advertisement
Chapter 4 — Configuration Command Reference
PDF417
PDF417 is only supported on the SF51 with PDF version.
Enables or disables decoding of PDF417 symbology. The
PDF417 symbology is a stacked 2D symbology that allows you to scan across rows of code. Each row consists of start/stop characters, row identifiers, and symbol characters, which consist of four bars and four spaces each and contain the actual data.
This symbology uses error correction symbol characters appended at the end to recover loss of data.
Macro PDF417, a feature of PDF417, extends the capability of
PDF417 by allowing up to 99,999 PDF417 symbols to be used to store data. The symbols are concatenated as they are scanned and can be scanned in any order.
Plessey
Enables or disables decoding of Plessey symbology. Plessey code is pulse-width modulated like most other bar codes. It includes a start character, data characters, an eight-bit cyclic check digit, a termination bar, and usually a reverse start character. The code is continuous and not self-checking. You need to configure two parameters for Plessey code: Start Code and Check Digit.
Postamble
Sets the postamble that is appended to any data you scan.
Common postambles include cursor controls such as a tab or a carriage return line feed. You can set Postamble to up to 20
ASCII characters.
Preamble
Sets the preamble that precedes any data you scan. Common preambles include a data location number or an operator number. You can set Preamble to up to 20 ASCII characters.
SF51 Cordless Scanner User’s Guide 43
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 16 Charging the Battery
- 16 Checking the Battery Status
- 24 Configuring With EasySet
- 25 Configuring From Your Intermec Computer
- 26 Restoring Default Settings
- 27 Configuring Security
- 28 Configuring the Discoverable State of the SF51
- 36 Getting Information About Your SF51
- 37 Problems and Possible Solutions
- 48 Administrator Reset Factory Defaults
- 48 Beep Duration
- 48 Beep Frequency
- 49 Beep Volume
- 49 Bluetooth Connect/Disconnect
- 49 Bluetooth Device Name
- 49 Bluetooth Device Page
- 50 Bluetooth Discoverable
- 50 Bluetooth PIN
- 50 Bluetooth Profile
- 50 Bluetooth Security
- 51 Codabar
- 51 Codablock A
- 51 Codablock F
- 51 Code 11
- 51 Code 39
- 52 Code 93/93i
- 52 Code 128 / EAN 128
- 52 ISBT 128
- 52 GTIN Processing for EAN 128
- 52 Configuration Modes and Utilities
- 53 Consecutive Same Read Data Validation
- 53 Disable All Symbologies
- 53 Error Beep
- 53 Good Read Beep Duration
- 53 Good Read Beep Number
- 54 Good Read Beep Timing
- 54 Good Read LED Duration
- 54 Interleaved 2 of 5
- 54 Matrix 2 of 5
- 54 Micro PDF417
- 54 MSI
- 55 PDF417
- 55 Plessey
- 55 Postamble
- 55 Preamble
- 56 RSS 14
- 56 RSS Expanded
- 56 RSS Limited
- 56 Setup Beep
- 56 Stacked Code Crackle
- 56 Standard 2 of 5
- 57 Symbology Identifier
- 57 Telepen
- 57 Timeout Between Different Consecutive Codes
- 58 Timeout Between Identical Consecutive Codes
- 58 Trigger Mode
- 59 UPC/EAN
- 59 ISBN
- 59 GTIN Processing
- 59 User Reset Factory Defaults
- 59 Vibrate Alert
- 59 Vibrate Alert Duration