C 249 30120 0

OWNER’S MANUAL

ASSEMBLY

‧

OPERATION

‧

MAINTENANCE

WARRANTY

‧

PART ORDERING

CAUTION:

Exercise of a strenuous nature, as is customarily done on this equipment, should not be undertaken without first consulting a physician. No specific health claims are made or implied as they relate to the equipment.

IMPORTANT:

Read all instructions carefully before using this product. Retain this owner’s manual for future reference.

SEARS CANADA INC.

‧ TORONTO , ONTARIO M5B 2B8

TABLE OF CONTENTS

Safety Precautions…………………

Before you begin…………………...

2-3

4

Assembly Instruction……………… 5-9

Treadmill & Monitor Operation…… 10-18

Folding Instruction…………………… 19

Parts list………………………………. 20-23

Overview Drawing………………….. 24

Trouble Shooting……………………. 25

Maintenance ………………………… 26-29

Training guidelines………………….. 30-32

Stretching……..………………………. 33-34

Warranty……………………………… 35

Ordering Replacement parts ………. 36

Service and Parts ……………………. 37

1 ©2012

IMPORTANT SAFETY INFORMATION

THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY

READ ALL INSTRUCTIONS BEFORE USING THIS TREADMILL

CAUTION: Before starting any exercise program, it is recommended that you consult your physician.

WARNING: Connect this unit to a properly grounded outlet only.

DANGER: To reduce the risk of electric shock, always unplug the treadmill from the electrical outlet immediately after using and before cleaning.

WARNING

To reduce the risk of burns, fire, electric shock, or injury to persons :

1. Use 120 volt a.c. household current on a dedicated circuit.

Grounding Instructions

This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

See diagram below for grounding methods.

2. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions.

3. The use of an extension cord with this product is not recommended. If an extension cord is needed, use a short (less than

10 feet) heavy gauge (14 gauge or better) extension cord with a three prong (grounded) plug and receptacle.

4. Never leave the treadmill unattended when plugged in. Remove the safety key and unplug the unit from the outlet when not in use and before removing or replacing parts.

5. Never operate the treadmill if it has a damaged cord or plug, if it is not working properly, if it has been dropped, damaged, or exposed to water. Never move the treadmill belt while the power is turned off.

6. Do not pull the treadmill by the power supply cord or use cord as a handle. Keep cord away from heated surfaces and open flames.

7. Fitness equipment must always be installed and used on a flat surface. Do not use outdoors or near water. Do not place the unit on a loose rug or uneven surface. It is recommended to use an equipment mat to prevent the unit from moving while it is being used, which could possibly scratch or damage the surface of your floor. It is recommended to have a minimum of 3 metres safe clearance on all sides of the treadmill while in use.

8. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage, covered patio or near water.

9. Do not operate the treadmill where aerosol products are used or where oxygen is being administered.

10. Read, understand and test the emergency stop procedure before using the treadmill (see operation and adjustment on page

12)

11. Do not insert any objects into any openings.

12. Inspect and properly tighten all parts of the treadmill regularly.

13. Keep children and pets away from this equipment at all times while exercising.

14.Handicapped individuals should have medical approval and close supervision when using this treadmill.

15. Do not place hands or feet under the treadmill. Always keep hands and legs off of the treadmill when others are using it.

16. Never turn on treadmill while standing on treadbelt. Always hold the handrails while using the treadmill. Always return the treadmill to the slowest speed to provide for safe dismount and low speed restart.

17. To disconnect, turn all controls to the off position, then remove plug from outlet.

18.Do not attempt to raise, lower or move the treadmill until it is properly assembled. See assembly on page 5 and to fold and move the treadmill on page 19. Care must be taken when lifting or moving the equipment, so as not to injure your back.

Always use proper lifting techniques. You must use any attachments that are not recommended by the manufacturer.

2 ©2012

19. Use the treadmill only for its intended use as described in this manual. Do not use any attachments that are not recommended by the manufacturer.

20. User weight should not exceed 285lbs (130 kg).

21. Never allow more than one person on the treadmill at once.

22. Warm up 5 to 10 minutes before each workout and cool down 5 to 10 minutes afterward. This allows your heart rate to gradually increase and decrease and will help prevent straining muscles.

23. Never hold your breath while exercising. Breathing should remain at a normal rate in conjunction with the level of exercise being performed.

24. Start your program slowly and very gradually increase your speed and distance.

25. Always wear suitable clothing and footwear while exercising. Do not wear loose fitting clothing that could become entangled with the moving parts of your treadmill. Do not walk or jog barefoot, in stocking feet or loose fitting shoes or slippers.

26. This treadmill is intended for in-home use only. Do not use the treadmill in any commercial, rental or institutional setting.

▲ WARNING: Before beginning any exercise program consult your physician. This is especially important for individuals over the age of 35 or persons with pre-existing health problems. Read all instructions before using any fitness equipment. We assume no responsibility from personal injury or property damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

3 ©2012

Before you begin.

Thank you for purchasing our product. Even though we go to great efforts to ensure the quality of each product we produce, occasional errors and /or omissions do occur. In any event should you find this product to have either a defective or a missing part please contact us for a replacement.

This product has been designed for home use only. Product liability and guarantee conditions will not be applicable to products being subjected to professional use or products being used in a gym center.

This exercise equipment was designed and built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before assembly and operation of this machine.

Before reading further, please familiarize yourself with the parts that are labeled in the drawing below

Console assembly

Safety Key

Speed Adjustment switch

On / off switch

Breaker

Motor cover

Pulse sensors

Incline Adjustment Switch

Upright

Walking belt

Locking Knob

Wheels

Maximum User weight 285 LBS (130 KG)

Frame

4

Adjustment bolts

©2012

Assembly

I t will take two people to assemble your unit.

Set the treadmill in a cleared area and remove all packing material. Do not dispose of the material until your assembly is completed. Note: The underside of your treadmill’s walking belt is coated with a lubricant. During shipping, a small amount of lubricant may be transferred to the top of the waling belt or the shipping carton. This does not affect the treadmill’s performance. If you notice any lubricant on the top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non abrasive cleaner.

For the sake of familiarizing yourself with the parts identified in the instructions, first study the overview drawing.

Assembly only requires the included wrenches.

HARDWARE PACK

#110.

Ø5/16" × 19 × 1.5T

Flat Washer (4pcs)

#95.

Ø5/16" × 19 × 1.5T

Curved Washer (2pcs)

#89.

