advertisement
I N S T A L L A T I O N A N D O P E R A T I O N M A N U A L
GAS RANGE STATIC OVEN
G505
G506
G508
For use in GB, IE & DK
230104-7
MANUFACTURED BY
Moffat Limited
PO Box 10001
Christchurch
New Zealand
Ph: (03)
Fax: (03)
WORLD-WIDE BRANCHES
UNITED KINGDOM
Blue Seal
Unit 67, Gravelly Business Park
Gravelly Park
Birmingham
West Midlands
B24 8TQ
Ph: (121) 327 5575
(121) 327 9711 Fax:
UNITED STATES
Moffat Inc
3765 Champion Blvd
Winston-Salem
North Carolina 27115
Ph:
Fax:
CANADA
(336) 661 0257
(336) 661 9546
Serve Canada
22 Ashwarren Road
Downview
Ontario M3J1Z5
Toll Free:800 263 1455
Ph:
Fax:
(416) 631 0601
(416) 631 0315 [email protected] www.servecanada.com www.moffat.com
NEW ZEALAND
Christchurch
Moffat Limited
PO Box 10-001
Auckland
Moffat Limited
4 Waipuna Road
Mt Wellington 16 Osborne Street
Christchurch Auckland
Ph:
Fax:
(03) 389 1007
(03) 389 1276
Ph: (09) 574 3150
Fax: (09) 574 3159
AUSTRALIA
Victoria
Moffat Pty Limited
740 Springvale Road
Mulgrave, Melbourne
Victoria 3171
Ph:
Fax:
(03) 9518 3888
(03) 9518 3838
Western Australia
Moffat Pty Limited
67 Howe Street
Osbourne Park
WA 6017
Ph:
Fax:
(08) 9202 6820
(08) 9202 6836
New South Wales
Moffat Pty Limited
3/142 James Ruse Drive, Rose Hill
PO Box 913, Smithfield
Sydney, N.S.W. 2142
Ph: (02) 8833 4111
Fax: (02) 8833 4133
Queensland
Moffat Pty Limited
30 Prosperity Place
Geebung, Brisbane
Queensland 4034
Ph: (07) 3630 8600
Fax (07) 3630 8623
The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless qualified previously in writing by the manufacturer.
In line with policy to continually develop and improve its products, Moffat Ltd. reserves the right to change the specifications and design without prior notice.
© Copyright Moffat Ltd. March 2010.
Contents List
Blue Seal Gas Static Oven Range
G505
G506
G508
Gas Range Static Oven - 750 mm wide.
Gas Range Static Oven - 900 mm wide.
Gas Range Static Oven - 1200 mm wide.
Introduction .............................................................................................. 2
Specification .............................................................................................. 3
Model Numbers Covered in this Specification
General
Gas Supply Requirements
Gas Connection
Dimensions ................................................................................................ 5
Installation ................................................................................................ 8
Installation Requirements
Unpacking
Location
Clearances
Assembly
Gas Connection
Commissioning
Operation ................................................................................................. 11
Operation Guide
Description of Controls
Open Burners
Griddle
Lighting the Oven Pilot Burner
Lighting the Oven Main Burner
Turning the Oven to ‘Stand-By’ (Pilot ‘ON’ Only)
Oven ‘Shut Down’
Cleaning and Maintenance ...................................................................... 16
General
After Each Use
Daily Cleaning
Weekly Cleaning
Periodic Maintenance
Fault Finding ............................................................................................ 20
Gas Conversion and Specifications.......................................................... 21
Conversion Procedure
Gas Specifications
Replacement Parts List............................................................................ 29
Introduction
We are confident that you will be delighted with your BLUE SEAL GAS RANGE STATIC OVEN and it will become a most valued appliance in your commercial kitchen.
To ensure you receive the utmost benefit from your new Blue Seal appliance, there are two important things you can do.
Firstly:
Please read the instruction book carefully and follow the directions given. The time taken will be well spent.
Secondly:
If you are unsure of any aspect of the installation, instructions or performance of your appliance, contact your BLUE SEAL dealer promptly. In many cases a phone call could answer your question.
CE Only:
These instructions are only valid if the country code appears on the appliance. If the code does not appear on the appliance, refer to the supplier of this appliance to obtain the technical instructions for adapting the appliance to the conditions for use in that country.
WARNING:
I
MPROPER INSTALLATION
,
ADJUSTMENT
,
ALTERATION
,
SERVICE OR MAINTENANCE CAN CAUSE PROPERTY
DAMAGE
,
INJURY OR DEATH
. R
EAD THE INSTALLATION
,
OPERATING AND MAINTENANCE INSTRUCTIONS
THOROUGHLY BEFORE INSTALLING OR SERVICING THIS APPLIANCE
.
WARNING:
INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE USER SMELLS GAS ARE TO BE POSTED IN A PROMINENT
LOCATION
.
THIS INFORMATION SHALL BE OBTAINED BY CONSULTING THE LOCAL GAS SUPPLIER
.
WARNING:
G
REAT CARE MUST BE TAKEN BY THE OPERATOR TO USE THE EQUIPMENT SAFELY TO GUARD IT AGAINST RISK
OF FIRE
.
•
•
T
HE APPLIANCE MUST
NOT
BE LEFT ON UNATTENDED
.
I
T IS RECOMMENDED THAT A REGULAR INSPECTION IS MADE BY A COMPETENT SERVICEMAN TO ENSURE
•
CORRECT AND SAFE OPERATION OF YOUR APPLIANCE IS MAINTAINED
.
DO NOT
STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS OR LIQUIDS IN THE VICINITY OF
•
THIS OR ANY OTHER APPLIANCE
.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION
.
C
AUTION
:
This appliance is;
•
For professional use and is to be used by qualified persons only.
•
Only authorised service persons are to carry out installation, servicing and gas conversion operations.
•
Components having adjustments protected (e.g. paint sealed) by the manufacturer should not be adjusted by the user / operator.
•
DO NOT operate the appliance without the legs supplied fitted.
2
Specifications
Model Numbers Covered in this Specification
G505D[1]
G505C[1]
G506D[1]
G506C[1]
Gas Static Oven + 4 Open Burners.
Gas Static Oven + 2 Open Burners + 300 mm Griddle.
Gas Static Oven + 6 Open Burners.
Gas Static Oven + 4 Open Burners + 300 mm Griddle.
G506B[1]
G506A
Gas Static Oven + 2 Open Burners + 600 mm Griddle.
Gas Static Oven + 900 mm Griddle.
G508D[1]
G508C[1]
G508B[1]
G508A[1]
Gas Static Oven + 8 Open Burners + Storage Cabinet.
Gas Static Oven + 6 Open Burners + 300 mm Griddle + Storage Cabinet.
Gas Static Oven + 4 Open Burners + 600 mm Griddle + Storage Cabinet.
Gas Static Oven + 2 Open Burners + 900 mm Griddle + Storage Cabinet.
[1] - Open Burner Options;
F - With Flame Failure Protection.
PF - With Pilot and Flame Failure Protection.
General
A heavy duty, general purpose gas range created for compact modular kitchens. It has a high option
Cook Top / Griddle arrangement and is available on industrial adjustable feet or on robust rollers.
