Reference Information. Extron electronics DTP DVI 301, DTP HDMI 301

Reference

Information

This section discusses the specifications, part numbers, and accessories for the

DTP DVI 301 Tx/Rx transmitter and receiver. Topics that are covered include:

• Specifications

• Part Numbers and Accessories

• Mounting the Transmitter or Receiver

Specifications

NOTES : • This product consists of a transmitter (DTP DVI 301 Tx) and a receiver (DTP DVI 301 Rx), sold separately, with twisted pair cables linking the transmitter and receiver.

• *Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output .

Video

Maximum data rate ........................ 6.75 Gbps (2.25 Gbps per color)

Maximum pixel clock ...................... 165 MHz

Resolution range ............................ Up to 1920x1200 or 1080p @ 60 Hz; 8, 10, or 12 bit color depth

Formats .......................................... RGB and YCbCr digital video

Standards ....................................... DVI 1.0, HDMI 1.3

Video input and loop-through — transmitter

Number/signal type ........................ 1 single link DVI-D (or HDMI*) input

1 single link DVI-D (or HDMI*) local loop-through

Connectors .................................... 2 female DVI-I

Interconnection between transmitter and receiver

Connectors .................................... 2 female RJ-45 per unit for 2 cables connecting the transmitter and receiver

TP1 output transmits digital video, embedded digital audio, RS-232, IR, and remote power.

TP2 output transmits analog stereo audio.

Termination standards .................... TIA/EIA T568A or T568B

Signal transmission distance ........... 330' (100 m) using CAT 5e/6 UTP or STP cable

Video output — receiver

Number/signal type ........................ 1 single link DVI-D (or HDMI*)

Connectors .................................... 1 female DVI-I

Audio

Gain ............................................... Unbalanced output: 0 dB; balanced output +6 dB

Frequency response ........................ 20 Hz to 20 kHz, ±0.05 dB

THD + Noise ................................... 0.03% @ 20 Hz to 20 kHz at maximum output

S/N ................................................. >90 dB, at maximum output (15 dBu), balanced (unweighted)

Stereo channel separation .............. >80 dB @ 1 kHz to 20 kHz

DTP DVI 301 • Reference Information 12

Audio input

Number/signal type ........................ 1 PC level stereo, unbalanced

Connectors .................................... (1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground)

Impedance ..................................... >10k ohms, DC coupled

Nominal level ................................. -10 dBV (316 mVrms)

Maximum level ............................... +7 dBV (unbalanced)

NOTE: 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu

Audio output

Number/signal type ........................ 1 stereo (2 channel), balanced/unbalanced

Connectors .................................... (1) 3.5 mm captive screw connector, 5 pole

Impedance ..................................... 50 ohms unbalanced, 100 ohms balanced

Gain error ...................................... ±0.1 dB channel to channel

Maximum level (600 ohm) .............. >+15 dBu, balanced

Control/remote — external device (pass-through, unidirectional or bidirectional)

Serial control port input/output

Transmitter .............................. RS-232 via (1) 3.5 mm, 5 pole captive screw connector for RS-232 control (±5 V)

(connector is shared with IR control port)

Receiver ................................... 1 set of proprietary signals on a female RJ-45 jack

Serial control port output/input

Transmitter .............................. 1 set of proprietary signals on a female RJ-45 jack

Receiver ................................... RS-232 via a 3.5 mm, 3 pole captive screw connector

Baud rates ...................................... Up to 115200 baud

Protocol ......................................... Data bits = 5 - 8

Stop bits = 1 or 2

Parity = odd, even, none

Flow control = XON, XOFF, none

Serial control pin configuration ....... 1 = Tx, 2 = Rx, 3 = GND

IR control port ................................ (1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)

TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz

IR control pin configuration ............ 3 = GND, 4 = IR Tx, 5 = IR Rx

General

Power supply .................................. External

Input: 100-240 VAC, 50-60 Hz

Output: 12 VDC, 1 A, 12 watts

Power consumption ....................... 7.6 watts, 12 VDC, total, for both transmitter and receiver

NOTE: Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the CAT 5/5e/6 cable.

