Muton VJ-1626UH Installation manual

VJ-1626UH INSTALLATION MANUAL
Please read this manual
before using
Thank you for purchasing a MUTOH product.
This manual explains the steps for unpacking,
mounting and basic installation before using the
MUTOH Full-color inkjet printer VJ-1626UH.
3 Assembling
5 Connecting the power cable
3.1 Assembling the stand
‫ޓ‬
3.2 Attaching the stand
‫ޓ‬
This manual is intended for owners, installers, and
users of this product.
Understand the contents and instructions in this
manual before installing this product.
6 Turning the power ON/OFF
Installation flow chart
The broad steps for installation are shown below.
There are instructions for each section beginning on
the next page.
Media Type
1 Unpacking boxes
1.1 Unpacking the printer box
Heater Link
Roll
Origin
Rigid
3.3 Detaching fastening materials
Long Feed
7 Product activation
8 Initial ink filling‫ޓ‬
3.5 Assembling the Media-feed table
(optional)‫ޓ‬
1.2 Unpacking the stand box and
the Media-feed table F and R
boxes
‫ޓ‬
9Loading media
9.1 Loading rigid media
4 Installation
4.1 Installation environment
2 Confirming bundled items
4.2 Installation procedure
9.2 Loading roll media
2.1 Items in the printer box
2.2 Items in the accessory box
2.3 Items in the stand box
2.4 Items in the Media-feed
table(optional) box
10 Checking the printing condition
11 Manual composition
1
VJ1626UHE-I-00
VJ-1626UH INSTALLATION MANUAL
1 Unpacking boxes
2 Confirming bundled items
Procedures for unpacking boxes are explained.
After unpacking, please confirm that the product has
not damaged and no components are missing.
This printer package consists of four boxes: Main
body, Stands, and Media-feed table (two separate
optional boxes).
2.3 Items in the stand box
1
3
NOTE
If any items are damaged or missing, contact
MUTOH local dealer.
CAUTION
Make sure to unpack this product with
four persons or more.
While taking out the printer from the box,
make sure to remove the vinyl sheet.
4
2.1
5
Items in the printer box
1
6
1.1
2
8
7
9
Unpacking printer box
Unpack the printer box in accordance with the following steps.
1. Carry the box to where you will unpack it.
2
2. Remove the bands.
3. Open the box and take out the following components.
x3
3
Printer main body
Accessory box
No.
1
2
1
Name
Printer main body
Accessory box(Large)
Accessory box(Small)
Installation Manual (this manual)
3
Q'ty
1 set
2
1
1
2
No.Name
1
Leg part (Right)
2
Leg part (Left)
3
Connector bar
4
Base parts
5
Waste fluid tank holder
6
Hexagon socket head cap screws
7
Waste fluid tank holder fixing screws
8
Butterfly screws
9
Hexagonal wrench
2.4 Contents of Media-feed table
(optional) box
㧔half side㧕
1
2.2‫ޓ‬Items in the accessory box
3
1
2
Q'ty
1
1
1
2
1
8
4
8
1
3
2
3
4
6
5
4
4
5
6
5
9
7
8
6
5
10
7
6
11
10
9
8
10
8
12
9
x3
7
11
13
12
11
No.
1
2
3
4
5
6 ‫ޓ‬
7
8‫ޓ‬
1.2
Name
Top cover
Top board
Outer board
Center board
Side board A
Side board B
No.
Name
10
Installation Manual
(this manual)
Cushion (Left)
Cushion (Right)
11
Printer main body
9‫ ޓ‬Container box for
accessories (Large) 2pcs
Container box for
accessories (Small) 1pcs
Unpacking Stand, Media-feed
table
No.
1
2
3
4
‫ޓ‬5
6
‫ޓ‬7
8
9
10
11
12
13 Name
Clean stick
Gloves
Flushing box sponge
Spirit level
Paper towel
Waste fluid tank
Cleaning fluid (250 ml)
Dropper
Plastic cup
Tray
Operation Manual CD
Using a Manual CD-ROM
Notes for using the dedicated ink
Follow the procedure below to unpack the Stand,
Media-feed table F, and Media-feed table R.
*Media-feed tables F and R are optional.
1. Carry the box to where you will unpack it.
2. Open the box and take out the components.
VJ1626UHE-I-00
2
Q'ty
10
10
10
1
5
1
1
2
1
1
1
1
1
13
No.Name
1
Frames
2
Leg (left)
3
Leg (right)
4
Reinforcement
5
Rails (fixed)
6
Stopper
7
Installation plate (Left)
8
Installation plate (Right)
9
Hexagon socket head cap screw
10
Screw
11
Lug screw
12
Hexagonal spanner
13
Hexagonal wrench
Q'ty
1
1
1
1
1
1
2
2
8
8
1
2
1
VJ-1626UH INSTALLATION MANUAL
3 Assembling
4. Fasten the connector bar to the left stand in the
same way as in Step 3.
This section explains how to assemble the printer.
1
CAUTION
Assemble this printer with 4 persons
or more.
2
Front
3
3.1
3. Remove the two transfer stays and fasten the
printer to the stand using eight butterfly screws.
1
2
Assembling the stand
1
1. Follow the procedure below to assemble the right
stand.
a. Attach the right leg part to the right base part so
that four screw holes in the base part are at the front.
b.Tighten two hexagon socket head cap screws using a
hexagonal wrench.
3
3
Follow the procedure below to assemble the stand.
2
2
3
3
No.
Name ‫ޓޓޓ‬No.
‫ޓ‬Name
3‫ޓ‬Hexagon socket head cap screws
1‫ޓޓޓ‬Stand (Left)
2‫ޓޓޓ‬Connector bar
5. Attach the waste fluid tank holder to the right
stand using four waste fluid tank holder fixing
screws.
3
3
No.
‫ޓޓ‬Name
‫ޓ‬No.Name
Transfer stays‫ޓޓޓޓޓޓ‬Butterfly screws
2‫ޓޓ‬Stand
4. Follow the procedure below to attach the waste fluid tank.
a. Place the waste fluid tank in the waste fluid tank
holder.
b. Attach the waste fluid tube to the tank.
c. Insert the waste fluid sensor cable into the
connector on the bottom of the printer.
1
3
1
3
2
Front
2
4
3
No.
Name ‫ޓޓޓ‬No.
‫ޓ‬Name
3‫ޓ‬Hexagon socket head cap screws
1‫ޓޓޓޓ‬Leg part (Right)
2‫ޓޓޓޓޓ‬Base part
4‫ޓ‬Screw holes in base part
2. Assemble the left stand in the same way as in Step 1.
6. Shake the stand to make sure that each part is
firmly attached.
‫ޓ‬When the printer is wobbly, loosen the hexagon
socket head cap screws once and then tighten
them again.
3.2
Attaching the stand
Follow the procedure below to attach the stand to the
printer.
