- No category
Victaulic AGS Roller Set 14 Inch to 16 Inch for use on VE416 FSD Specification Sheet
Add to my manuals
36 Pages
advertisement
Pipe Preparation Tool Specifications
VE460
Fab Shop Roll Groover
VE12
Manual Roll Groover
VG824
Cut Groover
VAPS1672
Pipe Stand
Grooved Piping System
The distinguishing feature of the Victaulic grooved mechanical piping system is, as the name implies, a groove where the pipe and fitting engage to form a selfrestraining joint. The position, depth and cross-section of this groove combine with the fitting housing in an optimal strength-to-weight relationship. The result is a permanent connection capable of withstanding thrust loads up to the maximum rated operating pressure.
24.01
Roll Grooving
Roll grooving is the method of choice for preparing pipe made of standard or lightwall carbon steel, stainless steel, aluminum, PVC, copper and other materials. Both roll and cut grooving meet the requirements of ANSI/
AWWA C-606. For optimal joint performance Victaulic recommends that each pipe end be square cut. However, beveled end pipe may be used provided the wall thickness is standard or less, and the bevel meets ASME/
ANSI B16.25 (37 1/2°) or ASTM A-53 (30°). Square cut pipe must be used with FlushSeal
®
and EndSeal
®
gaskets.
Victaulic roll grooving tools are all designed to rotate the pipe or orbit the pipe as a male grooving roll is impressed into the pipe. The support roll, in addition to driving the pipe or tool, is the female die inside the pipe.
For all but the VE12, VE26, VE46, VE106, and VE226 tools, Victaulic roll groovers use hydraulic pressure to force the grooving roll into the pipe to form the groove.
Roll grooving removes no metal; the groove is cold formed into the pipe wall.
Cut Grooving
All Victaulic cut groovers are designed to be driven around a stationary pipe to machine away material, providing a groove. The design of the tool assures a groove which is concentric with the pipe O.D., even with out-of-round pipe. Cut grooving is designed for standard weight or heavier wall thicknesses of pipe. A square cut groove is used for steel and other metallic IPS pipe. This provides maximum coupling gripping efficiency and the fullest pipe movement capabilities.
Job/Owner
System No.
Location
Contractor
Submitted By
Date
victaulic.com
| Pipe Preparation Tools | Publication 24.01
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
1
Engineer
Spec Section
Paragraph
Approved
Date
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Table of Contents
Roll Grooving – Field Manual
These tools are designed for light duty manual field use and do not require a power source to operate.
Alternatively, select field manual tools may also be operated with a compatible power drive.
VE12 ....................................................................................... 4
VE26 ....................................................................................... 4
VE26/46 Power Drive Kit ......................................................... 5
VE46 ....................................................................................... 5
Roll Grooving – Field Portable
These tools are designed for light to heavy duty field use with tool components that can be easily unassembled and toted around the job site.
VE106/107 .............................................................................. 6
VE206 ..................................................................................... 7
VE226 ..................................................................................... 8
VE226 Power Drive Kit ............................................................ 8
Roll Grooving – Field Fabrication
These tools are designed for heavy duty repetitive field use.
Requires External Power Source
VE272SFS ............................................................................... 9
VE416FS ................................................................................10
Power Drive Self-Contained with Tool
VE270FSD/VE271FSD ............................................................11
VE416FSD/VE417FSD ............................................................12
VE450 ....................................................................................13
Roll Grooving – Plant/Shop Fabrication
These tools are designed for heavy duty repetitive plant or shop fabrication use.
VE268 ....................................................................................14
VE414MC ...............................................................................15
VE460 ....................................................................................16
VE872 ....................................................................................18
Cut Grooving – Field Manual
These tools are designed for light duty manual field use and do not require an electrical power source for operation.
VG Vic-Groover ........................................................................19
Cut Grooving – Field Fabrication
These tools are designed for heavy duty repetitive field or shop use and require a power drive for operation. Victaulic offers the Power Mule II listed under tool accessories.
VG28GD ................................................................................ 20
VG28GD-ABR ........................................................................ 20
VDG26GD .............................................................................. 20
VG26GD-COR .........................................................................21
VG824 ................................................................................... 22
VG824-ABR ........................................................................... 22
VG824DG .............................................................................. 22
VG824-COR ........................................................................... 23
VG828 ................................................................................... 23
Cut Grooving- Field Motorized
This tool is designed for occasional field use to cut off and cut groove ductile iron pipe.