Temperature/humidity .................... Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing

Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing

Cooling .......................................... Convection, no vents

Mounting

Rack mount ............................. Yes, with optional 1U high rack shelf

Furniture mount ...................... Yes, with optional under-desk mounting kit

Enclosure type ................................ Metal

DTP DVI 301 • Reference Information 13

Enclosure dimensions

Transmitter .............................. 1.0" H x 4.3" W x 3.0" D (quarter rack wide)

(2.5 cm H x 10.9 cm W x 7.6 cm D)

(Depth excludes connectors.)

Receiver ................................... 1.0" H x 4.3" W x 6.0" D (quarter rack wide)

(2.5 cm H x 10.9 cm W x 15.2 cm D)

(Depth excludes connectors.)

Product weight

Transmitter .............................. 0.5 lbs (0.3 kg)

Receiver ................................... 1.0 lb (0.5 kg)

Shipping weight ............................. 3 lbs (2 kg)

Vibration ........................................ ISTA 1A in carton (International Safe Transit Association)

Regulatory compliance

Safety ...................................... CE, c-UL, UL

EMI/EMC ................................. CE**, C-tick, FCC Class A**, ICES, VCCI

NOTE: **CE and FCC testing is conducted with STP (shielded twisted pair) cable.

MTBF ............................................. 30,000 hours

Warranty ........................................ 3 years parts and labor

NOTES : • All nominal levels are at ±10%.

• Specifications are subject to change without notice.

DTP DVI 301 • Reference Information 14

Part Numbers and Accessories

Transmitter/Receiver Pair Part Numbers

NOTE: The Tx/Rx is comprised of the transmitter and receiver pair, which are purchased separately.

DTP DVI 301 Model

DTP DVI 301 Tx transmitter

DTP DVI 301 Rx receiver

Part Number

60-1213-12

60-1213-13

Included Parts

These items are included with each DTP DVI 301 transmitter and receiver:

Included parts

DTP DVI 301 Tx Transmitter

12 VDC, 1 A external power supply with 3.5 mm, 2-pole captive screw connector

IEC power cord

3.5 mm, 3-pole captive screw connector (1)

Shielded RJ-45 connectors (4)

Self-adhesive shielded tape

DTP DVI 301 Setup Guide

DTP DVI 301 Rx Receiver

3.5 mm, 3-pole captive screw connector (1)

DTP DVI 301 Setup Guide

Part Number

70-775-01

Cables and Adapters

Cable

DVID SL Pro Series — DVI male-to-male cable, various lengths

HDMIF-DVID-M — HDMI female to DVI-D male adapter

Part Number

26-649-nn

26-616-01

DTP DVI 301 • Reference Information 15

Mounting Accessories

Mounting kit

RSF 123 3.5-inch deep 1U rack shelf kit (transmitter only)

RSB 123 3.5-inch deep 1U rack shelf (transmitter only)

RSU 126 6-inch deep 1U universal rack shelf kit

RSB 126 6-inch deep 1U basic rack shelf

RSU 129 9.5-inch deep 1U universal rack shelf kit

RSB 129 9.5-inch deep 1U basic rack shelf

MBU 125 under-desk mount kit

MBD 129 through-desk mount kit

PMK 350 low profile projector mount kit, white

Part Number

60-190-20

60-604-21

60-190-10

60-604-11

60-190-01

60-604-02

70-077-01

70-077-02

70-563-03

Mounting the Transmitter or Receiver

CAUTION: Installation and service must be performed by authorized personnel only.

The 1-inch high, quarter rack width DTP DVI 301 transmitter or receiver can be placed on a table, mounted in a rack, or mounted under a desk or table. The receiver can also be mounted on a projector bracket.

Tabletop Use

Affix the included rubber feet to the bottom of the unit and place it in any convenient location.

Mounting kits

Mount the unit using any of the mounting kits listed above, in accordance with the directions included with the kit.

UL Rack-Mounting Guidelines

The following Underwriters Laboratories (UL) requirements pertain to the installation of the unit into a rack.

1. Elevated operating ambient temperature — If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consider installing the equipment in an environment compatible with the maximum ambient temperature (TMA = +122 °F, +50 °C) specified by Extron.

2. Reduced air flow — Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.

3. Mechanical loading — Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.

4. Circuit overloading — Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

5. Reliable earthing (grounding) — Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (such as use of power strips).

DTP DVI 301 • Reference Information 16