5 × 16m/m

Tapping Screw (6pcs)

#111.

M5 × 15m/m

Phillips Head Screw (8pcs)

#128.

M5

Speed Nut Clip (6pcs)

#94.

5/16" × 15m/m

Button Head Socket Bolt (14pcs)

#102 .

Safety Key (1pc)

#98 . M6 (66 × 88)

Allen Wrench (1pc)

#93.

Lubricant (1pc)

#97.

Combination M5 Allen Wrench &

Phillips Head Screw Driver (1pc)

5 ©2012

ASSEMBLY INSTRUCTIONS

Step1.

Take out Treadmill from carton and place it on smooth ground.

Step 2.

Slide the lower computer wire (38) into the right upright (4).

38

4

Step3.

Lift the right upright (4) upward. Fasten the right upright (4) to the frame base (2) using four 5/16" ×15 mm button head bolts (94).

Repeat for the left upright (5). Use the combination M5 allen wrench & Phillips head screw driver (97).

NOTE: Ensure that the wire is safely inserted in the upright to avoid pinching the computer wire.

4

94

94

97

5

94

94

2

6 ©2012

Step 4.

1.

Install the 6pcs of M5 Speed Nut Clips (128) on the Frame Base left and right side.

2. Slide the Frame Base Covers (R , L)(43 , 44) onto the Right and Left Uprights (4,5) to the Frame Base (2) and secure using 6pcs of 5 × 16m/m Tapping Screws (89) with the help of the Combination M5 Allen Wrench & Phillips

Head Screw Driver (97).

128

128

128

128

128

128

43

44

89

97

89

43

89

44

89

7

89

89

©2012

Step5.

Connect the computer cable (38) from the right upright to the upper computer cable (36).

36

38

Step 6.

Fasten the console support (6) into the right and left uprights (4 / 5). Secure the right upright (4) using three 5/16" ×15m/m button head bolts (94), two 5/16" × 19 × 1.5T flat washers (110) and one

5/16" × 19 × 1.5T curved washer (95) by using the combination M5 allen wrench and Phillips head screwdriver (97). Repeat for the left upright (5).

6

95

94

110

110 94

110

95

110 94

5

4

97

Step 7.

Attach the fan assembly (112) onto the console support (6). Secure using four M5 x 15m/m phillips head screws (111) using the combination M5 allen wrench & Phillips head screwdriver (97).

6

111

112

8 ©2012

Step 8.

Connect the upper computer cable (36) to the console assembly (39).

Connect the speed adjustment switch w/cable (25) to the console assembly (39).

Connect the incline adjustment switch w/cable (26) to the console assembly (39).

Connect the handpulse assembly wire (27) to the console assembly (39).

39

27

26

112-3

36

25

27

Step 9.

Install the console assembly (39) onto the console support (6) with four M5 × 15m/m phillips head screws (111) by using Combination M5 Allen Wrench & Phillips Head Screw Driver (97 ).

NOTE: ENSURE THAT ALL NUTS AND BOLTS ARE FIRMLY TIGHTENED.

9 ©2012

TREADMILL OPERATION

Your treadmill features a walking belt coated with a lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or walking board. Such substances will deteriorate the walking belt and cause excessive wear.

How to plug in the power cord.

GROUNDING INSTRUCTIONS.

This product must be grounded. No plug adapter should be used with this product.

WARNING: Improper connection of the equipment grounding conductor can result in a risk of an electric shock. Check with a qualified electrician if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product, if it will not fit the outlet; have a proper outlet installed by a qualified electrician. The use of an extension cord with this product is not recommended. If an extension cord is needed, use a short (less than 10 feet) heavy gauge (14 gauge or better) extension cord with a three prong (grounded) plug and receptacle. IMPORTANT: If the power cord is damaged, it must be replaced with a manufacturer recommended power cord.

1.

Plug the indicated end of the power cord into the socket of the treadmill. See drawing below

2.

Plug the power cord into an appropriate outlet that is properly installed and grounded. See drawing below.

Important: The treadmill is not compatible with GFCIequipped outlets.

Note: Your power cord and outlet may appear different

CAUTION: Before operating the console, read the following precautions:

• Do not stand on the walking belt when turning on the treadmill

• Always wear the safety key

• Adjust the speed in small increments to avoid sudden jumps in speed

• To reduce the possibility of electric shock, keep the console dry. Avoid spilling liquids on the console and place only sealed water bottles in the water bottle holders.

10 ©2012

TO OPERATE TREADMILL

CAUTION: To avoid injury, hold onto the handrails while mounting and dismounting the treadmill.

Hold onto the handrails and place feet on siderails before starting. Step onto the walking belt only a slowest speed.

Note: Before operating your treadmill, become familiar with all operating parts and controls - their location and function see figure on page 4. Also before operating the console make sure that the power cord is properly plugged in and the on / off button is on.

COMPUTER OPERATION INSTRUCTIONS

CAUTION: Before operating the console, read the following precautions:

• Do not stand on the walking belt when turning on the treadmill

• Always wear the safety key

• Adjust the speed in small increments to avoid sudden jumps in speed

• To reduce the possibility of electric shock, keep the console dry. Avoid spilling liquids on the console and place only sealed water bottles in the water bottle holders.

TO OPERATE TREADMILL

CAUTION: To avoid injury, hold onto the handrails while mounting and dismounting the treadmill.

Hold onto the handrails and place feet on siderails before starting. Step onto the walking belt only a slowest speed.

Before operating the console make sure that the power cord (32) is properly plugged in and the on / off button (30) is on. Attach the magnet end of the safety key ( 102 ) onto the monitor and attach the clip end of the safety key ( 102 ) to your clothing (ie: waistband). If you should slip or fall while exercising the safety key will pull out of the console, shutting off the treadmill .

11 ©2012

Getting started:

Power the treadmill on by plugging it into an appropriate wall outlet, then turn on the power switch located at the front of the treadmill below the motor hood.

When the power is turned on, all the lights on the display will light for a short time. A message will scroll across screen showing the current software version. The treadmill will then enter idle mode, which is the starting point for operation.

Function Buttons on monitor:

5 preset incline: 2%, 4%, 6%, 8%, 10%

Press your desired incline position and the treadmill will automatically adjust to your preset incline.

5 preset speed: 2 mph, 4 mph, 6mph, 8mph, 10mph

Press your desired speed and the treadmill will automatically adjust to your preset speed.

