow other Administrators to log on, you must log out when the session is done.

To log out from the Web-Client application, click Logout at the top of the Web-Client window.

46


Note Do not use the CLOSE button ( )in Internet Explorer to logout or the session might not end correctly, and settings that have you changed might not be saved.

Navigating the User Interface

Figure 4-2 Web-Client Window Layout: Administrator Log On

The URL corresponds to the HD3MDIP/X IP

Address as configured in the IP Utility.

Click Logout to exit the program.

Confirm the user type logged in.

If logged on as a Guest, only the Live

View tab is available. Administrators can access all tabs.

Click the tabs to access the available configurations and settings.

The image from the

HD3MDIP/S camera displays on every tab.

Each tab has a section for configuration and/or navigation controls.


01/10

47


The HD3MDIP/X Web-Client application user interface consists of multiple user-friendly views organized by function. Access to the views is user-controlled.

Table 4-2

Camera Setup

Video Analytics

Alarm and Audio

Tabs/Views in the Web-Client Application

Tab

Live View

Device Information

Compression

Settings

Enables you to...

View video.

View the network settings and firmware details of the camera.

Configure the compression.

Set the maximum bit rate and/or target bit rate that the camera will provide across the network based on priority mode settings. This value is the threshold that you do not want the bit rate to exceed.

View received bit rate and frame rate statistics of the current image in real time.

Configure auto exposure and white balance for the camera.

Configure the camera sabotage detection settings and view video display.

Configure the alarm and audio settings.

Figure 4-3 Web-Client: Administrator User

Click to select the video stream.

Click a Tab to display the corresponding view.

Screens are divided between displaying current video and the configuration options associated with the view.

The menu bar displays which user is logged on and provides a link to log out of the application.

48


Figure 4-4 Web-Client: Guest User

Logging on as a Guest limits users to Live View tab functions only.

See

Live View for more details.

When an alarm is detected, an alarm message appears here to notify an operator.

Live View

Live View shows live video from the selected camera (see

Figure 4-4

).

Device Settings

The Device Settings tab allows you to view the network settings and firmware details of the camera.


01/10

49


IP and Firmware Settings on the Device Information Tab

Depending on the hardware installation, there is a tab called either Device Information or

Device Settings. In both cases, the IP and Firmware Settings panel mirrors the information available in the Honeywell IP Utility. It provides read–only network settings, firmware settings, and video formats without having to access the IP Utility.

The Device Settings are the same for the Primary and Secondary streams.

Figure 4-5 Device Settings

50


Figure 4-6 IP and Firmware Settings: Device Information Tab

Device Name as entered in the

IP Utility program

IP Address on the network

(DHCP/Static/APIPA)

Subnet Mask and Default Gateway address that connects the camera to the network

MAC Address is a factory assigned address unique for each device

Firmware Settings including product name and version

Video Format - NTSC or PAL

Compression Settings

The video signal sent from the camera to the Web-Client has a number of settings that can be edited which affect how the video displays in the Web-Client. The Compression Settings view enables you to configure these settings:

• Stream Type

• Resolution

• Frame Rate

• Priority (Quality or Bite Rate)

• Compression Ratio (if Quality is chosen as the priority)

• Target Bit Rate (if Bit Rate is chosen as the priority)

• Maximum Bit Rate that the camera will provide across the network

• GOP (number of frames)


01/10

51


Figure 4-7 Compressions Settings Tab: Primary Stream

Your HD3MDIP/X camera provides dual simultaneous video streams. Although the Primary stream can support a single MPEG4 SP in real time 30 fps at 720p resolution, it must be set to less than 720P for the second stream to operate. The Secondary stream operates at a lower frame rate than the Primary stream.

Video Codec Settings Tab

Primary Stream

Default settings shown

Figure 4-8 Video Codec Settings Tab Available Functions

Secondary Stream

Set the Resolution for NTSC or

PAL video signals

Set the Frame Rate (the number of frames displayed on screen per second)

Set the Priority for Quality or Bit

Rate

Set the Compression Ratio (when

Quality is selected)

Set the Target Bit Rate (the amount of data processed per second)

Set the Maximum Bit Rate (kbps)

Set the GOP (Group of Pictures)

Default settings shown

52


Configuring the Compression Settings

1. On the Compression Settings tab, in the Statistics area, select the Received check box to receive in real time the bit rate and frame rates for the current image.