1. Turn the four adjusters as shown below to prevent
the stand from moving.
1
2
1
4
2
1
No. ‫ޓ‬Name
‫ޓ‬No.
Name
1‫ޓޓ‬Waste fluid tank holder 4‫ޓ‬Waste fluid sensor cable
2‫ޓޓޓ‬Waste fluid tank
5‫ޓ‬Waste fluid sensor connector
3‫ޓޓ‬Waste fluid tube
3.3
1. Remove all tapes from each cover.
3.Open the right Maintenance cover, and remove all
the packing materials that are fixed with tape.
2
4. Remove a screw from the head unit fastening
material (metal plate) and remove the material.
1
1
No.
Name
1‫ޓޓޓޓ‬Adjusters
3
No.
Name ‫ޓޓޓ‬No.
‫ޓ‬Name
3‫ޓ‬Hexagon socket head cap screws
1‫ޓޓޓޓ‬Leg part (Left)
2‫ޓޓޓޓ‬Base part
4‫ޓ‬Screw holes in base part
3. Fasten the connector bar to the right stand using
two hexagon socket head cap screws.
2. Insert the two transfer stays into the right and left
transfer brackets, lift the printer with four or more
people and place it on the stand.
2
No.
Name‫ޓ‬
1
Head unit
‫ޓޓޓޓޓޓޓޓޓޓ‬
2
Screw
1
2
3
1
2
‫ޓ‬No. ‫ޓޓޓޓ‬Name
Head unit fastening
3
material (metal plate)
5. Open the left maintenance cover, then place the tray.
1
2
4
1
3
No.
Name ‫ޓޓޓ‬No.
‫ޓ‬Name
3‫ޓ‬Hexagon socket head cap screws
1‫ޓޓޓޓ‬Stand (Right)
2‫ޓޓޓޓ‬Connector bar
4‫ޓ‬Groove in connector bar
1
3
‫ޓޓޓ‬No.
‫ޓ‬Name
2‫ޓޓ‬Stand
‫࡮ޓ‬Attach the connector bar with the groove facing
the rear as shown below.
Front
Detaching fastening materials
This printer has fastening materials in the place shown
below.
2. Open the front cover and remove all protection
materials fixed with tape.
Front
4
5
No.
Name ‫ޓޓޓ‬No.
‫ޓ‬Name
1‫ޓޓޓ‬Leg part (Right)
3‫ޓޓ‬Waste fluid tank holder
fixing screws
2‫ޓޓ‬Waste fluid tank holde
2
1
No.
Name ‫ޓޓޓ‬No.
‫ޓ‬Name
3‫ޓޓ‬Stand
1‫ޓޓޓޓ‬Transfer stays
2‫ޓޓޓ‬Transfer brackets
3
No. ‫ޓޓ‬Name‫ޓޓޓޓޓ‬No. ‫ޓޓ‬Name
1‫ޓ‬Maintenance cover‫ޓ‬2‫ޓޓޓޓ‬Tray
VJ1626UHE-I-00
VJ-1626UH INSTALLATION MANUAL
3.4 Assembling the Media-feed
table (optional)
5.Use the lug screw to fix Stopper on Frame
Follow the procedure below to assemble the
Media-feed table.
࡮Install Stopper so that the curved part matches
Frame.
࡮Install Stopper on the side of rail retaining screw.
2
3.4.1‫ޓ‬Assembling the Media-feed table
1. Use hexagon socket head cap screws (4 pieces) to
fix the reinforcement between the legs (right and
left).
1
Install this product to the appropriate place with
reference to the following.
4
WARNING
3
2
3
3
4
1
Front
No. ‫ޓޓ‬Name
‫ޓޓޓ‬No.
‫ޓ‬Name
1‫ޓޓޓޓޓ‬Leg (left)
3‫ޓޓޓ‬Reinforcement
4‫ޓ‬Hexagon socket head cap screws
2‫ޓޓޓޓ‬Leg (right)
Place the convex sections of the legs (right and left)
along the notch of the reinforcement to assemble.
1
No. ‫ ޓޓ‬Name
1‫ޓޓޓޓޓ‬Frame
2‫ޓޓޓ ޓ‬Stopper
‫ ޓޓޓ‬No.
‫ ޓ‬Name
3‫ ޓޓ ޓ‬Lug screw
4‫ޓ‬
Rail retaining screw
6. Use the screws (2 pieces each) and fix Installation
plates (R and L) on Frame.
࡮Install Installation plates on the opposite side of rail
fixing screw.
2
1
3
1
3
2
Front
No. ‫ޓޓ‬Name
‫ޓޓޓ‬No.
‫ޓ‬Name
1‫ޓ‬Leg (left), leg (right)‫ޓ‬2‫ޓޓޓ‬Reinforcement
2. Place the Frame on the legs and fix it with four
hexagon socket head cap screws.
Procedures and environment for installing this product
are explained.
4.1 Installation environment
2
4
4 Installation
Do not install the printer in the
following places where there is a
possibility that the printer may be
damaged or might fall or be fallen by
chance.
On a shaky stand
Slanting location
Places where vibration of other machines
etc. is transmitted.
Do not step on the printer or place
heavy things on top of it.
It may cause an injury if the printer
falls down.
Do not block the vent by covering the
printer with cloths, such as a blanket or
tablecloth. If the vent is blocked, heat
may accumulate inside the printer and
it may cause fire.
Do not install the printer in a location
that has high humidity or is dusty.
It could lead to electric shock and fire.
4.1.1 Installation environmental condition
Select an installation location in accordance with the
table below.
3
Floor strength of
installation place
1
2
Front
No.
1
7. Assemble the other side of Media-feed table in the
same way
2
Name
Frame
No.
2
No.‫ޓޓ‬Name
‫ ޓޓޓ‬No.
‫ ޓ‬Name
1‫ ޓ‬Installation plates (R)
3‫ޓޓ ޓ‬Frame
4‫ޓޓ ޓ‬Screw
2‫ ޓ ޓ‬Installation plates (L)
Power
Rated
Specifica- voltage
tion
Frequency
Range
Power
capacity
AC100-240V
50/60Hz ± 1Hz
100V-120V: Total of 4.0A
200V-240V: Total of 2.0A
Environm- Operative
condition
ental
conditions Printing
accuracy
coverage
Name
Hexagon socket head
cap screws
More than 2940 Pa (300 kg/m2)
Temperature: 20 °C to 32 °C
Humidity: 40 % to 60 %, No Condensation
Temperature: 22 °C to 30 °C
Humidity: 40 % to 60 %
Without condensation
Change
rate within Temperature: within 2 °C per hour
warranty Humidity: within 5 % per hour
Firmly insert the protruding portions of the legs
to the holes of the Frame to fix it.
NOTE
For temperature and humidity, avoid locations
such as the following. There is a possibility that
the print quality will be affected.
Places where temperature or humidity may
rapidly change, even though within the required
conditions.
