advertisement
For service questions, please call Dimplex at 1-888-346-7539.
For sales inquiries, please call Sylvane at 1-800-934-9194 or visit sylvane.com.
Service Manual
26” Self Trimming Fireplace
Model Number:
DF2608
DF2622
NBDF2608
UL Part Number
6904400359
IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to service this
fireplace. For your safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage.
REV PCN DATE
00 11527 Jul 20, 09
Dimplex North America Limited
1367 Industrial Road Cambridge ON Canada N1R 7G8
1-888-346-7539 www.dimplex.com
In keeping with our policy of continuous product development, we reserve the right to make changes without notice.
© 2011 Dimplex North America Limited
01
02
03
11658 Oct 13, 09
11879 Feb 12, 10
Jan 3.12
7400200000R03
Table of Contents
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Exploded Parts Diagram - DF2608/NBDF2608 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Wiring Diagram - DF2608 / NBDF2608 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Exploded Parts Diagram - DF2622 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Wiring Diagram - DF2622 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Front Glass Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Partially Reflective Glass Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3-Position Switch Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Heater Switch Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Light Dimmer Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Flame Speed Control Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Flicker Motor/Flicker Rod Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Thermostat Control Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Remote Control Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Log Driver Controller Replacement (DF2608 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Lower Light Harness Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Heater Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Power Cord Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Always use a qualified technician or service agency to repair this fireplace.
!
NOTE: Procedures and techniques that are considered important enough to emphasize.
CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the
equipment.
WARNINg: Procedures and techniques which, if not carefully followed, will expose the user to the
risk of fire, serious injury, or death.
2
Operation
This section will explain the function of each convenient control (Figure 2).
To access the controls, flip open the control panel cover towards the bottom of the fireplace (Figure 1).
Figure 1
when first used. This odor is a normal condition caused by initial heating of internal heater parts and will not occur again.
Resetting The Temperature Cutoff Switch
This unit is equipped with a thermostat which controls the temperature of the room. It does this by turning the heater on and off. The heater is protected with a safety device to prevent overheating. Should the heater overheat, an automatic cut out will turn the heater off and it will not come back on without being reset. It can be reset by switching the 3-Position Switch to Off (“ o ”)and waiting five (5) minutes before switching the unit back on.
CAUTION: If you need to continuously reset the heater, unplug the unit and call Technical Support at
1-888-346-7539. Please have your model and serial number ready when calling.
Figure 2
A B C E D
Remote Control
The fireplace is supplied with an integrated on/off remote control.
! NOTE: Ensure that the 3-Position
Switch on the fireplace is set to the remote control setting (“II” position).
To operate, push the ON button to turn the fireplace on, push the OFF button to turn the fireplace off.
Figure 3
OFF
Button
A. 3-Position Switch
The switch has two (2) On positions marked with “ I ” and
“ II ”. The “ I ” position is for manual operation. In this position the built-in remote control is bypassed. The “ II ” position is for operating the unit with the provided remote control. When in “ II ” position the unit is operated with the ON and OFF buttons of the remote control. When the switch is in the center “ o ” position the unit is off.
B. Flame Speed Control
Turn the Flame Speed Control knob to adjust the flame speed to the desired level.
C. Light Dimmer Control
Turn the Light Dimmer Control knob to increase or decrease the brightness of the interior of the fireplace.
D. Heater Switch
The Heater Switch supplies power to the heating unit when the 3-Position Switch (A) is on ( “ I ” or “ II ” positions) .
E. Thermostat Control
To adjust the temperature to your individual requirements, turn the thermostat control clockwise all the way to turn on the heater. When the room reaches the desired temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in this position to maintain the room temperature at its setting. For additional heat, turn clockwise until you hear the click again and the heater will turn on. To turn the heater off, rotate the knob fully counter clockwise.
! NOTE: The heater may emit a slight, harmless odor
Battery Replacement (Figure 3)
To replace the battery:
• Slide battery cover open on the hand held transmitter.
• Correctly install one (1) 12 Volt
(A23) battery in the battery holder.
• Close the battery cover.
ON
Button
Battery
Cover
Remote Initialization/Reprogram
Follow these steps for remote control initialization and if required, reinitialization:
1. Disconnect power to fireplace.
2. Set the 3-Position Switch to the Remote position (Figure
2A).
3. Wait a minimum of five (5) seconds and then reacquire power to fireplace.
4. Within 10 seconds of reacquiring power, press the ON button located on the remote control.
! NOTE: You will have only 10 seconds to perform this last step. Failure to do so will result in these steps needing to be followed again.
3
Maintenance
WARNINg: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons.
Figure 5
Light Block
Light Block screws (4)
Light Bulb Replacement
Allow at least five (5) minutes for the light bulbs to cool before touching them to avoid accidental burning of the skin.
The light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and detail of the log ember bed exterior reduces. There are three (3) bulbs under the Log Set Assembly, which generate the flames and embers, and two (2) bulbs above that illuminate the log exterior.
Lower Light Bulb Requirements: Quantity of three (3) clear chandelier or candelabra bulbs with an E-12 (small) socket base, 60 Watt rating. Example: GE 60BC or Philips 60CTC.
Do not exceed 60 Watts per bulb.
Helpful Hints: It is a good idea to replace all light bulbs at one time if they are close to the end of their rated life. Group replacement will reduce the number of times you need to open the unit to replace light bulbs. Care must be taken when removing the Log set assembly as it contains LED’s and wires (DF2608 only).
1.
2.
3.
4.
5.
6.