Open Burners are available in either 'PF' (Pilot and Flame Failure) or 'F' (Flame Failure Only) options.
Open Burner and Griddle options are fitted with individual flame failure for each open burner.
Griddles are fitted with pilot, flame failure and piezo ignition as standard. Easy clean stainless steel external finish.
The oven is fitted with pilot and flame failure with piezo ignition and a 30MJ oven burner.
Gas Supply Requirements
- Non CE Only
Input Rate (N.H.G.C.)
- each Open Burner
- each 300 mm Griddle Section
- Oven
Supply Pressure
Burner Operating Pressure
Gas Connection
Natural Gas LP Gas (Propane)
28 MJ/hr
(26,540 Btu/hr)
21 MJ/hr
(19,900 Btu/hr)
28 MJ/hr
(26,540 Btu/hr)
21 MJ/hr
(19,900 Btu/hr)
30 MJ/hr
(28,434 Btu/hr)
1.13 - 3.4 kPa
(4.5” - 13.5” w.c.)
0.95 kPa (*)
(3.7” w.c.)
3
/
4
” B.S.P. Male
30 MJ/hr
(28,434 Btu/hr)
2.75 - 4.50 kPa
(11” - 18” w.c.)
2.6 kPa (*)
(10” w.c.)
3
Specifications
- CE Only
Appliance Classification
Category:
II
Flue Type:
A
2H3P
(20, 30 / 37).
1.
Natural Gas (G20) Propane (G31)
Open Burner
(each)
Heat Input
(nett)
Nominal
Reduced
Gas Rate
(nett)
6.5 kW
1.75 kW
Nominal
0.69 m
3
/hr
Reduced
0.19 m
3
/hr
Supply Pressure
Operating Pressure
Gas Connection
Griddle
(each 300mm section)
5.5 kW
1.85 kW
0.58 m
3
/hr
0.20 m
3
/hr
20 mbar
9.5 mbar
Oven
Open Burner
(each)
Griddle
(each 300mm section)
8.0 kW
2.4 kW
6.5 kW
1.75 kW
0.85 m
3
/hr 0.51 kg/hr
0.25 m
3
/hr 0.14 kg/hr
5.5 kW
1.95 kW
0.43 kg/hr
0.15 kg/hr
30 / 37 mbar
26 mbar
3
/
4
” B.S.P. Male
Oven
8.0 kW
2.4 kW
0.62 kg/hr
0.19 kg/hr
(
*
) The burner operating pressure is to be measured at the manifold test point with two burners operating at full setting. The operating pressure is ex-factory set, through the appliance regulator and is not to be adjusted, apart from when carrying out gas conversion, if required. (Refer to the ‘Gas Conversion’ section for details).
Gas Connection
Gas supply connection point is located at the rear of the appliance, approximately 130 mm from the right hand side, 35 mm from the rear and 655 mm from the floor and is reached from beneath the appliance. (Refer to the ‘Dimensions’ section).
Connection is ¾" BSP male thread.
4
G505
Cook Top Options
G505D G505C
Dimensions
5
Dimensions
G506
Cook Top Options
G506D G506C
G506B
6
G506A
Dimensions
G508
Cook Top Options
G508D
G508C
G508B G508A
7
Installation
Installation Requirements
NOTE:
• It is most important that this appliance is installed correctly and that operation is correct
before use. Installation shall comply with local gas and health and safety requirements.
• This appliance shall be installed with sufficient ventilation to prevent the occurrence of
unacceptable concentrations of health harmful substances in the room, the appliance is installed in.
Blue Seal Gas Range Static Ovens are designed to provide years of satisfactory service, and correct installation is essential to achieve the best performance, efficiency and trouble-free operation.
This appliance must be installed in accordance with National installation codes and in addition, in accordance with relevant National / Local codes covering gas and fire safety.
AUSTRALIA:
NEW ZEALAND:
UNITED KINGDOM:
- AS 5601
- NZS 5261
- Gas Installations.
- Gas Installation.
- Gas Safety (Installation & Use) Regulations 1998.
- BS 6173 - Installation of Catering Appliances.
IRELAND:
- BS 5440 1 & 2 - Installation Flueing & Ventilation.
- IS 820 - Non - Domestic Gas Installations.
Installations must be carried out by authorised persons only. Failure to install equipment to the relevant codes and manufacturer’s specifications shown in this section will void the warranty.
Components having adjustments protected (e.g. paint sealed) by the manufacturer are only to be adjusted by an authorised service agent. They are not to be adjusted by the installation person.
Unpacking
• Remove all packaging and transit protection from the appliance including all protective plastic coating from the exterior stainless steel panels.
• Check equipment and parts for damage. Report any damage immediately to the carrier and distributor.
• Report any deficiencies to the distributor who supplied the appliance.
• Check that the available gas and electrical supply is correct to that shown on the rating plate located on the front right hand corner of the bottom sill.
Location
1. Installation must allow for a sufficient flow of fresh air for the combustion air supply.
Combustion Air Requirements:
2. Installation must include adequate ventilation means, to prevent dangerous build up of combustion products.
3. Never directly connect a ventilation system to the appliance flue outlet.
4. Any gas burning appliance requires adequate clearance and ventilation for optimum and trouble-free operation. The minimum installation clearances shown below are to be adhered to.
5. Position the appliance in its approximate working position.
6. All air for burner combustion is supplied from underneath the appliance. The legs must always be fitted and no obstructions placed on the underside or around the base of the appliance, as obstructions will cause incorrect operation and/or failure of the appliance.
NOTE: Do not obstruct or block the appliances flue. Never directly connect a ventilation system to the appliance flue outlet.
8
Installation
Clearances
NOTE: Only non-combustible materials can be used in close proximity to this appliance.
Left/Right hand side
Rear
Combustible Surface
250 mm (*)
100 mm
Non Combustible Surface
0 mm
0 mm
* Side clearances can be 50 mm when the adjacent surface is at least 100 mm below the cooking surface.
Assembly
NOTE:
• All Models are delivered completely assembled. No further assembly is required.
• This appliance is fitted with adjustable feet to enable the appliance to be positioned
securely and level. This should be carried out on completion of the gas connection. Refer to the ‘Gas Connection’ section.
Optional Accessories (Refer to Replacement Parts List)
• Plinth Kit. For installation details, refer to the instructions supplied with each kit.
1. Check that all the feet (or castors) are securely fitted.
2. Adjust the four feet to make the Range steady and level.
Gas Connection
NOTE: ALL GAS FITTING MUST ONLY BE CARRIED OUT BY AN AUTHORISED PERSON.
1. Blue Seal Ranges do not require an electrical connection, as they function totally on the gas supply only.
2. It is essential that the gas supply is correct for the appliance to be installed and that adequate supply pressure and volume are available. The following checks should therefore be made before installation:- a. Gas Type the appliance has been supplied for, is shown on coloured stickers located above the gas connection point and rating plate. Check that this is correct for the gas supply the appliance is being installed for. The gas conversion procedure is detailed in this manual. b. Supply Pressure required for this appliance is shown in the “Specifications” section of this manual. Check the gas supply to ensure adequate supply pressure exists. c. Input Rate of this appliance is stated on the Rating Plate and in the ‘Specifications’ section of this manual. The input rate should be checked against the available gas supply line capacity. Particular note should be taken if the
appliance is being added to an existing installation.