Places that receive direct sunlight, increased illumination or direct air, for example from an air
conditioner.
To keep the temperature and humidity constant,
install this product in a location where the air
condition is adjustable.
4. Use the screws (4 pieces) to fix Rails (fixed) on
the center of Frame.
‫ޓ‬When installing Rails (fixed), make sure that
the left and right rails are facing the same way.
3
2
1
4.1.2 Installation space
No.
1
2
Name
Rails(fixed)
Frame
No.
Name
3
Screw
Install on a level floor which meets the following condition.
It has enough strength to support the weight of the
printer and the stand.
NOTE
For the weight of the printer and the stand, refer to
the Operation Manual.
(Continue to next)
VJ1626UHE-I-00
4
‫ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ‬
(1) When using the Media-feed table
1,000mm
NOTE
2,7mm
1,000mm
4,730mm
1,000mm
࡮ If the height of the positioning guide does not
match the square hole, turn the screw of
Mediafeed table's caster, and adjust the height.
(See step 5.)
2
1
When using rigid media on this printer, use
Media-feed table (optional).
2
The following items are required for installing
Media-feed table:
4,698mm
(2) When not using the Media-feed table
1
• Spanner: Accessories for Media-feed table
• Level: provided with the printer
㧔㧝㧕Rear side
1,000mm
818mm
1,000mm
2,818mm
1,000mm
When Using the roll media for “10 Checking the
printing condition”, you do not need to install
Media-feed table.
4. Insert the positioning guide of Media-feed table
into the square hole of Paper guide R.
Follow the procedure below to install Media-feed
table.
1,000mm
2,698mm
4.2.2‫ޓ‬Installing the Media-feed tables
(optional)
VJ-1626UH INSTALLATION MANUAL
1. Loosen the fixing levers on the right and left side
of the rear. Set the distance between the roll media
holders wider than the roll media width.
2,698mm
1
4,698mm
4.2 Installation procedure
3
5.‫ޓ‬Turn the screws on the caster of Media-feed table
(2 places, ones closer to the printer) with a spanner.
Adjust so that there is a 6 mm gap between the top
side of the square hole of Paper guide R and the
top side of the positioning guide.
2
1,000mm
‫ޓޓ‬No.
Name ‫ ޓޓޓ‬No.
‫ޓޓ‬Name‫ޓ‬
1‫ ޓޓ‬Positioning guide‫ޓ‬
2‫ޓޓ ޓ‬Square hole
3
WARNING
1
Caster of Media-feed table has 2 types
of screws.Turn the bottom screw.
Turn the screw clockwise to raise Media
-feed table.
2
Install this product to the installation place in
accordance with the list shown below.
4.2.1 Installing the printer main unit
1. Carry the printer to the installation place.
2. Turn the following adjusters in the direction as
shown below to prevent the printer from moving.
Stands: adjusters (4)
No. ‫ ޓޓޓޓ‬Name‫ ޓޓޓޓޓ‬No.‫ ޓޓޓ‬Name
1‫ޓ‬Roll media holder㧔L㧕
3‫ޓ ޓ‬Fixing Lever
2‫ޓ‬Roll media holder㧔R㧕
2
2. Loosen retaining screws of Media-feed table, and
slowly level the table.
6mm
1
2
1
1
2
‫ޓޓ‬No.
Name ‫ ޓޓޓ‬No.
‫ޓޓ‬Name‫ޓ‬
1‫ޓޓ‬Screw on the casters
2‫ ޓ‬Positioning guide‫ޓ‬
2
1
6. Place the level at the edge of printer's platen, and
check the position of the air bubble.
1
No. ‫ ޓޓ‬Name
‫ ޓ‬No.
‫ޓޓ‬Name
1‫ ޓ ޓޓ‬Adjuster‫ ޓޓޓޓ‬2‫ ޓޓޓ‬Stand
3. Set the level on the right and left platens and
adjust so that the printer stays flat.
1
1
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
1‫ޓޓ‬Media-feed table‫ޓ‬
2
‫ޓ‬
‫ޓޓ‬Name‫ޓ‬
Leveling screw‫ޓ‬
2
1
3. Tighten the leveling screws of Media-feed table (2
places, both sides), and fix the table.
WARNING
When fixing the leveling screws, hold
the frame while pressuring the rubber
foot, and then turn the
screw until it doesn't turn any further.
1
1
2
No.
1‫ޓޓޓ‬
2
‫ޓޓ‬No.
Name
‫ ޓޓޓ‬No .
‫ޓޓ‬Name‫ޓ‬
1‫ޓޓޓޓ‬Level‫ ޓޓޓ ޓ‬2‫ޓޓ ޓ‬
Platen
7 . Place the level on the frame of Media-feed table.
Place the level on the same side as when you ‫ޓ‬
‫ޓ‬placed it on the printer.
Name No.
‫ޓޓ‬Name
Level‫ ޓޓޓ ޓ‬2‫ޓ ޓޓ‬Adjuster
2
1
1
4. Confirm that the waste fluid valve is closed.
2
3
1
‫ޓޓ‬No.
Name
‫ޓ‬No.
‫ޓޓ‬Name‫ޓ‬
1‫ޓޓޓޓ‬Level‫ޓޓ ޓ‬2‫ޓ ޓ‬Frame of Media-feed table
No. ‫ ޓޓޓ‬Name
1‫ ޓޓޓ‬Waste fluid valve
‫ ޓ‬No.
Name
No. ‫ ޓޓޓ‬Name
1‫ޓޓޓ‬Media-feed table
2‫ޓޓ ޓ‬Leveling screw
‫ ޓ‬No.
Name
3‫ ޓ ޓ‬Frame
5
VJ1626UHE-I-00
VJ-1626UH INSTALLATION MANUAL
5 Power cable connection
4.‫ޓ‬Turn the screws of Media-feed table's caster (2
places, closer to the printer) with a spanner so that
the top side of Media-feed table's positioning
guide slightly touches the top side of Paper guide
F's square hole.
8. Turn the screw of Media-feed table's caster (the
one further from the printer) with a spanner, and
adjust the slant.
Make sure that the position of the level's air
bubble is at the same position as when you place it
on the printer.
This section explains power cable connection.
CAUTION
2
Caster of Media-feed table has 2 types of
screws. Turn the bottom screw.
Turn the screw clockwise to raise Mediafeed table.
2
6mm
1
1
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
1‫ޓޓ‬Scrwews on Casters
2‫ޓ‬
2
Name‫ޓ‬
Level‫ޓ‬
9.‫ޓ‬Adjust the slant on the other side in the same way.
CAUTION
If Media-feed table's slanted, media may
touch Print head, and Print head may break.
CAUTION
Pay attention to the following points when
handling power cable.
• Do not tamper with the power cable.
• Do not put heavy objects on the power
cable.
• Do not bend, twist or pull the power
cable by force.
• Do not route the power cable near heating
appliances.