Slide fireplace out of mantel.
Lay unit on it’s back for safe removal of front glass.
Remove three (3) Phillips screws from the right side of trim.
Remove trim.
Slide glass to right side of fireplace to remove (Figure 3).
Pull the front edge of the plastic ember bed or plastic grate up and forward until the rear tab releases from the ledge located at the bottom of the partially reflective glass (Figure 4).
! IMPORTANT: Only handle the log set assembly by the ember bed or plastic grate.
! NOTE: Log set assembly fits tightly into firebox, some force may be necessary to remove.
7.
8.
9.
10.
Set log set assembly in front of fireplace.
Remove flicker rod by pulling rod to the right, towards the flicker motor. Bend the flicker rod enough to clear the bracket on the left, lift out and pull flicker rod off of flicker motor shaft (Figure 5).
Remove four (4) Phillips screws (two (2) per side) which attach light filter bracket for easier access to light bulbs
(Figure 5).
Unscrew bulbs counter clockwise to remove.
Figure 3
Log Set
Assembly
Front
Glass
Trim
Flicker Rod
Light Filter
Bracket screws (2)
Lower Light
Bulbs (3)
Figure 4
Back
Ledge
Rear
Tab
Log
Ember Bed
Side Section
11.
12.
13.
Insert new bulbs and screw in clockwise.
Replace light filter bracket and flicker rod.
Install the log set assembly by placing the front, bottom edge of the ember bed in the track behind the control panel. Once in place, push down on the back edge of the ember bed until the rear tab snaps into place under the mirror (Figure 4).
! NOTE: Ensure the log set Assembly is installed tightly under the bottom edge of the mirror to prevent light leakage.
14. Lay unit on it’s back and slide Front Glass back into position and attach trim.
Upper Light Bulb Requirements: Quantity of two (2) clear chandelier or candelabra bulbs with an E-12 (small) socket base, 15 Watt rating.
Do not exceed 25 Watts per bulb.
To access the upper light bulb area:
1.
2.
3.
4.
5.
6.
Slide fireplace out of mantel.
Lay unit on it’s back for safe removal of front glass.
Remove three (3) Phillips screws from right side of trim.
Remove trim.
Slide glass to the right side of the fireplace to remove
(Figure 3).
Upper bulbs are located in the upper left and upper right corners of fireplace, behind the light block bracket
(Figure 5).
7.
8.
9.
10.
11.
Remove the four (4) Phillips screws that attach the light block to the firebox (Figure 5).
Unscrew bulbs counter clockwise.
Insert new bulbs and screw in clockwise.
Re-attach light block bracket.
Lay unit on it’s back, slide front glass back into position and attach Trim.
Front
Edge
glass Cleaning
The glass is cleaned in the factory during the assembly operation. During shipment, installation, handling, etc., the clear door may collect dust particles, these can be removed by dusting lightly with a clean dry cloth.
To remove fingerprints or other marks, the clear door can be cleaned with a damp cloth.
Fireplace Surface Cleaning
Use a cloth dampened with warm water only to clean painted surfaces of the electric fireplace. Do not use abrasive cleaners.
4
Exploded Parts Diagram - DF2608/NBDF2608
4
10
12
16
13
7
18
1
14
1
15
9
19
8
11
5
6
1.
2.
3.
4.
Replacement Parts List
Part Number
Replacement Part:
6904400359
Log Set . . . . . . . . . . . . . . . . . . . . . . . . 0439560100RP
Log Driver Controller . . . . . . . . . . . . . . 3000390100RP
Flicker Motor . . . . . . . . . . . . . . . . . . . 3000240200KIT
Heater Assembly (with cutout) . . . . . . 2000330100RP
5.
6.
7.
8.
9.
Thermostat . . . . . . . . . . . . . . . . . . . . . 2300150100RP*
Heater Switch . . . . . . . . . . . . . . . . . . . 2800210500RP
3-Position Switch . . . . . . . . . . . . . . . . 2800210100RP
Flame Speed Control
Light Dimmer Control
. . . . . . . . . . . . . 3000240500RP
. . . . . . . . . . . . . 3000250100RP
10. Power Cord . . . . . . . . . . . . . . . . . . . . 4100040200RP
11.
12.
Single Light Holder . . . . . . . . . . . . . . . 2500150300RP
Double Light Harness . . . . . . . . . . . . 2500400300RP
13. Partially Reflective Glass . . . . . . . . . . 5901210200RP
Partially Reflective Glass (NBDF2608) 5901450100RP
14.
15.
Front Glass . . . . . . . . . . . . . . . . . . . . 5901220100RP
Control Knob (3 on unit) . . . . . . . . . . . 8800000200RP
16.
17.
18.
19.
Remote Control . . . . . . . . . . . . . . . . . 3000370500RP
Remote Control Receiver
Terminal Block . . . . . . . . . . . . . . . . . . 4000070100RP
Flicker Rod
. . . . . . . . . . 3000380200RP
. . . . . . . . . . . . . . . . . . . . . 5901250100RP
5
3
2
17
Wiring Diagram - DF2608 / NBDF2608
Remote Control
Receiver
Heater
Switch
3-Position
Switch
Log Set
Driver
Thermostat
Heater
Assembly
Power
Cord
Light Dimmer
Control
Flame Speed
Control
6
Exploded Parts Diagram - DF2622
9
3
11
22
6
17
13
1
20
14
12
21
8
18
7
15
10
Replacement Parts List
4.
5.
6.
7.