VG412 ....................................................................................24
Plastic Groovers
These tools are designed for field fabrication use to cut a radius groove into PVC Plastic.
VPG26 ....................................................................................25
VPG824 ..................................................................................25
Aquamine Grooving Tools
This lightweight and portable tool is designed to manually cut a spline groove and beveled end on
Aquamine pipe for Aquamine reusable couplings.
APG ........................................................................................25
Hole Cutting Tools
These lightweight and portable tools are designed to cut holes into pipe for branch connections.
HCT904 ................................................................................ 26
HCT908 ................................................................................ 26
VHCT900 .............................................................................. 26
Vic-Tap II ............................................................................... 26
Vic-Press Tools
This battery-operated hand-held tool is designed for securing Vic-Press Schedule 10S products onto IPS
Schedule 10S stainless steel pipe.
PFT510 ..................................................................................27
Pipe Cut-Off Tools
These lightweight and portable tools are designed to cut off pipe ends using a flame torch assembly.
VCT1 ..................................................................................... 28
VCT2 ..................................................................................... 28
Tool Accessories
These tool accessories are designed to assist in the operation and grooving procedure of a variety of
Victaulic tools as specifically outlined.
VPD752 Power Drive for Roll Grooving Tools .......................... 29
Power Mule II Power Drive for Cut Grooving Tools .................. 29
VAPS112 Pipe Stand ............................................................. 30
VAPS224 Pipe Stand ............................................................. 30
VAPS1672 Pipe Stand ........................................................... 30
PT100A/PT101 Pipe Tape ......................................................31
PT102 Pipe Tape ....................................................................31
Fabrication Cell
These tool accessories are part of a turn-key fab shop package to maximize productivity gains.
VAP131 Fabrication Cell Package .......................................... 32
VAPS 131R Hydraulic Adjustable Pipe Stand ......................... 32
VAPS 131F Hydraulic Positioner ............................................ 32
VAPS 131T Assembly Table ................................................... 32
VBSP Closure Tools
These tools are specifically designed for use with installing
Victaulic Bolted Split Sleeve Products (VBSP).
CTM-01 Small Manual ........................................................... 33
CTM-02 Large Manual ........................................................... 33
CTH-01 Small Hydraulic ........................................................ 33
CTH-02 Large Hydraulic ........................................................ 33
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
2
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Groove Set Selection:
In order to achieve Victaulic specified product performance, the proper Victaulic roll grooving tool and corresponding Victaulic roll set must be selected.
Failure to select the appropriate Victaulic roll set, or to use the correct Victaulic tool, may result in reduced performance or product failure. Tool specifications and capacities are listed with each tool.
The chart below provides an overview of commonly used roll sets. In addition to the roll sets detailed below, numerous specialized roll sets are also available, such as the “RZ” roll set used for grooving pipe used with
EndSeal
®
Style HP-70ES couplings. If your preferred pipe material or size is not referenced in the below chart, please contact Victaulic for more information.
Pipe Material IPS/CTS Wall Thickness
Carbon Steel
Stainless Steel 1
Schedule 5 through
Standard Wall
Schedule 40S through
Standard Wall
Light Wall
Stainless Steel 1
Schedule 5S and 10S
Aluminum Schedule 5 through 40
PVC Plastic
Copper
Schedule 40 and 80
K, L, M, DWV
Pipe Sizes
¾ – 8"/20 – 200mm
R (Standard Rolls)
R9 (Standard Rolls)
RX (Light Wall
Stainless Steel Rolls)
RP (Plastic and
Aluminum Rolls)
RP (Plastic and
Aluminum Rolls)
RR (Copper Rolls)
Recommended Roll Set
Pipe Sizes
10 – 12"/250 – 300mm
Pipe Sizes
14 – 24"/350 – 600mm
R9 (Standard Rolls)
R9 (Standard Rolls)
RX (Light Wall
Stainless Steel Rolls)
RP (Plastic and
Aluminum Rolls)
RW (AGS Rolls) or RS
(Extra Strong Rolls)
RW (AGS Rolls)
RWX (AGS Light Wall
Stainless Rolls)
Pipe Sizes
26 – 72"/650 – 1800mm
RW (AGS Rolls)
Additional specialized roll sets are available. If your pipe material or size is not listed here, please call Victaulic Customer Care for more information.