1
1
‫ޓޓ‬No.
Name
‫ ޓޓޓ‬No.
1‫ޓޓ‬Screws on Caster
2‫ޓ‬
‫ޓޓ‬Name‫ޓ‬
Positioning guide‫ޓ‬
5. Place the level at the edge of printer's platen, and
check the position of the air bubble.
㧔㧞㧕Front side
1. Loosen retaining screws of Media-feed table, and
slowly level the table.
1
WARNING
Be sure to use the power cable supplied
with the printer.Using other power cables
can cause an electric shock or fire.
Use the power cord set compliant with the
safety standards, power-supply voltage,
and plug shape of the country where the
printer is used.
Use a power cord set which is equipped
with a protective earth, and securely
connect it to the outlet.
Do not use a damaged power cable.
It could lead to an electric shock and fire.
2
1
NOTE
Contact your local MUTOH dealer in case of
power cable damage.
‫ޓޓ‬No.
Name
‫ ޓޓޓ‬No.
‫ޓޓ‬Name‫ޓ‬
1‫ޓޓޓޓ‬Level ‫ ޓޓޓ ޓ‬2‫ ޓޓ ޓ‬Platen
2
‫ޓޓ‬No.
Name ‫ ޓޓޓ‬No.
1‫ޓޓ‬Media-feed table
2‫ޓ‬
This product is also designed for IT power
distribution system with phase-to-phase
voltage 230V.
‫ޓޓ‬Name‫ޓ‬
Leveling screw‫ޓ‬
6 . Place the level on the frame of Media-feed table.
Place the level on the same side as when you
placed it on the printer.
2 . Tighten the leveling screws of Media-feed table (2
places, both sides), and fix the table.
1
Follow the procedure below to install the power cable.
1. Make sure that the printer is turned OFF.
2
1
NOTE
When fixing the leveling screws, hold the frame
while pressuring the rubber foot, and then turn the
Media Type
screw until it doesn't turn any further.
‫ޓޓ‬No.
Name ‫ޓޓޓ‬
1‫ޓ‬Frame of Media-feed table
1
Heater Link
Roll
Origin
Rigid
No. ‫ޓޓ‬Name‫ޓ‬
2‫ޓ‬
Level
Long Feed
7. Turn the screw of Media-feed table's caster (the
one further from the printer) with a spanner, and
adjust the slant.
Make sure that the position of the level's air
bubble is at the same position as when you place it
on the printer.
2
‫ޓޓ‬No.
Name
‫ ޓޓޓ‬No.
1‫ޓ‬Media-feed table
2‫ޓ‬
‫ޓޓ‬Name‫ޓ‬
Leveling screw
The power is ON when the [Power] key of
the operation panel is pressed in.
Press the key once again to turn OFF the
power.
2
2. Connect the power cable to the AC inlet on the
rear side of the product.
3.‫ޓ‬Insert the positioning guide of Media-feed table
into the square hole of Paper guide F.
࡮If the height of the positioning guide does not
match the square hole, turn the screw of Mediafeed
table's caster, and adjust the height. (See step 4.)
1
NOTE
1
2
1
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
‫ޓޓ‬0COG‫ޓ‬
1‫ޓޓ‬Screws on Caster
2‫ ޓ‬Level
2
1
‫ޓ‬Adjust the slant on the other side in the same way.
‫ޓޓ‬No.
Name
1‫ޓޓޓ‬AC inlet
2
1
‫ޓޓ‬No.
Name ‫ ޓޓޓ‬No.
‫ޓޓ‬Name‫ޓ‬
1‫ ޓ‬Positioning guide ‫ ޓ‬2‫ ޓ‬Square hole
VJ1626UHE-I-00
6
‫ ޓޓޓ‬No.
2‫ޓ‬
‫ޓޓ‬Name‫ޓ‬
Power Cable
‫ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ‬VJ-1626UH INSTALLATION MANUAL
3. Insert the power cable plug firmly in the socket.
WARNING
6 Turning the power ON/OFF
6.2
Set sleep mode on the printer
1. Make sure that the printer's operating condition is
as follows:
This section explains how to turn the printer
•
Printing or other operation is not in progress.
ON/OFF, and how to start the sleep mode.
• Operation panel display is in the Normal condition.
CAUTION
• There is ample amount of ink in the ink packs.
Operation Manual 5.3.15 Ink Status menu
࡮You need to let the ink flow inside the printer
Operation Manual 6.4.1 Replacing ink bags
regularly, therefore, do not turn OFF the
Do not pull out or insert the power plug with
a wet hand.
This could lead to an electric shock.
Make sure to use only the specified power
supply (AC 100 V to 120 V or AC 220 V to
240 V).If a power supply other than the
printer after regular operation; make sure
specified voltage is used, it could cause an
you use the sleep mode.
electric shock and fire.
࡮If you have to turn OFF the printer, read
Take power for the printer directly from
“3.2.2 Turning the power OFF” in the
the power socket (AC 100 V - 120 V or AC
Operation Manual.
220 V - 240 V).Do not use multiple plugs
࡮The procedures to turn OFF the printer
on the same socket.This could generate
are different for 4-color set usage and
heat and might cause fire.
5-color set usage.
Be sure to use a dedicated power socket
with earth wire for the power supply, and
connect it to the earth wire.
If the earth wire is not connected, an
6.1 Turning the power ON
electric shock or fire may occur.
Do not connect an earth wire to the following Follow the procedure below to turn the power ON.
places.
1. Press the [Power] key on the operation panel to
• Gas pipe
turn ON the printer.
There is a possibility of ignition and explosion.
‫࡮ޓ‬The
Power lamp on the operation panel lights up
• Earth wire of telephone cables and
in blue.
lightning rods
Heavy current might flow whenever lightning ‫࡮ޓ‬The printer starts initial operation.
strikes.
‫࡮ޓ‬When the initial operation is complete, the
Water pipe and faucet
printer enters Normal.
The earth might not work if a plastic pipe
is connected in the middle of the metal pipe.
• There is enough free space in the waste fluid bottle.
Operation Manual 6.6 Disposal the waste fluids
• Front cover is closed.
• Media loading lever is lowered
(Media loading lever on the rear side is raised).
2. Press the [Menu] key on Operation panel.
Media Type
Heater Link
Roll
Origin
Rigid
Long Feed
‫"࡮ޓ‬Menu1: Sleep Mode" is displayed on Operation
panel.
3. Press the [>] key on Operation panel.
CAUTION
• Pay attention to the following points
when handling the power supply plug.
Any mishandling of the power cable could
cause a fire.
• Make sure that no foreign substances such
as dust etc. are stuck to the power plug.
• Make sure that the power plug is firmly
inserted to the edge of the power socket.
• When you do not use the printer for a
long period, make sure to pull out the
power plug from the power socket for safety.
• If you are leaving the printer unplugged
for a long time, follow the procedure in
"6.3.1 Operation procedure for long storage"
to turn the power OFF, and then unplug the
power plug.
