advertisement
iK81 / iK42 USER GUIDE
Utility Pages
Screen Contrast
The Screen page in the “UTILITY” section adjusts the contrast (and optimal viewing angle) of the screen from 0‐100% in 1% increments.
Stereo Linking
Stereo linking is available between DSP Drive Modules A & B and between C & D. Changing a parameter in either of the stereo linked Drive Modules will change the other linked Drive Module. Stereo linking is controlled by the STEREO page in the “UTILITY” menu.
Note: Stereo linking will only work when the linked Drive Modules are of equal size. Note: Stereo Linking state is not stored in
Presets (but is stored in Snapshots)
Current Ethernet IP Address
This may be viewed in the “IP Curr” page of the “UTILITY” menu. This value cannot be edited.
IP Mode
The Ethernet IP address may be automatic “Auto” or may be a fixed static value “Static” as determined by the “IP Mode” page of the “UTILITY” menu.
WARNING – Do NOT use Static mode unless your IT system specifically requires it. Auto mode should always be used where possible since in this mode, the Device can always be ‘discovered’ by the Vu‐Net application. When in Static mode, the IP
Address will flash on the Home screen.
See also Ethernet Configurations.
IP Static
This allows the Static Ethernet IP address to be adjusted by the rotary encoders on the IP Static page of the “UTILITY” menu. This page will only be visible when in Static mode.
Store Snapshot
This page of the “UTILITY” menu allows a Snapshot of the device to be stored.
See also Snapshots.
Recall Snapshot
This page of the “UTILITY” menu allows a Snapshot to be recalled.
See also Snapshots and Aux Port.
Bandwidth Units
This page of the “UTILITY” menu allows the Bandwidth of Parametric Equalisers to be viewed and adjusted in either Octaves or
‘Q’.
Aux Style
This page of the “UTILITY” menu allows the action of the Aux port to be viewed and adjusted.
See also Aux Port.
ECO
This page of the “UTILITY” menu allows the device to save power by going into a low power mode when it is not being used.
Standby is a fast mode which saves some energy, but will wake‐up very quickly if an audio input is detected. The associated
Standby Time parameter allows the amplifier to automatically go into power‐save if no audio signal has been detected for a period of time. This function can be defeated by setting the latter control to Manual. Linea would strongly advise leaving it set to automatic however as there is no negative consequence to doing this since ‘wake‐up’ on detecting the presence of an audio input signal is instantaneous.
iK81 / iK42 User Guide V1.0
31
advertisement
Related manuals
advertisement
Table of contents
- 2 Martin Audio iKon Amplifier User Guide
- 2 Contents
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 CONSIGNES DE SÉCURITÉ IMPORTANTES
- 6 AVERTISSEMENT DE SECURITE
- 7 COMPLIANCE
- 7 FOR CUSTOMERS IN EUROPE
- 7 FOR CUSTOMERS IN THE USA
- 8 FOR CUSTOMERS IN CANADA
- 8 Thanks and Unpacking
- 8 Unpacking the Martin Audio iK42/iK81 Series Amplifier
- 9 INSTALLATION INSTRUCTIONS
- 9 Mechanical Installation
- 10 AC Power Connection
- 11 The User Guide
- 12 Introduction and Key Features
- 12 Introduction
- 12 Key Features
- 14 Audio Connections
- 14 Input Connections
- 14 Using unbalanced connections
- 14 Amplifier Output Connections
- 16 Load Matching
- 17 Panel Layouts
- 20 Quick start
- 20 Loading XE500 (or XE300 Bi‐amp) Presets
- 21 Loading XE300 Passive Presets
- 23 Operation
- 23 Starting up the unit
- 23 Overview of Modules, Presets Components and Snapshots
- 24 Navigation
- 25 The Home Page
- 25 Drive Modules
- 25 Drive Module Presets
- 25 Component Presets
- 25 Factory Module Presets
- 26 Storing Module Presets
- 26 Recalling Module Presets
- 26 Recalling Components
- 27 Input
- 27 AES3 Inputs
- 27 Dante™ Inputs
- 27 Automatic Input Selection (Fallover)
- 27 Gain and Polarity
- 28 Delay
- 28 High Pass Filter
- 28 Parametric Equalisation
- 28 FIR Shelving EQ
- 28 Parametric Filters
- 28 Routing
- 29 Output
- 29 Gain and Polarity
- 29 Delay
- 29 High and Low pass Filters
- 29 LIR Crossover Filtering
- 29 Parametric Equalisation and All‐Pass Filters
- 29 Limiters
- 30 VX Limiter
- 30 Tmax Thermal Limiter
- 30 Xmax Excursion Limiter
- 30 Bridge
- 31 Routing
- 31 Driver
- 32 Utility Pages
- 32 Screen Contrast
- 32 Stereo Linking
- 32 Current Ethernet IP Address
- 32 IP Mode
- 32 IP Static
- 32 Store Snapshot
- 32 Recall Snapshot
- 32 Bandwidth Units
- 32 Aux Style
- 33 External Breaker Protection (EBP)
- 33 Ethernet
- 33 Ethernet configurations
- 33 AUTO‐IP
- 33 Static‐IP
- 33 IP Troubleshooting
- 34 Snapshots
- 34 AUX Port
- 35 Latency delay
- 36 Secure Mode
- 36 Overlay Flush
- 36 Revert to Factory Settings
- 36 Protection Systems
- 36 Summary of Protection Indication
- 37 Incident Reporting
- 37 Fault Relay
- 37 Performance Logging
- 38 Vu‐Net
- 39 Processing Block Diagram
- 40 Input Menu Map
- 41 Output Menu Map
- 42 Utility Menu Map
- 43 EQ and Filter Response Graphs
- 46 Technical Specifications
- 46 General
- 46 Audio
- 46 Digital processing
- 47 Power Output iK
- 47 Power supply
- 47 Protection systems
- 47 Power distribution protection systems
- 47 Monitoring and logging
- 48 Physical
- 48 Options