Speakers: The console has a built-in Speakers. You may Plug an Audio Source (CD player,

MP3, Computer ,etc.) into the Jack on the right side of console. There is no volume control on console, volume must be controlled by Audio Source.

Incline

Select:

▲▼ : Press the ▲ button to raise the incline position. The maximum incline position is

15.

Press the ▼ button to lower the incline position. The minimum incline position is

0.

Press to generate new programs. Press the “select” button during a the random program to display between the speed only profile, incline only profile or between speed and incline profiles.

Program: Press to select your desired program; manual, random program, 5 users and 2 Heart rate control.

Press the “stop” button to stop your treadmill Stop:

Start:

Enter/display :

Press the “start” button to start your treadmill.

Press the “enter” button to accept the function value.

Press the “enter” during the exercise program to change the display.

Speed ▲▼ ▲ button to increase the speed of the treadmill. The maximum speed is

10 mph.

Press the ▼ button to decrease the speed of the treadmill. The minimum speed is .6 mph

The console has a built in fan. Press the fan button to turn on or off. Fan:

12 ©2012

Function Buttons on handrail tubes:

Fast:

Slow:

Up:

Down:

Press the “fast” button to increase your speed from 0.6 mph (1kmph ) to 10mph (16kmph).

Press the “slow” button to decrease your speed from 10mph (16kmph) to .6 mph (1kmph).

Press the “up” button to raise the incline position. The maximum incline position is 15.

Press the “down” button to lower the incline position. The minimum incline position is 0.

Monitor display

Pulse: Displays the user’s current heart rate in beats per minutes during the workout.

To display your heart rate, you must hold both handrails.

Note: This is a rough guide used for comparison of different exercise sessions, which cannot be used for medical purposes.

Time:

Calories:

Displays your elapsed workout time in minutes up to 99:59

Counts down from your preset target time to 00:00 during your workout

Displays the cumulative calories burned at any given time during your workout.

Counts down from your preset target calories to 0 during your workout.

Note: This is a rough guide used for comparison of different exercise sessions, which cannot be used for medical purposes.

Distance: Displays the distance traveled in mile

Counts down from your preset target distance to 0

Incline:

Program:

Speed:

Displays the incline position from 0 to 15

Displays the program you selected.

Display the current speed in miles per hour from 0.06 to 10 mph

Quick-Start Operation:

STEP 1: Install safety key on the monitor.

STEP 2: Press Start key to start belt movement , at .6 mph (1.0kmph), then adjust to the desired speed using the speed button (console or hand rail). You may also use the rapid speed keys 2 through 10 to adjust the speed.

STEP 3: To slow tread-belt press the speed down key (console or hand rail) to decrease to your desired speed. You may also press the rapid speed adjust keys, 2 through 10.

STEP 4: To stop the tread-belt press and release the Stop key.

13 ©2012

Programmable Features

The monitor offers one manual program, random, 5 user defined programs and 2 H.R.C. programs. The included user programs (User 1 to User 5) are for custom workouts.

To Select a Program:

STEP 1: Press the desired PROGRAM key. Press enter to select the manual program. The display will prompt you through the programming or you can just press Start to begin the program with default values.

Note : At any time during these steps press stop to return to the previous step.

STEP 2: The window will now be blinking a value, which is your Body Weight . Entering the correct body weight will affect the calorie count. Use the Up/Down keys to adjust, then press enter.

A note about the Calorie display: No exercise machine can give you an exact calorie count because there are too many factors which determine exact calorie burn for a particular person.

Even if someone is the exact same body weight, age and height, their calorie burn may be very different than yours. The Calorie display is to be used as a reference only to monitor improvement from workout to workout.

STEP 3: The window will now be blinking a value, which is your Age. Entering your correct age affects the heart rate control programs. Use the Up/Down keys to adjust, then press enter.

Your age determines the maximum heart rate you may achieve. Since the Heart Rate control features are based on a percentage of your maximum heart rate, it is important to enter the correct age for these features to work properly.

STEP 4: The window will blink and you need to choose one of the select factors; time, distance or calories, in which to count down from. Press the select button to confirm time, distance or calories as your factor. Use up/down keys to adjust the selected factor of; time, distance or calorie then press enter.

STEP 5: Press start to begin.

Heart Rate Control Operation

CAUTION! You must receive a strong / steady value in heart rate window.

STEP 1: Press HR1 or HR2 button.

HRC1 adjust the speed to keep the heart rate at the target value

HRC2 adjust the incline to keep the heart rate at the target value

STEP 2: The Pulse window will be blinking, showing the default HR for this program. You may adjust it and press enter if you want or just press enter to accept the default value.

STEP 3: The Calorie will now be blinking showing bodyweight. Adjust and press enter or press enter to accept default.

STEP 4: The Pulse window will now be blinking showing age. Adjust and press enter or press enter to accept default.

STEP 5: The Time window will now be blinking. Adjust the time and press enter.

STEP 6: Press Start to begin program.

Note: You may change the target heart rate value. The target heart rate value will be in the range of

55%~85% value calculated by the program according to the age you have entered. You can increase or decrease the target value as what fits you. Consulting your physician to determine the proper value before setting is recommended. Press START to begin your workout

14 ©2012

Random Program

This mode which is a profile includes speed and incline automatically generated by the program. The user can continually choose the profiles until the one which is satisfied. It can also save the USER mode and make adjustments until a most suitable profile is reached. The operation is as follows:

A.

Use PPROGRAM button to select RANDOM PROGRAM mode and press ENTER to profile selection.

B.

Now the dot matrix will display speed profile for 5 seconds then switch to incline profile for another 5 seconds and recycle. Press ENTER to select the profile and forward to enter next parameter. Press

SELECT button to generate new profile. This step can be continued until ENTER is pressed.

C.

Now the value of the weight is displayed. Use FAST/SLOW buttons to adjust the weight and press

ENTER for next setting.

D.

Now the value of the age will be displayed. Use FAST/SLOW buttons to adjust the age and press

ENTER for next setting.

E.

Now the preset time 20:00 will be displayed. Use FAST/SLOW buttons to adjust for proper time duration and press START to start the treadmill.

F.

The profile can be saved as an USER profile when the workout is finished. The USER can be adjusted whenever is necessary.

User Programs:

STEP 1: Select the user you desire. User 1 through User 5 via the PROGRAM key then press Enter .