Part Number 6904400659
Replacement Part:
1. Log Set . . . . . . . . . . . . . . . . . . . . . . . 0439560200RP
2.
3.
Flicker Motor . . . . . . . . . . . . . . . . . . 3000240200KIT
Heater Assembly (with cutout) . . . . . 2000330100RP
Thermostat . . . . . . . . . . . . . . . . . . . . 2300150100RP*
Heater Switch . . . . . . . . . . . . . . . . . . 2800210100RP
3-Position Switch . . . . . . . . . . . . . . . 2800210500RP
Flame Speed Control . . . . . . . . . . . . 3000240500RP
8.
9.
10.
11.
Light Dimmer Control . . . . . . . . . . . . 3000250100RP
Power Cord . . . . . . . . . . . . . . . . . . . 4100040200RP
Single Light Holder . . . . . . . . . . . . . . 2500150300RP
Double Light Harness . . . . . . . . . . . 2500400300RP
12. Partially Reflective Glass . . . . . . . . . 5901450100RP
19
5
4
13.
14.
Front Glass . . . . . . . . . . . . . . . . . . . 5901220100RP
Control Knob (3 on unit) . . . . . . . . . . 8800000200RP
15.
16.
17.
Remote Control
Remote Control Receiver . . . . . . . . . 3000380200RP
Terminal Block
. . . . . . . . . . . . . . . . 3000370500RP
. . . . . . . . . . . . . . . . . 4000070100RP
18. Flicker Rod . . . . . . . . . . . . . . . . . . . . 5901250100RP
Stainless Steel Replacement Parts for DF2622SS
19. Stainless Steel Control Cover . . . . . . 1018760180RP
20. Stainless Steel Top Trim . . . . . . . . . . 1018830180RP
21.
22.
Stainless Steel Right Side Trim
Stainless Steel Left Side Trim
. . . . . 1018840180RP
. . . . . . 1018830280RP
7
2
16
Wiring Diagram - DF2622
3-Position
Switch
Remote Control
Receiver
Light Dimmer
Control
Power Cord
Heater
Switch
Heater
Assembly
Thermostat
8
Front glass Replacement
CAUTION: If unit was operating prior to servicing allow at least 10 minutes for lights, heating elements and top panel to cool off to avoid accidental burning of skin.
3.
4.
5.
WARNINg: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons.
1.
2.
Slide firebox out of mantel.
Lay unit on it’s back for safe removal of Front Glass.
6.
Remove three (3) Phillips screws from right side of Trim.
Remove Trim.
Slide glass to the right side of the firebox to remove
(Figure 6).
Reassemble using replacement Front Glass in reverse order as described above.
CAUTION: Even though the glass is safety glass it may break if bumped, struck or dropped. Care must be taken when handling the glass.
Figure 6
Reflective Glass.
! IMPORTANT: Only handle the Log Set Assembly by the Ember Bed or plastic grate.
! NOTE: Log Set Assembly fits tightly into firebox, some force may be necessary to remove.
7.
8.
Loosen but do not remove the two (2) Philips screws that clamp the Partially Reflective Glass in place, and swivel down so that the clamp clears the edge of the
Partially Reflective Glass (Figure 7).
Push the Partially Reflective Glass out from behind to clear the frame and remove.
9. Insert replacement Partially Reflective Glass top end first and lay the bottom end gently in the bottom track of the frame.
10. Tighten clamps back into place and reassemble firebox in reverse order as described above.
Figure 7
Partially Reflective
Glass
Clamp
Trim
Log Set
Assembly
Front Glass
Partially Reflective Glass Replacement
CAUTION: If unit was operating prior to servicing allow at least 10 minutes for lights, heating elements and top panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons.
1.
2.
Slide firebox out of mantel.
Lay unit on it’s back for safe removal of Front Glass.
3.
4.
5.
Remove three (3) Phillips screws from the right side of
Trim.
Remove Trim.
Slide glass to right side of fireplace to remove (Figure
6).
CAUTION: Even though the glass is safety glass it may break if bumped, struck of dropped. Care must be taken when handling the glass.
6. Pull the front edge of the plastic Ember Bed or plastic grate up and forward until the rear tab releases from the ledge located at the bottom of the Partially
3-Position Switch Replacement
CAUTION: If unit was operating prior to servicing allow at least 10 minutes for lights, heating elements and top panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons.
1. Remove the firebox from the mantel.
2.
3.
4.
Lay unit on its back.
Remove the 12 Philips screws that fasten the bottom cover to the rest of the firebox. There are: two (2) screws on each side; two (2) screws on the back panel
(you may have to tip the bottom of the firebox up if it is laying on its back), four (4) screws in the front directly under the control panel; and two (2) screws on the bottom of the firebox (see Figure 8). The bottom panel is now free to be removed.
Locate the 3-Position Switch mounted on the control panel on the left side (Figure 9) and disconnect the three (3) wiring clips noting their original locations.
CAUTION: Internal wire colors may not be the same within the unit being serviced as those shown. To avoid damage to the unit, damage to property or personal injury, ensure wires are reconnected to match their original locations.
5. Depress the two (2) retainer clips on the top and
9
6. bottom of the switch and push the switch out the front panel.
Properly orient the new switch and reconnect all of the wiring clips and connections as before.
7. Push the switch through the front control panel until the Retainer Clips snap the switch into place, then reassemble the firebox in reverse order as above.
! NOTE: When placing bottom panel back onto unit, position the metal lip from under the control panel between the rubber spacers (attached to the bottom panel) and the sheet metal of the bottom panel.