1 Stainless Steel is defined as Type 304(L) or 316(L). For Duplex and Superduplex stainless steels, contact Victaulic for more information.
Victaulic Roll Grooving
For proper selection of grooving rolls for different alloys, please use the following selection guide. Also note all tools are equipped with carbon steel rolls only. All other types of grooving rolls are optional.
Groove Type
OGS
AGS
Stainless Steel – OGS
Stainless Steel – AGS
ES
Copper
PVC/Aluminum
Color Code
Black
Black/Yellow Strip
Black
Silver
Black/Yellow Strip
Silver
Black
Copper
Gold
Alloy
Carbon Steel
Carbon Steel
Stainless Steel (Standard Wall Only)
Stainless Steel (Light Wall Only)
Stainless Steel (Standard Wall Only)
Stainless Steel (Light Wall Only)
Carbon Steel
Copper
PVC/Aluminum
Part Number Indentification
R
RW
R
RX
RW
RWX
RZ
RR
RP
WARNING
• Victaulic RX roll sets must be used when grooving light-wall/thin-wall stainless steel pipe for use with Victaulic Couplings.
Failure to use Victaulic RX roll sets when grooving light-wall/thin-wall stainless steel pipe may cause joint failure, resulting in serious personal injury and/ or property damage.
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
3
NOTICE
• Victaulic grooving rolls for any pipe material other than carbon steel must be ordered separately.
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Field Manual
VE12
VE26
VE12 Groove In-Place
• Tool is manually operated using the supplied handle
• For manual grooving of Schedule 5, 10 and 40 steel; stainless steel; aluminum and PVC pipe
• Enhanced tracking rolls allow bi-directional grooving
• Roll grooves ¾ – 2"/20 – 50 mm pipe
Power Requirements: None
Weight: 17 lbs./8 kg
Tool Ratings — Maximum
Pipe Size Capacity
Pipe Size (in
Model Pipe Material Notes
VE12
VE12SS
Steel
Stainless
Aluminum
PVC Plastic
Lt. Wall SS
2
¾
20
5 – 10
5 – 10
|
mm) / Schedule
1
25
1¼
32
5S – 10S
5 – 40
40S
5 – 40
40
1½
40
2
50
2 6061-T4 or 6063-T4 Alloy must be used.
VE26 Groove In-Place
• Tool is manually operated using the supplied handle
• Repair and retrofit existing lightwall steel, Schedule 40 steel, stainless steel,
PVC, and aluminum
• Enhanced tracking rolls allow bi-directional grooving
• Available for copper tubing (CTS) Types K, L, M and DWV plus British, DIN, and Australian Standard copper
• Optional power drive adapter kit available to alternately groove pipe using a
Ridgid* 300 power drive or Victaulic VPD752
• Roll grooves 2 – 6"/50 – 150 mm pipe
Power Requirements: None
Weight: 22 lbs./10 kg
Tool Ratings — Maximum
Pipe Size Capacity
Model Pipe Material Notes
VE26S
VE26C
VE26P
VE26SS
Steel
Stainless
Copper
Aluminum
PVC Plastic
Lt. Wall SS
2
Pipe Size (in
|
mm) / Schedule
2
50
2½
60
3
80
4
100
5 – 40 5 – 10
40S Only
K, L, M and DWV
5 – 40 5 – 10
40
5S – 10S
5
125
6
150
2 6061-T4 or 6063-T4 Alloy must be used.
* Ridgid is a registered trademark of the Ridge Tool Company.
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
4
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Field Manual
VE46
VE46 Groove In-Place
• Tool is manually operated using the supplied handle
• Designed for manually roll grooving Schedule 40 steel, aluminum, stainless steel and PVC pipe and Schedule 80 PVC pipe
• Enhanced tracking rolls allow bi-directional grooving and helps to hold the tool on the pipe end during the roll grooving process
• Optional power drive adapter kit available to alternately groove pipe using a
Ridgid* 300 power drive or Victaulic VPD752
• Roll grooves 3½ – 6"/90 – 150 mm pipe
Power Requirements: None
Weight: 28 lbs./13 kg
Tool Ratings — Maximum
Pipe Size Capacity
Model Pipe Material Notes
VE46S
VE46P
Steel
Stainless
Aluminum
PVC Plastic
2
Pipe Size (in
|
mm) / Schedule
3½
90
40
4
100
4½
120
5 – 40
40S Only
5 – 40
40 – 80
5
125
2 6061-T4 or 6063-T4 Alloy must be used.