Deselecting the check box disables the refresh rate.

Note The Received check box is disabled by default. When you log out, this check box reverts to the disabled state.

Setting

Primary

Stream

Resolution

Secondary

Stream

Resolution

Frame Rate

Options

2. Use Table 4-3 to set up the video compression.

Table 4-3

HD (1280x720)

SVGA (800x600)

VGA (640x480)

QVGA (320x240)

VGA (640x480)

QVGA (320x240)

Compression Settings

Description

HD is the highest resolution; QVGA is the lowest resolution.

Up to 15 fps supported

Up to 20 fps supported

Priority

1–30 (NTSC)

1–25 (PAL)

The frame rate that is displayed per second. For NTSC, select from 1 fps (lowest) to 30 fps (highest). For PAL, select from 1 fps (lowest) to 25 fps (highest).

Quality, Bit Rate Allows you to set the maximum bit rate and/or target rate value, based on priority mode settings. This value is the threshold that you do not want the bit rate to exceed.

Select this Priority field setting

To enable this field … To achieve this …

Quality

(see Figure 4-9

)

Maximum Bit Rate

The Target Bit Rate field is grayed out.

If the target bit rate exceeds the maximum bit rate value, the camera adjusts the picture quality first and then, if necessary, drops frames to meet the maximum bit rate value.

Bit Rate

(see Figure 4-9

)

Target Bit Rate and

Maximum Bit Rate

The Picture Quality field is grayed out.

Set the Maximum Bit Rate—limit the data transfer speed—from 400 ~ 5000 kbps. As the target bit rate exceeds the maximum bit rate value, the camera reduces the bit rate by adjusting the frames dynamically to stay below the threshold that you set.

Compression

Ratio

Target Bit

Rate (kbps)

GOP (No. of

Frames)

Minimum, Low,

Medium, High,

Maximum

When Quality is selected as the Priority, select the Compression Ratio.

Minimum is the highest visual quality; Maximum is the lowest visual quality.

400 – 5000 kbps Enter the Target Bit Rate in kbps (kilobits per second) which represents the amount of data processed per second.

1– 60 Select the GOP (Group of pictures) number from 1 to 100. (Not available on the

Secondary Stream.)


01/10

53


Figure 4-9 Video Codec Settings, Quality Priority Selected

Set the Resolution for

NTSC or PAL video signals.

Statistics are received for the current image in real time when

Received is enabled.

3. Click Apply. Adjustments in your compression settings are captured in the statistics.

As you make adjustments, the Statistics field acts as a visual reminder of how your settings affect the bit rate, frame rate, and bandwidth usage.

4. When you are satisfied with your settings—that is, that the image quality and bandwidth usage meets your requirements—click Apply to save your settings.

Settings are not saved unless you click Apply.

Statistics: Received Bit Rate and Frame Rate

To view in real time the received bit rate and frame rate statistics of the current image:

1. Click the Compression Settings tab.

2. In the Statistics area, select the Received check box.

Deselecting the check box disables the refresh rate.

Note The Received check box is disabled by default. When you log out, this check box reverts to the disabled state.

54


Camera Setup

The Camera Setup view provides access to the settings used to configure the camera configurations for both Primary and Secondary streams. The following section explains

Auto Exposure and White Balance setup.

Note You must click Apply after you make changes to any settings to save those changes. Settings are not saved unless you click Apply.

Figure 4-10 Camera Setup

Auto Exposure

The camera lens, lighting, and true day/night options can be configured as needed using the Auto Exposure settings. Use

Table 4-4

to set up Auto Exposure options.


01/10

55



Setting

Table 4-4

Options

Auto Exposure Settings

Description

ALC (Automatic Light

Compensation)

DC Iris Level: 1–25 For an automatic iris lens. Adjust the DC Iris Level until the image is neither too bright nor too dark.

AGC (Automatic Gain

Control)

Off, 10 dB–40 dB Adjust the maximum value of AGC gain. AGC can be Off, or set to

20 dB, 30 dB, or 40 dB.

