advertisement
www.seagate.com
SATA Interface
82
H
86
H
90
H
AA
H
F1
H
06
H
07
H
10
H
55
H
4.3.2 Set Features command
This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the Features register are defined as follows:
Table 14 Set Features commands
02
H
Enable write cache (default).
03
H
Set transfer mode (based on value in Sector Count register).
Sector Count register values:
00
H
Set PIO mode to default (PIO mode 2).
01
H
Set PIO mode to default and disable IORDY (PIO mode 2).
08
H
PIO mode 0
09
H
PIO mode 1
0A
H
PIO mode 2
0B
H
PIO mode 3
0C
H
PIO mode 4 (default)
20
H
Multiword DMA mode 0
21
H
Multiword DMA mode 1
22
H
Multiword DMA mode 2
40
H
Ultra DMA mode 0
41
H
Ultra DMA mode 1
42
H
Ultra DMA mode 2
43
H
Ultra DMA mode 3
44
H
Ultra DMA mode 4
45
H
Ultra DMA mode 5
46
H
Ultra DMA mode 6
Enable the PUIS feature set
PUIS feature set device spin-up
Enable use of SATA features
Disable read look-ahead (read cache) feature
Disable write cache
Disable the PUIS feature set
Disable use of SATA features
Enable read look-ahead (read cache) feature (default).
Report full capacity available
Note
At power-on, or after a hardware or software reset, the default values of the features are as indicated above.
Seagate SkyHawk Product Manual, Rev. L 38
advertisement
Related manuals
advertisement
Table of contents
- 6 Seagate® Technology Support Services
- 7 Introduction
- 8 About the SATA interface
- 9 Drive Specifications
- 9 Specification summary tables
- 13 Formatted capacity
- 13 LBA mode
- 13 Default logical geometry
- 13 Seek time
- 14 Start/stop times
- 14 Power specifications
- 14 Power consumption
- 16 Typical current profile
- 16 Conducted noise
- 16 Voltage tolerance
- 17 Power-management modes
- 17 Environmental specifications
- 17 Drive case temperature
- 17 Temperature
- 18 Temperature gradient
- 18 Humidity
- 18 Altitude
- 18 Shock
- 19 Vibration
- 19 Acoustics
- 19 Test for Prominent Discrete Tones (PDTs)
- 20 Electromagnetic immunity
- 20 Reliability - Mean Time Between Failure
- 20 Storage
- 20 Warranty
- 21 Agency and Safety Certifications
- 21 Safety certification
- 21 Electromagnetic compatibility
- 21 Electromagnetic compliance
- 22 European Union (EU) CE Marking Requirements
- 22 Australian RCM Compliance Mark
- 22 Canada ICES
- 22 South Korean KC Certification Mark
- 22 Morocco Commodity Mark
- 23 Taiwanese BSMI
- 23 FCC verification
- 23 Environmental protection
- 23 European Union Restriction of Hazardous Substance Law
- 23 Restriction of Hazardous Substances in Electrical and Electronic Equipment
- 24 China Requirements —China RoHS
- 25 Taiwan Requirements — Taiwan RoHS
- 25 Corrosive environment
- 26 Configuring and Mounting the Drive
- 26 Handling and static-discharge precautions
- 26 Configuring the drive
- 26 SATA cables and connectors
- 27 Drive mounting
- 32 SATA Interface
- 32 Hot-Plug compatibility
- 32 SATA device plug connector pin definitions
- 33 Supported ATA commands
- 35 Identify Device command
- 39 Set Features command
- 40 S.M.A.R.T. commands