advertisement
AR13D RIDE-ON ROLLER — OPERATION
OPERATION
Parking Brake
1. To release the parking brake, press and hold the release button (Figure 21) pull up slightlyon the parking lever, then push the parking brake lever all the way down.
3. Try manuvering the roller a few times to get familar with the handling. Also place the travel lever in the oposite direction to get acquainted with driving in reverse.
4. Make sure that the roller comes to a complete stop (neutral) before placing the travel lever in either a forward or reverse position.
Vibration Button
1. To begin the vibratory action, press the vibratory pushbutton switch located on top of the travel lever as shown in Figure 23. The pressing of this switch will generate 3,100 lbs. (1,406 Kg.) of centrifugal force at a frequency of 4000 vpm (vibrations per minute) to the front drum.
Figure 21. Brake Release Lever
Shift Lever
1. To make the roller move in a forward direction, move the shift lever forward as shown in Figure 22.
Figure 22. Shift Lever
2. Remember the speed of the roller is directly proportional to the amount of pressure being applied to the lever in each direction. Travel speed is between 0 and 4.8 mph (7.2 kph).
Figure 23. Vibration Pushbutton Switch
2. To stop the vibratory action, press the vibratory pushbutton switch again.
Sprinkler Controls
1. If the application requires the wetting of a surface, front and rear drum sprinkler controls have been provided. These controls (Figure 24) are located to the bottom right of the operators seat. The front valve controls the water supply to the front drum spray bar and the back valve contols water flow to the back drum spray bar.
FRONT
BACK
CAUTION - Drive System Safety
ALWAYS allow the roller to come to a complete stop before changing the direction of travel. Changing directions before the roller comes to a complete stop will result in excessive
force being applied to the transmission and drive system, which will reduce the over service life of the system.
Figure 24. Sprinkler Controls
PAGE 26 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Proposition 65 Warning
- 4 Table Of Contents
- 5 Parts Ordering Procedures
- 6 Safety Message Alert Symbols
- 8 Rules For Safe Operation
- 11 Operation and Safety Decals
- 13 Specifications (Roller)
- 14 Specifications (Engine)
- 15 Dimensions
- 16 General Information
- 18 Roller Components
- 21 Engine Components
- 22 Inspection
- 25 Initial Start-Up
- 26 Operation
- 27 Maintenance
- 37 Preparation For Long-Term Storage
- 38 Manifold Test Ports
- 39 Hydraulic System Diagram
- 40 Electric Wiring Diagram
- 42 Hydraulic Hose Connectsion
- 44 Troubleshooting (Roller)
- 45 Troubleshooting (Engine)
- 48 Explanation Of Code In Remarks Column
- 49 Suggested Spare Parts
- 50 Name Plate and Decals
- 52 Front Drum Assembly
- 54 Exciter Assembly
- 56 Rear Drum and Chassis Assembly
- 58 Covers and Frame Articulation Lock Assy
- 60 Hood and Rear Panel Assembly
- 62 Steering Column and Hydraulic Artic. Assy
- 64 Articulation Arm Assembly
- 66 Hydraulic Drive Pump Assembly
- 68 Manifold and Hydraulic Oil Filter Assembly
- 70 Fuel Tank and Oil Drain Hose Assembly
- 72 Water Tank Assembly
- 74 Engine Mounting Assembly
- 76 Muffler Assembly
- 78 Air Cleaner Assembly
- 80 Radiator Assembly
- 82 Throttle Assy
- 84 Brake Control Assy
- 86 Battery Assy
- 88 Scraper Assy
- 90 Terms and Conditions of Sale