Error For Machine Defects. BOXLIGHT Boxlight ProjectoWrite2-W, Boxlight ProjectoWrite WX25N-S, ProjectoWrite2, ProjectoWrite WX25N-S, ProjectoWrite2-W, Seattle WX25N LCD x3, ProjectoWrite WX25N
Add to my manuals
100 Pages
advertisement
Troubleshooting
Error For Machine Defects
The following problems may be confused with a machine defect. Check and follow the table. If it couldn’t be improved, contact your dealer .
Symptom
Projector power does not turn on.
No image
Colors are pale
Abnormal brightness
& contrast
Video is blurred
Cause / Remedy
The power cord is disconnected.
Plug the power cord into an AC outlet.
Intending to turn on the projector again during the cool down mode.
Wait until the cool down mode has completed.
There is no lamp and/or lamp cover is not firmly closed.
Please turn off the power and disconnect the power plug from the power outlet. Check if the lamp is installed or the lamp cover is firmly closed and turn on the power again.
Power cord has impaired.
When you touch the power cord, the indicator goes on then off, please remove the power cord and connect it again. If the situation is repeated, remove the power cord and contact your dealer.
The input is not connected correctly.
Select the appropriate input source.
No signal input.
Connect correctly.
The lens cover is attached to the lens.
Remove the lens cover.
Color density and color matching are not adjusted correctly.
Adjust the RGB setting.
Color lose.
Caused by poor VGA cable connection.
Brightness and contrast are not adjusted correctly.
Adjust the brightness and contrast setting.
The lamp is near the end of its service life.
Replace with a new lamp.
The projection lens is not focused.
Adjust the focus using the focus ring.
The lens is dirty or misty.
Clean the lens.
57
Troubleshooting
Error For Machine Defects
Symptom
No audio
Remote control is not working.
Cause / Remedy
The projector is not connected correctly.
Check audio cable if connect correctly.
The volume is set to minimum.
Adjust the volume.
Mute is turned on.
Press the MUTE button.
No battery.
Before using the remote control, please check the battery of remote control.
Remote signal is obstructed.
Remove the obstacle between projector and remote control.
58
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Contents
- 7 Safety Instructions
- 8 Safety Labels
- 9 Part Names
- 9 Projector
- 10 Control Panel
- 12 Setting Up
- 12 Arrangement
- 13 Power ON / OFF
- 14 Setting Up The Projector
- 15 Ceiling Mounted Installation Guide
- 16 Adjusting The Projector’s Elevation
- 17 How To Connect
- 19 Remote Control
- 22 Remote Control (Optional)
- 26 Menu Operation
- 26 How To Operate On-Screen Display
- 27 MENU (PC Mode)
- 27 Picture Menu (PC Mode)
- 28 Audio Menu (PC Mode)
- 29 Setting Menu (PC Mode)
- 30 MENU (Video Mode)
- 30 Picture Menu (Video Mode)
- 31 Audio Menu (Video Mode)
- 32 Setting Menu (Video Mode)
- 33 Advanced Menu
- 36 Presentation Menu
- 38 Security Menu
- 41 PIN Key In Operation
- 42 Network Control Software Application
- 43 Before Use
- 43 Before To Use Network Control Software
- 44 Projector Auto Search
- 46 Modify the Projector Setting
- 47 Delete
- 48 Projector Setting
- 50 System Setting / Monitor / Default Setting / Auto Detect Optimal Setting
- 52 Control Panel Window Introduction
- 52 Power Control / Input Source / Function Key
- 53 Function Key / Projector Status
- 54 Network Control Window Introduction
- 55 Maintenance Of Projector
- 55 Air Filter / Replacing the Air Filter
- 56 Lamp / Replacing New Lamp
- 58 Other Care / Cleaning the Lens
- 59 Troubleshooting
- 59 Indicator
- 60 Error For Machine Defects
- 62 List of Supported Monitor Displays