Heater Switch Replacement
CAUTION: If unit was operating prior to servicing allow at least 10 minutes for lights, heating elements and top panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons.
1.
2.
3.
Remove the firebox from the mantel.
Lay unit on its back.
Remove the 12 Philips screws that fasten the bottom cover to the rest of the firebox. There are: two (2)
Figure 8
Screws To Remove
Figure 9
3-Position Switch
Retainer Clips
(One top, one bottom)
4. screws on each side; two (2) screws on the back panel
(you may have to tip the bottom of the firebox up if it is laying on its back), four (4) screws in the front directly under the control panel; and two (2) screws on the bottom of the firebox (Figure 8). The bottom panel is now free to be removed.
Locate the Heater Switch mounted on the control panel on the right side (Figure 10, page 11) and disconnect the two (2) wiring clips noting their original locations.
CAUTION: Internal wire colors may not be the same within the unit being serviced as those shown. To avoid damage to the unit, damage to property or personal injury, ensure wires are reconnected to match their original locations.
5. Depress the two (2) retainer clips on the top and bottom of the switch and push the switch out the front of the firebox.
6. Properly orient the new switch and reconnect all of the wiring clips and connections as before.
7. Push the switch through the front control panel until the Retainer Clips snap the switch into place, then reassemble the firebox in reverse order as above.
! NOTE: When placing bottom panel back onto unit, position the metal lip from under the control panel between the rubber spacers (attached to the bottom panel) and the sheet metal of the bottom panel.
Light Dimmer Replacement
CAUTION: If unit was operating prior to servicing allow at least 10 minutes for lights, heating elements and top panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons.
1.
2.
Remove the firebox from the mantel.
Lay unit on its back.
3. Remove the 12 Philips screws that fasten the bottom
Figure 10
Heater Switch
Retainer Clips
(One top, one bottom)
Wire 1: Dark orange piggy-back wire from bottom terminal of switch to: top, left terminal of Dimmer Control and; to one of 3 wire connectors.
Wire 2: Black, smooth edged wire from power cord to middle terminal of switch.
Wire 3: Grey wire from top terminal of switch to opposite side of firebox.
Wire 3 Wire 2 Wire 1
Wire 1
Wire 2
Wire 1: Dark orange wire from bottom terminal of switch to top, right terminal of
Log Driver (DF2608).
Wire 2: Yellow wire from top terminal of switch to other side of firebox.
10
4.
5. cover to the rest of the firebox. There are: two (2) screws on each side; two (2) screws on the back panel
(you may have to tip the bottom of the firebox up if it is laying on its back), four (4) screws in the front directly under the control panel; and two (2) screws on the bottom of the firebox (Figure 8). The bottom panel is now free to be removed.
Locate the Light Dimmer Control Board and
Potentiometer mounted on the left side (Figure 11).
Pull off the Light Dimmer Control knob and unscrew the retaining nut (Figure 11). The Potentiometer can now be removed from the panel by pushing the potentiometer through the front panel and removed from inside the firebox.
6. The Light Dimmer Control board is fastened to the underside of the Ember Bed support by four (4) mounting studs, one in each corner (Figure 11).
Squeeze each mounting stud’s clasp to release the circuit board from the firebox.
! NOTE: If mounting studs are damaged, replacement mounting studs will need to be inserted from underneath
Log Set Assembly. Follow steps 1 - 6 of Partially Reflective
Glass Replacement procedure on page 9 to do this. It is recommended to attempt to release the control board without cutting mounting studs.
7.
8.
Properly orient the replacement Light Dimmer Control board and push it onto the four (4) mounting studs
(running the connecting Potentiometer wires under the board) until the clasps of the mounting studs snap the control board into place.
Properly orient the Potentiometer attached to the replacement control board, push it through the front control panel and anchor it in place using the retaining
Figure 11
Retaining
Nut
Potentiometer
Light Dimmer
Control Board
Mounting Studs (4)
Wire 1 Wire 2
Wire 1: White wire from bottom, left terminal of board to cable sheath leading to upper firebox area.
Wire 2: Dark orange piggy-back wire from top, left terminal of board to: top, right terminal of Flame Speed Control board and; bottom terminal of 3-Position Switch.
9. nut removed in step 5.
Disconnect one of the two (2) wire leads from the original control board (which are still connected to parts within the firebox) and immediately connect it to the new control board’s terminal, matching its position.
Continue with the remaining wire using the same procedure.
CAUTION: Internal wiring and colors may not be the same within the unit being serviced as those shown. To avoid damage to the unit, damage to property or personal injury, ensure wires are reconnected to match their original locations.
10. Follow steps 1 through 3 in reverse order to reassemble the firebox.
! NOTE: When placing bottom panel back onto unit, position the metal lip from under the control panel between the rubber spacers (attached to the bottom panel) and the sheet metal of the bottom panel.
Flame Speed Control Replacement
CAUTION: If unit was operating prior to servicing allow at least 10 minutes for lights, heating elements and top panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons.
1.
2.
3.
4.
Remove the firebox from the mantel.
Lay unit on its back.
Remove the 12 Philips screws that fasten the bottom cover to the rest of the firebox. There are: two (2) screws on each side; two (2) screws on the back panel
(you may have to tip the bottom of the firebox up if it is laying on its back), four (4) screws in the front directly under the control panel; and two (2) screws on the bottom of the firebox (Figure 8). The bottom panel is now free to be removed.
Locate the Flame Speed Control and Potentiometer mounted on the left hand side (Figure 12).
