- Computers & electronics
- Computer components
- System components
- Networking cards
- HP (Hewlett-Packard)
- NC380T
- User Guide
advertisement
Technician notes
In this section
WARNING: Only authorized technicians trained by HP should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module-level repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard.
WARNING: To reduce the risk of electric shock, personal injury, and damage to the equipment:
• Do not attempt to service any parts of the equipment other than those specified in the following procedure. Any other activities may require that you shut down the server and remove the power cord.
• Installation and maintenance of this product must be performed by individuals who are knowledgeable about the procedures, precautions and hazards associated with the product.
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against it. Pay particular attention to the plug, electrical outlet, and the point where the cord extends from the server.
CAUTION: To properly ventilate the system, you must provide at least 7.6 cm (3.0 in) of clearance at the front and back of the server.
CAUTION: The server is designed to be electrically grounded (earthed). To ensure proper operation, plug the AC power cord into a properly grounded AC outlet only.
NOTE: Any indications of component replacement or printed wiring board modifications may void any warranty.
Technician notes 4
Where to go for additional help
1.
2.
3.
4.
Go to the HP website ( http://www.hp.com
).
Click Software & Driver Downloads from the left menu bar.
Type the product name in the For product box and press Enter. For example, type NC370T.
Download the drivers, firmware, or documentation as needed.
HP contact information
For the name of the nearest HP authorized reseller:
• In the United States, see the HP US service locator webpage ( http://www.hp.com/service_locator ).
• In other locations, see the Contact HP worldwide (in English) webpage
( http://welcome.hp.com/country/us/en/wwcontact.html
).
For HP technical support:
• In the United States, for contact options see the Contact HP United States webpage
( http://welcome.hp.com/country/us/en/contact_us.html
). To contact HP by phone: o Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day, 7 days a week. For continuous quality improvement, calls may be recorded or monitored. o If you have purchased a Care Pack (service upgrade), call 1-800-633-3600. For more information about Care Packs, refer to the HP website ( http://www.hp.com
).
• In other locations, see the Contact HP worldwide (in English) webpage
( http://welcome.hp.com/country/us/en/wwcontact.html
).
Technician notes 5
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 HP NC380T PCI Express Dual Port Multifunction Gigabit Server Adapter User Guide
- 2 Notice
- 3 Contents
- 4 Technician notes
- 5 Where to go for additional help
- 5 HP contact information
- 6 Introduction
- 6 Overview
- 7 LED indicators
- 8 UTP CAT5 cable
- 9 Installing an adapter
- 9 Installation overview
- 9 Preventing electrostatic discharge
- 10 Installing an adapter in a server
- 10 Connecting the network cable
- 11 Specifications
- 11 HP NC380T PCI Express Dual Port Multifunction Gigabit Server Adapter specifications
- 11 UTP cable specifications
- 12 RJ-45 pinouts and crossover function
- 12 10/100 pinouts using internal, straight-through crossover
- 13 10/100 pinouts using external crossover through twisted-pair media
- 14 Gigabit over copper pinouts using internal crossover for RJ-45
- 15 Gigabit over copper pinouts using external crossover through twisted pair media
- 17 Regulatory compliance notices
- 17 Regulatory compliance identification numbers
- 17 Federal Communications Commission notice
- 17 Class A equipment
- 18 Class B equipment
- 18 Declaration of conformity for products marked with the FCC logo, United States only
- 19 Modifications
- 19 Cables
- 19 Canadian notice (Avis Canadien)
- 19 European Union regulatory notice
- 20 Japanese notice
- 21 Korean class A notice
- 21 Korean class B notice
- 21 BSMI notice
- 21 Disposal of waste equipment by users in private households in the European Union
- 22 Electrostatic discharge
- 22 Overview
- 22 Grounding methods to prevent electrostatic discharge
- 23 Acronyms and abbreviations
- 25 Index