* Ridgid is a registered trademark of the Ridge Tool Company.
6
150
VE26/46 Power Drive Kit
The VE26/46 power drive kit is available to allow both tools to be directly mounted to either a Victaulic VPD752 or Ridgid* 300 Power Drive.
Weight: 7lbs./3kg
Newer tools with serial numbers ending in “C” are compatible with the Power Drive
Kit. Tools which do not contain the “C” suffix will require retrofit to accept the Power
Drive Kit. Contact Victaulic for details.
* Ridgid is a registered trademark of the Ridge Tool Company.
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
5
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Field Portable
VE106/VE107
VE106/VE107 Groove-N-Go
• Mobile light-duty roll grooving tool with an integral motor/drive unit mounted to a portable hand truck
• Tool is operated using a standard 3 ⁄
8
"/9.5 mm square-drive ratchet
• Enhanced tracking rolls help to keep the pipe on the tool during the roll grooving process.
• Supplied with a standard tool box for accessory storage
• Completely self- contained unit with an integral motor, safety foot switch and power plug
• Roll grooves 1 ¼ – 6"/32 – 150 mm pipe
Power Requirements: VE106 works with 110 volt, 15 amp power connection.
VE107 works with 220 volt, 6 amp power connection.
Weight: 140 lbs./64 kg
Optional Accessories: Additional rolls/shafts are available for copper, lightwall stainless steel, and EndSeal (ES) grooving.
Tool Ratings — Maximum
Pipe Size Capacity
Model Pipe Material Notes
VE106/
VE107
Steel
Stainless
Lt. Wall SS
Copper
3, 4
3
5
6
1¼
32
1½
40
Pipe Size (in
|
mm) / Schedule
2
50
2½
60
3
80
3½
90
4
100
5 – 40
40S
5S – 10S
K, L, M and DWV
5
125
3 Use standard grooving rolls marked with the prefix R.
4 EndSeal ® grooving rolls marked with the prefix RZ are available. Contact Victaulic ® for details.
5 Use grooving rolls marked with the prefix RX.
6 Use grooving rolls marked with the prefix RR.
6
150
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
6
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Field Portable
VE206 Portable Roll Groover
• Tool head mounts to any tripod stand with a Ridgid* 300 bolt pattern or the flat bed of a work truck
• Hydraulic hand pump can be mounted on either side of the tool for right or left hand operation
• Supplied with victaulic tool carry bag for accessory storage
• Roll grooves 1 ¼ – 6"/32 – 150 mm pipe
Power Requirements: Compatible with multiple power drive units; Victaulic
VPD752, Ridgid* 300 or 700 and Rems Amigo II
Weight: 165 lbs./75 kg
VE206
Tool Ratings — Maximum
Pipe Size Capacity
Pipe Size (in
|
mm) / Schedule
Model
VE206
Pipe Material Notes
Steel
Stainless
Lt. Wall SS
Copper
3, 4
3
5
6
1¼
32
1½
40
2
50
* Ridgid is a registered trademark of the Ridge Tool Company.
2½
60
3
80
3½
90
4
100
5 – 40
40S
5S – 10S
K, L, M and DWV
5
125
3
Use standard grooving rolls marked with the prefix R.
4
EndSeal
®
grooving rolls marked with the prefix RZ are available. Contact Victaulic
®
for details.
5
Use grooving rolls marked with the prefix RX.
6
Use grooving rolls marked with the prefix RR.
6
150
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
7
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Field Portable
VE226
VE226 Portable Groover
• Mounts to a Victaulic VPD752 or Ridgid * 300 power drive
• Tool is operated using a standard 3⁄8"/9.5 mm square-drive ratchet
• Available in seven models for steel (and other IPS) pipe, copper tubing and stainless steel
• Roll grooves ¾ – 6"/20 – 150 mm pipe
Drive Requirements: Fits Victaulic VPD752 or Ridgid
*
300 power drives.
