Strobe effect. EuroLite DMX OPERATOR 1610
Add to My manuals20 Pages
EuroLite DMX OPERATOR 1610 gives you full control over your lightshow, allowing you to create dynamic effects for any occasion. With 160 channels across 16 devices, you can effortlessly manage complex lighting setups. Store and recall up to 16 scenes and 16 chases with 200 scenes each, giving you a vast array of lighting options at your fingertips.
advertisement
Sound-controlled mode
In sound-control mode, the scenes stored in a memory bank will be synchronized with music pulses via the internal microphone.
1.
Switch to sound-controlled mode with the RUN MODE button.
2.
Call the desired chase with the CHASE buttons.
3.
The sensitivity of the sound control is adjustable between 0-100 % with the buttons ⊳ and .
4.
Use the FADE TIME control to adjust the fade time.
Strobe effect
By keeping the STROBE button (17) pressed you activate the strobe effect. The green LED lights up. Strobe can be used in all modes and means that the fixtures start to flash. You can adjust the speed with the fader (9).
Blackout
The BLACKOUT button (16) remains active in each mode. If you press (16) all fixtures go out (standby mode).
The LED of the button flashes. You can go back to the previous state by pressing the Blackout button again.
Data backup
All settings of a light show, i.e. DMX settings, scenes and chases can be stored on a USB memory device and recalled later. 16 memory banks on the buttons FIXTURE 1-16 are available.
1.
Connect a USB memory device to the controller’s USB port.
2.
Keep the button RUN MODE pressed and simultaneously press the button ⊳ . The display indicates “ Save “.
3.
Select a memory bank with one of the FIXTURE buttons.
Each memory bank must be stored separately. If the control LED of a FIXTURE button lights, this memory bank has been stored on the USB memory device before.
The data will be stored in the folder “ led_operator “ located on the root directory of the USB memory device. A file with the extension “PRO” will be created for each memory bank. You should not make any changes to the default folder. Otherwise the controller cannot the reload the data later.
4.
After completing the data backup (approx. 20 seconds), the display shortly inserts “ ok “.
5.
Turn the controller off and on again. The data backup procedure is complete.
Data import
1.
Connect a USB memory device to the controller’s USB port.
2.
The files to be imported must be stored in the folder “ led_operator “ located on the root directory of the USB memory device.
3.
Keep the button RUN MODE pressed and simultaneously press the button . The display indicates “ Load “.
The control LED of a FIXTURE button lights, when data is available on the USB memory device for this memory bank.
4.
Select the file to be loaded with the FIXTURE buttons.
5.
After successful completion of the data import, the display shortly inserts “ ok ”.
6.
Turn the controller off and on again. The data import procedure is complete.
18 • EN
advertisement
Related manuals
advertisement
Table of contents
- 3 EINFÜHRUNG
- 3 Produktmerkmale
- 4 WICHTIGE SICHERHEITSHINWEISE
- 5 BEDIENELEMENTE UND ANSCHLÜSSE
- 6 INBETRIEBNAHME
- 6 DMX512-Anschluss
- 6 Stromversorgung herstellen
- 7 BEDIENUNG
- 7 Programmiermodus aktivieren
- 7 Szenen programmieren
- 7 Lauflicht (Chase) programmieren
- 8 Lauflicht aufrufen
- 9 Strobe-Effekt
- 9 Blackout (Dunkelschaltung)
- 9 Datensicherung
- 9 Daten laden
- 10 Firmware aktualisieren
- 10 Zurücksetzen auf Werkseinstellungen
- 10 REINIGUNG UND WARTUNG
- 10 TECHNISCHE DATEN
- 12 INTRODUCTION
- 12 Product features
- 13 IMPORTANT SAFETY INSTRUCTIONS
- 15 SETUP
- 15 DMX512 connection
- 15 Power supply
- 16 OPERATION
- 16 Enabling programming mode
- 16 Programming scenes
- 16 Programming chases
- 17 Playing chases
- 18 Strobe effect
- 18 Blackout
- 18 Data backup
- 18 Data import
- 19 Firmware update
- 19 Reset to factory settings
- 19 CLEANING AND MAINTENANCE
- 19 TECHNICAL SPECIFICATIONS