Rating Plate will be located in this Area
Fig 1
NOTE: It is important that adequately sized piping runs directly to the connection joint on the appliance with as few tees and elbows as possible to give maximum supply volume.
3. Fit the gas regulator supplied, into the gas supply line as close to the appliance as possible.
NOTE: The gas pressure regulator provided with this appliance is convertible between Natural Gas and LPG as per the ‘Gas Conversion Section’ in this manual.
Ensure the regulator is converted to the correct gas type that the appliance will operate on.
The regulator outlet pressure is fixed ex-factory for the gas type that the regulator is converted to and it is NOT to be adjusted.
9
Installation
The regulator connections are
3
/
4
" BSP female.
The connection to the appliance is
3
/
4
" BSP male.
(Refer to the “Specifications” section for the gas supply location dimensions).
NOTE: A Manual Isolation Valve must be fitted to the individual appliance supply line.
4. Correctly locate the appliance into its final operating position and using a spirit level, adjust the legs so that the appliance is level and at the correct height.
5. Connect the gas supply to the appliance. A suitable joining compound which resists the breakdown action of LPG must be used on every gas line connection, unless compression fittings are used.
6. Check all gas connections for leakages using soapy water or other gas detecting equipment.
WARNING:
D
O NOT USE A NAKED FLAME TO CHECK FOR GAS LEAKAGES
.
7. Check that the gas operating pressure is as shown in “Specifications” section.
NOTE: The operating pressure to be measured at the manifold test point and with 2 burners operating at the “High Flame” setting.
8. Turn off the mains gas supply and bleed the gas out of the appliance gas lines.
9. Turn on the gas supply and the appliance.
10. Verify that the operating pressure remains correct.
Commissioning
M a n i f o l d
Test Point
Fig 2
1. Before leaving the new installation; a. Check the following functions in accordance with the operating instructions specified in the
‘Operation’ section of this manual.
• Lighting the Griddle.
• Lighting the Open Burners (F - Flame Failure Option).
• Lighting the Open Burners (PF - Pilot and Flame Failure Option).
• Check the Low Fire burner operation.
• Light the Oven Pilot and Main Burners.
• Check the Oven Main Burner Thermostat operation.
• Turning the Oven to ‘Stand-By’ Mode.
• Oven ‘Shut Down’. b. Ensure that the operator has been instructed in the areas of correct lighting, operation, and shutdown procedure for the appliance.
2. This manual must be kept by the owner for future reference, and a record of the
Date of
Purchase, Date of Installation and Serial Number of the Appliance recorded and kept with this manual. (These details can be found on the Rating Plate attached to the bottom right
hand corner of the bottom sill. Refer to the ‘Gas Connection’ section).
NOTE: If for some reason it is not possible to get the appliance to operate correctly, shut off the gas supply and contact the supplier of this appliance.
10
Operation
Operation Guide
C
AUTION
:
•
This appliance is for professional use and is only to be used by qualified people.
•
Only authorised service persons should be used to carry out installation, servicing or gas conversion operations.
•
Components having adjustments protected (e.g. paint sealed) by the manufacturer should not be adjusted by the user/operator.
1. Blue Seal appliances have been designed to provide simplicity of operation and 100% safety protection.
2. Improper operation is therefore almost impossible, however bad operation practices can reduce the life of the appliance and produce a poor quality product. To use this appliance correctly please read the following sections carefully:-
• Lighting the Open Burners (F - Flame Failure Option).
• Lighting the Open Burners (PF - Pilot and Flame Failure Option).
• Lighting the Griddle.
• Oven Pilot Ignition.
• Oven Main Burner / Thermostat.
• Turning the Oven to ‘Stand-By’ Mode.
• Oven ‘Shut-Down’.
Gas Control Knobs
Griddle Option
Burner Control
Description of Controls
OFF Position
PILOT Burner
HIGH Flame
LOW Flame
Piezo Igniter
(Griddles Only)
Open Burner Option
OFF Position
Fig 3
HIGH Flame
LOW Flame
Rear Burner
Front Burner
(Indicators are located above the Gas Control
Knobs).
Oven Option
OFF Position
PILOT Burner
Temperature
Graduations 100°C to
290°C
Piezo Igniter (Oven)
11
Operation
Open Burners
NOTE: Only cooking pans from size Ø 150 mm to Ø 420 mm are suitable fo use on these open burners.
Flame Failure Option (F-Models)
Lighting the Open Burners
Flame Failure Protection is incorporated for each burner by way of a thermo-electric system which will shut off the gas supply to that burner in the event that the burner goes out, so that un-burnt gas is not expelled. a. Select the burner required, depress and turn the corresponding gas control knob anti-clockwise to the ‘HIGH’ position. b. With the gas control knob depressed, manually light the burner. c. Release the gas control knob after approximately 10-20 seconds after lighting the burner. d. The burner should stay alight - if not, repeat Steps (a to (c above. e. To achieve simmer control, depress the gas control knob and rotate between the ‘HIGH’ and
‘LOW’ positions to achieve the temperature required.
Turning 'OFF' the Open Burners
a. When the main burner is not required, depress and turn the gas control knob clockwise back to the ‘OFF’ position. The 'MAIN' burner will extinguish.
Pilot and Flame Failure Option (PF-Models)
Lighting the Open Burners
These hobs are fitted with individual standing pilots for each open burner which allows the main burners to be turned 'ON' - 'OFF' without the need to manually re-light the burner each time that it is turned 'ON', as the burner will automatically light itself off the pilot burner.
Flame Failure Protection is incorporated for each burner by way of a thermo-electric system which will shut off the gas supply to that burner in the event that the burner goes out, so that un-burnt gas is not expelled. a. Select the burner required, depress and turn the corresponding gas control knob anti-clockwise to the ‘PILOT’ position. b. With the gas control knob depressed, manually light the pilot burner. c. Release the gas control knob after approximately 10-20 seconds after lighting the pilot burner. d. The pilot burner should stay alight - if not, repeat Steps (a to (c above. e. ‘Full Flame’ can now be achieved by depressing and rotating the gas control knob anti-clockwise to the first stop 'HIGH' flame position. f. Low flame can be achieved by depressing the gas control knob and rotating fully anti-clockwise to the ‘LOW' flame position. g. To achieve simmer control, depress the gas control knob and rotate between the ‘HIGH’ and
‘LOW’ positions to achieve the temperature required.
Turning 'OFF' the Open Burners / Pilots
a. To turn 'OFF' the main burner, but keep the pilot burner alight, rotate the gas control knob to the
'PILOT' position. The main burner will extinguish and the pilot will remain alight. b. To turn 'OFF' the 'PILOT', depress and turn the gas control knob clockwise back to the ‘OFF’ position. The 'PILOT' burner will extinguish.
12
Operation
Griddle
C
AUTION
:
The griddle plate temperature reaches over 300°C in hottest points during normal operation at 'Full Flame' setting .