Note that the dot matrix display portion will have a single row of dots at the bottom (Unless there is a previously stored program. If you have it saved, the monitor will ask you to override the save user file.

STEP2: Use UP/DOWM buttons to switch the user names. Use NAME to enter the user name with

FAST/SLOW buttons to enter characters A~Z. There are no more than 7 characters to enter.

Press STOP after entering the last character and exit.

STEP 3: The window will now be blinking a bodyweight value. Enter your bodyweight using the fast/slow keys and press Enter.

STEP 4: The window will now be blinking an Age value. Adjust the age using the fast/slow keys and press enter.

STEP 5: The window will now be blinking 30:00 as the preset time.

Use the fast/slow keys to adjust the time. Press ENTER key.

STEP 6: The first column (segment) will now be blinking. Using the Fast / Slow keys, adjust the speed level to your desired effort for the first segment then press enter. The second column will now be blinking. Repeat the above process until all segments have been programmed. The first column will be blinking again. This is for the incline programming. Repeat the above process to program all segments for incline.

STEP 7: Press the Start button to begin the workout and also save the program to memory.

15 ©2012

MUSCLE ACTIVATION FIGURE

There is an anatomical figure located at the top of the console. This figure will light all areas that are activated when using the treadmill. These will light up during any of the programs. You can control which muscles are activated by changing the incline and swinging your arms. The pre-set programs will determine which lower body muscles will be activated by automatically adjusting the incline. Generally the following guidelines hold true:

• The upper body LED’s will light any time your hands aren’t in contact with the pulse grip sensors

• The lower body lights will activate in three degrees of engagement:

Green represents minimal muscle involvement,

Amber represents medium involvement, and Red represents full or heavyactivation.

• 0-4.5% Elevation: even muscle distribution, all four muscle groups will be Amber

• 5-15% Elevation: Quads are Amber and Glutes, Hamstrings, and Calves are Red

HEART RATE % PROFILE

The console LCD screen will display your current heart rate anytime a pulse is detected. The Bar Graph, located to the right of the LCD screen, will show your current heart rate % in relation to your projected maximum heart rate, which is determined by your age that you entered during the programming phase of any of the 10 programs. The significance of the bar graph colors are as follows:

• 50-60% of maximum is Amber

• 65-80% of maximum is Amber and Green

• 85-90% or more is Amber, Green, and Red

16 ©2012

Heart Rate Programs

The old motto, “no pain, no gain”, is a myth that has been overpowered by the benefits of exercising comfortably. A great deal of this success has been promoted by the use of heart rate monitors.

With the proper use of a heart rate monitor, many people find that their usual choice of exercise intensity was either too high or too low and exercise is much more enjoyable by maintaining their heart rate in the desired benefit range.

To determine the benefit range in which you wish to train, you must first determine your

Maximum Heart Rate. This can be accomplished by using the following formula: 220 minus your age.

This will give you the Maximum Heart Rate (MHR)for someone of your age. To determine the effective heart rate range for specific goals you simply calculate a percentage of your MHR. Your Heart rate training zone is 50% to 90% of your maximum heart rate. 60% of your MHR is the zone that burns fat while 80% is for strengthening the cardio vascular system. This 60% to 80% is the zone to stay in for maximum benefit.

For someone who is 40 years old their target heart rate zone is calculated:

220 – 40 = 180 (maximum heart rate)

180 x .6 = 108 beats per minute

(60% of maximum)

180 X .8 = 144 beats per minute

(80% of maximum)

So for a 40 year old the training zone would be 108 to 144 beats per minute.

If you enter your age during programming the console will perform this calculation automatically. Entering your age is used for the Heart Rate programs. After calculating your MHR you can decide upon which goal you would like to pursue.

The two most popular reasons for, or goals, of exercise are cardiovascular fitness (training for the heart and lungs) and weight control. The black columns on the chart above represent the MHR for a person whose age is listed at the bottom of each column. The training heart rate, for either cardiovascular fitness or weight loss, is represented by two different lines that cut diagonally through the chart. A definition of the lines’ goal is in the bottom left-hand corner of the chart. If your goal is cardiovascular fitness or if it is weight loss, it can be achieved by training at 80% or 60%, respectively, of your MHR on a scheduleapproved by your physician. Consult your physician before participating in any exercise program.

17 ©2012

Rate of Perceived Exertion

Heart rate is important but listening to your body also has a lot of advantages. There are more variables involved in how hard you should workout than just heart rate. Your stress level, physical health, emotional health, temperature, humidity, the time of day, the last time you ate and what you ate, all contribute to the intensity at which you should workout. If you listen to your body, it will tell you all of these things.

The rate of perceived exertion (RPE), also know as the Borg scale, was developed by Swedish physiologist G.A.V. Borg. This scale rates exercise intensity from 6 to 20 depending upon how you feel or the perception of your effort.

The scale is as follows:

Rating Perception of Effort

6 Minimal

7 Very,very light

8 Very,very light +

9 Very light

10 Very light +

11 Fairly light

12 Comfortable

13 Somewhat hard

14 Somewhat hard +

15 Hard

16 Hard +

17 Very hard

18 Very hard +

19 Very,very hard

20 Maximal

You can get an approximate heart rate level for each rating by simply adding a zero to each rating.

For example a rating of 12 will result in an approximate heart rate of 120 beats per minute.

Your RPE will vary depending up the factors discussed earlier. That is the major benefit of this type of training. If your body is strong and rested, you will feel strong and your pace will feel easier. When your body is in this condition, you are able to train harder and the RPE will support this. If you are feeling tired and sluggish, it is because your body needs a break. In this condition, your pace will feel harder. Again, this will show up in your RPE and you will train at the proper level for that day.

18 ©2012

FOLDING AND MOVING YOUR TREADMILL

Before folding the treadmill, ensure that the treadmill is at it’s lowest incline position. Turn the power switch off, located on the front of the motor cover and unplug the power cord.

CAUTION: You must be able to safely lift 20 kg (45lbs) in order to raise and lower the treadmill.

To decrease the possibility of injury, bend your legs and keep your back straight while you are raising or lowering your treadmill.

To protect the floor or carpet from damage, place a mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85 degrees

Fahrenheit.

Unfolding

Hold the treadmill running deck with left hand. Pull the locking knob with your right hand and slowly lower the treadmill running deck. The deck will lower unassisted when it reaches about waist high.

Folding

Lift the treadmill running deck with your left hand and slowly raise the treadmill running deck until the treadmill is locked by the locking knob.