DNR (Digital Noise

Reduction)

Flickerless

Digital Slow Shutter

(DSS)

Day/Night

Night Mode

Detect Time

DayToNight

Off, On

Off, On

Off, Low, High

Auto, Day, Night

B/W or Color

5–60 seconds

1–7

Note As AGC levels are reduced, the threshold ranges for DayToNight and NightToDay are decreased.

Improves picture performance in low light by reducing video noise.

DNR is deactivated if AGC is turned Off.

Eliminates the “flicker” that can appear in an image under certain lighting conditions (for example, fluorescent lighting).

Automatically provides a clear image under low-light conditions

(increasing magnification may cause noise/distortion).

Set the moving mechanical IR filter within the camera to ensure true

24-hour surveillance.

Sets the color mode as B/W (monochrome) or Color in Night Mode.

Day/Night must be set to Night.

Sets the time (5–60 seconds) before the camera switches to Day or

Night mode after detecting a low-light condition.

Day/Night must be set to Auto.

Determines the low light detection level (1–7) when the camera switches to Night mode. The lower the value, the darker the lighting conditions before the camera switches.


NightToDay 3–9

Note The DayToNight threshold level must be set at least 2 less than the NightToDay threshold setting.

Note The DayToNight threshold range is decreased if the AGC level is reduced.

Determines the low light detection level (3–9) when the camera switches to Day mode. The higher the value, the brighter the lighting conditions before the camera switches.


Note The NightToDay threshold range is decreased if the AGC level is reduced.

56


White Balance

White Balance ensures that color integrity is maintained in the camera image by compensating for the temperature color “casts” that different light sources can cause. Use

Table 4-5 to set up White Balance options.


Table 4-5

Option

White Balance Settings

AWC Auto (Auto White

Balance Control Mode)

MWB (Manual Mode)

Description

A faster AWB mode with a wide operating range.

Manual white balance mode. Set the Red and Blue gains from 0–255.

AWC Push (Auto White

Balance Control Mode)

Automatically adjust the white balance to your specific environment. When selected, the white balance is locked.

Note This setting is recommended for situations in which the light conditions are constant, so that the specified color temperature does not change.

Video Analytics

The HD3MDIP/X camera can be configured to detect camera sabotage and motion within a scene via the Video Analytics view (see

Figure 4-11 ). The Video Analytics tab enables a

user to set the tamper detection threshold settings for blur, blinding and scene changes.


01/10

57


Figure 4-11 Video Analytics Tab

Each Tamper Detection

Setting provides 3 threshold levels: High

(80%), Medium (50%) and Low (30%).

Each setting has three threshold levels: high (80%), medium (50%) and low (30%). When these thresholds are exceeded, camera sabotage or motion is detected, and alarm messages appear above the video display and alarm signals are sent to DVRs/NVRs (see

Figure 4-13 ).

Sabotage Detection

Figure 4-12 Tamper Detection Settings on the Video Analytics Tab

Set the Blur Threshold. Blur can be affected by elements such as water, for example

Set the Blinding Threshold.

Blinding applies to obstacles in front of the camera lens

Set the Scene Change

Threshold

58


There are three types of sabotage detection in the Tamper Detection Setting tab on the

Video Analytics tab: blinding the camera, blurring the video display, and tampering with the camera field of view. The user should note that when the following conditions are applicable, the tamper detection features should be manually disabled to avoid raising false alarms:

• During the configuration of the video display

• While text is overlaid on the video

• If the video display becomes too dark

Figure 4-13 Video Analytics Alarm Message

Configuring Video Blur Detection

The video appears blurred when the camera is exposed to elements such as water. When this occurs, video blurring in the field of view is detected and an alarm message appears

(see

Figure 4-13

) above the video display. To detect video blurring:

1. Click the Video Analytics tab.

2. In the Blur Threshold list, select one of the following options:

Table 4-6

Value

High (80%)

Medium (50%)

Low (30%)

Blur Threshold Values

To detect …

Maximum video blurring. The alarm message appears when the video display is blurred by 80% or more.

Medium video blurring. The alarm message appears when the video display is blurred by 50% or more.