Lighting the Griddle
a. Depress the gas control knob and rotate anti-clockwise to the ‘PILOT’ position. b. With the gas control knob depressed, press the piezo ignition button to ignite the pilot burner.
Repeat Items 1 to 2 until the pilot is lit. c. Release the gas control knob approximately 10-20 seconds after lighting the pilot. d. The pilot should now remain alight - if not, repeat Steps (a to (c above. e. ‘Full Flame’ can now be achieved by depressing and rotating the gas control knob anti-clockwise to the first stop. f. Low flame can be achieved by depressing the gas control knob and rotating fully anti-clockwise to the ‘Low Flame’ position. g. When the main burner is not required, depress and turn the gas control knob clockwise back to the ‘OFF’ position.
Turning 'OFF' the Griddle Burner / Pilot
a. To turn 'OFF' the griddle, but keep the pilot burner alight, rotate the gas control knob to the
'PILOT' position. The griddle burner will extinguish and the pilot will remain alight. b. To turn 'OFF' the 'PILOT', depress and turn the gas control knob clockwise back to the ‘OFF’ position. The 'PILOT' burner will extinguish.
13
Operation
Lighting the Oven Pilot Burner
! IMPORTANT
DO NOT USE aluminium foil or trays directly on the cast iron sole plate(s). NEVER block or cover the openings on each side of the sole plate(s).
This oven is fitted with a pilot as a standard option and flame failure protection, which is incorporated by way of a thermo-electric system for the main burner. Flame failure protection will shut off the gas supply to the burner in the event that the pilot burner goes out, so that un-burnt gas is not expelled.
This is an important safety feature which is
slowly becoming law throughout the world.
1. Open the oven door. Partially depress the thermostat control knob whilst turning anti-clockwise to the ‘Pilot’ position. DO NOT fully depress the Control Knob
whilst trying to rotate anti-clockwise as the Knob
and Gas Valve will be damaged.
2. With the thermostat control knob in the ‘Pilot’ position, keep the knob depressed whilst pressing the piezo igniter button. (Each press of the piezo igniter button will generate a single spark).
3. Hold in the thermostat control knob depressed for approx. 10-20 seconds, then release. The pilot burner should remain alight. (If the pilot does not light, repeat
Items 1 to 3 above).
4. View the oven pilot burner through the holes in the front of the sole plate with the oven door open.
Lighting the Oven Main Burner
1. Ensure that the pilot burner is alight.
2. Rotate the thermostat control knob anti-clockwise to the desired temperature marked on the knob.
3. The main burner will now ignite automatically, from the pilot burner.
Turning the Oven to ‘Stand-by’ (Pilot ‘ON’ Only)
NOTE: DO NOT attempt to rotate the T hermostat Control
Knob anti-clockwise back to the ‘Pilot’ position as the Knob and Gas Valve will be damaged.
1. Rotate the thermostat control knob clockwise to the
‘Pilot’ position. The main burner will extinguish and the pilot burner will remain alight.
Pilot Burner viewing holes
Piezo Igniter
Button
Fig 4
Control Knob in
Pilot Position
Depress and Rotate Knob
Anti-Clockwise to Pilot Position
Control Knob in Main
Burner Operating Position
Rotate Knob Anti-Clockwise to Operating Temperature
Control Knob in
Pilot Position
Piezo Igniter
Button
Rotate Knob Clockwise to Pilot Position
14
Oven ‘Shut-Down’
NOTE: DO NOT attempt to rotate the T hermostat Control
Knob anti-clockwise back to the ‘O’ Off position as the Knob and Gas Valve will be damaged.
1. To turn 'Off' the oven completely, partially depress the thermostat control knob whilst turning clockwise to the
'O' Off position, the pilot burner will extinguish. DO NOT
fully depress the Thermostat Control Knob whilst trying to rotate clockwise to the ‘O’ Off position as
the Knob and Gas Valve will be damaged.
Operation
Control Knob in
’Off’ Position
Partially Depress and Rotate
Knob to the ‘O’ Off Position.
! IMPORTANT
Should any abnormal operation like;
- ignition problems,
- abnormal burner flame,
- burner control problems,
- partial or full loss of burner flame in normal operation, be noticed, the appliance requires
IMMEDIATE service by a qualified service person and should not be used until such service is carried out.
15
Cleaning and Maintenance
C
AUTION
:
Always turn off the gas supply before cleaning.
This appliance is not water proof.
Do not use water jet spray to clean interior or exterior of this appliance.
General
Clean the range regularly. A clean range looks better, will last longer and will perform better.
Carbonised grease on the surface or between the trivets, griddle plates will hinder the transfer of heat from the cooking surface to the food. This will result in loss of cooking efficiency.
NOTE: Each griddle option can be supplied with a scraper tool and a pack of blades for cleaning the griddle surface. These are not supplied with the griddle and have to be purchased separately. Refer to the 'Replacement Parts List' at the rear of this manual.
WARNING:
T
HE BLADES FITTED TO THE SCRAPER TOOL ARE EXTREMELY SHARP AND ARE TO BE USED WITH CARE
.
DO NOT use water on the trivets, burners and griddle plates while these items are still hot as warping and cracking may occur. Allow these items to cool down and then
remove for cleaning. The entire trivets, griddle plates and burner caps can be removed for cleaning.
NOTE:
• DO NOT use abrasive detergents, strong solvents or caustic detergents as they could
corrode or damage the range.
• In order to prevent the forming of rust on the trivets, griddle plates (If fitted) and burners,
ensure that any detergent or cleaning material has been completely removed after each cleaning. The appliance should be switched on briefly to ensure that the griddle plates become dry. Oil or grease should be spread over the griddle surface in order to form a thin protective greasy film.
To keep your range clean and operating at peak efficiency, follow the procedures shown below:-
After Each Use
C
AUTION
:
Always ensure that an even pressure is applied over the whole surface of the scraper tool when using on the flat surface of the griddle, to prevent scoring of the surface.
NEVER bang the sharp edge of the scraper tool on the flat surface of the griddle as this will damage the finish and invalidate the warranty.
1. Clean the griddle with a scraper tool to remove any food debris.
2. Always ensure that the scraper tool blades are changed regularly to ensure that the scraper tool works efficiently and prevents damage to the griddle plate surface.
3. Clean the range castings with a stiff nylon brush or a flexible spatula to remove any food debris.
16
Cleaning and Maintenance
Daily Cleaning
1. The grease / spill tray(s) should be checked and emptied frequently to prevent overflow and spillage. Remove the grease / spill tray(s) while still warm so that the grease is in a liquid state.
Empty any grease from the trays and wash thoroughly in the same manner as any cooking utensil.
2. Remove the burner caps and bases, the trivets and thoroughly clean the splash back, interior and exterior surfaces of the range with hot water, a detergent solution and a soft scrubbing brush.
3. Brush griddle surface (optional - if fitted) with a soft bristled brush. Any carbon deposits should be removed using a scraper tool followed by wiping with a cloth to prevent build up of food deposits.
Clean control panel with a damp cloth moistened with a solution of mild detergent and water.
4. Dry the range thoroughly with a dry cloth and polish with a soft dry cloth.
Weekly Cleaning
NOTE:
• If the range usage is very high, we recommend that the weekly cleaning procedure is
carried out on a more frequent basis.
