advertisement
Installation Instructions/Custom Panel Dimensions
STEP 20 DISHWASHER WET TEST
• Turn on power supply (or plug power cord into outlet, if equipped).
• Start the unit to check for leaks.
– Push RINSE ONLY pad.
– Push START/RESET pad one time.
– Close door.
• Check to be sure that water enters the dishwasher. If water does not enter the dishwasher, check to be sure that water and power are turned on.
• Check for leaks under the dishwasher. If a leak is found, turn power supply off, then tighten connections. Restore power after leak is corrected.
• Check for leaks around the door. A leak around the door could be caused by door rubbing or hitting against adjacent cabinetry. Reposition the dishwasher if necessary. See Step 13, 14 and 15.
• The dishwasher will drain and turn off about 5 minutes after it was started. Check drain lines. If leaks are found, turn off power supply and correct plumbing as necessary. Restore power after corrections are made. See Step 10 and 17.
• Open dishwasher door and make sure most of the water has drained. If not, check that disposer plug has been removed and/or air gap is clear. See Step 17. Also check drain line to be sure it is not kinked.
• Run the dishwasher through another “Rinse Only” cycle.
Check for leaks and correct if required.
STEP 22 INSTALL SOUND UPGRADE KIT
IF EQUIPPED
Skip this step if your model does not have the Sound
Upgrade Kit.
• Locate sound upgrade kit set aside in Step 1 and the two screws set aside in Step 6.
• Attach the plastic Sound Panel as shown in Figure II using the two screws. The lower set of mounting holes should be used.
• Be sure the sound panel is seated in the notches on frame as shown in Figure II.
Sound panel is located under door panel.
Plastic Sound
Panel with Foam
STEP 21 SET WATER HARDNESS
Models with bulk dispenser only. Skip this step if your dishwasher does not have the bulk dispense feature.
• Locate the hard water test strip set aside in Step 1.
• Remove strip from package.
• Turn on the hot water and hold the strip under the stream, following the directions on the package.
• Use the value on the test strip to calibrate your dishwasher for water hardness. Refer to the section titled "Water
Hardness Calibration" in your Owner's Manual for information on how to calibrate your dishwasher.
Be sure that the sound panel is seated in the notch in the frame. (Both sides)
Attachment
Screws
Figure II
15
STEP 23 INSTALL TOEKICK
• Locate toekick and screws set aside in step 5.
Toekick
Figure JJ
Attachment
Screws
• Replace the toekick and make sure it is against the floor.
• Insert and tighten the 2 toekick attachment screws. The toekick should stay in contact with the floor to ensure quiet dishwasher operation.
STEP 24 LITERATURE
• Be sure to leave complete literature package, Installation
Instructions and product samples with the consumer.
NOTE: While performing installations described in this book, safety glasses or goggles should be worn.
For Monogram
® local service in your area, call
1.800.444.1845.
NOTE: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and specifications are subject to change without notice.
Pub. No. 31-30246
Part No. 206C1559P184
10-08 JR
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY 40225 ge.com
advertisement
Related manuals
advertisement
Table of contents
- 3 Parts Supplied
- 3 Materials You Will Need
- 3 Tools You Will Need
- 4 Advance Planning
- 4 Prepare Dishwasher Enclosure
- 5 Prepare Drain Plumbing
- 6 Prepare Electrical Wiring
- 7 Prepare Hot Water Line
- 7 Step 1, Locate Installation Items
- 7 Step 2, Install Trim Pieces
- 8 Step 3, Check Door Balance
- 8 Step 4, Remove Wood Base, Install Leveling Legs
- 8 Step 5, Remove ToeKick
- 8 Step 6, Remove ToeKick Brace
- 9 Step 7, Install Power Cord
- 9 Step 8, Install 90° Elbow
- 9 Step 9, Position Water Line and Housing Wiring
- 9 Step 10, Install Drain Hose to Dishwasher Drain Port
- 10 Step 11, Insert Drain Hose Through Cabinet
- 10 Three-Fourths of the Way Into Cabinet
- 11 Step 13, Slide Dishwasher Into Final Position
- 11 Step 14, Level Dishwasher
- 12 to Countertop or Cabinet
- 12 Step 16, Connect Water Supply
- 13 Step 17, Connect Drain Line
- 14 Step 18, Connect Power Supply
- 14 Step 19, Pretest Checklist
- 15 Step 20, Dishwasher Wet Test
- 15 Step 21, Set Water Hardness
- 15 Step 22, Install Sound Upgrade Kit if Equipped