Lamp / Replacing New Lamp. BOXLIGHT Boxlight ProjectoWrite2-W, Boxlight ProjectoWrite WX25N-S, ProjectoWrite2, ProjectoWrite WX25N-S, ProjectoWrite2-W, Seattle WX25N LCD x3, ProjectoWrite WX25N
Add to my manuals
100 Pages
advertisement
Maintenance of Projector
Lamp (Please click here if your projector is with high efficiency filter.)
1. If you want to replace new lamp, but the projector was just turned off, please let the projector cool down and unplug power cord at least 60 minutes.
2. If the projector is mounted in the ceiling, contact your dealer to replace the lamp.
Replacing New Lamp
1. Remove the lamp door.
2. Loosen 2 screws of the lamp holder. Take the handle on the top of the lamp, pull out the lamp straight off the projector.
3. Insert new lamp, lock the lamp door firmly with 2 screws.
4. Put the lamp door on.
5. Please reset the lamp timer after replacing lamp. (P.34)
53
Maintenance of Projector
WARNING
The projector uses a high-pressure mercury lamp.
The explosion of lamp with a loud bang or burn out could possibly cause injury or a fire.
When the bulb burts, it is possible for shards of glass to fly into the lamp housing; and for gas containing mercury to escapefrom the projector’s vent holes.
If the lamp has broken, do not check the inside of the projector. Please ventilate the room immediately.
Do not touch or bring your face close to the broken pieces since it might get into your eyes or mouth. In case of injury, seek medical advice immediately.
Disposal of a Lamp
Dispose of a lamp in accordance with the local recycling laws.
Do not put it to your trash.
Recycling Lamp’s laws of the USA, go to www.lamprecycle.org
.
Recycling Product’slaws of USA, go to www.eiae.org
.
Recycling Product’slaws of Canada, go to www.epsc.ca
.
For more information about recycling laws, please contact local government agency or dealer
CAUTION HOT
Before replacing the Lamp part, pay attention to the following items:
1.The Lamp is optional part. Contact the dealer for replacement lamp.
2. The lamp becomes very hot when in use. Turn the power off and disconnect the power cord.
3.Wait 1 Hour before replacing the lamp.
4.Do not use old lamp part.
54
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Contents
- 7 Safety Instructions
- 8 Safety Labels
- 9 Part Names
- 9 Projector
- 10 Control Panel
- 12 Setting Up
- 12 Arrangement
- 13 Power ON / OFF
- 14 Setting Up The Projector
- 15 Ceiling Mounted Installation Guide
- 16 Adjusting The Projector’s Elevation
- 17 How To Connect
- 19 Remote Control
- 22 Remote Control (Optional)
- 26 Menu Operation
- 26 How To Operate On-Screen Display
- 27 MENU (PC Mode)
- 27 Picture Menu (PC Mode)
- 28 Audio Menu (PC Mode)
- 29 Setting Menu (PC Mode)
- 30 MENU (Video Mode)
- 30 Picture Menu (Video Mode)
- 31 Audio Menu (Video Mode)
- 32 Setting Menu (Video Mode)
- 33 Advanced Menu
- 36 Presentation Menu
- 38 Security Menu
- 41 PIN Key In Operation
- 42 Network Control Software Application
- 43 Before Use
- 43 Before To Use Network Control Software
- 44 Projector Auto Search
- 46 Modify the Projector Setting
- 47 Delete
- 48 Projector Setting
- 50 System Setting / Monitor / Default Setting / Auto Detect Optimal Setting
- 52 Control Panel Window Introduction
- 52 Power Control / Input Source / Function Key
- 53 Function Key / Projector Status
- 54 Network Control Window Introduction
- 55 Maintenance Of Projector
- 55 Air Filter / Replacing the Air Filter
- 56 Lamp / Replacing New Lamp
- 58 Other Care / Cleaning the Lens
- 59 Troubleshooting
- 59 Indicator
- 60 Error For Machine Defects
- 62 List of Supported Monitor Displays