• Ensure that protective gloves are worn during the cleaning process.
• DO NOT use harsh abrasive detergents, strong solvents or caustic detergents as they will
damage the range, burners and plates.
• DO NOT use water on the trivets, griddle plates and burners while they are still hot as
cracking may occur. Allow these items castings to cool and remove for cleaning.
• DO NOT clean the burners in a dishwasher.
Range Cooking Area
a. Clean the range cooking area using a soft cloth moistened with a mild detergent and hot water solution. b. Baked on deposits or discolouration may require a good quality stainless steel cleaner or stainless steel wool. Always apply cleaner when the appliance is cold and rub in the direction of the grain. c. It should not be necessary to remove the splash guards covering the burner manifolds for cleaning purposes. These can be cleaned in situ. d. Remove the grease tray and clean with a mild anti bacterial detergent and hot water solution using a soft bristled brush. e. Dry the grease tray thoroughly with a dry cloth.
Griddle Plate - (Steel)
NOTE: In order to prevent the forming of rust on the griddle plate, ensure the detergent or cleaning material has been entirely removed after each cleaning process. The appliance should be switched on briefly to ensure the griddle plates become dry. Oil or grease should be spread over the griddle surface in order to form a thin protective greasy film.
C
AUTION
:
Always ensure that an even pressure is applied over the whole surface of the scraper tool when using on the flat surface of the griddle, to prevent scoring of the surface.
NEVER bang the sharp edge of the scraper tool on the flat surface of the griddle as this will damage the finish and invalidate the warranty.
a. Remove and clean the grease / spill trays frequently to prevent over spills. b. Clean the griddle surface thoroughly with the supplied scraper tool or a wire brush. If necessary use a griddle stone or a scotch bright pad on the griddle surface. c. A scraper tool can be used for the removal of stubborn carbon and deposits. d. Occasionally bleach the griddle plate with vinegar when the plate is cold. e. Clean with hot water, a mild detergent solution and a scrubbing brush. Dry all components thoroughly with a dry cloth. f. The griddle should be switched on briefly to ensure that the griddle plate becomes dry. A thin smear of cooking oil should be spread over the griddle plate in order to form a protective film.
17
Cleaning and Maintenance
Trivets and Burners
a. Remove the trivets from the top of the appliance, taking note that the trivets are manufactured with a lip on one edge, the lip must always be fitted to the outer edge (front and back) of the cook top. (Refer to Fig 10 overleaf). b. Remove the burner cap and burner bowl (these are a loose fit to the manifold, see Fig 5) from the top of the gas manifold, taking care not to damage the thermocouple (and pilot tube for -PF Option) fitted through the manifold splash guard. (Refer to Fig 8 for F Option and Fig 9 for PF Option). c. The trivets and burners should be cleaned with a mild detergent and hot water solution using a soft bristled brush. Dry thoroughly with a dry cloth.
Burner Cap
Burner Bowl
Fig 5
Notice Difference in Profiles
Trivet Supports
a. Remove all the trivet supports from the top of the appliance. Take note of the orientation of the trivet support when removing. The trivet support front end side rail profiles are different from the rear end side rail profiles.
(See the Note shown at Item a in
‘Re-Fitting the Components to the Range’ overleaf and Fig 6). b. The trivet supports should be cleaned with a mild detergent and hot water solution using a soft bristled brush. c. Dry the trivet supports thoroughly with a dry cloth.
Stainless Steel Surfaces
a. With the griddle plates and burners removed, clean the interior and exterior surfaces of the range with hot water, a mild detergent solution and a soft scrubbing brush. Note that the gas control knobs are a push fit onto the gas control valve spindles and can be removed to allow cleaning of the front of the control panel. b. Baked on deposits or discolouration may require a good quality stainless steel cleaner or stainless steel wool. Always apply cleaner when the appliance is cold and rub in the direction of the grain. c. It should not be necessary to remove the splash guards covering the burner manifolds for cleaning purposes. These can be cleaned in situ. d. Dry all components thoroughly with a dry cloth and polish with a soft dry cloth. e. To remove any discolouration, use an approved stainless steel cleaner or stainless steel wool. Always rub in the direction of the grain. f. Remove the grease tray and clean with a mild anti bacterial detergent and hot water solution using a soft bristled brush. g. Dry the grease tray thoroughly with a dry cloth. h. Dry all components thoroughly with a dry cloth and polish with a soft dry cloth.
Burner Bowl
Locating Holes
F - Option
Burner Base Locates onto
Cap Screw and over Flange
Pilot Burner
PF - Option
Re-Fitting the Components to the Range
a. Refit the trivet supports to the range, ensuring that the trivet supports are correctly fitted.
Burner Base
Shown without Pilot
Burner Shield fitted.
18
Fig 6
Fig 7
Fig 8
Thermocouple
Fig 5
Fig 9
Cleaning and Maintenance
NOTE: It is imperative that the trivet supports are correctly re-fitted to the appliance to ensure that the trivets locate correctly and sit flush and level. NOTE that the trivet support front end, side rail profiles are different at either side (See Fig 6) and only one of the side rails seat into the cut-out in the range top, where as the rear end of the trivet support side rail profiles are the same and have 2 cut-outs to locate into.
Notice Lip on
Trivet Edge b. Refit the burner bowls onto the manifolds protruding through the splash guards, taking care not to damage the thermocouple (and pilot tube for -PF Option) which is close to the manifold.
Fig 10
NOTE: The burner bowl (cast item) has 2 locating holes drilled into the base flange, (See Fig 7) these are to locate the burner bowl to the cap screw on the gas manifold when re-fitting the burner bowl onto the gas manifold (Refer to Fig 8 {F-Option} and Fig 9 {PF-Option}).
c. Refit the burner caps (cast brass) onto the burner bowls already fitted to the manifold. These are a loose fit into the burner bowls. d. Refit the trivets to the cook top, taking note that the trivets are manufactured with a lip on one edge, the lip must always be fitted to the outer edge (front and back) of the range. (See Fig 10). e. Refit the spill / grease tray(s) to the range.
Oven Interior
a. Do not use wire brushes, steel wool or other abrasive materials to clean the oven interior. b. Clean the oven regularly with a good quality domestic oven cleaner. c. Once a week, remove and clean any built up of grease etc. from the oven racks and the bottom spill over cover. d. Dry the oven thoroughly with a dry cloth and polish with a soft dry cloth.
Periodic Maintenance
NOTE: All maintenance operations should only be carried out by a qualified service person.
To achieve the best results cleaning must be regular and thorough and all controls and mechanical parts should be checked and adjusted periodically by a qualified service person. If any small faults occur, have them attended to promptly. Don't wait until they cause a complete breakdown. It is recommended that the appliance is serviced every 6 months.
Gas Control Valve Re-Greasing
The gas control valve should be dismantled and greased every 6 months to ensure the correct operation of the gas control valve.
