advertisement
02
H
03
H
10
H
55
H
82
H
90
H
AA
H
F1
H
4.3.2
Set Features command
This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the Features register are defined as follows
Table 8 Set Features command values
Enable write cache (default).
Set transfer mode (based on value in Sector Count register).
Sector Count register values:
0A
H
0B
H
0C
H
20
H
21
H
22
H
00
H
01
H
08
H
09
H
Set PIO mode to default (PIO mode 2).
Set PIO mode to default and disable IORDY (PIO mode 2).
PIO mode 0
PIO mode 1
PIO mode 2
PIO mode 3
PIO mode 4 (default)
Multiword DMA mode 0
Multiword DMA mode 1
Multiword DMA mode 2
40
H
41
H
42
H
Ultra DMA mode 0
Ultra DMA mode 1
Ultra DMA mode 2
43
H
44
H
Ultra DMA mode 3
Ultra DMA mode 4
45
H
46
H
Ultra DMA mode 5
Ultra DMA mode 6
Enable use of SATA features
Disable read look-ahead (read cache) feature.
Disable write cache
Disable use of SATA features
Enable read look-ahead (read cache) feature (default).
Report full capacity available
Note At power-on, or after a hardware or software reset, the default values of the features are as indicated above.
Seagate IronWolf Serial ATA Product Manual, Rev. B 28
advertisement
Key Features
- 10 TB 3.5" 7200 RPM Serial ATA III
- NAS HDD
- Storage drive buffer size: 256 MB
- 6 Gbit/s
- 705 g
Related manuals
advertisement
Table of contents
- 5 Seagate® Technology Support Services
- 6 Introduction
- 6 About the Serial ATA interface
- 7 Drive specifications
- 7 Specification summary tables
- 9 Formatted capacity
- 9 LBA mode
- 9 Recording and interface technology
- 9 Start/stop times
- 10 Power specifications
- 10 Power consumption
- 11 Conducted noise
- 11 Voltage tolerance
- 12 Extended Power Conditions - PowerChoiceTM
- 14 Environmental limits
- 14 Temperature
- 14 Humidity
- 14 Effective Altitude (sea level)
- 15 Shock
- 15 Vibration
- 16 Acoustics
- 16 Test for Prominent Discrete Tones (PDTs)
- 16 Electromagnetic immunity
- 17 Reliability
- 17 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)
- 17 Storage
- 17 Warranty
- 17 Agency certification
- 17 Safety certification
- 18 Electromagnetic compatibility
- 18 FCC verification
- 19 Environmental protection
- 19 European Union Restriction of Hazardous Substances (RoHS) Directive
- 19 China Requirements — China RoHS
- 20 Corrosive environment
- 20 Shipping, Repair and Returns
- 21 Configuring and mounting the drive
- 21 Handling and static-discharge precautions
- 21 Configuring the drive
- 21 Serial ATA cables and connectors
- 22 Drive mounting
- 22 Mechanical specifications
- 23 Serial ATA (SATA) interface
- 23 Hot-Plug compatibility
- 23 Serial ATA device plug connector pin definitions
- 24 Supported ATA commands
- 26 Identify Device command
- 29 Set Features command
- 30 S.M.A.R.T. commands