advertisement
7. Installing the knife
WARNING :
To protect against possible personal injury due to abrupt start of the machine, be sure to start the following work after turning the power off and ascertaining that the motor is at rest.
w
When replacing the knife with a new one, perform as follows.
1) Knife q can be easily removed together with the washer when removing knife retaining screw w .
2) Adjust so that the knife, when lowered the knife bar by hand, is spaced 1 to 2 mm away from the top surface of the throat plate as illustrated in the sketch. Then, be sure to place the washer and tighten the knife retaining screw.
1 to 2 mm q
Inch → mm CONVERSION TABLE
Knife size
1/4
3/8
7/16
1/2
9/16
5/8
11/16
3/4
13/16
7/8
1
1 1/8
1 1/4
1 3/8
1 1/2
Indication of mm
6.40
9.50
11.10
12.70
14.30
15.90
17.50
19.10
20.60
22.20
25.40
28.60
31.80
34.90
38.10
When the cloth cutting knife you have is indicated in inch, set the cloth cutting length (knife size) in mm using the inch → mm conversion table. (See P.29.)
− 15 −
advertisement
Related manuals
advertisement
Table of contents
- 6 . IMPORTANT SAFETY INSTRUCTIONS
- 6 . SPECIFICATIONS
- 6 1. Subclass
- 6 2. Specifications
- 7 3. Standard sewing shape list
- 8 4. Configuration
- 9 . INSTALLATION
- 17 . PREPARATION BEFORE OPERATION
- 17 1. Lubrioation
- 17 2. Inserting the needle
- 18 3. Threading the needle-thread
- 18 4. Threading the bobbin case
- 19 5. Adjusting the bobbin thread tension
- 19 6. Installation of bobbin case
- 20 7. Installing the knife
- 21 . OPERATION OF THE SEWING MACHINE
- 21 1. Explanation of the operation panel switch
- 23 2. Basic operation of the sewing machine
- 23 3. How to use the pedal
- 25 4. Input of the presser type
- 26 5. Performing pattern selection
- 27 6. Changing needle thread tension
- 28 7. Performing re-sewing
- 29 8. Winding bobbin thread
- 30 9. Using the counter
- 31 10. Using the initial value pattern
- 32 11. Changing sewing data
- 33 12. Method of setting sewing data with/without edit
- 34 13. Sewing data list
- 40 14. Copying sewing pattern
- 41 15. Using pattern register key
- 42 16. Using parameter register key
- 43 17. Performing continuous stitching
- 45 18. Performing cycle stitching
- 47 19. Explanation of plural motions of knife
- 48 20. Method of changing memory switch data
- 49 21. Memory switch data list
- 53 . MAINTENANCE
- 53 1. Adjusting the needle-to-hook relation
- 54 2. Adjusting the needle thread trimmer
- 55 3. Adjusting the presser bar pressure
- 55 4. Adjustment of the bobbin presser unit
- 57 5. Thread tension
- 57 6. Cleaning the filter
- 57 7. Replacing the fuse
- 58 . GAUGE COMPONENTS
- 58 1. Cloth cutting knife
- 58 2. Throat plate
- 58 3. Presser
- 59 . ERROR CODE LIST
- 62 . TROUBLES AND CORRECTIVE MEASURES
- 64 . DRAWING OF THE TABLE
- 65 . INITIAL VALUE DATA FOR EACH SHAPE TABLE