- Computers & electronics
- Audio & home theatre
- AV equipment stands
- Gladiator
- GAJG36FDZW
- Assembly Instructions
Install Doors. Gladiator GAJG36GRESG, GAJG36GRDG, GAJG36FDZW, GALG36KDESG
Add to my manuals
20 Pages
advertisement
6
4.
Repeat steps 2 and 3.
NOTE: Make sure the magnet in the right of each long shelf edge is facing out.
3.
Insert the middle 4 screws through the door hinge into the cabinet and hand tighten.
P2
P1
P2
P5mr
A
P1
P5mr
P3
P1
A
P5mr
P5mr P3
P7
A. Magnet facing outward
Adjust the Shelves
1.
Lift up on the underside of the shelf until the shelf tabs are free of the cabinet slots.
2.
Tilt the shelf up to reposition it within the cabinet or to remove it from the cabinet.
Install Doors
F3c
Phillips-head screw (12)
IMPORTANT:
■ The door with the lock assembly (P7) should be installed on the right-hand side of the cabinet.
■ The door hinges are designed with keyhole slots at the top and bottom so the door will hang on the cabinet while you are fastening the screws.
1.
Start Phillips-head screws (F3c) in both the top and bottom holes on each side of the cabinet.
2.
Hang the right-hand side door (P7) from the top and bottom screws, and hand tighten.
A. Phillips-head screws
4.
Repeat steps 2 and 3 to attach the left-hand door (P6).
5.
Align the doors and completely tighten the door screws.
Complete Assembly
1.
Make sure there is a bolt or screw in each hole of the cabinet frame.
2.
Move the cabinet to its final location.
3.
Place a level on an inside shelf, and if necessary, level the cabinet by adjusting the height of the leveling legs. Turn to the left to raise or to the right to lower the leveling leg.
4.
If the doors are not aligned, loosen all the screws attaching the door hinge to the cabinet.
5.
Adjust door to the desired height, and fully tighten the screws.
ACCESSORIES
To order accessories, call 1-866-342-4089 and ask for the accessory part number listed below or contact your authorized Gladiator ®
GarageWorks dealer. In Canada, call 1-800-807-6777.
Mounting Bracket Kit - Allows the cabinet to be mounted on
Gladiator ® Garageworks GearWall ® panels or GearTrack ® channels.
Order Part # GABK362PSS
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 CABINET/LOCKER SAFETY
- 3 PARTS
- 4 ASSEMBLY INSTRUCTIONS
- 4 Cabinet Use Requirements
- 4 Unpack Cabinet Parts
- 4 Assemble Cabinet
- 4 Attach Back Panels
- 5 Install Leveling Legs
- 5 Install Shelves
- 6 Install Doors
- 6 Complete Assembly
- 6 ACCESSORIES
- 7 WARRANTY
- 8 SEGURIDAD DEL ARMARIO
- 9 PIEZAS
- 10 INSTRUCCIONES DE ENSAMBLAJE
- 10 Requisitos de uso del armario
- 10 Desempaque las piezas del armario
- 10 Ensamble el armario
- 10 Fije los paneles posteriores
- 11 Instalación de las patas niveladoras
- 11 Instalación de los estantes
- 12 Instalación de las puertas
- 12 Complete el ensamblaje
- 13 ACCESORIOS
- 13 GARANTÍA
- 14 SÉCURITÉ DE L’ARMOIRE
- 15 PIÈCES
- 16 INSTRUCTIONS D’ASSEMBLAGE
- 16 Déballage des pièces de l’armoire
- 16 Assemblage de l’armoire
- 16 Fixation des panneaux arrière
- 17 de l’aplomb
- 17 Installation des étagères
- 18 Installation des portes
- 18 Fin de l’assemblage
- 19 ACCESSOIRES
- 19 GARANTIE