advertisement
Comm FMS Board Connections
Appendix
Appendix
Comm FMS Board Connections
The following pictures and diagrams indicate the common wiring location and wire colours for the Comm FMS board.
Due to the wide range of configurations, actual wiring in the unit may vary from what is shown here.
Figure 35: ComFutra FMS Board
Connections
Connecter shown below is for the capacitive (hard) type key pad. Refer to membrane key pad wiring for soft type key pad wiring.
Compac Industries Ltd.
Page 124 www.compac.co.nz
Appendix
Comm FMS Board Connections
For a "White Card" and Fuelcard enabled unit the receipt printer plugs into Port 3 TTL of the
Comm FMS board as shown below:
Compac Industries Ltd.
Page 125 www.compac.co.nz
Comm FMS Board Connections
Appendix
For a Credit Card enabled unit the plug for Port 3 TTL is wired like this and terminates at the
Comm FMS RS232 Port Expansion Board.
Compac Industries Ltd.
Page 126 www.compac.co.nz
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Conditions of Use
- 6 Product Identification
- 7 Document Control Information
- 8 Symbols and Units of Measure
- 9 Safety
- 10 Introduction
- 11 Options
- 12 Components
- 14 Litres Total
- 15 Installation Guidelines
- 18 Electrical Connections
- 19 Tank Gauging Setup
- 19 Precautions when using Generator Power
- 20 Wiring Diagram
- 21 Modem Connections
- 23 Operating Instructions
- 23 CWID Key & CWID Block Readers
- 25 HID Readers
- 26 iTrack Reader
- 27 USB Module
- 28 USB Memory Stick
- 29 Uploading and Downloading Files
- 30 1) Do All
- 31 2) Set Price
- 31 3) Send Cards
- 32 4) Get Buffer
- 32 5) Get Transactions
- 33 Working with USB Module Files
- 34 1) Cards
- 36 2) Price
- 37 3) Transactions
- 38 Customising Your Transaction Reports
- 40 Powering Up
- 41 Set Up
- 41 System Setup
- 42 Main Menu Options
- 42 Option #1 REPORTS
- 43 Option #2 CARDS
- 44 Option #3 FUELS
- 46 Option #4 SYSTEM
- 55 Option #5 PUMPS
- 58 Comms Options
- 64 Option #6 TANKS
- 68 Option #7 PRODUCT GROUPS and GRADES
- 69 Tanks/Pumps/Groups
- 71 Setting Product Groups
- 72 Assigning Pump Numbers to Hoses
- 72 Pump numbers for each model
- 72 Order of pump numbers
- 72 Assigning Hoses to Product Groups
- 73 Legend 4 Hose, 6 Hose and Laser 4 Hose Quad
- 74 Master, Premier and Laser (Single and Dual)
- 75 Cards
- 75 Expiry Date
- 75 Setting ISO and Access codes
- 76 Oil company ISO and Access codes
- 77 ATG / CE Box
- 78 Mechanical Registers
- 82 Cardreaders
- 83 Modems
- 83 Dynalink (Hayes type)
- 83 GSM Modem (Wavecom)
- 84 Lantronix
- 88 Diagnostic LEDs
- 89 Diagnostic LEDs in a system with Compac comms only
- 90 Reports
- 91 Deleting Transactions
- 92 Troubleshooting
- 92 Error Messages
- 93 Service and Upgrade Procedures
- 93 Com FMS Board Replacement (DCA)
- 96 C4000 Board Replacement
- 97 Compac Box Replacement
- 98 Fit PC Replacement
- 99 Wiring a USB Module
- 102 CWID Interface Board Replacement
- 104 CWID Aerial Replacement
- 105 CWID Nozzle Aerial Replacement
- 107 HID Reader Replacement
- 109 iTrack Reader Installation and Replacement
- 112 Card Reader Replacement
- 115 Multiplex Board Replacement
- 116 Keypad and Display Screen Replacement
- 117 Router / Switch Replacement
- 118 Replacing the Receipt Printer
- 119 Software Upgrading
- 121 Maintenance
- 122 Receipt Printer
- 122 Changing Paper on a Custom Printer
- 124 Appendix
- 124 Comm FMS Board Connections
- 127 Plugs and Connectors
- 131 Part Locations
- 133 Spare Parts List
- 133 DCA Cabinet
- 134 Electronic Components
- 135 Modem / Router Options (DCA)
- 135 Printer
- 135 Card Reader
- 136 CWID HID & USB
- 136 Exchange Parts
- 137 Glossary of Terms
- 138 Installation Checklist