advertisement
HD3MDIP/X Network Camera Reference Guide
Figure 4-4 Web-Client: Guest User
Logging on as a Guest limits users to Live View tab functions only.
See
When an alarm is detected, an alarm message appears here to notify an operator.
Live View
Live View shows live video from the selected camera (see
).
Device Settings
The Device Settings tab allows you to view the network settings and firmware details of the camera.
Document 800-04132V1 Rev A
01/10
49
IP Camera Web-Client
IP and Firmware Settings on the Device Information Tab
Depending on the hardware installation, there is a tab called either Device Information or
Device Settings. In both cases, the IP and Firmware Settings panel mirrors the information available in the Honeywell IP Utility. It provides read–only network settings, firmware settings, and video formats without having to access the IP Utility.
The Device Settings are the same for the Primary and Secondary streams.
Figure 4-5 Device Settings
50
advertisement
Related manuals
advertisement
Table of contents
- 9 Overview of Contents
- 10 Cautions and Warnings
- 10 FCC Compliance Statement
- 11 Manufacturer’s Declaration of Conformance
- 11 North America
- 11 Europe
- 11 Warranty and Service
- 13 Features
- 15 Before You Begin
- 15 Unpack Everything
- 16 Equipment Required
- 16 Overview of Installation Procedure
- 17 Camera Components and Functions
- 18 Camera Installation
- 18 Preparing the Camera
- 18 Preparing the Mounting Surface
- 19 Connecting the Wires
- 24 Mounting the Camera
- 25 Restore Factory Defaults
- 25 Adjusting the Camera FOV (Field of View)
- 26 Angle view
- 26 Adjusting the Lens Focus
- 27 Securing the Enclosure Cover
- 29 About the Honeywell IP Utility and Web-Client
- 29 About the Honeywell IP Utility
- 30 About the Web-Client
- 30 User Profiles: Honeywell IP Utility and Web-Client
- 31 Step 1: Confirm Your System Requirements
- 32 Step 2: Install the Honeywell IP Utility Software
- 32 Downloading the EQUIP Series Installation Guides
- 33 Step 3: Log Onto the IP Utility and Discover Network Devices
- 34 Step 4: Connect to a Device and Configure Network Settings
- 35 Connecting to or Disconnecting From Devices
- 35 Configuring the IP Network Settings Automatically or Manually
- 38 Interfacing with the EQUIP Device Via a Network Video Recorder
- 38 Step 5: Launch the Web-Client to View Live Video
- 40 Uninstalling IP Utility, Bonjour or the ActiveX Plug-in Software
- 41 Uninstalling IP Utility Using the Start Menu
- 41 Uninstalling IP Utility or IP ActiveX Using the Control Panel
- 43 Overview
- 44 User Profiles
- 44 Logging On and Off the HD3MDIP/X IP Web-Client
- 45 Launching the Web-Client from IP Utility
- 46 Logging Onto the Web-Client from Internet Explorer
- 46 Logging Out of the Web-Client
- 47 Navigating the User Interface
- 49 Live View
- 49 Device Settings
- 50 IP and Firmware Settings on the Device Information Tab
- 51 Compression Settings
- 52 Video Codec Settings Tab
- 54 Statistics: Received Bit Rate and Frame Rate
- 55 Camera Setup
- 55 Auto Exposure
- 57 White Balance
- 57 Video Analytics
- 58 Sabotage Detection
- 61 Configuring Video Motion Detection
- 62 Alarm and Audio
- 62 Alarm Settings
- 63 Audio Settings
- 67 Technical Support
- 67 Problem: Lens Out of Optical Focus
- 68 Problem: Live View Does Not Display the Expected Video
- 68 Problem: Cannot Connect to a Device