Minimum video blurring. The alarm message appears when the video display is blurred by 30% or more.

3. Click Apply.

Note To turn off video blur detection, select Disable in the Blur Threshold list.

Disable is the default value.



01/10

59


Configuring Camera Blinding Detection

An obstacle in front of the camera lens can blind the camera. When this occurs, camera blinding is detected and an alarm message appears above the video display (see

Figure 4-13 ). To detect camera blinding:


2. In the Blinding Threshold list, select one of the following options:

Table 4-7

Value

High (80%)

Medium (50%)

Low (30%)

Blinding Threshold Values

To detect …

Maximum blinding. The alarm message appears when the

HD3MDIP/X camera is blinded by 80% or more.

Medium blinding. The alarm message appears when the


Minimum blinding. The alarm message appears when the


3. Click Apply.

Note To turn off camera blind detection, select Disable in the Blinding Threshold list. Disable is the default value.


Configuring Camera Field of View Change Detection

The Web-Client application can detect tampering of the camera field of view and show an

alarm message above the video display (see Figure 4-13 ). To detect a camera field of view

change:


60


2. In the Scene Change Threshold list, select one of the following options:

Table 4-8

Value

High (80%)

Medium (50%)

Low (30%)

Scene Change Threshold Values

To detect …

Maximum change in the camera field of view. The alarm message appears when tampering causes at least an 80% change in the HD3MDIP/X camera field of view.

Medium change in the camera field of view. The alarm message appears when tampering causes at least a 50% change in the HD3MDIP/X camera field of view.

Minimum change in the camera field of view. The alarm message appears when tampering causes at least a 30% change in the HD3MDIP/X camera field of view.

3. Click Apply.

Note To turn off camera field of view change detection, select Disable in the Scene

Change Threshold list. Disable is the default value.


Configuring Video Motion Detection

For motion detection, an Administrator can enable and configure up to 5 zones within a scene. The enabled and configured zones will be monitored for motion.

1. Click the Region drop-down menu, then select a region from the five available.

2. Click the VMD drop-down arrow, and select Enable.

The Regions appear in their default positions.

3. Click Apply.

4. Click and drag the box to resize and place it over the camera image.

5. Select the sensitivity level (High, Medium, Low).


01/10

61


Figure 4-14 Video Analytics: Defining a Region

Region-defining box

Note To disable a zone, click the VMD drop-down menu, then select Disable.

Alarm and Audio

Alarm Settings

Connect external devices such as sirens or flashing lights to the alarm output connector to signal users of the camera that an alarm is activated. Set the Alarm Output as Normally

Open or Normally Close. See Connecting Alarms on page 20 for more information.

When alarm inputs are connected, the camera triggers an alarm only when the normal state

(open or closed) changes. An alarm message appears on the Web-Client screen (see

Figure 4-13 ) to notify the operator.

62


Audio Settings

The network camera supports bi-directional audio. There are two supported voice band channels that function in full duplex mode. Connect industry-standard line level audio input and output to the back of your camera. See Connecting Alarms on page 20 for more information.

Audio configuration for your network camera is straightforward.

Figure 4-15 Audio Settings

To listen to or capture audio from the camera, enable the Camera to Client (PC) check box

( ). To listen to audio from the client (PC), enable the Client (PC) to

Camera check box.


01/10

63


64

Mounting Template

HD3DIP/X Mounting Template

Apply to clean, dry surface, free of dust and dirt

6 Holes

Use recommended drill bit as per screws (supplied)

A


01/10

65

Mounting Template

66

B

Troubleshooting

Technical Support

Prior to calling Honeywell technical support, refer to the following topics for possible solutions to problems with your HD3MDIP/X camera. To contact the Honeywell Video

Systems technical support team, call 1-800-796-2288 (North America only) or send an e-mail to [email protected]

.

Any equipment returned to Honeywell Video Systems for warranty or service repair must have a Return Merchandise Authorization (RMA) number. The RMA number must be clearly marked on all return packages and internal paperwork.

Problem: Lens Out of Optical Focus

Possible solutions:

1. Verify that the lens cap has been removed from the camera.

2. This can also be caused by dirt, oil, grease, and fingerprints, and so on, that have accumulated on the lens or bubble. Check the lens and bubble, then clean them, if needed.