• Make sure to connect an earth wire to the
earth connection that meets the following
standards.
• Earth terminal of power socket
• Earth wire with copper plate which is
buried at 650 mm or more, deep in the
ground.
• Earth wire with copper plate which is
buried at 650 mm or more, deep
Media Type
Heater Link
Roll
Origin
Rigid
Media Type
Long Feed
Heater Link
Roll
Origin
Rigid
NOTE
• If there is a problem during the initial
operation, a message is displayed on the
operation panel and the printer may stop
‫"࡮ޓ‬Sleep Mode1: Timer Set" is displayed on
operating.If operation stops, refer to
"7 Troubleshooting"and deal with the problem. Operation panel.
‫ޓ‬
Long Feed
4. Press the [Enter] key on Operation panel.
Media Type
Heater Link
Roll
Origin
Rigid
NOTE
࡮Contact the retail outlet of purchase if the
‫ޓ‬earth connection cannot be established,
or if the earth connection is not given.
࡮When the power supply of the printer is
ON, do not pull out the power cable from
the power socket.Whenever the plug is
pulled out from the power socket, allow
one minute or more before inserting the
plug in the power socket again.
Long Feed
‫"࡮ޓ‬Timer: Off" is displayed on Operation panel.
7
VJ1626UH-I-00
VJ-1626UH INSTALLATION MANUAL
5. Use the [+] or [-] key on Operation panel to select the head
cleaning interval.
10.Use the [+] or [-] key on Operation panel to select
"Sleep Mode3: Start".
8
Initial ink filling
Follow the procedure below to perform initial ink
filling.
‫"࡮ޓ‬Start Sleep Mode?" is displayed on
Operation panel.
1. Turn the printer ON.
‫࡮ޓ‬The printer starts the initializing operation.
Media Type
Heater Link
Roll
Origin
Rigid
11.Press the [Enter] key on Operation panel.
‫࡮ޓ‬After the initial operation is complete, "Start
Ink Charge -> E" is displayed on Operation panel.
2.‫ޓ‬Press the [Enter] key on Operation panel.
Long Feed
‫࡮ޓ‬For the head cleaning intervals, select from the
following. When more than the set time has passed,
Print head is cleaned automatically.
Media Type
Heater Link
Roll
Origin
Rigid
Media Type
‫࡮ޓޓ‬Off㧦Head cleaning is not performed.
6. Press the [Enter] key on Operation panel.
Media Type
Heater Link
Roll
Origin
Rigid
Long Feed
‫࡮ޓ‬The timer has been set.
Rigid
Long Feed
‫ޓ‬
‫"࡮ޓ‬Restart -> ENTER" is displayed on Operation
panel.
Even when the timer is set to Off, a small
amount of ink is automatically charged once
every week.Also, when using the 6-color
set, cleaning and flushing are automatically
performed when the sleep mode is
cancelled.This is for maintaining the print
head and ink.
Roll
Origin
Long Feed
‫࡮ޓޓ‬1 to 6/9/12/18/24H: Head cleaning is
‫ޓޓޓ‬performed at a set interval of time.
NOTE
Heater Link
‫"࡮ޓ‬Ink Comb.: 4Color" is displayed on Operation
panel.
‫࡮ޓ‬The printer goes into sleep mode.
NOTE
If you press the [Enter] key during sleep mode,
the printer returns to the Normal condition.
If the printer is under one of the following
conditions while shifting to sleep mode,
"Don'tStartSleepMode" is displayed, and sleep
mode does not start.
࡮‫ޓ‬Front cover or Maintenance cover is open.
࡮‫ޓ‬Front media loading lever is raised
(Rear media loading lever is lowered).
࡮‫ޓ‬Waste fluid tank is full.
࡮‫ޓ‬There is little remaining ink in the ink pack
(or no ink)
࡮‫ޓ‬Ink pack has been removed.
࡮‫ޓ‬An ink pack other than genuine ink pack is
inserted into Cartridge slot, etc.
Activate Sleep Mode again after returning
the printer to a normal state.
‫ޓޓޓޓ‬Operation Manual “7.2 Error messages”
3.Use the [+] or [-] key on Operation panel to select
the number of ink colors you want to use.
Media Type
Heater Link
Roll
Origin
Rigid
Long Feed
‫"࡮ޓ‬Ink Comb.: 4Color": Cyan (C), Magenta (M),
Yellow (Y), and Black (K)
‫"࡮ޓ‬Ink Comb.: 5Color": Cyan (C), Magenta (M),
Yellow (Y), Black (K), and White (WH)
4.Press the [Enter] key on Operation panel.
‫"࡮ޓ‬Sleep Mode1: Timer Set" is displayed on Operation
panel.
Use the [+] or [-] key on Operation panel to select "Sleep
Mode2: Start".
Media Type
7. Product activation
‫"࡮ޓ‬Time: Short" is displayed on Operation panel.
This printer requires activation when the power is
turned ON for the first time.
8. Use the [+] or [-] key on Operation panel to select the
cleaning mode while in sleep mode.
࡮Short: Discharges smaller amount of ink compared to
Normal.
࡮Normal: Select this mode normally.
࡮Long: Discharges a larger amount of ink compare to
Normal.Use this when "Normal" Head cleaning cannot
improve the problem of the Print head.
When "Activation required" is displayed on the
Operation panel, refer to "Product activation guide"*
to perform activation.
*Please download the "Product Activation Guide"
from the ValueJet Club below.
https://valuejetclub.mutoh.co.jp/mutoh/guser/
9. Press the [Enter] key on Operation panel.
Media Type
Heater Link
Roll
Origin
Rigid
Long Feed
VJ1626UHE-I-00
8
Heater Link
Roll
Origin
Rigid
Long Feed
‫"࡮ޓ‬Empty WasteInk ->" is displayed on Operation
panel.
NOTE
If this message is displayed during operation,
check Waste fluid tank and remove any waste
fluid. If there is waste fluid inside the tank, the
cleaning liquid is wasted.
‫ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ‬VJ-1626UH INSTALLATION MANUAL
࡮‫ޓ‬You can check the ink color labels for ink colors
and its cartridge slots.
10. Prepare ink cartridges.
5. Press the [Enter] key on Operation panel.
The number of ink cartridges or Cleaning cartridges
to be used differs depending on the number of
colors selected in step 3.
࡮‫ޓ‬Keep the arrow of ink cartridge facing up and
insert it into the printer.
㧔1㧕When using 4-color set
Media Type
Heater Link
Roll
Origin
Rigid
࡮‫ޓ‬Insert ink cartridges all the way in Ink cartridge
slot.
Cyan (C): 2
Magenta (M): 2
࡮‫ޓ‬When a ink cartridges are installed, "Ink Refill
**%" is displayed on Operation panel and ink
replenishment starts.