5.
6. The Flame Speed Control board is fastened to the underside of the Ember Bed support by four (4) mounting studs, one in each corner (Figure 12).
Squeeze each mounting stud’s clasp to release the circuit board from the firebox.
! NOTE: If mounting studs are damaged, replacement mounting studs will need to be inserted from underneath
Log Set Assembly. Follow steps 1 - 6 of Partially
Reflective Glass Replacement procedure to do this. It is recommended to attempt to release the control board without cutting mounting studs.
7.
Pull off the Flame Speed Control knob and unscrew the retaining nut (Figure 12). The Potentiometer can now be removed from the panel by pushing the
Potentiometer through the front panel and remove from inside the firebox.
Properly orient the replacement Flame Speed Control board and push it onto the four (4) mounting studs
(running the connecting Potentiometer wires under the
11
Figure 12
Potentiometer
Flame Speed
Control Board
Retaining
Nut
Wire 1
Mounting Studs (4)
Wire 3
Wire 2
Cable connector for Flicker Motor
Wire 1: Dark orange piggy-back wire from top, right terminal of Flame Speed Control board to: top, right terminal of Light Dimmer board and; other side of firebox.
Wire 2: Blue wire from bottom, right terminal of Flame
Speed Control board to one of 3 wire connectors.
Wire 3: Black wire from bottom, right terminal of Flame
Speed Control board to power cord.
board where possible) until the clasps of the mounting studs snap the control board into place.
8.
9.
Properly orient the Potentiometer attached to the replacement control board, push it through the front control panel and anchor it in place using the retaining nut removed in step 5.
Disconnect one of the wire leads from the original control board (which are still connected to parts within the firebox) and immediately connect it to the new control board’s terminal, matching its position.
Continue with the remaining wires (there are four (4) wires which are piggy-backed together in pairs, and the cable connector which leads to the Flicker Motor) using the same procedure.
CAUTION: Internal wiring and colors may not be the same within the unit being serviced as those shown. To avoid damage to the unit, damage to property or personal injury, ensure wires are reconnected to match their original locations.
10. Follow steps 1 through 3 in reverse order to reassemble the firebox.
! NOTE: When placing bottom panel back onto unit, position the metal lip from under the control panel between the rubber spacers (attached to the bottom panel) and the sheet metal of the bottom panel.
Flicker Motor/Flicker Rod Replacement
CAUTION: If unit was operating prior to servicing allow at least 10 minutes for lights, heating elements and top panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons.
1.
2.
Remove the firebox from the mantel.
Lay unit on its back.
3.
4.
Remove the 12 Philips screws that fasten the bottom cover to the rest of the firebox. There are: two (2) screws on each side; two (2) screws on the back panel
(you may have to tip the bottom of the firebox up if it is laying on its back), four (4) screws in the front directly under the control panel; and two (2) screws on the bottom of the firebox (Figure 8). The bottom panel is now free to be removed.
Locate Flicker Rod and Flicker Motor in the base assembly (Figure 13).
5. Gently pull the Flicker Rod to the right as far as possible into the rubber bushing (Figure 13).
! NOTE: When removing the Flicker Rod, damage may occur if bent excessively. If the Flicker Rod is damaged, replace to insure proper operation.
6.
7.
8.
Cautiously bend the Flicker Rod enough so that the remaining end of the Flicker Rod clears the plastic bushing on the left (Figure 14).
Remove the Flicker Rod by pulling it free from the rubber bushing on the motor shaft (Figure 14).
Before removing the Flicker Motor, cut the Flicker Motor
Figure 13
Figure 14
5 Color
Cable
Flicker
Rod
Flicker
Motor
Mounting
Screw
Rubber
Bushing
Flicker
Motor
Mounting
Screw
12
9. wires (five (5) in total) as close to the Flicker Motor as possible.
Remove the rubber bushing from the motor shaft by applying needle nose pliers to the motor shaft and twist the rubber bushing off of the motor shaft.
10. Remove the two (2) motor mounting screws and remove Flicker Motor from the mounting bracket
(Figure 14).
11.
12.
Discard old Flicker Motor.
Pick up new Flicker Motor and cut wire leads to 3 ½ inch long with wire cutters.
13. Using one of the supplied wire connectors from the
Replacement Part Kit, place one (1) yellow wire from the new Flicker Motor and the yellow wire cut in step 8 into each terminal.
14. Secure the wire connector by crimping the 3M symbol with pliers.
15. Pull on end of wires to ensure a strong connection.
16. Repeat the process for the four (4) remaining wires.
Ensure that all wires are paired by color in each
connector.
! NOTE: In the event that multiple Flicker Motors were already replaced within unit, or if required wiring has been cut too short, it may be necessary to replace Flicker Motor and the attached cable as a whole.
To do so: i) Follow steps 1 through 7 and step 9. ii) Unplug the cable connector from the Flame Speed
Control board on the left side of the firebox (Figure 12, page 12).
iii) Cut all cable ties that bind the Flicker Motor Cable and other wires together (wires and cable run behind the lower bulbs).
iv) Follow steps 10 and 11 to remove defective Flicker
Motor.
v) Follow steps 17 through 19 to install new Flicker
Motor.
vi) Run Flicker Motor Cable along channel behind lower bulbs and bind together with other wires using cable ties.
vii) Plug cable connector into Flame Speed Control board (Figure 12).
viii) Reassemble firebox and replace in mantel.
17. Properly orient and secure the replacement Flicker
Motor to the bracket with screws removed in step 10.
