Parking Stand. Land Pride RTR1558, RTR1566, RTR1574, RTR1050, RTR1058, RTR1042, RTR1550
Add to my manuals
38 Pages
advertisement
Land Pride
Section 1: Assembly & Set-Up
Table of Contents
Parking Stand
Refer to Figure 1-1 on page 10:
!
CAUTION
To avoid bodily injury caused by accidental falling of tiller, stabilize unit with parking stand and support blocks!
1.
Insert parking stand (#10) into parking stand holder on the end of the tiller frame.
2.
Adjust parking stand to a height that will support the tiller level while resting on skid shoes.
3.
Secure parking stand with wire retaining pin (#11).
Make sure wire retainer is hooked over the end of the retaining pin.
3-Point Hitch Assembly
Refer to Figure 1-1 on page 10:
1.
Install both top 3-point hitch plates (#1 and #2) to outside of gearbox mounting frame with 5/8" x 1 3/4" long bolts (#3), 5/8" lockwashers (#4), and 5/8" nuts
(#5). Do not tighten hardware at this time.
2.
Install spacer (#6) between upper 3-point hitch plates (#1 & #2) with 3/4" x 4" long bolt (#7), 3/4" lockwasher (#8), and 3/4" nut (#9).
3.
Securely tighten all bolts. Refer to the Torque Values
Chart in the “Appendix” section on page 33.
4.
Mount left hand clevis (#13) over the square tube as shown. Make certain the longer chamfer is positioned on the bottom.
5.
Locate u-bolt (#16) behind the square tube and insert through clevis (#13) holes as shown.
6.
Secure with 1/2" hex locknuts (#14). Do Not
Tighten.
7.
Repeat steps 4 through 6 for the right hand clevis.
8.
Position clevises 26 7/8" apart from inside of clevis plate to inside of clevis plate and center off the gearbox input shaft as shown.
9.
Tighten 1/2" locknuts (#14) to the correct torque.
Refer to the Torque Values Chart in the “Appendix” section on page 33.
10. Attach manual storage tube (#17) to hitch plate (#2) with 1/2"-20 x 1 1/4" GR5 cap screws (#18), flat washers (#19), and nylock hex nuts (#20). Tighten nuts to the correct torque.
Front Deflector
Refer to Figure 1-2:
1.
Remove 3/8" x 1 1/2" bolts (#1), washers (#2), lockwashers (#6), hex nuts (#7), and front deflector mounting bars (#3 & #5) from the tiller frame.
2.
Insert 3/8" x 1 1/2" hex bolts (#1) through 3/8" flat washers (#2), upper front deflector mount bar (#3), front rubber deflector (#4), and mounting holes “A”.
3.
Secure to tiller with lower front deflector mount bar
(#5), 3/8" lock washers (#6), and 3/8" hex nuts (#7).
4.
Securely tighten all bolts. Refer to the Torque Values
Chart in the “Appendix” section on page 33.
11/01/11
Figure 1-2
22253
RTR10 & RTR15 Series Rotary Tillers 311-431M 11
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Important Safety Information
- 3 Safety at All Times
- 3 Look For The Safety Alert Symbol
- 6 Safety Labels
- 11 Introduction
- 11 Application
- 11 Using This Manual
- 11 Terminology
- 11 Definitions
- 11 Owner Assistance
- 11 Serial Number
- 11 Further Assistance
- 12 Section 1: Assembly & Set-Up
- 12 Dealer Preparations
- 12 Tractor Requirements
- 12 Torque Requirements
- 13 Parking Stand
- 13 3-Point Hitch Assembly
- 13 Front Deflector
- 14 Rear Deflector Assembly
- 14 Tractor Hook-Up
- 15 Driveline Installation
- 16 Check Driveline Collapsible Length
- 16 Shorten Driveline
- 17 Check Driveline Maximum Length
- 17 Check Driveline Interference
- 18 Section 2: Operating
- 18 Operating Checklist
- 18 Inspections
- 18 Safety Information
- 19 Transporting
- 20 Parking
- 20 General Operating Notes
- 21 General Operating Instructions
- 22 Section 3: Adjustments
- 22 RTR10 Tiller Hitch Offset
- 22 RTR15 Tiller Hitch Sideshift
- 23 Drive Chain
- 23 Rear Deflector
- 24 Skid Shoe Adjustment
- 25 Section 4: Maintenance & Lubrication
- 25 Maintenance
- 25 Tine Replacement
- 25 Driveline Protection
- 25 Clutches With 4 Adjusting Nuts
- 25 Clutch Run-In
- 26 Clutch Disassembly & Assembly
- 27 Clutches With 8 Hex Socket Bolts
- 27 Clutch Run-In
- 27 Clutch Disassembly & Assembly
- 27 Shearbolt Protection
- 28 Storage
- 28 Lubrication
- 28 Driveline U-Joint
- 28 Driveline Shaft
- 29 Chaincase
- 29 Bearing On Right End Of Rotor Shaft
- 29 Gearbox
- 30 Section 5: Specifications & Capacities
- 30 RTR10 Series Rotary Tiller
- 31 RTR15 Series Rotary Tiller
- 32 Section 6: Features & Benefits
- 32 RTR10 Series Rotary Tiller
- 33 RTR15 Series Rotary Tiller
- 34 Section 7: Troubleshooting
- 35 Section 8: Torque Values Chart
- 37 Section 9: Warranty