Moving

Before moving the treadmill, fold the treadmill to the stored position as described above. Hold the upper ends of the handrails and slowly move the treadmill to your desired location.

To reduce the risk of injury, use extreme caution while moving the treadmill, do not attempt to move the treadmill over an uneven surface.

19 ©2012

PARTS LIST

Key No Part No

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

27~2

27~3

28

29

30

31

32

33

Description

286001 Main Frame

286002

Frame Base

286003

Incline Bracket

286004

Right Upright

286005

Left Upright

286006

Console Support

286007

Outer Slide

286008

Inner Slide

286009

Locking Knob

286010 Frame Cover

286011

Belt Guide

286012

Running Deck

286013

Running Belt

286014

Drive Belt

286015

Front Roller W/Pulley

286016

Rear Roller

286017

Sleeve for Frame Base Front Wheel

286018

Magnet

286019

Cylinder

286020

PVC Handgrip

286021

Wire Tie Mount

286022

Drive Motor

286023

Incline Motor

286024

Controller

286025

Speed Adjustment Switch W/Cable

286026

Incline Adjustment Switch W/Cable

286027

286027-2

Handpulse Assembly

Handpulse Top Cover (W/Cable)

286027-3 Handpulse Bottom Cover

286028

Breaker

286029

Power Socket

286030 On/Off Switch

286031

1000m/m_Sensor W/Cable

286032 Power Cord

286033 300m/m × 764 × 764_Connecting Wire (White)

20

Q'ty

1

1

1

1

1

1

2

5

1

2

1

1

1

1

1

1

1

2

1

1

1

1

1

1

1

1

1

1

1

2

2

2

1

1

1

©2012

62

63

64

58

59

61

65

49

50

53

55

56

46

47

48

43

44

45

39~22

39~23

40

41

42

39~2

39~5

39~8

39~9

39~10

39~11

39~12

39~13

39~21

34

35

36

38

39

39~1

286034 300m/m × 764 × 764_Connecting Wire (Black)

286035 100m/m × 764 × 764_Connecting Wire (Black)

286036

Computer Cable (Upper)

286038

Computer Cable (Lower)

286039

Console Assembly

286039-1

Console Top Cover

286039-2

Console Bottom Cover

286039-5

300m/m_Safety Switch Module W/Cable

286039-8 3 × 10m/m_Sheet Metal Screw

286039-9 500 m/m_Amplifier Cable

286039-10

Amplifier Controller

286039-11

250m/m_Speaker W/Cable

286039-12

286039-13

750m/m_Speaker W/Cable

300m/m_Sound Board W/Cable

286039-21

Speaker Grill Anchor

286039-22

400m/m_Console Ground Wire

286039-23

M5 × 6m/m_Phillips Head Screw

286040 Drink Bottle Holder (R)

286041 Drink Bottle Holder (L)

286042

Button Head Plug

286043

Frame Base Cover (R)

286044

Frame Base Cover (L)

286045

Frame Base Front Wheel

286046

Frame Base Rear Wheel

286047

Motor Cover Anchor

286048 Motor Top Cover

286049

286050

Top Motor Cover Plate

□ 30 × 60m/m_Square End Cap

286053 Foot Rail

286055

Rear Adjustment Base (L)

286056

Rear Adjustment Base (R)

286058

Cushion

286059

Rear Up/Down Adjustable Foot

286061 Ø10 × Ø24 × 3T_Nylon Washer (A)

286062 Ø50 × Ø13 × 3T_Nylon Washer (B)

