- Industrial & lab equipment
- Electrical equipment & supplies
- Electrical controls
- Electrical timers
- Advantech
- TPC-1570H
- User manual
advertisement
4.4 Dual Display Setting
If you use CRT monitor, you must Connections to CRT port in during system boot up. During system boot up, the system will set CRT parameter. If you have multiple devices, you can set them.
Step 1: Click Intel graphic icon from the toolbars
Step 2: Select Graphics Options -> Output Device
Step 3: This control allows selection of a device page. The currently active is indicated by a checkmark on the icon. If you have multiple devices, activation of an alternate device is accomplished by selecting that device icon. Then, select either Apply or OK button. Intel Dual Display Clone is for CRT monitor and TPC-1570 LCD as the below.
41 Chapter 4
TPC-1570H User Manual 42
2
5
Windows XP Embedded
Sections include:
• EWF
• HORM
• Advantech Utilities
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 12 1 General Information
- 12 Introduction
- 12 Specifications
- 12 System Kernel
- 13 I/O Ports
- 13 Safety and Environment
- 14 LCD Specifications
- 15 Touchscreen Specifications
- 15 Power
- 15 I/O Port Arrangement
- 15 Figure 1.1:I/O port arrangement
- 16 Panel Mounting
- 16 Figure 1.2:Panel Mounting
- 17 Exploded Diagram
- 17 Figure 1.3:Exploded Diagram
- 17 Dimensions and cutout
- 18 Figure 1.4:Dimensions
- 20 2 System Setup
- 20 Figure 2.1:Unpack the package
- 21 Figure 2.2:Install CompactFlash memory card
- 22 Figure 2.3:Power connector
- 23 Figure 2.5:Touchscreen Calibration
- 23 Figure 2.6:Touchscreen Calibration
- 26 3 System Engine
- 27 Figure 3.1:Main Board Connector
- 27 Figure 3.2:Main Board Connector
- 30 4 Software Configuration
- 30 Utilities & Drivers
- 30 Intel Chipset Software Installation Utility
- 30 VGA Drivers (Intel(R) Graphics Driver)
- 30 Intel PRO Network Drivers/software
- 31 Audio Driver
- 31 Advantech COM Driver
- 31 Touchscreen Driver
- 31 Watchdog Timer Driver
- 32 Advantech COM Driver Installation
- 42 Watchdog Timer (WDT) Driver Installation
- 43 Installing the TPC-1570 Watchdog Timer Driver
- 48 How to Use the TPC-1570H Watchdog Timer
- 51 Dual Display Setting
- 54 5 Windows XP Embedded
- 55 Advantech Utilities
- 55 Version Information
- 55 OSLock and OSUnLock
- 58 Appendix A Serial Port Settings
- 58 COM1/ COM3 Connector Definition
- 58 COM4 Setting
- 62 Appendix B Watchdog Timer on WinCE
- 62 DeviceIOControl
- 64 How to Use the Control Code
- 66 Examples
- 70 Overview
- 71 Watchdog Timer Programming
- 72 Table C.1:Watchdog Timer Registers
- 73 Example Programs
- 80 Appendix D Accessory Kit Assembly
- 80 CompactFlash to IDE Transfer Kit
- 80 Figure D.1:Adapter Board and IDE Cable
- 81 Figure D.3:CompactFlash Slot
- 81 Figure D.5:Inserted Adapter Board
- 82 Figure D.7:Plug Power Line into CD-ROM Drive
- 82 USB Driver Installation Notice
- 84 Appendix E HDD Kit Assembly
- 84 Figure E.1:Removing the Rear Cover
- 84 Figure E.2:Removing the Top Screws
- 85 Figure E.3:Removing the HDD kit
- 85 Figure E.4:Pulling out the HDD bracket
- 86 Figure E.5:The HDD Bracket
- 86 Figure E.6:Installing the HDDr
- 87 Figure E.7:Linking the HDD with the Connector
- 87 Figure E.8:Fastening the HDD cover
- 88 Figure E.9:Chamfer
- 88 Figure E.10:Chamfer & Rubber
- 89 Figure E.11:Sliding the HDD Into Position
- 89 Figure E.12:Completed HDD Installation
- 90 Figure E.13:Mounting the Rubber Cushions
- 90 Figure E.14:Fastening the HDD Module
- 91 Figure E.15:Reinstalling the Rear Cover
- 94 Driver Installation
- 94 Figure F.1:Setup.exe
- 94 Figure F.2:Install - Wizard
- 95 Figure F.3:Install – License Agreement
- 95 Figure F.4:Install – Completed
- 96 Uninstall the Driver
- 96 Figure F.5:Uninstall
- 96 Figure F.6:Uninstall
- 97 Figure F.7:Uninstall
- 97 Touchscreen Calibration
- 98 Figure F.8:Standard Calibration
- 98 Figure F.9:Standard Calibration
- 99 Figure F.10:Standard Calibration
- 100 Figure F.11:Advanced Calibration
- 100 Figure F.12:Advanced Calibration
- 101 Figure F.13:Plot Calibration Data
- 102 Figure F.14:Draw
- 102 Figure F.15:Clear Screen
- 103 Figure F.16:Option
- 106 Appendix G Fuse Specifications
- 106 Fuse Specifications
- 106 Fuse Replacement
- 106 Figure G.1:Fuse Replacement