Caution Use extreme caution when cleaning the lens and bubble so you do not scratch their optical surfaces. Prepare a washed-out cotton cloth or lens cleaning paper with alcohol or lens cleaning liquid. Clean by moving spirally from the lens center towards its rim. Repeat until the lens is completely clean.


01/10

67

Troubleshooting

Problem: Live View Does Not Display the Expected Video

Possible solutions:

• Ensure that your web browser settings have been configured to allow ActiveX controls

(see Installing the Honeywell IP Utility and HD3MDIP/X Web-Client Software on page

29 for information on setting up your browser).

• Ensure that the network cable from the camera is connected to both the camera and the network.

• Ensure that the camera assembly board DIP switch settings are configured correctly.

Problem: Cannot Connect to a Device

When the following message (

Figure B-1 ) displays in the status bar of the IP Utility, your

device connection is limited. Usually this warning indicates that your PC and the device your are connecting to are on different subnets. Contact your network administrator for help to resolve your network issue(s).

Figure B-1 Limited or No Connection Message

68

C

Specifications

Note These specifications refer to all models, except where otherwise noted.

Specifications are subject to change without notice.

Video Signal Specifications

Scanning System:

Image Sensor:

Number of Pixels (H x V):

Minimum Illumination:

Video Output (local):

S/N Ratio:

Auto Gain Control (AGC):

Auto Electronic Shutter (ELC):

Automatic Lens Iris Control:

White Balance (AWB):

Lens Type:

Audio Signal Specifications

Audio/Two-Way

Electrical Specifications

Input Voltage:

Input Voltage Range:

Surge Suppression

Power Consumption:

Mechanical

Dimensions (WxH):

Weight:

Construction:

Connectors:

NTSC PAL

Progressive

1/4” CMOS

1280 x 720

1.0 lux color @ 50 IRE, F1.2

1.0 Vp-p @ 75 Ohms

50 dB or more (AGC Off)

Off/On, selectable (20 – 40 dB)

1/60 – 1/100,000 sec 1/50 – 1/100,000 sec

DC Iris level 1 – 25

AWC, MWB (Manual Mode), AWC Push

3.3 mm to 12.0 mm Vari-focal Auto Iris, F1.6

Line in/out

24 VAC, PoE IEEE 802.3af

17 – 28 VAC

1.5 kW transient

5 W (max)

See diagrams (

Figure C-1

,

Figure C-2

,

Figure C-4 ,

Figure C-4 )

1.5 lb (0.68 kg) camera only

Housing: Polycarbonate

Finish: Matte texture, Off-white

Local Video Output: 2-pin Molex connector

Power Input: Removable screw block

Alarm I/O: Removable screw block

Audio I/O: Removable screw block

Network: RJ45 connector


01/10

69

Specifications

Environmental

Temperature:

Relative Humidity:

IP Specifications

Video Compression:

Resolutions:

Software Update:

Frame Rate NTSC/PAL:

Video Streaming:

Security:

Users:

Video access from web browser:

Minimum web browsing requirements:

Installation, Management, and

Maintenance:

Supported Protocols:

Operating: 14°F to 122°F (-10°C to 50°C)

Storage: -4°F to 140°F (-20°C to 60°C)

0% to 85%, non-condensing

MPEG-4, MJPEG

HD:

SVGA:

VGA:

QVGA:

1280 x 720

800 x 600

640 x 480

320 x 240

Field Upgradeable

Up to 30/25 fps video in all resolutions

Dual Streaming: MPEG-4 and MJPEG

Controllable frame rate and bandwidth

Constant or variable bit rate (MPEG-4)

Multiple user access levels with password protection

1 Administrator; 1 Guest

Camera live view for 1 client. Full control of all camera settings available to administrator

Pentium IV CPU 3.1 GHz or equivalent AMD

1 GB RAM

Windows® 2003/XP

Honeywell IP Utility software identifies the IP address, checks the status of the device. Firmware upgrades over

HTTP, firmware available at www.honeywellvideo.com

.

