advertisement
Installation Instructions
PREPARE HOT WATER SUPPLY
Hot Water Line
• The line may enter from either side, rear or floor within the shaded area shown in Figure F.
• The line may pass through the same hole as the electrical cable and drain hose, or an additional
1-1/2" diameter hole may be cut to accommodate the water line. If a power cord with plug is used, the water line must not pass through the power cord hole.
STEP 1 LOCATE INSTALLATION ITEMS
• Locate the items in the installation package and set aside for use in the listed steps.
• Trim pieces – Step 2
• Junction box cover – Step 7 or Step 18
• Drain hose and clamp – Step 10
• Screw kit – Step 15
• Drain hose hanger – Step 17
• Owner’s Manual – Step 19 and Step 24
• Hard water test strip – Step 21
• Sound upgrade kit (selected models) – Step 22
• Product samples and/or coupons – Step 24
Shut-off
Valve
1-1/2"
Dia.
Hole
5"
4"
5"
4"
Hot
2"
From
Cabinet
19" From Wall
6"
Cabinet Face
2" From Floor
Figure F
Water Line Connection
• Turn off the water supply.
• Install a hand shut-off valve in an accessible location, such as under the sink. (Optional, but strongly recommended and may be required by local codes.)
• The water connection is on the bottom left side of the dishwasher. Install the hot water inlet line, using
3/8" or larger copper tubing. Route the line as shown in
Figure F and extend forward at least 19" from rear wall.
• Adjust the water heater to deliver water between 120°F and 150°F.
• Flush water line to clean out debris. Use a bucket to catch water and debris.
• The hot water supply line pressure must be between
20 and 120 PSI.
CAUTION
The hot water supply line pressure must be at least
20 PSI. Lower pressures could cause the water valve to leak and cause water damage.
CAUTION
Do not remove wood base until you are ready to install the dishwasher. The dishwasher will tip over when the door is opened if the wood base is removed.
7
STEP 2 INSTALL TRIM PIECES
In this step, you will need the trim pieces set aside in Step 1.
• Press top trim piece onto top of tub flange. Start with the right edge and work your way to the left.
• Repeat process with the left and right trim pieces working from the top down.
• Open and close the door to check that trim does not bind and does not interfere with door latch or door hinges.
Trim
Strip
Trim
Strip
Trim
Strip
Figure G
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Parts Supplied
- 3 Materials You Will Need
- 3 Tools You Will Need
- 4 Advance Planning
- 4 Prepare Dishwasher Enclosure
- 5 Prepare Drain Plumbing
- 6 Prepare Electrical Wiring
- 7 Prepare Hot Water Line
- 7 Step 1, Locate Installation Items
- 7 Step 2, Install Trim Pieces
- 8 Step 3, Check Door Balance
- 8 Step 4, Remove Wood Base, Install Leveling Legs
- 8 Step 5, Remove ToeKick
- 8 Step 6, Remove ToeKick Brace
- 9 Step 7, Install Power Cord
- 9 Step 8, Install 90° Elbow
- 9 Step 9, Position Water Line and Housing Wiring
- 9 Step 10, Install Drain Hose to Dishwasher Drain Port
- 10 Step 11, Insert Drain Hose Through Cabinet
- 10 Three-Fourths of the Way Into Cabinet
- 11 Step 13, Slide Dishwasher Into Final Position
- 11 Step 14, Level Dishwasher
- 12 to Countertop or Cabinet
- 12 Step 16, Connect Water Supply
- 13 Step 17, Connect Drain Line
- 14 Step 18, Connect Power Supply
- 14 Step 19, Pretest Checklist
- 15 Step 20, Dishwasher Wet Test
- 15 Step 21, Set Water Hardness
- 15 Step 22, Install Sound Upgrade Kit if Equipped