286063

1/2" × 1-1/4"_Carriage Bolt

286064

1/2" × 1"_Hex Head Bolt

286065 3/8" × 4-1/2 "_Hex Head Bolt

21

1

2

2

1

2

1

1

6

1

1

1

1

8

1

1

1

1

1

1

1

1

1

1

1

2

2

1

2

3

4

2

2

1

1

6

5

1

1

©2012

86

87

89

82

83

85

77

78

79

80

81

74

75

76

71

72

73

66

67

68

69

70

98

100

102

103

104

105

106

107

93

94

95

90

91

92

96

97

286066 3/8" × 92m/m_Hex Head Bolt

286067

3/8" × 1"_Hex Head Bolt

286068 3/8" × 1-1/2"_Hex Head Bolt

286069

3/8" × 45m/m _Hex Head Bolt

286070 3/8" × 2"_Flat Head Socket Bolt

286071 5/16" × 1"_Button Head Socket Bolt

286072

M8 × 60m/m_Hex Head Bolt

286073 M8 × 80 m/m_Socket Head Cap Bolt

286074 M8 × 25m/m_Flat Head Countersink Bolt

286075

1/2" × 8T_Nyloc Nut

286076 3/8" × 7T_Nyloc Nut

286077 5/16" × 6T_Nyloc Nut

286078

M8_Nyloc Nut

286079 3/8" × 7T_Nut

286080

Ø35 × 5/16" × 1.5T_Flat Washer

286081

Ø25 × 10 × 2.0T_Flat Washer

286082 Ø19 × 10 × 1.5T_Flat Washer

1

4

2

1

2

4

1

2

6

4

6

2

1

3

2

4

6

286083

3/8" × 2.0T_Split Washer

286085 M5_Star Washer

286086 4 × 12m/m_Sheet Metal Screw

286087

5 × 16m/m_Tapping Screw

4

3

12

27

286089 5 × 16m/m_Tapping Screw

286090 3.5 × 12m/m_Sheet Metal Screw

17

17

286091

286092

4 × 38m/m_Sheet Metal Screw

3.5 × 16m/m_Tapping Screw

2

5

286093 Lubricant 1

286094

5/16" × 15m/m _Button Head Socket Bolt

286095 Ø5/16" × 19 × 1.5T_Curved Washer

286096

M5 × 10m/m_Phillips Head Screw

286097

Combination M5 Allen Wrench & Phillips Head Screw Driver

286098 M6(66×86mm)_L Allen Wrench

2860100

3 × 20m/m_Tapping Screw

2860102 800m/m_Square Safety Key

2860103 □ 21.4 × 21.4 m/m_Square End Cap

2860104 □ 25.4 × 25.4 m/m_Square End Cap

2860105 3 × 10 m/m_Sheet Metal Screw

2860106 M5_Split Washer

2860107

Sensor Rack

14

2

3

1

1

4

1

1

1

2

3

1

22 ©2012

110

111

112

112~1

112~2

112~3

113

114

117

119

120

121

122

123

124

125

126

127

128

129

130

2860110

Ø5/16" × 19 × 1.5T_Flat Washer

2860111 M5 × 15m/m_Phillips Head Screw

2860112

Fan Assembly

2860112-1

Top Fan Cover

2860112-2

Bottom Fan Cover

2860112-3

Fan

2860113 Handgrip End Cap

2860114

Round Cap

2860117

1820m/m_Audio Cable

2860119

Copper Foil

2860120 Ø6.5 × Ø25 × 1.5T_Concave Washer

2860121

4 × 19m/m_Sheet Metal Screw

2860122 M8 × 50m/m_Flat Head Countersink Bolt

2860123 Non-Slip Rubber

2860124

Deck Cross Brace

2860125

Motor Bracket

2860126 M8 × 12m/m_Hex Head Bolt

2860127

M8 × 1.5T_Split Washer

2860128

2860129

M5_Speed Nut Clip

Ø1/4"_Wire Clamp

2860130 1000m/m_Ground Wire

23 ©2012

1

1

2

2

4

2

2

1

1

8

1

1

2

2

1

1

4

8

6

1

1

EXPLODED DIAGRAM

24 ©2012

TROUBLE SHOOTING

Problem Cause

Treadmill will not start Treadmill not plugged in

Correction

Plug into three prong (grounded) outlet

On / off switch not on

House circuit breaker tripped

Push the on/off button to on

Reset or replace

Treadmill reset switch tripped Reset treadmill reset switch see reset switch resetting

Replace fuse - see fuse replacement Treadmill motor controller fuse or incline controller fuse blown

Unit plugged into insufficient extension cord

Plug directly into wall outlet

House circuit breaker tripped Reset or replace Treadmill stop or shuts off by itself

Treadmill reset switch tripped

Treadmill motor controller fuse blown

Reset treadmill reset switch

Replace controller

Treadbelt does not run in center

Treadbelt slips

Treadbelt hesitates while being stepped on

Black particles collecting under treadmill

Treadbelt tension not even across treadbelt

See treadbelt adjustment

Treadbelt tension too loose See treadbelt adjustment

Insufficient lubricant on treadbelt

See treadbelt lubrication

Drive belt is breaking in Vacuum under treadmill periodically

No display on monitor On / off switch not on

Monitor displays Lost speed

Reed switch not aligned properly

Magnet damaged or missing from front roller pulley

Push on / off button to on

See reed switch adjustment

Replace magnet

Monitor not working properly Replace monitor

No pulse displayed on monitor

Hands not on hand pulse Place two hands on hand pulse

Hands on hand pulse Replace hand pulse

NOTE: It is not necessary to return treadmill for a monitor repair. The monitor or console is removable from the treadmill for repair or replacement - see parts section

25 ©2012

MAINTENANCE INSTRUCTIONS

TREADBELT ADJUSTMENT

The treadbelt has been factory pre-adjusted, however if during the operation:

If Treadbelt slips

Treadbelt slips during use if the treadbelt is too loose : a) Tighten both rear roller adjusting bolts a 1/4 turn clockwise using allen wrench.

Treadbelt shifts too far to the right a) Set the treadmill speed to 3.5 M.P.H. b)

Tighten the right adjusting bolt a 1/4 turn clockwise

using allen wrench. c) Wait 15 seconds: if no change; turn the left adjusting

bolt (100) a 1/4 turn counter-clockwise using allen

wrench. e) Repeat steps b and c until belt is centered

Treadbelt shifts too far to the left a) Set the treadmill speed to 3.5 M.P.H. b) Tighten the left adjusting bolt a 1/4 turn clockwise

using allen wrench. c) Wait 15 seconds: if no change; turn the right adjusting

bolt (100) a 1/4 turn counter-clockwise using allen

wrench. e) Repeat steps b and c until belt is centered

1/4 TURN

1/4 TURN

If Treadbelt shifts too far to the left

IMPORTANT

DO NOT OVERTIGHTEN TREADBELT

If treadbelt is over-tightened, edges of treadbelt will begin to curl

CAUTION!! DO NOT ALLOW ANYONE TO WALK

ON TREADBELT WHILE YOU ARE ADJUSTING.

1/4 TURN

26 ©2012

MAINTENANCE INSTRUCTIONS

CLEANING

Care has been taken to assure that your treadmill has been properly adjusted and lubricated at the factory. It is not recommended that the user attempt service on the internal components instead seek service from an authorized service center. However, from time-to-time the outer surfaces may appear dull or dirty, following the instructions listed below will restore and preserve the original finish.

Note: Always unplug your treadmill prior to cleaning in order to avoid electrical hazard or shock.

1. Cleaning metal surfaces may be accomplished by using a soft cotton or terry cloth rag with a light application of car wax. Do not use aerosol sprays or pump bottles as they may deposit wax upon the walking or computer surface.

2. Under no circumstances are you to use ammonia, oils, silicones or any other compounds on the rubberized walking surface. The use of such materials may cause serious injury to the body and/or deteriorate the performance of the walking surface. Only clean the rubberized walking surface with a damp cloth (water only).

3. From time-to-time the computer surface may collect dust or finger prints. The use of harsh chemicals will destroy the protective coating and cause a static build up that will damage the components. This surface may be cleaned with specially prepared chemicals found in most computer supply stores especially made for anti-static surfaces. It is strongly recommended that you purchase such a cleaning compound.

27 ©2012

MAINTENANCE INSTRUCTIONS

TREADMILL LUBRICATION

Your treadmill should require little maintenance other then periodically applying lubricant. Lubricating under the treadbelt will ensure superior performance and extend its life expectancy.

HOW TO CHECK TREADBELT FOR PROPER LUBRICATION

1- Monitor will display a message prompting you to lubricate the treadmill after the treadmill has a total of 60 miles accumulated or up to 90 hours of running time. After two messages, the message prompting you to lubricate the treadmill will be removed.

2- Lift one side of the treadbelt and feel the top surface of the treadboard

If the surface is slick to the touch, then no further lubrication is required

If the surface is dry to the touch, apply one packet of lubricant or half of the bottle of lubricant.

HOW TO APPLY LUBRICANT

1. Lift one side of treadbelt.

2. Pour one half of the lubricant bottle under the center of the treadbelt on the top surface of the treadboard

3. Walk on the treadmill at a slow speed for 3 to 5 minutes to evenly distribute lubricant.

NOTE: DO NOT over lubricate treadboard. Any excess lubricant that comes out should be wiped off.

IMPORTANT: ONLY USE HALF THE BOTTLE OF LUBRICANT PER APPLICATION

LUBRICATION SCHEDULE

We recommend that you use:

LUBE-N-Walk™ Treadmill Lubrication Kit, available from Sears parts and service.

28 ©2012

RESET SWITCH RESETTING

If your treadmill looses power or will not start, check the reset switch located on the front of the motor cover.

If the white tab of the reset switch is not showing then the reset switch has not been tripped.

If the white tab of the reset switch is showing, the reset switch has tripped.

To reset the reset switch:

Remove the safety clip on console.

Press white tab of the reset switch in until it snaps back into place.

If the reset switch continues to trip - see treadbelt adjustment and treadbelt lubrication

SPEED SENSOR ADJUSTMENT

If the monitor does not display speed or distance the speed sensor and magnet may be misaligned. Follow these step to check and realign.

Remove the motor cover

Check the spacing and alignment between the magnet on the right side of the front roller and the speed sensor on the frame. The spacing must be 1/8”.

Loosened screw and slide speed sensor in or out of clamp.

Retighten screw

Replace the motor cover

29 ©2012

TRAINING GUIDELINES

Exercise is one of the most important factors in the overall health of an individual. Listed among its benefits are: x Increased capacity for physical work (strength endurance) x Increased cardiovascular (heart and arteries/veins) and respiratory efficiency x Decreased risk of coronary heart disease x Changes in body metabolism, e.g. losing weight x Delaying the physiological effects of age x Physiological effects, e.g. reduction in stress, increase in self-confidence, etc.

Basic Components of Physical Fitness

There are four all encompassing components of physical fitness and we need to briefly define each and clarify its role .

Strength is the capacity of a muscle to exert a force against resistance. Strength contributes to power and speed and is of great importance to a majority of sports people.

Muscular Endurance is the capacity to exert a force repeatedly over a period of time, e.g. it is the capacity of your legs to carry you 10 Km without stopping.

Flexibility is the range of motion about a joint. Improving flexibility involves the stretching of muscles and tendons to maintain or increase suppleness, and provides increased resistance to muscle injury or soreness.

Cardio-Respiratory Endurance is the most essential component of physical fitness. It is the efficient functioning of the heart and lungs.

Aerobic Fitness

The largest amount of oxygen that you can use per minute during exercise is called your maximum oxygen uptake (MVo2). This is often referred to as your aerobic capacity.

The effort that you can exert over a prolonged period of time is limited by your ability to deliver oxygen to the working muscles. Regular vigorous exercise produces a training effect that can increase your aerobic capacity by as much as 20 to 30%. An increased MVO2 indicates an increased ability of the heart to pump blood, of the lungs to ventilate oxygen and of the muscles to take up oxygen.

Anaerobic Training

This means “without oxygen” and is the output of energy when the oxygen supply is insufficient to meet the body’s long term energy demands. (For example, 100 meter sprint).

The Training Threshold

This is the minimum level of exercise which is required to produce significant improvements in any physical fitness parameter.

Progression

As your become fitter, a higher intensity of exercise is required to create an overload and therefore provide continued improvement

Overload

This is where you exercise at a level above that which can be carried out comfortably. The intensity, duration and frequency of exercise should be above the training threshold and should be gradually increased as the body adapts to the increasing demands. As your fitness level improves, the training threshold should be raised. Working through your program and gradually increasing the overload factor is important.

30 ©2012

Specificity

Different forms of exercise produce different results. The type of exercise that is carried out is specific both to the muscle groups being used and to the energy source involved.

There is little transfer of the effects of exercise, i.e. from strength training to cardiovascular fitness.

That is why it is important to have an exercise program tailored to your specific needs.

Reversibility

If you stop exercising or do not do your program often enough, you will lose the benefits you have gained. Regular workouts are the key to success.

Warm Up

Every exercise program should start with a warm up where the body is prepared for the effort to come. It should be gentle and preferably use the muscles to be involved later.

Stretching should be included in both your warm up and cool down , and should be performed after 3-

5 minutes of low intensity aerobic activity or callisthenic type exercise.

Warm Down or Cool Down

This involves a gradual decrease in the intensity of the exercise session. Following exercise, a large supply of blood remains in the working muscles. If it is not returned promptly to the central circulation, pooling of blood may occur in the muscles.

Heart Rate

As you exercise, the rate at which your heart beat increases. This is often used as a measure of the required intensity of exercise. You need to exercise hard enough to condition your circulatory system, and increase your pulse rate, but not enough to strain your heart.

Your initial level of fitness is important in developing an exercise program for you. If you are starting off, you can get a good training effect with a heart rate of 110-120 beats per minute(BPM). If you are fitter, you will need a higher threshold of stimulation.

To begin with, you should exercise at a level that elevates your heart rate to about 65 to 70% of your maximum. If you find this is too easy, you may want to increase it, but it is better to lean on the conservative side.

As a rule of thumb, the maximum heart rate is 220 minus your age. As you increase in age, your heart, like other muscles, loses some of its efficiency. Some of its natural loss is won back as fitness improves.

The following table is a guide to those who are “starting fitness”.

Age 25 30 35 40 45 50 55 60 65

Target heart Rate

Count 23 22 22 21 20 19 19 18 18

Beats 138 132 132 126 120 114 114 108 108

Pulse Count

The pulse count(on your wrist or carotid artery in the neck, taken with two index fingers)is done for ten seconds, taken a few seconds after you stop exercising. This is for two reasons: (a) 10 seconds is long enough for accuracy, (b) the pulse count is to approximate your BPM rate at the time you are exercising. Since heart rate slows as you recover, a longer count isn’t as accurate.

The target is not a magic number, but a general guide. If you’re above average fitness, you may work quite comfortably a little above that suggested for your age group.

31 ©2012

The following table is a guide to those who are keeping fit. Here we are working at about 80% of maximum.

25 30 35 40 45 50 55 60 65

Target heart Rate

10

Beats 156 156 150 144 138 132 132 126 120

Don’t push yourself too hard to reach the figures on this table. It can be very uncomfortable if you overdo it. Let it happen naturally as you work through your program. Remember, the target is a guide, not a rule, a little above or below is just fine.

Two final comments:(1) don’t be concerned with day to day variations in your pulse rate, being under pressure or not enough sleep can affect it;(2) your pulse rate is a guide, don’t become a slave to it.

Muscle Soreness

For the first week or so, this may be the only indication you have that you are on an exercise program.

This, of course, does depend on your overall fitness level. A confirmation that you are on the correct program is a very slight soreness in most major muscle groups. This is quite normal and will disappear in a matter of days.

If you experience major discomfort, you may be on a program that is too advanced or you have increased your program too rapidly.

If you experience PAIN during or after exercise, your body is telling your something.

Stop exercising and consult your doctor.

What to Wear

Wear clothing that will not restrict your movement in any way while exercising. Clothes should be light enough to allow the body to cool. Excessive clothing that causes you to perspire more than you normally would while exercising, gives you no advantage. The extra weight you lose is body fluid and will be replaced with the next glass of water you drink. It is advisable to wear a pair of gym or running shoes or “sneakers”.

Breathing during Exercise

Do not hold your breath while exercising. Breathe normally as much as possible. Remember, breathing involves the intake and distribution of oxygen, which feeds the working muscles.

Rest periods

Once you start your exercise program, you should continue through to the end. Do not break off halfway through and then restart at the same place later on without going through the warm-up stage again.

The rest period required between strength training exercises may vary from person to person. This will depend mostly on your level of fitness and the program you have chosen. Rest between exercises by all means, but do not allow this to exceed two minutes. Most people manage with half minute to one minute rest periods

Stretching

Stretching should be included in both your warm up and cool down, and should be performed after 3-5 minutes of low intensity aerobic activity or callisthenic type exercise. Movements should be performed slowly and smoothly, with no bouncing or jerking. Move into the stretch until slight tension, not pain, is felt in the muscle and hold for 20-30 seconds. Breathing should be slow, rhythmical and under control, making sure never to hold your breath.

32 ©2012

33 ©2012

34 ©2012

WARRANTY

MANUFACTURER LIMITED WARRANTY, REPAIR AND SERVICE

WHAT DOES THIS WARRANTY COVER?

This warranty covers your Free Spirit Treadmill against defects in material and workmanship when used for the purpose intended, under normal conditions and provided it receives proper care.

HOW LONG DOES THE COVERAGE LAST ? This warranty lasts for one year on all parts and labour, 10 years on motor only and lifetime on the frame from date of purchase. This warranty is not transferable and is extended only to the original owner.

WHAT WILL SEARS DO?

Sears will provide a replacement part at no charge for any part found defective in workmanship or materials during the warranty period.

WHAT DOES THIS WARRANTY NOT COVER?

This warranty does not cover fitness products which are (1) used for commercial or other income producing purposes, or (2) subject to misuse, neglect, accident or unauthorized repairs and alterations. Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

HOW DO YOU GET SERVICE?

In order to obtain service as provided by this warranty, contact your nearest Sears Canada Inc. service center.

SEARS TEN

YEAR

MOTOR WARRANTY

WHAT DOES THIS WARRANTY COVER?

This warranty covers your treadmill motor against defects in material and workmanship when used for the purpose intended, under normal conditions and provided it receives proper care.

HOW LONG DOES THE COVERAGE LAST?

This warranty lasts for ten years from date of purchase. This warranty is not transferable and is extended only to the original owner.

WHAT YOU NEED TO DO? You need to record the date of purchase in the area provided below. You must keep your receipt which shows the date of purchase of your treadmill. We suggest you staple it to this page.

WHAT WILL SEARS DO?

Sears provide a replacement part at no charge for any part found defective in workmanship or materials during the warranty period.

WHAT DOES THIS WARRANTY NOT COVER? This warranty does not cover fitness products which are (1) used for commercial or other income producing purposes, or (2) subject to misuse, neglect, accident or unauthorized repairs and alterations. Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

HOW DO YOU GET SERVICE

? In order to obtain replacement parts as provided by this warranty, contact your nearest Sears Canada Inc. store, service center or the manufacturer at 1-888-

707-1880.

35 ©2012

OWNER`S

MANUAL

Model No.

C249 30120

FREE SPIRIT

TREADMILL

SERVICE

Is at

YOUR

SERVICE

Serial

No.

Model and serial number may be found on the serial number label on the front of the treadmill.

You should record both model number and serial number and keep in a safe place for future reference.

HOW TO ORDER REPLACEMENT PARTS

The MODEL NUMBER for the TREADMILL will be found on the frame

Always mention this MODEL NUMBER when requesting service or replacement parts for your TREADMILL.

All parts listed herein may be ordered through SEARS CANADA INC.RETAIL OR

CATALOG STORES AND SERVICE CENTERS. If the parts you need are not stocked locally your order will be electronically transmitted to a SEARS Parts

Distribution Center for expedited handling.

When ordering parts by mail, selling prices will be furnished on request or parts will be shipped at prevailing prices and you will be billed accordingly.

WHEN ORDERING REPLACEMENT PARTS, ALWAYS GIVE THE

FOLLOWING

INFORMATION.

1.

PART NUMBER

2.

PART DESCRIPTION

3.

MODEL NUMBER

4.

NAME OF ITEM

Your sears merchandise takes on added value when you discover that Sears has Service

Units throughout the Country. Each is staffed by Sears, Trained Technicians Sears approved methods.

For assembly helps or missing parts call the factory at 1-888-707-1880

36 ©2012

Get it fixed, at your home or ours!

Just Call:

1-800-4-MY-HOME

®

(1-800-469-4663)

24 hours a day, 7 days a week

For the repair of major brand appliances in your own home … no matter who made it, no matter who sold it!

For your nearest Sears Parts & Service location, to bring in products like vacuums, lawn equipment and electronics.

For Sears Parts & Service , to order the replacement parts, accessories and owner’s manuals that you need to do-it-yourself.

www.sears.ca

_______________________________________________________________________________________________

To purchase or inquire about a Sears Maintenance Agreement, call:

1-800-361-6665

9 a.m. – 11 p.m. Mon. – Fri. EST, 9 a.m. – 4 p.m. Sat.

_______________________________________________________________________________________________

Pour service en francais:

1-800-LE-FOYER MC

(1-800-533-6937)

www.sears.ca

®/TM

Trademarks of Sears, Roebuck and Co. used under license by Sears Canada

®

Marque deposée/

MC

Marque de commerce de Sears, Roebuck and Co. utilisée en vertu d’une licence de Sears Canada

37 ©2012