HTTP, TCP, RTSP, RTP, UDP, ARP, DNS, RTCP, FTP,

ICMP, DHCP, Bonjour, IGMP, Telnet

Regulatory

Emissions:

Immunity:

Safety:

Mounts

HD3MDIP-PK

HD3MDIP-WK

EN55022

EN 50024

EU: 2006/95/EC LVD; UL 60950

Pendant mount bracket

Wall mount bracket

Figure C-1 HD3MDIP/X Side View with Dimensions

4.9” (125.1 mm)

70


Figure C-2 HD3MDIP/X Side View Dimensions without Skirt

3.9” (97.7 mm)

Figure C-3 HD3MDIP/X Side View Dimensions with Adapter Plate

6.4” (161.5 mm)


01/10

Figure C-4 HD3MDIP/X Bottom View with Dimensions

3.50

3.2

” (82.5 m m)

” (89.0 m m)

∅ 2.88”

(73.10 mm)

1.

” 8

(4

6.

0 m m

)

4.9” (125.1 mm)

71

Specifications

72

D

Glossary

AGC (Automatic Gain Control) Video Amplifier in a camera that boosts the amount of video gain (including the noise) to maintain a 1V p-p (1-volt peak-to-peak) video signal output. It becomes operational when the light level is low. The circuit is designed to compensate for fluctuations in scene illumination which would cause the video output level to be too low. If the video level (scene illumination) is adequate, the circuit does not apply any gain to the signal. As the video level falls, more gain is applied by the AGC circuit to the video signal.

ALC (Automatic Light Compensation) Setting in an Auto Iris lens to control the iris opening. Adjusts between peak and average to respond to the bright part of the scene

(peak setting) or the average value of the video signal (average setting).

DHCP (Dynamic Host Configuration Protocol) Allows a server to dynamically assign

IP addresses to nodes (workstations) automatically. Provides client information including subnetwork mask, gateway address, and DNS (Domain Address Server) addresses.

DNR (Digital Noise Reduction) Digital Noise Reduction eliminates the “flicker” that can appear in an image under certain lighting conditions (for example, fluorescent lighting).

DSS (Digital Slow Shutter) Automatically provides a clear image under low-light conditions (increasing magnification may cause noise/distortion).

Flickerless Eliminates the “flicker” that can appear in an image under certain lighting conditions (for example, fluorescent lighting). This is usually caused by the interaction of the shutter with the AC frequency of the lighting. The flickerless setting changes the camera shutter speed to a value that will not cause flicker (1/100 sec, NTSC, 1/120 sec for PAL). The side effect is that the camera sensitivity is reduced because the electronic iris feature has effectively been turned off and will no longer control the optimum exposure setting for available light conditions.

FOV (Field of View) The part of the scene visible with a particular lens. The height

(horizontal) and width (vertical) picture size at a given distance that can be seen through a lens. Generally, shorter focal length lenses have a wider field of view than those with longer focal lengths.

Gain The amplification a system provides to a signal.

IP Address A unique, 32-bit identifier for a specific TCP/IP host computer on a network.

Iris Adjust Adjusts the iris to either open or close in response to changing light conditions.

NTSC (National Television Standards Committee) A standard of specifications for television transmission in the U.S., Canada, Japan, Central American, and half of South

America. The North American system uses interlaced scans and 525 horizontal lines per frame at 30 frames per second.


01/10

73

Glossary

PAL (Phase Alternate Line) A standard of specifications for television transmission for color TV signals used in West Germany, England, Holland, Australia, and several other countries. It uses an interlaced format with 625 lines per frame at 25 frames per second.

PoE (Power over Ethernet) A system designed to transmit electrical power, along with data, to remote devices over a standard twisted pair cable in an Ethernet network.

Shutter Speed The speed at which the charge is read out from the CCD chip. Adjusts the light sensitivity of the camera. A faster (briefer) shutter speed can arrest the motion of a fast moving object (reduce image blur), rendering it sharp. Fast shutter speeds allow less light to all on the CCD and can darken the image. For fast shutter speeds, ensure there is adequate lighting. Usually selected using DIP switches on the side of the camera.

Subnet Mask A number used to identify a subnetwork so that an IP address can be shared on a LAN.

