- Industrial & lab equipment
- Electrical equipment & supplies
- Power generators
- Mase
- IS 21-24.5
- Installation manual
advertisement
I.S. 18 / 21 / 24 / 27 50
Hz
GB
- The generator is equipped with a magnetothermal switch which cuts the power in the event of an overload or short-circuit.
6.4 Earth connection
The generator casing must be firmly connected to earth.
Make the earth connection using the dedicated screw of the generator (Fig. 15 Ref. 2)
6.5 Generator/mains switching
A switch must be put on the utility line, which allows switching the utilities from the generator to an external power line. The switch must be dimensioned on the basis of the entity of loads involved; A broad diagram is shown in Fig.16.
7 HANDLING
For handling and lifting of the generator only use the lifting hooks located on the engine. To prevent balancing problems, use the hooks simultaneously and never individually.
Hooking the generator at points different from that indicated may cause damage to the generator or be dangerous to the operators.
8 WIRING DIAGRAM REFERENCES
See Fig.17 (standard wiring diagram)
1 Magnetothermal switch
2 Hour counter
3 Alternator
4 Rotor
5 Stator
6 Voltage regulator
7 Power terminal board
8 Emergency stop button
9 Thermal switch
10 START/STOP button
11 Engine protection module
12 Terminal board
13 Connector for remote control panel connection
14 Fuel gauge
15 Oil pressure gauge
16 Water temperature gauge
17 High water temperature sensor
18 High coolant temperature sensor
19 Oil pressure switch
20 Battery charger alternator
21 Stop electromagnet
22 Starter motor
23 Battery connection terminals
24 Panel connection cable
25 START/STOP button
26 Oil pressure gauge instrument
27 Coolant temperature gauge instrument
28 Remote control panel kit with instruments
29 Remote control panel kit
3 Ground screw
See Fig.18 (isolated pole wiring diagram)
1 ALTERNATOR
2 BATTERY CHARGER ALTERNATOR
3 BATTERY
4 12P CONNECTOR
5 HOUR COUNTER
6 DIODE
7 STOP ELECTROMAGNET
8 ENGINE PROTECTION MODULE
9 STARTER MOTOR
10 OIL PRESSURE SWITCH
11 EMERGENCY STOP BUTTON
12 ELECTRONIC VOLTAGE REGULATOR
13 ROTOR
14 STATOR
15 THERMAL SWITCH
16 ENGINE THERMOSTAT
17 TEMPERATURE GAUGE INSTRUMENT
18 OIL PRESSURE GAUGE INSTRUMENT
19 2P MAGNETOTHERMAL SWITCH
20 EARTH CONNECTION
21 RELAY
22 RELAY
23 START/STOP BUTTON
24 ALTERNATOR THERMOSTAT
25 TEMPERATURE SENSOR
26 OIL PRESSURE SENSOR
27 CONNECTOR 6P
GB
- 13
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Figure
- 6 Schema elettrico
- 9 INFORMAZIONI GENERALI
- 9 Simbologia
- 10 l'installazione e la messa in servizio
- 10 INSTALLAZIONE
- 10 Caratteristiche del vano
- 10 Ancoraggio del gruppo
- 10 Ventilazione
- 10 Sistema di adduzione dell'acqua di mare
- 11 sopra la linea di galleggiamento (fig.4)
- 11 la linea di galleggiamento (fig.5)
- 11 (fig.6)
- 11 (fig.7)
- 11 Componenti
- 12 Sistema di scarico
- 12 CIRCUITO COMBUSTIBILE
- 12 COLLEGAMENTI ELETTRICI
- 12 Allacciamento batteria
- 13 Allacciamento c.a
- 13 Collegamento di terra
- 13 Commutazione generatore - rete
- 13 MOVIMENTAZIONE
- 13 RIFERIMENTI SCHEMA ELETTRICO
- 10 Pictures
- 14 Wiring diagram
- 17 General information
- 18 and set-up
- 18 INSTALLATION
- 18 Housing characteristics
- 18 Generator anchorage
- 18 Ventilation
- 18 COOLING WATER CIRCUIT
- 18 Seawater feed system
- 18 waterline (fig.4)
- 19 water line (Fig.5)
- 19 waterline (fig.6)
- 19 waterline (fig.7)
- 19 Components
- 20 Exhaust system
- 20 5 FUEL CIRCUIT
- 20 6 ELECTRICAL CONNECTIONS
- 20 Battery connection
- 20 Remote control panel connection
- 20 AC connection
- 21 Earth connection
- 21 Generator/mains switching
- 21 HANDLING
- 21 WIRING DIAGRAM REFERENCES