Clutch Disassembly & Assembly. Land Pride RTR1558, RTR1566, RTR1574, RTR1050, RTR1058, RTR1042, RTR1550
Add to my manuals
38 Pages
advertisement
Table of Contents
Section 4: Maintenance & Lubrication
Clutch Disassembly & Assembly
If clutch run-in procedure indicates that one or more of the friction disks did not slip, then the clutch must be disassembled to separate the friction disks.
IMPORTANT: Before proceeding, secure clutch firmly in a clamping device to prevent injury.
2-Plate Disassembly
Step 1
Remove snap ring.
2-Plate Assembly
Step 1
Place hub and friction disks into the housing.
Step 2
Compress Belleville Springs to the pressure plate by tightening the four hex nuts and then placing the assembly into the clutch housing.
Step 2
Remove backup ring, lock collar, compression spring, bottom backup ring, and balls.
Step 3
Tighten the four hex nuts uniformly until the clutch pack and hub are loose.
Step 3
Bend retaining lugs inward over the
Belleville Spring edges to secure the spring before backing the four hex nuts off.
Step 4
With lugs bent in, loosen the four hex nuts completely to the end of the threaded studs.
Step 4
Bend all four retaining lugs out on edge of clutch housing.
Step 5
Insert greased balls.
Step 5
Remove thrust plate with Belleville
Springs and lug rings to access friction disks and hub for inspection or service.
Step 6
Install bottom backup ring, compression spring, lock collar, and top backup ring.
Step 6
Inspect friction disks and hub.
10435
24 RTR10 & RTR15 Series Rotary Tillers 311-431M
10449
Step 7
Install snap ring.
11/01/11
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Important Safety Information
- 3 Safety at All Times
- 3 Look For The Safety Alert Symbol
- 6 Safety Labels
- 11 Introduction
- 11 Application
- 11 Using This Manual
- 11 Terminology
- 11 Definitions
- 11 Owner Assistance
- 11 Serial Number
- 11 Further Assistance
- 12 Section 1: Assembly & Set-Up
- 12 Dealer Preparations
- 12 Tractor Requirements
- 12 Torque Requirements
- 13 Parking Stand
- 13 3-Point Hitch Assembly
- 13 Front Deflector
- 14 Rear Deflector Assembly
- 14 Tractor Hook-Up
- 15 Driveline Installation
- 16 Check Driveline Collapsible Length
- 16 Shorten Driveline
- 17 Check Driveline Maximum Length
- 17 Check Driveline Interference
- 18 Section 2: Operating
- 18 Operating Checklist
- 18 Inspections
- 18 Safety Information
- 19 Transporting
- 20 Parking
- 20 General Operating Notes
- 21 General Operating Instructions
- 22 Section 3: Adjustments
- 22 RTR10 Tiller Hitch Offset
- 22 RTR15 Tiller Hitch Sideshift
- 23 Drive Chain
- 23 Rear Deflector
- 24 Skid Shoe Adjustment
- 25 Section 4: Maintenance & Lubrication
- 25 Maintenance
- 25 Tine Replacement
- 25 Driveline Protection
- 25 Clutches With 4 Adjusting Nuts
- 25 Clutch Run-In
- 26 Clutch Disassembly & Assembly
- 27 Clutches With 8 Hex Socket Bolts
- 27 Clutch Run-In
- 27 Clutch Disassembly & Assembly
- 27 Shearbolt Protection
- 28 Storage
- 28 Lubrication
- 28 Driveline U-Joint
- 28 Driveline Shaft
- 29 Chaincase
- 29 Bearing On Right End Of Rotor Shaft
- 29 Gearbox
- 30 Section 5: Specifications & Capacities
- 30 RTR10 Series Rotary Tiller
- 31 RTR15 Series Rotary Tiller
- 32 Section 6: Features & Benefits
- 32 RTR10 Series Rotary Tiller
- 33 RTR15 Series Rotary Tiller
- 34 Section 7: Troubleshooting
- 35 Section 8: Torque Values Chart
- 37 Section 9: Warranty