18. Replace rubber bushing on motor shaft.
19. Replace Flicker Rod.
20. Reassemble firebox and replace in mantel.
! NOTE: When placing bottom panel back onto unit, position the metal lip from under the control panel between the rubber spacers (attached to the bottom panel) and the sheet metal of the bottom panel.
Thermostat Control Replacement
CAUTION: If unit was operating prior to servicing allow
13 at least 10 minutes for lights, heating elements and top panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons.
1. Remove the firebox from the mantel.
2.
3.
4.
Lay unit on its back.
Remove the 12 Philips screws that fasten the bottom cover to the rest of the firebox. There are: two (2) screws on each side; two (2) screws on the back panel
(you may have to tip the bottom of the firebox up if it is laying on its back), four (4) screws in the front directly under the control panel; and two (2) screws on the bottom of the firebox (Figure 8). The bottom panel is now free to be removed.
Locate the Thermostat Control mounted on the control panel on the right hand side (Figure 15) and disconnect the two (2) wiring clips noting their original locations.
CAUTION: Internal wiring and colors may not be the same within the unit being serviced as those shown. To avoid damage to the unit, damage to property or personal injury, ensure wires are reconnected to match their original locations.
5.
6.
Pull off the thermostat control knob to expose the two
(2) Philips mounting screws (Figure 15).
Remove the mounting screws and remove the thermostat controller from inside the control panel.
7. Properly orient the new Thermostat Control and reconnect the wiring connections.
8. Reassemble in the reverse order as above.
! NOTE: When placing bottom panel back onto unit, position the metal lip from under the control panel between the rubber spacers (attached to the bottom panel) and the sheet metal of the bottom panel.
Figure 15
Thermostat
Wire 1
Wire 2
Screw
Wire 1: Blue wire from right terminal of thermostat to top, right terminal of Remote Control Receiver.
Wire 2: Blue wire from left terminal of thermostat to opposite side of firebox and up to Heater Assembly.
Remote Control Replacement
Remote Control require no replacement procedure however, a reinitialization procedure may need to be followed. Refer to Page 1 for the Remote Initialization/
Reprogram procedure.
CAUTION: If unit was operating prior to servicing allow at least 10 minutes for lights, heating elements and top panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons.
1. Remove the firebox from the mantel.
2.
3.
4.
5.
Lay unit on its back.
Remove the 12 Philips screws that fasten the bottom cover to the rest of the firebox. There are: two (2) screws on each side; two (2) screws on the back panel
(you may have to tip the bottom of the firebox up if it is laying on its back), four (4) screws in the front directly under the control panel; and two (2) screws on the bottom of the firebox (Figure 8). The bottom panel is now free to be removed.
Locate the Remote Control Receiver mounted on the right hand side (Figure 16).
The Remote Control Receiver is fastened to the underside of the Ember Bed support by four (4) mounting studs, one in each corner (Figure 15).
Figure 16
Mounting
Studs (4)
Remote
Control
Receiver
•
•
•
Blue piggy-back:
From top, right terminal of Remote
Control Receiver to 1) right terminal of thermostat and 1) to left terminal of Log Driver board.
Orange piggy-back:
From top, left terminal of Remote
Control Receiver to 1) right terminal of Log Driver board and 1) to opposite side of firebox and to top terminal of
Flame Speed Control board.
grey:
From left side terminal of Remote Control
Receiver to opposite side of firebox, leading to Heater
Assembly.
Squeeze each mounting stud’s clasp to release the circuit board from the firebox.
! NOTE: If mounting studs are damaged, replacement mounting studs will need to be inserted from underneath the Log Set Assembly. Follow steps 1 - 6 of Partially
Reflective Glass Replacement procedure on page 9 to do this. It is recommended to attempt to release the control board without cutting mounting studs.
6. Properly orient the replacement Remote Control
Receiver board and push it onto the four (4) mounting studs until the clasps of the mounting studs snap the control board into place.
7. Disconnect one of the wire leads from the original control board (which are still connected to parts within the firebox) and immediately connect it to the new control board’s terminal, matching its position.
Continue with the remaining wires (there are four (4) wires which are piggy-backed together in pairs, and a single grey wire) using the same procedure.
CAUTION: Internal wiring and colors may not be the same within the unit being serviced as those shown. To avoid damage to the unit, damage to property or personal injury, ensure wires are reconnected to match their original locations.
8. Follow steps 1 through 3 in reverse order to reassemble the firebox.
! NOTE: When placing bottom panel back onto unit, position the metal lip from under the control panel between the rubber spacers (attached to the bottom panel) and the sheet metal of the bottom panel.
Log Driver Controller Replacement
(DF2608 only)
CAUTION: If unit was operating prior to servicing allow at least 10 minutes for lights, heating elements and top panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons.
1.
2.
Remove the firebox from the mantel.
Lay unit on its back.
3. Remove the 12 Philips screws that fasten the bottom cover to the rest of the firebox. There are: two (2) screws on each side; two (2) screws on the back panel
(you may have to tip the bottom of the firebox up if it is laying on its back), four (4) screws in the front directly under the control panel; and two (2) screws on the bottom of the firebox (Figure 8). The bottom panel is now free to be removed.
4. The Log Driver Control Board is fastened to the underside of the Ember Bed support by four (4) mounting studs, one in each corner (Figure 17).
Squeeze each mounting stud’s clasp to release the circuit board from the firebox.