Yellow (Y): 1
Black (K): 1
࡮‫ޓ‬Initial replenishment takes about 9 minutes.
Long Feed
㧔2㧕When using 6-color set
࡮‫"ޓ‬Insert CleaningCart." is displayed on Operation
panel.
Cyan (C): 1
6.Prepare the cleaning cartridges.
Yellow (Y): 1
࡮‫ޓ‬Number of the cleaning cartridges required: 6
Black (K): 1
7.Insert cleaning cartridges into all Ink cartridge slots.
Varnish (VA): 1
࡮‫ޓ‬Ink filling operation and pause operation are
repeated during the initial ink replenishment.
Magenta (M): 1
࡮‫ޓ‬When 100% is displayed, the initial ink
replenishment is complete.
࡮‫ޓ‬After the initial ink replenishment is complete,
"Media End" is displayed on Operation panel.
White (WH): 1
2
1
CAUTION
11. Shake ink cartridge horizontally 10 times.
Comply strictly with the following during
ink filling.If filling is interrupted, ink will be
lost when filling is resumed.
• Do not turn OFF the printer.
2
‫ޓޓ‬No.
Name
1‫ޓ‬Cleaning cartridge
‫ޓޓޓ‬No.
Name‫ޓ‬
‫ ޓ‬2‫ޓޓ‬Ink cartridge slots
‫ޓޓ‬No.
Name
1‫ޓ‬Ink cartridge
࡮‫ޓ‬Keep the arrow of Cleaning cartridge facing up
and insert it into the printer.
࡮‫ޓ‬Insert Cleaning cartridges all the way in Ink
cartridge slot.
࡮‫ޓ‬When all Cleaning cartridges are installed,
"Busy-Washing" is displayed on Operation panel,
and the printer starts charging the cleaning fluid.
• Do not unplug the power cord set of the
printer.
1
‫ޓޓޓ‬No.
• Do not open Front cover.
Name‫ޓ‬
• Do not open Maintenance cover.
• Do not raise Media loading lever.
CAUTION
Shake the ink cartridge before use.
Shake the ink cartridges periodically.
Otherwise, the ink inside the cartridges
settles or coagulates and may cause
poor print quality or a malfunction.
• Do not use ink packs that have little ink
remaining.
NOTE
If the printer perform the nozzle check printing
immediately after initial charging is complete, the
following results may occur.
࡮‫ޓ‬When Cleaning fluid has been charged, "Remove
Cartridges" is displayed on 1RGTCVKQPRCPGN
8. Remove all Cleaning cartridges.
• Printed lines become blurred.
12.Install ink cartridges into Ink cartridge slots.
࡮ "Busy-Washing" is displayed on Operation panel
and the printer starts Head cleaning.
࡮ After Head cleaning is complete, "Check waste
fluid" is displayed on Operation panel.
• The data is partially not printed.
NOTE
Note that the ink colors and corresponding ink
cartridge slots differ depending on the number of
ink colors selected in step 3.
In such cases, follow Operation manual "5.5
Cleaning menu" and refill a small amount of ink.
Then, check the printing result.
If there is no improvement in the print result even
after refill a small amount of ink, leave the printer
unused for an hour or more. Then, refill a small
amount of ink again and check the print result.
࡮ Check Waste fluid tank.‫ޓ‬
(1)When using 4-color set
If there is still no improvement, contact your local
MUTOH dealer.
1
M
4 colors
M
C
C
4 colors
K
Y
1
2
‫ޓޓ‬No.
Name
1‫ޓ‬Cleaning cartridge
‫ޓޓޓ‬No.
Name‫ޓ‬
‫ޓޓ‬
9. Press the [Enter] key on Operation panel.
2
‫ޓޓ‬No.
Name
1‫ޓ‬Ink cartridge
‫ޓޓޓ‬No.
Name‫ޓ‬
2‫ޓޓ‬Ink cartridge slots
(2)When using 6-color set‫ޓ‬
K
Roll
Origin
Rigid
6 colors
VA WH
Y
1
Media Type
Heater Link
6 colors
M C
2
2
Long Feed
‫ޓ‬
‫ޓޓ‬No.
Name
1‫ޓ‬Ink cartridge
‫ޓޓޓ‬No.
Name‫ޓ‬
2‫ޓޓ‬Ink cartridge slots
‫ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ‬9‫ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ‬VJ1626UHE-I-00
VJ-1626UH INSTALLATION MANUAL
Loosen the rail retaining screw on Media-feed
table (rear side), and widen the rails to the sides so
that you can place the rigid media. Make sure that
the rigid media is set on the center of the printer.
9 Setting media
This section explains how to set media.
Put the media in the center.
NOTE
For the roll media that can be attached to the
scroller supplied with this unit, refer to "4.2.1
Loadable media" in the Operation Manual.
If the right edge of the roll media goes further
right from the loading mark when seen from the
front, adjust the position of Media-feed table's
rails.
TIP
Loading mark is not used for deciding where the
right edge of the media should be placed.
2
There should be no problem if the media is placed
away from the line, as long as it does not go
beyond the line.
1
9.1 Loading rigid media
‫ ޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓ‬
1‫ޓ‬Rail‫ޓޓޓޓޓ‬2‫ޓޓ‬Rail retaining screws
6. Place the rigid media on the rails and tighten the
rail retaining screw at where there is a 5 mm gap
between the stoppers on both sides and the media.
You can load the following rigid media on this
printer:
࡮Maximum width: 1,625 mm
࡮Minimum width: 182 mm
࡮Maximum depth: 1,200 mm
࡮Minimum depth: 200 mm
࡮Thickness: 15 mm or less (including media
warpage and unevenness)
࡮Weight: 15 kg or less
࡮Media warpage: Less than 1 mm. (when the
media thickness is uneven, make sure that the
total‫ޓ‬of the warpage and unevenness is less
than 1 mm. Also, do not print with the warpage
facing up.)
1
1
NOTE
1
2
‫࡮ޓ‬Make sure that the rigid media is placed parallel
to the media feeding direction.
‫࡮ޓ‬Make sure that the rigid media is placed on the
ball part on the rails.
‫࡮ޓ‬Adjust and fix the rails so that they are parallel to
the rigid media.
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓ‬
1‫ޓ‬Rigid media‫ޓޓޓ‬
2 ‫ޓ‬Media loading mark
If the both edges of the media do not cover more
than half of Pressurizing rollers, adjust the
position of Media-feed table's rails.
When loading the rigid media so that it does not
cover more than half of Pressuring rollers, make
5mm
1
2
3
3
sure that the both edges of the media does not
cover Pressurizing rollers.
OK
‫ ޓ‬See the following for loading the rigid media (only
when adjusting Media-feed table).
1
‫࡮ޓ‬Spanner: provided with Media-feed table
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓޓ‬
1‫ޓ‬Rigid media‫ޓޓ ޓ‬
2‫ ޓ‬StoppeT
3‫ޓ‬Rail retaining screw
‫ޓ‬Follow the procedure below to load the rigid media.
