advertisement
User Manual
Normally, RTU always keeps online and always be ready for data transmission. But in some circumstances, it’s important to reduce wireless data flow. To realize this function, the software can makes RTU into sleep state in idle time. When there is application data to transmit, RTU can be triggered online ready for data transmission. There are total five methods to make RTU online:
AUTO: RTU always keeps online
SMSD: send a special short message to make RTU online
CTRL: make RTU online through a phone call to RTU
DATA: send special serial data to make RTU online
MIXD: the combination of SMSD, CTRL, DATA. RTU will be online when meet one of these three trigger methods.
AT Command:
AT+ACTI=xxxx xxxx: one of the above trigger methods
When RTU enable trigger mode, and enable “Disconnect to Trigger mode” function. The RTU will re-enter trigger mode when it connect to the network fail or the network connection broken.
This will make RTU enter into sleep state.
AT Command:
AT+ISTRIGMODE=x x range 0-1, 0 means disable, 1 means enable
Debug information is used to debug software when there is software problem.
0 --- no debug information output
Waveloc Ltd. - 6 Vasiliou Tsitsani str. Glyfada, 16675 Attiki, Greece - http://waveloc.com
Property of Xiamen Four-Faith Communication Technology Co., Ltd. All rights reserved.
Page 53 of 96
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 30 ◆Digitalinputfunction
- 31 ◆MODBUSlogiccorrespondingfunction
- 31 ◆Acquisitionpurpose
- 31 ◆Acquisitioninterval
- 32 ◆Alarmtriggercondition
- 32 ◆Alarmcontent
- 32 ◆Alarmphonenumber
- 33 ◆Digitaloutputfunction
- 34 ◆MODBUSlogic1output
- 34 ◆MODBUSlogic0output
- 34 ◆MODBUSlogic1square-wavecycle
- 35 ◆MODBUSlogic0square-wavecycle
- 35 ◆Defaultoutputvoltage
- 36 ◆Analoginputfunction
- 36 ◆Setsensorrange
- 38 ◆Setsensorvoltageorcurrentoutput
- 39 ◆MODBUSfunction
- 39 ◆Acqisitionfunction
- 39 ◆Acqisitioninterval
- 39 ◆Alarmtriggercondition
- 40 ◆Alarmcontent
- 40 ◆Alarmphonenumber
- 41 ◆Activereportfunction
- 42 ◆Counterfunction
- 42 ◆Counterworkmode
- 42 ◆Counterinitialvalue
- 42 ◆Alarmfunction
- 43 ◆Alarmcontent
- 43 ◆Alarmphonenumber
- 43 ◆Alarmupperlimit
- 44 ◆Activereportinterval
- 44 ◆Alarmreportmethod
- 44 ◆Continuousalarminterval
- 45 ◆Continuousalarmnumberoftimes
- 45 ◆Alarmadministratornumber
- 46 ◆ModBusworkmode
- 47 ◆ModBusaddress
- 47 ◆RTUworkmode
- 48 ◆DataCenterNumber
- 49 ◆MainCenterAddr+Port:
- 49 ◆BackupCenterAddr+Port:
- 50 ◆MultiDSCConfiguration
- 51 ◆MainandBackupCenterDNSServer
- 51 ◆Center2~5DNSServer
- 52 ◆WorkMode
- 53 ◆TriggerType
- 53 ◆DisconnecttoTriggermode
- 53 ◆DebugLevel
- 54 ◆Databit,Parity,Stopbit
- 54 ◆CommunicationBaudrate
- 55 ◆AutoBackToMainServer
- 55 ◆DeviceID
- 55 ◆SIMCardNo
- 56 ◆BytesInterval
- 56 ◆CustomRegisterString
- 56 ◆CustomHeartbeatString
- 57 ◆Reconnectsetting
- 57 ◆Transfermeanning
- 58 ◆Network
- 59 ◆SMSCenter
- 59 ◆HeartbeatInterval
- 60 ◆CallTriggerPhoneNo
- 60 ◆SMSTriggerPassword
- 60 ◆DataTriggerPassword
- 61 ◆TCPMTU
- 61 ◆MultiCenterReconnectInterval
- 61 ◆SetparameterofconfigureSMS
- 62 ◆RTC(RealTimeClock)TimeSetting
- 63 ◆PowerOn/OffSetting
- 72 ◆Destinationnumber
- 73 ◆SMSSendingFormat
- 73 ◆DatauploadStyle
- 74 ◆ShowConfigure
- 74 ◆ShowBaudrate
- 74 ◆AutoDetect
- 74 ◆VersionDisplay
- 74 ◆SignalValue
- 75 ◆Factorysetting
- 75 ◆ClearOutput
- 75 ◆SaveOutput
- 75 ◆Browse
- 75 ◆SaveConfigure
- 75 ◆LoadConfigure