To carry out this operation;- a. Remove the gas control knobs from the gas tap spindles by pulling the knobs away from the control panel. b. Remove the drip tray from the appliance. c. Remove the two screws on the underside of the control panel, securing the control panel to the hob. d. Remove the control panel from the front of the appliance. e. Remove the 2 screws holding shaft plate to gas control body and remove control shaft and plate. (Refer to Fig
11). Note orientation of shaft for correct re-assembly. f. Using needle nose pliers or similar, pull out gas control spindle, again noting its orientation. g. Apply a suitable high temperature gas cock grease or lubricant such as ROCOL - A.S.P (Anti scuffing paste) /
Dry Moly Paste to the outside of the spindle. (Refer to
Fig 12).
h. Replace spindle and re-assemble the gas control in reverse order. i. Refit the control panel to the appliance and secure with 2 screws. j. Refit the knobs to the gas control valve spindles.
Two Screws
Spindle
Fig 11
Fig 12
19
Fault Finding
This section provides an easy reference guide to the more common problems that may occur during the operation of your appliance. The fault finding guide in this section is intended to help you correct, or at least accurately diagnose problems with your equipment.
Although this section covers the most common problems reported, you may encounter a problem not covered in this section. In such instances, please contact your local authorised service agent who will make every effort to help you identify and resolve the problem. Please note that the service agent will require the following information:-
• The Model Trade Name and the Serial Number of the Appliance. (both can be found on
the Technical Data Plate located on the appliance.
Fault
Pilot will not light.
Possible Cause
No gas supply.
Blocked pilot injector.
Remedy
Ensure gas isolation valve is turned on, and that bottles are not empty.
Call the service provider.
Pilot goes out when gas control knob released.
Releasing knob before the thermocouple has heated.
Pilot flame too small.
- Gas pressure too low.
- Partially blocked pilot injector.
Thermocouple connection to the gas control is loose or faulty.
Thermocouple faulty.
Electromagnet in the rear of the gas control unit is faulty.
Hold knob in for at least 20 seconds following ignition of the pilot.
Clean or replace the pilot injector.
Tighten the thermocouple connection.
Check that the thermo couple is producing between 20-30mV.
Inspect and replace if not in good working order.
Call the service provider.
Main burner will not light. Incorrect supply pressure.
Faulty gas control.
Call the service provider.
Call the service provider.
Piezo Ignition spark is being generated but not sparking from the ignition electrode to the pilot burner hood. (Griddle and Oven options only)
HT lead damaged or broken.
Check that the ignition electrode is not cracked and is correctly positioned.
Piezo igniter faulty.
Repair or replace the HT lead.
Re-position or replace the ignition electrode.
Replace the piezo igniter.
Call the service provider.
NOTE: Components having adjustments protected (e.g. paint sealed) by the manufacturer, are only to be adjusted by an authorised service agent. They are not to be adjusted by an unauthorised service person.
20
Gas Conversion and Specifications
Conversion Procedure
C
AUTION
:
Ensure that the appliance is isolated from the gas supply before commencing servicing.
NOTE:
• These conversions should only be carried out by
qualified persons. All connections must be checked for leaks before re-commissioning the appliance.
• For all relevant gas specifications refer to the table at
the end of this section.
Open Burners ('F' - Flame Failure Option)
Burner
Cap
1. Turn ‘OFF’ the gas supply at the main supply.
2. Remove the trivets from the top of the appliance, taking note that the trivets are manufactured with a lip on one edge, the lip must always be fitted to the outer edge (front and back) of the range. (See Fig 18).
3. Remove the burner caps and burner bowls (these are a loose fit to the manifold) (See Fig 13) from the top of the gas manifold, taking care not to damage the thermocouples fitted through the manifold splash guard.
4. Remove all the trivet supports from the top of the appliance.
Note the orientation of the trivet supports when removing. The trivet support front end side rail profiles are different from the rear end side rail
profiles. (See Fig 14).
5. Remove the splash guards covering the burner manifolds by unscrewing the two allan headed screws. Carefully remove the splash guards taking care not to damage the thermocouples protruding through the splash guard. (See Fig
15).
6. Unscrew and remove the injectors (½ A/F) from the gas cocks. (See Fig 16).
7. Determine the correct injector sizes for the corresponding gas from the rating plate affixed to the lower right hand side of the front sill.
8. Replace with the correct size injectors. Refer to the ‘Gas
Specifications table’ at the end of this section, for correct injector sizes.
9. Refit the splash guards over the gas cocks taking care not to damage the thermocouples and secure in position with the 2 allan headed screws. (See Fig 15).
10. Refit the burner caps and burner bowls onto the manifolds protruding through the splash guards, taking care not to damage the thermocouple which is close to the manifold.
Take note that the base part of the burner bowl has 2 locating holes drilled into the base flange (See Fig 17), these are to locate the burner bowl onto the allen headed screws that secure the splash guard to the gas manifold. (See Fig 15).
11. Turn on the gas supply at the mains, re-light the burners and check the flame size on the simmer 'LOW' position.
NOTE: The right hand gas control valve supplies the rear burner and the left hand gas control valve supplies the front burner.
Burner
Bowl
Notice Difference in Profiles
Thermocouple
Splash Guard
Retaining Cap Screw
Open Burner
Injector
Burner Bowl
Locating Holes
Fig 13
Fig 14
Fig 15
Fig 16
Fig 17
21
Gas Conversion and Specifications
12. Refit all the trivet supports to the top of the appliance. Note the orientation of the trivet support when re-fitting as the front end side rail profiles are different from the rear end side rail profiles. (See Fig 14).
13. Refit the trivets to the top of the appliance taking note that the trivets are manufactured with a lip on one edge, the lip must always be fitted to the outer edge (front and back) of the cook top. (See Fig 18).
Low Fire Adjustment
a. To adjust the open burner low fire adjustment, remove the gas control knobs from the front of the control panel. b. Adjust the low fire adjustment screw on the open burner gas control valves to obtain the desired flame size. (See
Fig 19).
NOTE: The ‘Low Fire Screw’ should be sealed with coloured paint on completion of the low fire adjustment.
Open Burners ('PF' - Pilot & Flame Failure Option)
1. Turn ‘OFF’ the gas supply at the main supply.
2. Remove the trivets from the top of the appliance, taking note that the trivets are manufactured with a lip on one edge, the lip must always be fitted to the outer edge (front and back) of the cook top. (Refer to Fig 18).
3. Remove the burner caps and burner bowls (these are a loose fit to the manifold) from the top of the gas manifold.
4. Remove all the trivet supports from the top of the appliance.
Note the orientation of the trivet supports when removing.
The trivet support front end side rail profiles are different from the rear end side rail profiles. (Refer to Fig 14).
5. Remove the pilot burner shields from over the pilot burners / thermocouples by removing the 2 screws securing the pilot burner shields to the splash guards. (Refer to Fig 21).
6. Remove the splash guards covering the burner manifolds by unscrewing the two allan headed screws. Carefully remove the splash guards taking care not to damage the pilot burner tubes and thermocouples protruding through the splash guard.
Main Injectors
a. Unscrew and remove the main injectors (½ A/F) from the gas cocks. (See Fig 22).
b. Replace with the correct size injectors. Refer to the ‘Gas
Specifications table’ at the end of this section and the
Rating Plate attached to the underside of the right hand side, front oven lower trim for correct injector sizes for the corresponding gas.