True Day/Night The incorporation of a moving mechanical IR filter within the camera ensures true 24 hour surveillance, providing high quality color images during the day and similar quality black & white images at night when used with IR lighting.

74


Index

A

ActiveX control

39

administrator privileges

30

administrator password, default

33

AGC (Automatic Gain Control)

56

AGC (automatic gain control)

56

alarm configuration

62

alarm output settings

62

alarm settings

62

alarms, connecting

20

ALC (automatic light compensation)

56

APIPA address

36

,

37 ,

51

audio connections

19

audio configuration

63

audio connections

19

audio settings

63

auto configuration, IP network

35

– 37

device discovery

33

,

37

log out, IP Utility

38

auto exposure settings

55

Auto White Balance Control mode

57

Automatic Gain Control

56

Automatic Light Compensation

56

AWC (auto white balance control mode)

57

B

bit rate

52 ,

53

setting

51 ,

53

viewing statistics

54

blinding threshold

57

,

60

blur threshold

57 ,

59

Bonjour software

31

C

cabling, connecting

21


01/10 camera adjusting

25

components

17

installation

18

type

50

camera blinding

60

camera components

17

camera field of view change

60

camera settings

AGC

56

ALC

56

AWC

57

DayToNight

56

detect time

56

flickerless

56

MWB

57

NightToDay

56

CAT5 Ethernet connector

23

cautions

10

,

21

compliance

10

components, camera

17

compression ratio, setting

51

compression settings

51 ,

52

bit rate

53

frame rate

53

GOP (group of pictures)

53

maximum bit rate

53

picture quality

53

primary stream resolution

53

secondary stream resolution

53

target bit rate

53

configuration alarm

62

audio

63

configuring

IP network settings

35

–

37

connect button

34

connecting to devices

35

,

45

connections alarms

20

audio

19

75

audio, alarm

19

CAT5 Ethernet

23

video monitor

23

customer service

11

D

DayToNight

56

declaration of conformance

11

default passwords

33

default gateway

36

defaults, restore factory

25

device connecting

35

disconnecting

35

discovering

33

,

37

information tab

50

name

36

DHCP address

36

,

37

,

51

digital noise reduction

56

digital slow shutter

56

disconnect button

34

disconnecting, from IP Utility

35

DNR

56

DSS

56

E

EQUIP series manuals

32

F

factory defaults, restoration

25

features, camera

13

field of view adjustment

25

field of view change

60

field of view, adjusting

25

finding installed user manuals

32

firmware settings

50

upgrading

34

flickerless

56

frame rate

52

,

53

setting

51

viewing statistics

54

functions, camera

17

G

gateway

36 ,

51

GOP (group of pictures)

52

,

53

group of pictures (GOP)