1. Turn the printer ON.
2. In Panel setup menu, check if the "media type" for
the User type you're going to use is appropriately
set.
Bad
OK
2
2
2
1
1
1
Place the rigid media on Media-feed table (front
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓ‬
side) in the same way, and fix the rails at where
1‫ޓ‬Rigid media‫ޓޓޓ‬
2 ‫ޓ‬Pressurizing roller
there is a 5 mm gap between the stoppers on both
sides and the media.
‫ޓޓޓޓ‬Operation Manuaľ4.3.2 Menu setup
procedure̍
5mm
‫ޓޓޓޓ‬Operation Manuaľ5.2.2.10 MediaType
men”
1
2
3
3
NOTE
If the type of the media you have loaded differs
from that of the user type you have set, the media
may not be detected properly.
11. Lower Front media loading lever. (Raise Rear
media loading lever)
Media-feed table is excluded from the illustration
for simplicity.
1
2
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓޓ‬
1‫ޓ‬Rigid media‫ޓޓ ޓ‬
2‫ ޓ‬StoppeT
3‫ޓ‬Rail retaining screw
3. Raise Front media loading lever (lower Rear media
loading lever).
8. From the rear side of the printer, insert the rigid
media into Media feed slot.
2
1
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓ‬
1‫ޓ‬Front media loading ‫ ޓ‬2‫ ޓ‬Rear media loading lever
‫ ޓ‬lever
3
1
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓ‬
1‫ޓ‬Front media loading
2‫ ޓ‬Rear media loading lever
‫ ޓ‬lever
NOTE
Push Front media loading lever down and lower
it firmly. For Rear media loading lever, push it
up firmly. If the lever is not firmly lowered or
raised, the media may not be detected.
1
Open the front cover.‫ޕ‬
‫ ޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓ‬
1‫ޓ‬Rigid media‫ޓޓޓޓ‬2‫ޓޓ‬Media feed slot
1
12. Close Front cover.
1
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
1‫ޓ‬Front cover
Name‫ޓޓ‬
‫ޓޓ‬No.
Name
1‫ޓޓ‬Front cover
VJ1626UHE-I-00
10
‫ޓޓޓ‬No.
Name‫ޓ‬
‫ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ‬VJ-1626UH INSTALLATION MANUAL
13. Press down the [-] key on Operation panel for a
while, and check that the rigid media can be fed
no problem.
‫ޓ‬9.2
Loading roll media
5. Loosen the fixing levers of the right and left roll
media holders, move the roll media to the center
and tighten the levers.
NOTE
For removing Media-feed table, read Operation
Manual “3.5.3 Removing Media-feed table
(optional)”
NOTE
Fix the roll media holders by pressing the
holders to the printer.
Media Type
Heater Link
Roll
Origin
Rigid
This section explains how to load roll media.
NOTE
The following roll media can be attached to the
scroller supplied with this unit.
Long Feed
‫࡮ޓ‬Perform checking on the whole surface
of the rigid media.
࡮‫ޓ‬Outer diameter: 150 mm or less
When feeding does not go smoothly, turn the
screws of the front and back casters of
Media-feed table (4 places each) with a spanner
and raise the height slowly to adjust the position
for smoother feeding.
࡮‫ޓ‬Weight: 30 kg or less
4
3
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓ‬
1‫ޓ‬Roll media holder (Left)‫ޓ‬2‫ ޓ‬Roll media holder (Right)‫ޓ‬
3‫ޓ‬Roll media‫ޓޓޓޓ‬4‫ޓޓ‬Fixing lever
࡮‫ޓ‬Length: 50 m or less
Operation Manual “8.1.1 Printer
specifications”
࡮The procedure for loading the roll media is
complete.
‫ޓ‬
‫࡮ޓ‬Set the roll media to the printer continuously as
shown below.
‫ޓ‬Follow the procedure below to load roll media.
9.3 Setting roll media
1. Loosen the fixing levers on the right and left side
of the rear. Set the distance between the roll media
holders wider than the roll media width.
This section explains how to set roll media.
Follow the procedure below to set roll media.
1. Turn the unit ON.
1
1
1
‫ޓޓ‬No.
Name
1‫ޓ‬Caster‫ޓ‬
3
3
࡮‫ޓ‬Tube diameter: 2 or 3 in.
2
4
1
Put the roll media in the center.
2
‫ޓޓޓ‬No.
Name‫ޓ‬
2‫ ޓ‬Screw
1
15.‫ޓ‬Raise Front media loading lever (lower Rear
media loading lever), and put the rigid media back
to the original position.
4
4
Media Type
Heater Link
Roll
Origin
Rigid
‫ޓ࡮ޓ‬Media-feed table is excluded from the
illustration for simplicity.
2
Long Feed
1
1
3
2
‫ ޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓޓ‬
1‫ޓ‬Roll media holder (Left)‫ޓ‬2‫ ޓ‬Roll media holder (Right)‫ޓ‬
3‫ޓ‬Roll media‫ ޓޓޓޓޓޓޓ‬4‫ޓޓ‬Fixing lever
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓ‬
1‫ޓ‬Front media loading ‫ޓ‬
2‫ ޓ‬Rear media loading lever‫ޓ‬
Lever
2. Tighten the fixing lever on the left of Roll media
holder, and fix the Roll media holder (Left).
16. Lower Front media loading lever (raise Rear
media loading lever).
1
17. Use a spanner and tighten the hexagon nuts of the
caster's height adjuster (4 places) toward the
Media-feed table side.
2
3. Set the roll media to the roll media holder (Left).
2
‫ޓ‬
1
1
‫ޓޓ‬No.
Name
‫ޓޓޓ‬No.
1‫ޓ‬Caster height adjuster
Name‫ޓޓ‬
The print head portion may touch the
pressurizing roller portion, and cause a
malfunction.
࡮"Media End" is displayed on the operation panel.
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓޓ‬
1‫ޓ‬Roll media holder (Left)‫ ޓ‬2‫ޓޓޓޓ‬Fixing lever
1
CAUTION
Do not operate the media loading lever
during initial operation and printing.
࡮The printer starts the initializing operation.
1
‫࡮ޓ‬The height of the caster is fixed.
‫ޓ‬
1
2
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓ‬
1‫ޓ‬Roll media holder (Left)‫ ޓ‬2‫ޓޓޓޓ‬Roll media
2. In Panel setup menu, check if the "media type" for
the User type you're going to use is appropriately
set.
‫ޓޓޓޓ‬Operation manual”4.3.2 Menu setup
procedure”
‫ޓޓޓޓ‬Operation manual”5.2.2.10 MediaType
menu”
NOTE
If the type of the media you have loaded
differs from that of the user type you
have set, the media may not be
detected properly.
‫ ޓ‬2‫ޓ‬Hexagon nut
NOTE
After fixing the caster height, even when
Media-feed table is removed, you do not need to
adjust Media-feed table's height in the following
situation.