Low Fire Adjustment Screw
Pilot Burner
Shield
2 Pilot Burner
Shield Screws
Main Injector
Notice Lip on
Trivet Edge
Fig 18
Fig 19
Fig 20
Fig 21
Pilot Injector
Plug
Fig 22
22
Gas Conversion and Specifications
Pilot Injectors
a. Unscrew and remove the Pilot Injector Plug from the fitting at the end of the pilot injector tube using a 11 mm A/F spanner. ( Refer to Fig 23).
b. Using a flat bladed screwdriver, unscrew and remove the pilot injector from the pilot injector housing.
NOTE Take care not to lose the spring fitted in front of the injector.
c. Remove existing pilot injector and replace with the correct size pilot injector for the gas type being used. Refer to the
‘Gas Specifications’ table at the end of this section, for correct pilot injector sizes. d. Refit the spring and the correct pilot injector to the pilot injector housing. e. Screw the pilot injector fully home using a flat blade screwdriver and refit the pilot injector plug to the pilot injector housing and tighten in place using a 11 mm A/F spanner. (Refer to Fig 23).
f. Refit the splash guard over the gas cocks taking care not to damage the thermocouples and pilot burner tubes. S ecure in position with the 2 allan headed screws. (Note that the splash guard for 'PF' models has a different cut-outs for pilot burner tubes. Refer to Fig 24 & Fig 25).
g. Refit the pilot burner tube shields over the pilot burner tubes / thermocouples and secure in place with the 2 securing screws. (Refer to Fig 21). h. Refit the burner caps and burner bowls onto the manifolds protruding through the splash guards. Take note that the base part of the burner bowl has 2 locating holes drilled into the base flange, (Refer to Fig 17).
these are to locate the burner bowl onto the allen headed screws that secure the splash guard to the gas manifold. (Refer to Fig 15).
i. Refit all the trivet supports to the top of the appliance.
Note the orientation of the trivet support when re-fitting as the front end side rail profiles are different from the rear end side rail profiles. (Refer to Fig 14). j. Refit the trivets to the top of the appliance taking note that the trivets are manufactured with a lip on one edge, the lip must always be fitted to the outer edge (front and back) of the cook top. (Refer to Fig 18).
Low Fire Adjustment
a. To adjust the open burner low fire adjustment, remove the gas control knobs from the front of the control panel. b. Adjust the low fire adjustment screw on the open burner gas control valves to obtain the desired flame size. ( Refer to Fig 26).
NOTE: The ‘Low Fire Screw’ should be sealed with coloured paint on completion of the low fire adjustment.
Pilot Injector
Housing
Pilot Injector
Plug
Cut-Out for Pilot
Burner &
Thermocouple
Pilot Burner
Shown without Pilot
Burner Shield fitted.
Low Fire Adjustment Screw
Fig 23
Fig 24
Thermocouple
Fig 25
Fig 26
23
Gas Conversion and Specifications
Griddle
Pilot Burner
a. With the gas supply turned off at the main supply, remove the griddle plate section by lifting it straight off the cook top. b. Remove the gas control heat shield from around the griddle burner, this is just a push in fit. c. Disconnect the thermocouple and the piezo igniter from the mounting bracket. (For access purposes).
(See Fig 27).
d. Disconnect the pilot supply tube from the pilot burner with a 13 mm (½") spanner. (See Fig 27).
e. Remove existing pilot injector and replace with the correct size for the gas being used. Refer to the
‘Gas Specifications’ table at the end of this section, for correct injector sizes. f. Re-connect the pilot supply tube to the pilot burner with a 13 mm (½") spanner. (See Fig 28).
g. Refit the piezo igniter and thermocouple to the mounting bracket. (See Fig 28). h. Repeat Items a) to g) for all griddle pilot burners.
Main Burner
a. Remove the main burner from the burner box by removing the securing screw at the end of the burner, this will reveal the main burner injector.
(See Fig 27).
b. Remove and replace the main burner injectors with correct size injectors. Refer to the ‘Gas
Specifications’ table at the end of this section, for correct injector sizes. c. Refit the burner to the griddle burner box. d. Refit the gas control heat shield to the griddle burner box. e. Refit the griddle plate section to the top of the cook top. f. Repeat Items a) to e) for all griddle main burners. g. Turn ‘ON’ the gas supply at the mains, re-light the griddle burners and check the flame size on the
‘LOW’ flame position.
Low Fire Adjustment
a. To adjust the griddle burner ‘LOW’ fire adjustment, remove the griddle gas control knobs from the front of the control panel. b. Adjust the low fire adjustment screw on the griddle gas control valve only, to obtain the desired flame size. (See Fig 29).
NOTE: The ‘Low Fire Screw’ should be sealed with coloured paint on completion of the low fire adjustment.
Gas Control
Heat Shield
Thermocouple Piezo Igniter
Pilot Burner
Low Fire Adjustment Screw
Burner
Securing
Screw
Fig 27
Fig 28
Fig 29
24
Gas Conversion and Specifications
Oven
Injector:
a. With the gas supply turned off at the main supply, unscrew and remove the 6 screws securing the lower lintel to the front of the oven. (See Fig 30).
b. Open the oven door and remove the cast oven sole plate from inside the oven. c. Remove the 2 screws securing the oven burner in the oven and remove the main burner from the oven. d. The main injector will now be exposed and can be unscrewed and removed using a 13 mm ( spanner. (See Fig 31).
1/
2
” A/F) e. Remove the main injector and replace with the correct size injector. (Refer to the ‘Gas
Specifications’ table at the rear of this section). f. Refit the main burner to the oven and secure in position with the 2 screws.
Pilot:
a. To remove the oven pilot injector, from inside the oven, unscrew and remove the thermocouple and piezo igniter from the mounting bracket. (See Fig
32).
b. Unscrew the hex nut holding the pilot supply tube to the rear of the pilot assembly. c. Withdraw the pilot injector from the pilot assembly. d. Replace the pilot injector with the correct sized injector for the gas type being used and re-connect the pilot supply tube to the pilot assembly. (See Fig 32).
e. Refit the vitreous enamelled tray to the oven.
Low Fire:
a. To change the thermostat ‘Low Fire’ screw for the gas type required, remove the gas control knob from the oven control panel. The gas control knob is a push fit onto the shaft of the oven gas control valve. Remove the gas control knob. b. Unscrew the single screw at the top of the oven control panel, securing the panel and lift the panel away from the oven. c. Unscrew and remove the old ‘Low Fire’ screw (See
Fig 33) from the lower left hand front of the valve and fully screw in the new ‘Low Fire’ screw for the new gas type. (Refer to the ‘Gas Specifications’ table at the rear of this section for screw types). d. Close the control panel and secure with the securing screw. e. Refit the oven gas control knob to the spindle of the oven gas control valve.
Shown with door removed for ease of viewing
Thermocouple
Low Fire
Screw
6 screws
Main Injector
Fig 30
Fig 31
Pilot Assembly
Piezo Igniter
Pilot Supply Line
Fig 32
Fig 33
25
Gas Conversion and Specifications
Gas Regulator
NOTE: The regulator supplied is convertible between Natural Gas and LPG, but it’s outlet pressure is fixed ex-factory and is NOT to be adjusted.
