advertisement
How to Ride the Motorcycle
To Stop the Engine
1
3
2
1. Engine stop switch
2. Starter button
3. Neutral indicator light
4. ON position
5. Ignition switch
Close the throttle completely.
Select neutral.
Turn the ignition switch off.
Select first gear.
Support the motorcycle on a firm, level surface with the side stand.
Lock the steering.
Caution
The engine should normally be stopped by turning the ignition switch to the OFF position. The engine stop switch is for emergency use only. Do not leave the ignition switched on with the engine stopped. Electrical damage may result.
OFF
O
N
5
P
4
To Start the Engine
Check that the engine stop switch is in the
RUN position.
Ensure the transmission is in neutral.
Pull the clutch lever fully into the handlebar.
Turn the ignition switch on.
Note:
•
•
When the ignition is switched on, the tachometer needle will quickly sweep from zero to maximum and then return to zero. The instrument warning lights will illuminate and will then go off
(except those which normally remain on until the engine starts see page 37 . It is not necessary to wait for the needle to return to zero before starting the engine.
In very cold conditions, part open the throttle to aid cold starting.
Return it to the closed position once the engine has started.
56
advertisement
Related manuals
advertisement
Table of contents
- 20 Instrument Panel Layout
- 21 Speedometer and Odometer
- 21 Tachometer
- 21 Trip Computer
- 22 Odometer/Trip Meter
- 22 Trip Meter
- 23 Trip Meter Reset
- 23 Odometer
- 23 Clock Adjustment
- 24 Changing Units (Imperial, US or Metric)
- 26 ABS Disable (models with ABS only)
- 26 Service Interval Indicator
- 27 Gear Change Lights
- 27 Gear Change Light Modes
- 27 Setting Gear Change Light Limits
- 28 Changing the Set Speed
- 29 Setting Gear Change Lights to Off
- 30 Lap Timer
- 31 Data Recording Mode
- 31 New Lap Recording
- 32 Data Retrieval Mode
- 33 Coolant Temperature Gauge
- 34 Fuel Gauge
- 34 Tyre Pressure Monitoring System (TPMS)
- 34 Function
- 35 Tyre Pressure Sensor Serial Number
- 35 Front Sensor
- 35 Rear Sensor
- 35 System Display
- 36 Sensor Batteries
- 36 Tyre Pressures
- 36 Replacement Tyres
- 37 Warning Lights
- 37 Direction Indicators
- 37 High Beam
- 37 Low Fuel
- 37 Neutral
- 37 Low Oil Pressure Warning Light
- 37 High Coolant Temperature Warning Light
- 38 Engine Management System Malfunction Indicator Light
- 38 Alarm/Immobiliser Indicator Light
- 39 Tyre Pressure Warning Light
- 40 Ignition Key
- 41 Ignition Switch/Steering Lock
- 41 Engine Immobiliser
- 41 Ignition Switch Positions
- 42 Brake and Clutch Lever Adjusters
- 42 Clutch Lever
- 43 Brake Lever
- 43 Right Handlebar Switches
- 43 Engine Stop Switch
- 44 Starter Button
- 44 Left Handlebar Switches
- 44 Headlight Dip Switch
- 45 Direction Indicator Switch
- 45 Horn Button
- 45 Pass Button
- 45 Fuel Requirement/Refuelling
- 45 Fuel Grade
- 46 Fuel Tank Cap
- 47 Filling the Fuel Tank
- 48 Stand
- 48 Side Stand
- 48 Tool Kit and Handbook
- 49 Seat Lock
- 49 Seat Care
- 51 Running-In
- 52 Safe Operation
- 52 Daily Safety Checks
- 56 To Stop the Engine
- 56 To Start the Engine
- 57 Moving Off
- 58 Changing Gears
- 59 Braking
- 61 ABS (Anti-Lock Brake System) models only
- 62 Parking
- 63 Considerations for High-Speed Operation
- 64 General
- 64 Steering
- 64 Luggage
- 64 Brakes
- 64 Tyres
- 65 Engine Oil
- 65 Coolant
- 65 Electrical Equipment
- 65 Miscellaneous
- 74 Scheduled Maintenance
- 77 Engine Oil
- 78 Oil Level Inspection
- 79 Oil and Oil Filter Change
- 80 Disposal of Used Engine Oil and Oil Filters
- 80 Oil Specification and Grade
- 81 Cooling System
- 81 Corrosion Inhibitors
- 82 Coolant Level Inspection
- 82 Coolant Level Adjustment
- 83 Coolant Change
- 83 Radiator and Hoses
- 84 Fuel Tank
- 84 Raising
- 85 Lowering
- 85 Throttle Control
- 86 Inspection
- 88 Clutch
- 89 Inspection
- 89 Adjustment
- 89 Drive Chain
- 90 Chain Lubrication
- 90 Chain Free-Movement Inspection
- 91 Chain Free-Movement Adjustment
- 92 Chain and Sprocket Wear Inspection
- 93 Brakes
- 93 Brake Wear Inspection
- 93 Breaking-in New Brake Pads and Discs
- 94 Brake Pad Wear Compensation
- 94 Disc Brake Fluid
- 95 Brake Fluid Level Inspection and Adjustment
- 96 Brake Light Switches
- 96 Steering/Wheel Bearings
- 96 Steering Inspection
- 97 Inspecting the Steering (Headstock) Bearings for Free Play
- 97 Wheel Bearings Inspection
- 98 Front Suspension
- 98 Front Fork Inspection
- 99 Suspension Setting Chart - Speed Triple
- 99 Suspension Setting Chart - Speed Triple R
- 100 Front Suspension Settings
- 101 Rebound Damping Adjustment
- 102 Compression Damping Adjustment
- 103 Rear Suspension Adjustment
- 103 Rebound Damping Adjustment
- 104 Compression Damping Adjustment
- 106 Tyres
- 106 Tyre Inflation Pressures
- 107 Tyre Wear
- 107 Minimum Recommended Tread Depth
- 108 Tyre Replacement
- 111 Battery
- 111 Battery Removal
- 112 Battery Disposal
- 112 Battery Maintenance
- 112 Battery Discharge
- 112 Battery Discharge During Storage and Infrequent Use of the Motorcycle
- 113 Battery Charging
- 113 Battery Installation
- 114 Fuse Boxes
- 114 Fuse Identification
- 116 Headlights
- 117 Headlight Bulb Replacement
- 119 Rear Light
- 119 Rear Light Replacement
- 119 Direction Indicator Lights
- 119 Bulb Replacement
- 120 Licence Plate Light
- 120 Bulb Replacement
- 121 Cleaning
- 121 Preparation for Washing
- 121 Where to be Careful
- 122 After Washing
- 122 Seat Care
- 122 Unpainted Aluminium Items
- 123 Cleaning of the Exhaust System
- 123 Washing
- 123 Drying
- 123 Protecting