4. Set the roll media to the roll media holder (Right)
and fixed the fixing lever.
1
3
࡮‫ޓ‬Printer has not been moved
࡮‫ޓ‬Media type has not been changed
࡮The procedure for setting the rigid media is
complete.
2
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
‫ޓޓޓ‬
1‫ޓ‬Roll media holder (Right)‫ ޓ‬2‫ޓ‬
Name‫ޓ‬
Roll media‫ޓ‬
3‫ޓ‬Fixing lever‫ޓ‬
‫ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ‬11‫ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ‬VJ1626UHE-I-00
VJ-1626UH INSTALLATION MANUAL
3. Raise Front media loading lever (lower Rear media
loading lever).
Close the front cover.
NOTE
When setting the roll media, set both sides of the
media at least 5 mm away from the edge of the
pressurizing roller.
Slippage or creases may occur during printing.
2
1
1
OK
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓ‬
1‫ޓ‬Front media loading ‫ޓ ޓ‬2‫ ޓ‬Rear media loading lever
Lever
Bad
2
1
5mm 5mm
࡮"Lever Up" is displayed on the operation panel.
4. Open the front cover.
1
5mm
Bad
2
2
1 5mm
1
‫ ޓ‬No.
Name
1‫ޓ‬Front cover‫ޓޓޓ‬
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓ‬
1‫ޓ‬Roll media‫ޓޓޓޓ‬2‫ޓޓ‬Pressurizing rollers
Name‫ޓ‬
‫ޓ‬
10 Checking printing conditions
Check the condition of the print head after the ink
replenishment.
NOTE
When using 6-color set, use transparent media or
colored media
When you are using 6-color set and printing on
white media, read “3.6.2 Nozzle check B” in the
Operation Manual.
a.Loosen the fixing levers of the right and left roll
media holders, and move the roll media to left or
right.
5.Set the roll media to the media feed slot.
Name
‫࡮ޓ‬The procedure for setting roll media is complete.
8. If the edge of the roll media is set less than 5 mm
from the edge of the pressurizing roller, follow the
procedure below to adjust the position of the roll
media.
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
1‫ޓ‬Front cover
No.
b. After moving the roll media, fix it with fixing
levers of the right and left roll media holders.
NOTE
If the end of the roll media is not wound tightly,
wind it tightly again, and then load it.
1. Turn ON the printer and load the media.
‫“ޓޓ‬9 Setting media”
NOTE
Fix the roll media holders by pressing the holders
to the printer.
If you have moved the roll media to the sides,
repeat the steps 5 to 7.
2
4
1
2. Confirm that the printer functions normally.
3. Press the [<] key on the operation panel for two
seconds or more.
3
1
4
3
Media Type
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name
1‫ޓ‬Roll media‫ޓޓޓޓ‬2‫ޓޓ‬Media feed slot
Heater Link
Roll
Origin
Rigid
3
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name
1‫ޓ‬Roll media holder (Left)‫ޓ‬2‫ ޓ‬Roll media holder (Right)
6. Pull the roll media out about 1 m from the front
media feed slot which is located inside of the front
cover.
Long Feed
3‫ޓ‬Roll media‫ޓޓޓޓޓޓޓ‬4‫ޓޓ‬Fixing lever
‫ޓ‬
9. Lower Front media loading lever (raise Rear media
loading lever).
‫࡮ޓ‬Nozzle check printing starts.
2
NOTE
UV emitted from this product. Minimise
exposure to eyes or skin. Use appropriate
shielding.
1
2
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name
1‫ޓ‬Roll media‫ޓޓޓޓ‬2‫ޓޓ‬Media feed slot
1
7. Rewind the roll media a little by rolling the flange
on the roll media holder while holding the edge of
the media, and eliminate any slack or slant.
NOTE
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name
1‫ޓ‬Front media loading ‫ޓ‬2‫ ޓ‬Rear media loading lever
‫ ޓ‬lever‫ޓ‬
If you rewind the roll media too much, the roll
media may come off from Media feed slot and
may fall on the rear side of the printer.
NOTE
Push Front media loading lever down and lower it
firmly.
If the right edge of the roll media is placed further
right of the loading mark, media detection may
fail, possibly affecting print quality.
CAUTION
UV emitted from this product. Eye or
skin irritation may result from
exposure. Use appropriate shielding.
4. Check the sample print for blurred or missing
parts in the check pattern.
For Rear media loading lever, push it up firmly.
1
If the lever is not firmly lowered or raised, the
media may not be detected.
2
OK
When loading the new roll media, cut the front
edge of the media if it is not straight.
1
‫ޓޓ‬Operation Manual “4.4.3 Cutting media”
Bad
‫ޓޓ‬No.
Name ‫ޓޓޓ‬No.
Name‫ޓ‬
1‫ޓ‬Roll media‫ ޓޓޓޓޓޓޓ‬2‫ޓޓ‬Media loading mark
VJ1626UHE-I-00
12
‫ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ‬VJ-1626UH INSTALLATION MANUAL
5. Check the sample print for blurred or missing
parts in the check pattern.
࡮Press and hold the [Cleaning] key on the operation
panel for two seconds or more.
Media Type
Heater Link
Roll
Origin
Rigid
Long Feed
࡮"Cleaning **%" is displayed on the operation panel.
6. Head cleaning starts.
NOTE
If one time of head cleaning was not enough to
remove blurred or missing parts in the check
pattern, perform powerful cleaning.
If those problems above were not improved after a
few times of head cleaning, refer to the Operation
Manual "7 Troubleshooting" and perform required
procedures.
7.‫ޓ‬Perform nozzle check again and check the
condition of the print head.
11 Manual composition
This product includes the following manuals.
࡮Installation Manual (this manual)
This manual explains the procedures of unpack
ing, assembling, installing, and the basic set up.
࡮Using Quick Reference and Operation
Manual CD
‫ޓ‬This manual explains the procedures of viewing
Quick Reference and Operation Manual which are
contained in the CD-ROM.
࡮ Product Activation Guide
‫(ޓ‬download)
‫ޓ‬This manual explains the procedures when the
printer starts up first time.
࡮Operation Manual (CD-ROM)‫ޓ‬
The Operation Manual explains the basic installa
tion, daily use and applicable functions.
TIP
For viewing Operation Manual, refer to "Using a
Manual CD-ROM" bundled with the printer.
Operation Manual of this product is created with
PDF and HTML format.
Adobe Acrobat Reader 5.0 or above is required to
view PDF format. Adobe Reader is available for
free download at Adobe's website.
HTML format can be viewed using browsers such
as Internet Explorer.
‫ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ‬13‫ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ‬VJ1626UHE-I-00
VJ-1626UH INSTALLATION MANUAL
MEMO
VJ1626UHE-I-00
14
VJ-1626UH INSTALLATION MANUAL
MEMO
15
VJ1626UHE-I-00