NOTE, Pin rotated for Natural Gas
NOTE, Pin rotated for LPG
Fig 34
1. Ensure that the gas supply is turned ‘OFF’ at the mains supply.
2. Unscrew the hexagonal cap (23mm A/F) from the regulator.
3. Un-clip the plastic pin from the cap, rotate the pin and re-fit it back to the cap the correct way for the gas type to be used. (Either ‘LP’ or
‘NAT’ should be visible on the flank of the pin once
re-fitted to the cap).
4. Screw the cap back into the regulator and tighten hand tight.
Gas Type Identification Label
On completion of the gas conversion, replace the gas type identification labels, located at:-
- The rear of the appliance, above the gas connection.
- Beside the rating plate.
26
Gas Conversion and Specifications
Commissioning
Before leaving the converted installation;
1. Check all gas connections for leakages using soapy water or other gas detecting equipment.
WARNING:
D
O NOT USE A
NAKED FLAME
TO CHECK FOR GAS LEAKAGES
.
2. Check the following functions in accordance with the operating instructions specified in the
‘Operation’ section of this manual.
• Light the Pilot Burners.
• Light the Main Burners.
• Check the Low Fire Burner operation.
• Check the High Fire Burner operation.
• Ensure that all the controls operate correctly.
• Ensure that the operating pressure remains correct.
NOTE: If for some reason it is not possible to get the appliance to operate correctly, shut off the gas supply and contact the supplier of this appliance.
Gas Specifications
- Australia / New Zealand Only
Open Burner
Main Burner Injectors
Pilot Burner ('PF' Option Only)
Griddle
Oven
Main Burner
Pilot Burner
Main Burner
Pilot Burner
Burner Aeration Setting
Low Fire
Supply Pressure
Burner Operating Pressure
Natural Gas
Ø 2.45 mm
0.30
Ø 2.10 mm
0.35
Ø 2.60 mm
0.35
Fully open
Ø 1.5 mm
1.13 - 3.40 kPa
0.95 kPa (*)
LP Gas (Propane)
Ø 1.50 mm
0.20
Ø 1.30 mm
0.23
Ø 1.60 mm
0.23
Fully open
Ø 0.95 mm
2.75 - 3.40 kPa
2.6 kPa (*)
Gas Regulator Cap Screw
*
The burner operating pressure is to be measured at the manifold test point with two burners operating at the ‘High’ setting. The operating pressure is ex-factory set, through the appliance regulator and is not to be adjusted, apart from when carrying out gas conversion, if required. (Refer to the ‘Gas Conversion’ section for details).
27
Gas Conversion and Specifications
- CE Only
Appliance Classification
Category:
II
Flue Type:
A
1.
2H3P
(20, 30 / 37).
Main Burner Injectors
Open Burner
Pilot Burner ('PF' Models Only)
Griddle
Oven
Main Burner
Pilot Burner
Main Burner
Pilot Burner
Burner Aeration Setting
Low Fire
Supply Pressure
Burner Operating Pressure
Natural. Gas
(G20)
Ø 2.30 mm
0.30
Ø 2.10 mm
0.35
Ø 2.60 mm
0.35
Fully open
Ø 1.5 mm
20 mbar
9.5 mbar (*)
Propane
(G31)
Ø 1.40 mm
0.20
Ø 1.30 mm
0.23
Ø 1.60 mm
0.23
Fully open
Ø 0.95 mm
30 / 37 mbar
26 mbar (*)
Gas Regulator Cap Screw
*
The burner operating pressure is to be measured at the manifold test point with two burners operating at the ‘High’ setting. The operating pressure is ex-factory set, through the appliance regulator and is not to be adjusted, apart from when carrying out gas conversion, if required. (Refer to the ‘Gas Conversion’ section for details).
28
Replacement Parts
Replacement Parts List
IMPORTANT:
Only genuine authorized replacement parts should be used for the servicing and repair of this appliance. The instructions supplied with the parts should be followed when replacing components.
For further information and servicing instructions, contact your nearest authorized service branch (contact details are as shown on the reverse of the front cover of this manual).
When ordering replacement parts, please quote the part number and the description as listed below. If the part required is not listed below, request the part by description and quote model number and serial number which is shown on the rating plate.
Cook Top
Open Burners
030245
030150
030230
030140
Injector
Injector
Injector
Injector
Bowl.
Cap.
026134 Pilot
026136 Pilot Injector
(Natural Gas)
(LP Gas [Propane])
(Natural Gas - G20)
(Propane - G31)
(LP Gas [Propane])
229442
229444 Pilot
227405
227379
228167
228166
Pilot Bracket Assembly.
Gas Control (with Flame Failure).
Knob - Open Burner.
Thermocouple - Front.
Thermocouple - Rear.
Ø 2.45 mm (Non UK).
Ø 1.50 mm (Non UK).
Ø 2.30 mm (UK Only).
Ø 1.40 mm (UK Only).
0.30
0.20.
Griddle
014105 Burner.
032210
032130
Injector
Injector
227403 Gas Control
227378 Knob Griddle.
(Natural Gas) Ø 2.10 mm.
(LP Gas [Propane]) Ø 1.30 mm.
(with Flame Failure and Pilot).
026488 Pilot
019217 Pilot Orifice (LP Gas [Propane]) 0.23.
019428 Thermocouple.
227508 Piezo
228047
018744
228288
Piezo H.T. Lead.
Piezo Ignition Electrode.
Grease Tray (Griddle Plates).
29
Replacement Parts
Oven
Oven Burner.
Oven Pilot.
020253
032260
032160
228703
230118
228963
Oven Burner Injector
Oven Burner Injector
(Nat Gas)
(LPG)
Ø 2.60mm.
Ø 1.60mm.
(Nat. 0.35.
(LPG) 0.23.
Thermostat / Gas Control Kit.
Low Fire Screw
Low Fire Screw
(Nat. Gas)
(LPG)
Ø 0.90mm.
Ø 0.55mm.
230363
General
Knob Oven - (100 - 275°C).
227014 Pot Stand / Trivet.
228884 Spill
Tray
228882 Spill
227892
227893
227850
Oven Side Rack LH.
Oven Side Rack RH.
227896 Oven
Adjustable Leg - 150mm.
229674 Rear
Regulator
228531 Regulator (Natural Gas/LP Gas [Propane] Convertible) ¾” BSP F/F.
Gas Conversion Kits
Models
G505
G506
G508
G505
G506
G508
Gas Type to Convert to
Australia / New Zealand Only
Nat. Gas (G20) LPG (Propane) (G31) Nat. Gas
UK Only
231909
231911
231913
231915
231917
231919
231908
231910
231912
231914
231916
231918
231885
231889
231893
231897
231901
231905
LPG
231884
231888
231892
231896
231900
231904
Accessories
228566
228567
228568
228797
228800
228804
Griddle Scraper Tool.
Smooth Plate Scraper Blades (Pack of 5 blades).
Ribbed Plate Scraper Blade (Individual Blade).
750 mm Plinth Kit.
900 mm Plinth Kit.
1200 mm Plinth Kit.
30
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement