- Home
- Domestic appliances
- Sewing & ironing
- Sewing machines
- Alliance Laundry Systems
- Stacked Clothes Dryer
- User manual
advertisement
Heat Source Check
Electric Dryers
Metered Models
Set the proper FABRIC SELECTOR switch at
NORMAL. Place coins in the slide and carefully push slide in as far as possible. IN USE light will come on indicating the dryer is ready to operate. Close the loading door and press the PUSH-TO-START button firmly to start the dryer. After either dryer has operated for three minutes, the exhaust air or exhaust pipe should be warm.
Nonmetered Models
Set FABRIC SELECTOR switch at NORMAL and turn timer knob to 50. Close the loading door and press the PUSH-TO-START button. IN USE light will come on indicating start of cycle. After either dryer has operated for three minutes, the exhaust air or exhaust pipe should be warm.
Gas Dryers
During the gas heat check, observe the burner flame.
The flame can be viewed by removing the lower front panel of the dryer.
Metered Models
Set FABRIC SELECTOR switch at NORMAL. Place coins in the slide and carefully push slide in as far as possible. IN USE light will come on indicating the dryer is ready to operate. Close the loading door and press the PUSH-TO-START button firmly. The dryer will start, the igniter will glow red and the main burner will ignite.
Installation
Nonmetered Models
Set FABRIC SELECTOR switch at NORMAL and turn timer knob to 50. Close the loading door and press the PUSH-TO-START button. IN USE light will come on indicating start of cycle, the igniter will glow red and the main burner will ignite.
IMPORTANT: If all air is not purged out of the gas line, the gas igniter may go off before the gas is ignited. If this happens, after approximately two minutes the igniter will again attempt gas ignition.
All Models
After either dryer has operated for approximately five minutes, observe burner flame. Adjust the air shutter to obtain a soft, uniform blue flame. (A lazy yellow-tipped flame indicates lack of air. A harsh, roaring, very blue flame indicates too much air.)
Adjust the air shutter as follows:
1. Loosen the air shutter lockscrew.
2. Turn the air shutter to the left to get a luminous yellow-tipped flame, then turn it back slowly to the right to obtain a steady soft blue flame.
3. After the air shutter is adjusted for proper flame, tighten the air shutter lockscrew securely.
4. Reinstall the lower front panel.
WARNING
For personal safety, lower front panel must be in place during normal operation.
W046
After either dryer has operated for approximately three minutes, the exhaust air or exhaust pipe should be warm.
510975 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Installation
1
6
5
3
4
1
2
Closed Position
Shut-Off Valve Handle
Air Shutter Lockscrew
Air Shutter
2
3
4
Figure 12
5
6
1/8" (3.1 mm) Pipe Plug
(For checking manifold pressure)
Open Position
D700I
20 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
510975
advertisement
Related manuals
advertisement
Table of contents
- 12 Nonmetered Models
- 13 Additional Security
- 13 Slide Extension
- 13 Timer Cams
- 14 Coin Slide Guards
- 15 Before You Start
- 15 Tools
- 15 Location
- 15 Exhaust
- 15 Electrical
- 16 Installing the Dryer
- 16 Step 1: Position and Level the Dryer Unit
- 16 Step 2: Connect Dryer Unit Exhaust System
- 17 Step 3: (Gas Dryer Only) Connect Gas Supply Pipe
- 18 Step 4: (Electric Dryer Only) Connect Electrical Plug
- 20 Step 5: Wipe Out Inside of Each Dryer
- 20 Step 6: Plug In the Dryer Unit
- 20 Step 7: Check Installation
- 21 Heat Source Check
- 21 Electric Dryers
- 21 Gas Dryers
- 23 Reversing Door Procedure
- 24 Electrical Requirements
- 24 Grounding and Wiring Instructions
- 26 Electrical Connection
- 26 Three-Wire Power Cord
- 27 Three-Wire Connection
- 28 Four-Wire Power Cord
- 30 Four-Wire Connection
- 31 Electrical Requirements
- 32 Grounding Instructions
- 33 Gas Requirements
- 35 Location Requirements
- 36 Dryer Exhaust Requirements
- 36 Exhaust System Materials
- 37 Make-Up Air Requirements
- 37 Make-Up Air Dos and Don’ts
- 37 Exhaust Direction
- 38 Exhaust System
- 39 Exhaust System Maintenance
- 39 Dryer Airflow
- 40 Multi-Dryer Installation Exhaust Requirements
- 42 Lint Filter
- 42 Motor Overload Protector
- 43 Operation
- 43 Operation Instructions for Electromechanical Dryers
- 43 Step 1: Clean Lint Filter
- 43 Step 2: Load Laundry
- 43 Step 3: Close Loading Door
- 43 Step 4: Determine Proper Dryer
- 44 Step 5: Set Fabric Selector
- 44 Step 6: Start Dryer
- 45 Operation Instructions for Electronic Display Control Dryers