! NOTE: If mounting studs are damaged, replacement mounting studs will need to be inserted from underneath the Log Set Assembly. Follow steps 1 - 6 of Partially
14
Reflective Glass Replacement procedure on page 9 to do this. It is recommended to attempt to release the control board without cutting mounting studs.
5. Properly orient the replacement Log Driver board and push it onto the four (4) mounting studs until the clasps of the mounting studs snap the control board into place.
6. Disconnect one of the wire leads from the original control board (which are still connected to parts within the firebox) and immediately connect it to the new control board’s terminal, matching its position.
Continue with the remaining wires (there are four (4) wires which are piggy-backed together in pairs, and a single grey wire) using the same procedure.
CAUTION: Internal wiring and colors may not be the same within the unit being serviced as those shown. To avoid damage to the unit, damage to property or personal injury, ensure wires are reconnected to match their original locations.
7. Follow steps 1 through 3 in reverse order to reassemble the firebox.
! NOTE: When placing bottom panel back onto unit, position the metal lip from under the control panel between the rubber spacers (attached to the bottom panel) and the sheet metal of the bottom panel.
Lower Light Harness Replacement
CAUTION: If unit was operating prior to servicing allow at least 10 minutes for lights, heating elements and top panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons.
Figure 17
Log Driver
Control
Board
Mounting
Studs (4)
Multicolored LED
Wire Harness
•
•
Blue piggy-back:
From left terminal of Log Driver board to 1) right terminal of Remote Receiver board and 1) to other side of firebox and connecting to wire nut.
Orange piggy-back:
From right terminal of Log Driver board to 1) bottom terminal of Heat Switch and 1) left terminal of Remote Receiver board.
1.
2.
3.
4.
5.
6.
7.
Remove the firebox from the mantel.
Lay unit on its back.
Remove the 12 Philips screws that fasten the bottom cover to the rest of the firebox. There are: two (2) screws on each side; two (2) screws on the back panel
(you may have to tip the bottom of the firebox up if it is laying on its back), four (4) screws in the front directly under the control panel; and two (2) screws on the bottom of the firebox (Figure 8). The bottom panel is now free to be removed.
Locate the three (3) light sockets, in the middle of the firebox.
Remove the lightbulbs and place in a safe location.
Trace the light socket wires by cutting the tie wraps and removing the wire covering. Disconnect the wire connectors that are attached to the sockets that are being replaced, noting the associated connection for each wire.
Remove the retaining ring from the light sockets and replace sockets with new sockets.
8. Replace associated wire connectors.
9. Follow steps 1 through 6 in reverse order to reassemble the firebox.
! NOTE: When placing bottom panel back onto unit, position the metal lip from under the control panel between the rubber spacers (attached to the bottom panel) and the sheet metal of the bottom panel.
Heater Assembly Replacement
CAUTION: If unit was operating prior to servicing allow at least 10 minutes for lights, heating elements and top panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons.
1.
2.
3.
4.
5.
6.
7.
Remove the firebox from the mantel.
Remove the 10 Philips screws that fasten the top cover to the rest of the firebox. There are: (four) 4 screws at the back of the firebox, along the top; two (2) screws on each side and at the top of the firebox; and two (2) screws on the top of the firebox (Figure 18).
Flip the top panel over and place upside down on the top of the unit. You may experience some resistance as the Heater Assembly is mounted to the top panel and may be a snug fit inside the firebox. Orient yourself with the placement of the Heater Assembly and wiring as shown in Figure 19.
Turn the top panel over and, while supporting the
Heater Assembly and panel in one hand, remove the five (5) Phillips heater mounting screws, noting the center screw is of a larger diameter (Figure 20).
Separate the Heater Assembly from the top panel.
Properly orient the new Heater Assembly and attach it to the top panel using the screws removed in step 5.
Disconnect one of the wire leads from the original
Heater Assembly (which are still connected to parts
15
Figure 18
Screws to Remove
Figure 19
Terminal Block
Wire 1
Wire 2
Heater
Assembly
Heating
Element
Figure 21
3-Position
Switch
Power Cord
Flame Speed
Control
Wire Clamp
Wires leading to bottom assembly Wire 3
Wire 4
Wire 5
•
•
•
•
•
Wire 1:
Blue wire connecting top and bottom terminal of
Heater Element on left side.
Wire 2:
Blue wire from top, left terminal of Heater
Element through to lower part of firebox.
Wire 3:
Blue wire connecting inside terminal of Motor to
Terminal Block, matched with blue wire from Terminal
Block to lower part of firebox.
Wire 4:
Black wire from outside terminal of Motor to bottom terminal of Heater Element on right side.
Wire 5:
Yellow wire from top terminal of Heater Element on right side to Terminal Block, matched to yellow wire leading to lower part of firebox.
Figure 20
within the firebox) and immediately connect it to the new Heater Assembly’s terminal, matching its position.
Continue with the remaining wires using the same procedure.
CAUTION: Internal wiring and colors may not be the same within the unit being serviced as those shown. To avoid damage to the unit, damage to property or personal injury, ensure wires are reconnected to match their original locations.
8. Fit Heater Assembly into top of firebox and re-assemble firebox using screws removed in step 2.
Power Cord Replacement
CAUTION: If unit was operating prior to servicing allow at least 10 minutes for lights, heating elements and top panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons.
1. Remove the firebox from the mantel.
2.
3.
4.
5.
Lay unit on its back.
Remove the 12 Philips screws that fasten the bottom cover to the rest of the firebox. There are: two (2) screws on each side; two (2) screws on the back panel
(you may have to tip the bottom of the firebox up if it is laying on its back), four (4) screws in the front directly under the control panel; and two (2) screws on the bottom of the firebox (Figure 8). The bottom panel is now free to be removed.
Locate and disconnect the two (2) power cord wire connections. The smooth edged wire leading from the narrow blade of the power plug connects to the middle of the three (3) terminals on the 3-Position Switch; the side of the power cord leading from the wide blade of the plug, and has ridges along its edge leads to the bottom, right terminal of the Flame Speed Control board (Figure 21).
Using pliers, squeeze the sides of the plastic wire clamp on the Power Cord from inside the chassis and push it through the sheet metal.
6.
7.
8.
9.
Release clamp from the Power Cord and remove
Power Cord from the firebox.
Run replacement Power Cord through the firebox as above and connect wire ends as described in step 4.
Leave two (2) inches of slack in cord and secure in place with clamp.
Follow steps 1 through 3 in reverse order to reassemble the firebox.
16
Troubleshooting guide
general
Circuit breaker trips or fuse blows when unit is turned on
Unit turns on or off by itself
Lights dim in room while the unit is on
PROBLEM
Power cord gets warm
Fireplace seems dark side sources.
rating
CAUSE
Short in unit wiring.
Improper circuit current rating
Remote Control has a similar frequency to other remotes in the area.
Radio frequency disturbance from out-
Defective Remote Control Receiver
Unit is drawing close to circuit current
Normal Operation
Defective Power Cord
Improper operation
Defective Light Dimmer
SOLUTION
Trace wiring in unit.
Additional appliances may exceed the current rating of the circuit breaker or fuse. Plug unit into another outlet or install unit on a dedicated 15 amp circuit.
Replace Remote Control. Initialize to Remote Control
Receiver.
Replace Remote Control. Initialize Remote Control and Receiver.
Replace Remote Control Receiver. Initialize Remote
Control and Receiver.
Move the unit to another outlet or install unit on a dedicated 15 amp circuit
The power cord may get slightly warm to the touch when the heater is on
Replace Power Cord if cord gets hot to the touch.
Refer to Operation Section
Replace Light Dimmer Components
Appearance
Fireplace does not turn on Manually
Fireplace does not turn on using the Remote Control
Improper operation
No incoming power from the electrical wall socket
Refer to Operation Section
Check fuse/breaker panel
Defective 3-Position Switch
Improper operation
Replace 3-Position Switch
Refer to Operation Section
Remote Control not initialized to fireplace Initialize the Remote Control
Remote Control not working Install new battery into the Remote Control. Initialize
Remote Control.
Replace Remote Control Receiver or Remote Control, where necessary. Initialize Remote Control and
Remote Control Receiver.
Flame Frozen
Flame not bright or flame not visible
Log set dim, not glowing
(DF2608 Only)
Loose wiring
Defective Flicker Motor
Defective Flame Speed Control
Burnt out light bulbs
Loose wiring
Defective Light Harness
Loose wiring
Defective Log Driver Controller
Flame Shutter
Defective Log Set
Defective Flicker Motor
Light leaking around the log set Log set not positioned properly
Check wiring connections
Replace Flicker Motor
Replace Flame Speed Control Components
Replace light bulbs
Check wiring connections
Replace Light Harness
Check wiring connections
Replace Log Driver Controller
Replace Log Set
Replace Flicker Motor
Check log set for proper fit
17
For service questions, please call Dimplex at 1-888-346-7539.
For sales inquiries, please call Sylvane at 1-800-934-9194 or visit sylvane.com.
PROBLEM
Heater
Heater is not turning off
CAUSE SOLUTION
Heater is not turning on
Heater is turning off after a couple of minutes of operation
Heater emits an odor
Heater fan turns on but heater lacks heat
Heating element is glowing red
Improper operation
Defective Heater Switch
Defective Thermostat
Improper operation
Loose wiring
Defective Heater Switch
Defective Thermostat
Refer to Operation Section
Replace Heater Switch
Replace Thermostat
Refer to Operation Section
Trace wiring in unit
Replace Heater Switch
Replace Thermostat
Defective Heater Assembly Replace Heater Assembly
Build up of dirt/dust in Heater Assembly Ensure that exterior intake louvers and firebox cavity are free of dirt/dust.
Defective Heater Assembly Replace Heater Assembly
Normal Operation Normal operation is when the heater emits an odor for a brief period after the heater is initially turned on.
The heater is burning off any dust accumulated during manufacturing or operation.
Replace Heater Assembly Defective Heater Assembly
Improper operation
Loose wiring
Refer to Operation Section
Trace wiring in unit
Defective Thermostat
Defective Heater Assembly
Normal Operation
Defective heater assembly
Replace Thermostat
Replace Heater Assembly
Small glowing sections of the element are considered normal.
If larger glowing sections are causing the heater to trip the thermal cutout, unplug unit, discontinue use and replace Heater Assembly.
Noise
Excessive noise with the heater on
Dirty Heater Assembly
Grinding or excessive noise with the heater off
Defective Heater Assembly
Flicker rod hitting or rubbing against internal components
Defective Flicker motor
Buzzing noise from control panel Defective Flame Speed Controller
Ensure that exterior intake louvers and firebox cavity are free of dirt/dust.
Replace Heater Assembly
Ensure rod is straight and mounted properly in the bracket, spinning freely away from other components.
Replace if necessary.
Replace Flicker motor
Replace Flame Speed Controller
18
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement