- Vehicles & accessories
- Motor vehicle electronics
- Car audio amplifiers
- Delta Tau
- PMAC2
- Owner's manual
advertisement
▼
Scroll to page 2
of 34
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 INTRODUCTION
- 5 Overview
- 5 Board Configuration
- 5 Base Version
- 5 Option 2: Dual-Ported RAM
- 5 Option 3: USB1.1 Communications Port
- 6 Option 5: CPU and Memory Configurations
- 6 Option 6: Extended Servo Algorithm
- 6 Option 6L: Multi-block Lookahead Firmware
- 6 Option 7: Plate Mounting
- 6 Option 8A: High-Accuracy Clock Crystal
- 6 Option 10: Firmware Version Specification
- 6 Option 12: Analog-to-Digital Converters
- 7 Option 16: Battery-Backed Parameter Memory
- 8 HARDWARE SETUP
- 8 Watchdog Timer Jumper
- 8 CPU Frequency Control Jumpers
- 8 Re-Initialization Jumper
- 8 Power-Up State Jumpers
- 8 Firmware Load Jumper
- 8 Flash Memory Bank Select Jumpers
- 8 Encoder Sample Clock Source Jumpers
- 9 Serial Port Selection Jumper
- 9 Output Disable State Jumpers
- 9 Amplifier Enable / EQU Jumper
- 10 Resistor Pack Configuration
- 10 Termination Resistors
- 10 Pull-Up/Pull-Down Resistors
- 11 Connections
- 11 Mounting
- 11 Power Supply Connection
- 11 Machine Port Connections
- 11 Display Port
- 12 Multiplexer Port
- 12 I/O Port
- 12 Serial Ports
- 12 A/D-Converter Port
- 12 Handwheel Port
- 13 COMMUNICATIONS SETUP
- 15 FLEX CPU BOARD JUMPER DESCRIPTIONS
- 16 E1: Watchdog Disable Jumper
- 16 E2: Dual-Ported Ram Port Select
- 16 E4 – E6: Power-Up/Reset Load Source
- 16 E7: Firmware Reload Enable
- 16 E10A, B, C: Flash Memory Bank Select
- 17 JUMPER DESCRIPTIONS
- 17 E2: CPU Frequency Select
- 17 E3: Normal/Re-Initializing Power-Up/Reset
- 17 E4: CPU Frequency Select
- 17 E5 – E6: (Reserved for Future Use)
- 18 E13 - E14: Encoder Sample Clock Direction Control
- 18 E17 - E18: Serial Port Type Selection
- 19 E111-118: Command Output Disable State
- 20 MATING CONNECTORS
- 20 CPU Board Connectors
- 20 J2 (JEXP)/Expansion
- 20 Baseboard Connectors
- 20 J1 (JANA)/Analog (Option 12)
- 20 J2 (JTHW)/Multiplexer Port
- 20 J3 (JIO)/Digital I/O
- 20 J5 (JRS232)/RS-232 Serial Communications
- 20 J5A (JRS422)/RS-422 Serial Communications
- 20 J6 (JDISP)/Display
- 20 J7 (JHW)/Auxiliary Channel
- 20 J8 (JEQU)/Position Compare
- 21 J9 (JMACH1)/Machine Port
- 21 J10 (JMACH2)/Machine Port
- 22 BASE BOARD CONNECTOR PINOUTS
- 22 J1 (JANA) Analog Input Port Connector
- 23 J2 (JTHW) Multiplexer Port Connector
- 24 J3 (JI/O) General Input/Output Connector
- 25 J5 (JRS232) Serial Port Connector
- 25 J5A (RS422) Serial Port Connector
- 25 JRS422 (26-PIN Connector)
- 26 J6 (JDISP) Display Connector
- 26 J7 (JHW) Handwheel Encoder Connector
- 27 J8 (JEQU) Position Compare Output Connector
- 27 J9 (JMACH1) Connector Description
- 27 J9 JMACH1 Connector
- 30 J10 (JMACH2) Connector Description
- 30 J10 JMACH2 Connector
- 34 TB1 (2/4-Pin Terminal Block)
- 34 TB2 (3-Pin Terminal Block)