advertisement
C Speakers Connection
Front Speakers
Connect the speaker wires to the SPEAKERS
(FRONT) terminals, right speaker to " R " and left speaker to " L ", coloured (marked) wire to " + " and black (unmarked) wire to " ".
1 2
●
Fully insert the stripped portion of the speaker wire into the terminal as shown.
Rear Surround Speakers
Connect the speaker wires to the REAR
SURROUND terminals, right speaker to " R " and left speaker to " L ", coloured (marked) wire to " + " and black (unmarked) wire to " ".
Notes:
– For optimal sound performance, use the supplied speakers.
– Do not connect more than one speaker to any one pair of
+
/
-
speaker terminals.
– Do not connect speakers with an impedance lower than the speakers supplied. Please refer to the SPECIFICATIONS section of this manual.
D Video Out Connection
Connect the VIDEO OUT (CVBS) terminal at the rear of the system to the TV or VCR
VIDEO IN for viewing or recording.
Note:
– To avoid magnetic interference with the picture on your TV, do not position the front speakers too close to the TV.
Preparations
E Connecting other equipment to your system
Connect the audio left and right OUT terminals of a TV, VCR, Laser Disc player, DVD player or
CD Recorder to the AUX/CDR IN terminals.
Note:
– If you are connecting equipment with a mono output (a single audio out terminal), connect it to the AUX/CDR IN left terminal. Alternatively, you can use a “single to double” cinch cable (still be mono sound).
Inserting batteries into the
Remote Control
Insert two batteries (Type R06 or AA) into the remote control with the correct polarity as indicated by the + and symbols inside the battery compartment.
CAUTION!
– Remove batteries if they are exhausted or not to be used for a long time.
– Do not use old and new or different types of batteries in combination.
– Batteries contain chemical substances, so they should be disposed off properly.
9
3140 115 30491
Controls
(main system’s illustration on page 3)
Notes for remote control:
– First, select the source you wish to control by pressing one of the source select keys on the remote control (VCD 123 or
TUNER, for example).
– Then select the desired function (
É
,
í
,
ë
, for example).
Controls on the system and remote control
1 STANDBY ON y
– to switch the system on or to Standby mode.
2 DISPLAY SCREEN
– to view the current status of the system.
3 DISC TRAYS
4 DISC CHANGE
– to change disc(s).
5 DISC 1 / DISC 2 / DISC 3
– to select a disc tray for playback.
6 OPEN•CLOSE
– to open or close the disc tray.
7 INTERACTIVE VU METER
– to show the VU (volume unit) meter in music or volume mode depending on the display mode selected.
8 VOLUME
– to increase or decrease the volume.
9 Tape Deck Operation
AUTO REPLAY
– to select continuous playback in either AUTO
PLAY or ONCE mode only.
DUBBING
– to dub a tape.
REC
– to start recording on tape deck 2.
0 SOUND NAVIGATION
– to select the desired sound feature : DSC, VAC, or DBB.
!
JOG CONTROL
– to select the desired sound effect for the selected sound feature.
DSC ..................
DIGITAL, ROCK, POP, NEWAGE,
CLASSIC or ELECTRIC.
VAC ..................
HALL, CONCERT, CINEMA,
DISCO, ARCADE or CYBER.
DBB ..................
BEAT, PUNCH or BLAST.
@ INCREDIBLE SURROUND (IS)
– to activate or deactivate the surround sound effect.
# MAX SOUND (MAX)
– to activate or deactivate the optimal mix of various sound features.
10
3140 115 30491
$ MIC/LEVEL
– to connect microphone jack.
– to adjust the mixing level for karaoke or microphone recording.
% ç
– to open the tape deck door.
^ TAPE DECK 2
& TAPE DECK 1
* SOURCE – to select the following:
VCD PAL/NTSC / (CD 1•2•3)
– to select disc tray 1, 2 or 3 (this system can playback normal CD/VCD/MP3-CD format disc).
– (on the system only) to select corresponding video output for NTSC or PAL system of your
TV set (except Multi-system TV).
TUNER / (BAND)
– to select waveband : FM or MW.
TAPE / (TAPE 1• 2)
– to select tape deck 1 or 2.
AUX / (CDR/DVD)
– to select a connected external source :
CDR/DVD or AUX (auxiliary) mode.
( Mode Selection
PLAY PAUSE ÉÅ for CD/VCD/MP3-CD…to start or interrupt playback.
for TAPE .............. to start playback.
for PLUG & PLAY… (on the system only) to initiate and start plug & play mode .
SEARCH• TUNING à á
(ALBUM / + ) for MP3-CD only…to select previous/next
Album for VCD only…to move the zoomed picture to the left or right.
for CD/VCD .... to search backward/forward.
for TUNER ........ to tune to a lower or higher radio frequency.
for TAPE .............. to rewind or fast forward.
for CLOCK .......
(on the system only) to set the hour.
Controls
DEMO STOP/CLEAR Ç for CD/VCD/MP3-CD…to stop playback or to clear a programme.
for TUNER ........
(on the system only) to stop programming.
.................................
(on the system only) to delete the preset radio station.
for TAPE .............. to stop playback or recording.
................................. to reset tape counter number.
for DEMO .........
(on the system only) to activate/ deactivate the demonstration.
for CLOCK .......
(on the system only) to exit clock setting or cancel timer .
for PLUG & PLAY… (on the system only) to exit plug & play mode .
PREV / PRESET / NEXT í ë
(TITLE / + ) for MP3-CD only…to select previous/next Title.
for VCD only…to move the zoomed picture down or up.
................................. to select next or previous
MENU or VCD track during playback (for VCD with PBC switched on) .
for CD/VCD .... to skip to the previous or next track.
for TUNER ........ to select a preset radio station.
for CLOCK .......
(on the system only) to set the minute.
) n
– to connect headphones.
¡ VCD Operation (for VCD version 2.0 only)
PBC (PLAYBACK CONTROL)
– to switch on or off PBC mode.
RETURN
– to return to the previous MENU level during playback (for VCD with PBC switched on).
™ TITLE/ALBUM NAME
– to display the title or album name for
MP3-CD.
£ DISPLAY
– to select different screen display mode :
24
NORMAL, MODE 1, MODE 2, or MODE 3.
PROG for CD/VCD/MP3-CD… to programme disc tracks.
for TUNER ........ to programme preset radio stations.
for CLOCK .......
(on the system only) to select 12or 24-hour clock mode.
11
3140 115 30491
Controls
25 CLOCK•TIMER
– to view the clock, set the clock or set the timer.
§ OSD (ON SCREEN DISPLAY)
– to switch on or off the on screen display on the
27
TV.
ZOOM
– to enlarge a still picture of the VCD on the TV screen.
• RESUME
– to continue playback again from where you have stopped (for VCD with PBC switched off).
ª KEY CONTROL (
I È i
)
– to change the VCD key tone level to suit your vocal range .
I
........................... to decrease the key tone level.
È
.............................. to restore the key tone level to original setting.
i
............................. to increase the key tone level.
º ECHO / +
– to adjust the VCD echo level for karaoke after inserted the microphone.
⁄ SLOW Ö
– to watch the VCD at a slower speed.
¤ VOCAL
– to fade out the original vocal from a Karaoke
VCD or to switch between mono or stereo mode during audio disc playback.
‹ A - B
– to playback a certain scene or passage of a CD/
VCD repeatedly.
› DIGEST
– to scan through a VCD or a specific track.
fi REPEAT
– to playback track/disc/programme repeatedly.
fl DIGIT 0 – 9
(numbers consisting more than two figures must be keyed in within 2 seconds.)
– to select a track number for CD/VCD/MP3-CD.
‡ B
– to switch the system to Standby mode.
12
3140 115 30491
advertisement
Related manuals
advertisement