53

76 guest password, default

33

guest user privileges

30

H

HTTP server

33

I

installation mounting template

65

installation procedure

16

installation steps

16

installed components

31

installing the camera

18

IP address

36 ,

37 ,

51

APIPA

36

DHCP

36

network settings

35 –

37

,

50

IP address

36

IP network settings

35

default gateway

36

IP address

36

MAC address

36

subnet mask

36

IP Utility description

29

disconnecting

35

discovering devices

33

,

37

installing

32

interface overview

34

logging on

33

logging out

38

uninstalling

41

user types

30

web-client and

38

,

45

IP Utility, logging onto

33

L

LAN

31

launch web-client

34 ,

38 ,

45

launching an IP Web-Client

44

launching the IP Utility

33

lens adjustment

26

lens focus, adjusting

26

limited/no connectivity button

34

,

35

line lock, adjusting

26

live view tab layout

47

log off from the IP Web-Client

46

logging onto an IP Web-Client

44

logging onto the IP Utility

33

M

MAC address

36

,

37

,

51

manual white balance mode

57

manual, configuration, IP network

35

– 37

maximum bit rate

53

maximum bit rate, setting

51

motion detection

61

mounting template

18 ,

65

mounting, template

18

MWB (manual white balance) mode

57

N

netmask

36

NightToDay

56

normally closed

20

normally open

20

NTSC video format

51

video resolution

52

NTSC, video resolution

54

O

opening an IP Web-Client

44

operating system

31

P

PAL video format

51

video resolution

52

PAL, video resolution

54

password defaults

33

picture quality

52

,

53

power, connecting

21

primary stream resolution

53

priority

51

priority order quality or bit rate

52

processor

31

profiles, user

30

Q

quality

53

quality priority setting

54

R

RAM

31


01/10

HD3MDIP/X Network Camera Reference Guide refresh button

34

resolution

52

resolution, setting

51

S

scene change threshold

57

,

60

secondary stream resolution

53

security settings, ActiveX

39

service

11

setting

IP network

34

settings alarm

62

audio

63

auto exposure

55

software downloading from website

29

,

32

installing

31

,

32

uninstalling

41

version

34

software updates

15

start menu

31

statistics frame rate

54

received bit rate

54

statistics, viewing bit rate

54

statistics, viewing frame rate

54

subnet mask

36

,

51

system requirements

31

T

tamper detection

59

target bit rate

52 ,

53

target bit rate, setting

51

technical support

67

template, mounting

18

thresholds, video analytics

57

troubleshooting

67

U

uninstalling, software

41

update user manuals

15

updates, software

15

upgrading firmware

34

user manuals, hot to update

15

user manuals, how to find installed

32

user profiles

30

V

video

77

analytics tab

57

format

51

viewing live

47

video analytics

57

blinding threshold

60

blur threshold

59

camera blinding

60

field of view change

60

motion detection

61

sabotage detection sabotage detection

58

scene change threshold

60

tamper detection

59

video blurring

59

video blurring

59

video monitor, connecting

23

video motion detection

61

VMD

61

W

warnings

10 ,

21

warranty

11

web browser

31

web client compression settings

51

web-client description

30

launching and logging on/off

38

user types

30

website

29

,

32

wiring alarm connection

20

connections on board

22

78

Honeywell Security Group (Head Office)

2700 Blankenbaker Pkwy, Suite 150

Louisville, KY 40299, USA www.honeywellvideo.com

℡ +1.800.796.2288

Honeywell Security Group Europe/South Africa

Aston Fields Road, Whitehouse Industrial Estate

Runcorn, Cheshire, WA7 3DL, UK www.honeywell.com/security/uk

℡ +44.01928.754028

Honeywell Security Group Caribbean/Latin America

9315 NW 112th Ave.

Miami, FL 33178, USA www.honeywellvideo.com

℡ +1.305.805.8188

Honeywell Security Group Pacific

Level 3, 2 Richardson Place

North Ryde, NSW 2113, Australia www.honeywellsecurity.com.au

℡ +61.2.9353.7000

Honeywell Security Group Asia

35F Tower A, City Center, 100 Zun Yi Road

Shanghai 200051, China www.asia.security.honeywell.com

℡ +86 21.5257.4568

Honeywell Security Group Middle East/N. Africa

Post Office Box 18530

LOB Building 08, Office 199

Jebel Ali, Dubai, United Arab Emirates www.honeywell.com/security/me

℡ +971.04.881.5506

Honeywell Security Group Northern Europe

Ampèrestraat 41

1446 TR Purmerend, The Netherlands www.honeywell.com/security/nl

℡ +31.299.410.200

Honeywell Security Group Deutschland

Johannes-Mauthe-Straße 14

D-72458 Albstadt, Germany www.honeywell.com/security/de

℡ +49.74 31.8 01.0

Honeywell Security Group France

Immeuble Lavoisier

Parc de Haute Technologie

3-7 rue Georges Besse

92160 Antony, France www.honeywell.com/security/fr

℡ +33.(0).1.40.96.20.50

Honeywell Security Group Italia SpA

Via della Resistenza 53/59

20090 Buccinasco

Milan, Italy www.honeywell.com/security/it

℡ +39.02.4888.051

Honeywell Security Group España

Mijancas 1. 3a planta

P.Ind. Las Mercedes

28022 Madrid, Spain www.honeywell.com/security/es

℡ +34.902.667.800

www.honeywellvideo.com

+1.800.796.CCTV (North America only)

[email protected]

Document 800-04132V1 – Rev A – 01/10

© 2009 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.

No results