- 45 Step 1: Clean Lint Filter
- 45 Step 2: Load Laundry
- 45 Step 3: Close Loading Door
- 45 Step 4: Determine Proper Dryer
- 46 Step 5: Set Fabric Selector
- 46 Step 6: Insert Coin(s) or Card
- 46 Step 7: Start Dryer
- 47 Indicator Lights
- 48 Operation Instructions for MDC Dryers
- 48 Step 1: Clean Lint Filter
- 48 Step 2: Load Laundry
- 48 Step 3: Close Loading Door
- 48 Step 4: Determine Proper Dryer
- 49 Step 5: Set Fabric Selector
- 49 Step 6: Insert Coin(s) or Card
- 49 Step 7: Start Dryer
- 50 Indicator Lights
- 51 Operation Instructions for Netmaster Dryers
- 51 Step 1: Clean Lint Filter
- 51 Step 2: Load Laundry
- 51 Step 3: Close Loading Door
- 51 Step 4: Determine Proper Dryer
- 52 Step 5: Set Fabric Selector
- 52 Step 6: Insert Coin(s) or Card
- 52 Step 7: Start Dryer
- 53 Indicator Lights
- 55 Maintenance
- 55 User-Maintenance Instructions
- 55 Lubrication
- 55 Care of Your Dryer
- 55 Exhaust System
- 55 For Energy Conservation
- 56 Before You Call for Service
- 57 If Service Is Required
- 58 Information for Handy Reference
- 65 Piezas de repuesto
- 67 Instrucciones de seguridad importantes
- 69 Instalación
- 69 Dimensiones aproximadas
- 69 Modelos para operar con monedas
- 70 Modelos para operar sin monedas
- 71 Seguridad adicional
- 71 Extensión para deslizador
- 71 Levas de regulación de tiempo
- 72 Protectores para los deslizadores para monedas
- 73 Antes de comenzar
- 73 Herramientas
- 73 Ubicación
- 73 Escape
- 73 Servicio eléctrico
- 74 Instalación de la unidad de secadoras
- 74 Paso 1: Coloque la unidad de secadoras en su lugar y nivélela
- 74 Paso 2: Conecte el sistema de escape de la unidad de secadoras
- 75 suministro de gas
- 76 clavijas eléctricas
- 78 Paso 5: Limpie el interior de cada una de las secadoras
- 78 Paso 6: Conecte cada una de las secadoras
- 78 Paso 7: Revise la instalación
- 79 Revisión de la fuente de calor
- 79 Secadoras eléctricas
- 79 Secadoras a gas
- 81 Cómo para invertir la posición de la puerta
- 82 Requisitos eléctricos
- 82 Instrucciones de cableado y de conexión a tierra
- 84 Conexión eléctrica
- 84 Cable de corriente de tres conductores
- 85 Conexión de tres conductores
- 86 Cable de corriente de cuatro conductores
- 88 Conexión de cuatro conductores
- 89 Requisitos eléctricos
- 90 Instrucciones para conectar a tierra
- 91 Requisitos de gas
- 93 Requisitos de ubicación
- 94 Requisitos para el escape de las secadoras
- 94 Materiales para el sistema de escape
- 95 Requisitos de aire de reposición
- 95 Qué hacer y qué no hacer
- 95 Dirección del escape
- 96 Sistema de escape
- 97 Mantenimiento del sistema de escape
- 97 Flujo de aire de la secadora
- 98 Requisitos para el escape de instalaciones múltiples de secadoras
- 100 Filtro de pelusa
- 100 Protector de sobrecarga del motor
- 101 Operación
- 101 Instrucciones de uso para secadoras electromecánicas
- 101 Paso 1: Limpie el filtro de pelusa
- 101 Paso 2: Meta la ropa
- 102 Paso 3: Cierre la puerta del tambor
- 102 Paso 4: Seleccione la secadora
- 102 Paso 5: Ajuste el selector de tela
- 103 Paso 6: Arranque la secadora
- 104 electrónico de pantalla
- 104 Paso 1: Limpie el filtro de pelusa
- 104 Paso 2: Meta la ropa
- 104 Paso 3: Cierre la puerta del tambor
- 105 Paso 4: Seleccione la secadora
- 105 Paso 5: Ajuste el selector de tela
- 105 Paso 6: Deposite las monedas o introduzca la tarjeta
- 106 Paso 7: Arranque la secadora
- 106 Luces indicadoras
- 107 Instrucciones de funcionamiento de las secadoras MDC
- 107 Paso 1: Limpieza del filtro de pelusa
- 107 Paso 2: Carga de la colada
- 107 Paso 3: Cierre de la puerta de carga
- 108 Paso 4: Establecimiento de la correspondiente secadora
- 108 Paso 5: Selección de la temperatura conforme a los tejidos
- 108 Paso 6: Introducción de monedas o de la tarjeta
- 109 Paso 7: Puesta en marcha de la secadora
- 109 Luces indicadoras
- 110 Instrucciones de funcionamiento de las secadoras NetMaster
- 110 Paso 1: Limpieza del filtro de pelusa
- 110 Paso 2: Carga de la colada
- 110 Paso 3: Cierre de la puerta de carga
- 111 Paso 4: Establecimiento de la correspondiente secadora
- 111 Paso 5: Selección de la temperatura conforme a los tejidos
- 111 Paso 6: Introducción de monedas o de la tarjeta
- 112 Paso 7: Puesta en marcha de la secadora
- 112 Luces indicadoras
- 113 Mantenimiento
- 113 Instrucciones de mantenimiento para el usuario
- 113 Lubricación
- 113 Cuidados a sus secadoras
- 113 Sistema de escape
- 113 Conservación de la energía
- 114 Antes de llamar para solicitar servicio de reparación
- 115 Si la secadora necesita mantenimiento
- 116 Información de referencia