Optional bases for Ridgid* 535, 1224, 1822, and Oster 310 available.
Weight: 37 lbs./17 kg
Tool Ratings — Maximum
Pipe Size Capacity
Model Pipe Material Notes
VE226S
VE226B
VE226M
Steel
Stainless
Steel
Stainless
Aluminum
PVC Plastic
Steel
Stainless
VE226C Copper
VE226BSS Lt. Wall SS
VE226MSS Lt. Wall SS
VE226P
Aluminum
PVC Plastic
2
2
¾
20
40
1
25
1¼
5 – 40
40S Only
5 – 40
32
40– 80
5S – 10S
1½
40
2
50
5 – 40
40S Only
40– 80
2
6061-T4 or 6063-T4 Alloy must be used.
* Ridgid is a registered trademark of the Ridge Tool Company.
Pipe Size (in
|
mm) / Schedule
2½
60
5 – 40
3
80
3½
90
4
100
5 – 10
4½
120
5 – 40
40S Only
K, L, M and DWV
5S – 10S
40
5
125
5 – 10
5 – 10
6
150
VE226 Power Drive Kit
• Kit for connecting a VE226 roll grooving tool to a Ridgid* 700 power drive
Capacity: See appropriate tool
Weight: 75 lbs./34 kg
* Ridgid is a registered trademark of the Ridge Tool Company.
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
8
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Field Fabrication
VE272SFS
VE272SFS
• Portable roll groover mounts easily to the Victaulic VPD752 or Ridgid * 300 power drive
• Hydraulic hand pump operation with a unique pivot arm design reduces handle effort
• Enhanced tracking rolls help to keep the pipe on the tool during the roll grooving process
• Roll grooves ¾ – 12"/20 – 300 mm pipe
(Supplied with 2 – 12"/50 – 300 mm carbon steel roll sets)
Power Requirements: Victaulic VPD752 or Ridgid* 300 power drive
Weight: 184 lbs./84 kg
Optional Rolls: ¾"-1
1 /
2
"/20-40mm carbon and stainless steel rolls, Lt. wall stainless steel rolls ¾"-12"/20-300mm, EndSeal (ES), aluminum schedules 5-40
RP rolls, PVC plastic schedules 40-80 RP rolls, and copper RR rolls for type
K,L,M and DWV..
Optional Accessories: An optional pipe stabilizer for 8 – 12"/200 – 300 mm pipe is available and is required for copper.
Tool Ratings — Maximum
Pipe Size Capacity
Model
VE272SFS
Pipe Material Notes
Steel
Stainless
3, 4
3
Lt. Wall SS 5, 8
Aluminum 2, 7
PVC Plastic 7, 9
Copper 6, 8
¾
20
1
25
1¼
32
1½
40
Pipe Size (in
2
50
40
|
mm) / Schedule
2½
60
3
80
3½
90
4
100
5
125
5 – 40
40S
5S – 10S
5 – 40
40 – 80
K, L, M and DWV
6
150
8
200
40
10
250
12
300
5 – 20
.250
5 – 20
* Ridgid is a registered trademark of the Ridge Tool Company.
2 6061-T4 or 6063-T4 Alloy must be used.
3
Use standard grooving rolls marked with the prefix R.
4
EndSeal
®
grooving rolls marked with the prefix RZ are available. Contact Victaulic
®
for details.
5
Use grooving rolls marked with the prefix RX.
6 Use grooving rolls marked with the prefix RR.
7 Use grooving rolls marked with the prefix RP.
8 Use sway brace for 8”/200 mm copper and 8”-12”/200 – 300 mm lightwall stainless steel.
9 A special lower roll exclusively for grooving 2" Sch. 80 PVC is available. Part. No. RP02272L02
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
9
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Field Fabrication
VE416FS
VE416FS
• For field roll grooving of 2 – 16"/50 – 400 mm
• Groove depth adjuster allows for easy adjustment for initial groove diameter
• Hydraulic hand pump operation with a unique pivot arm design reduces handle effort
• Equipped with a pipe stabilizer for 6 – 16"/50 – 400 mm pipe sizes to control pipe sway
Power Requirements: Victaulic VPD752 or Ridgid* 300 power drive
Weight: 240 lbs./109 kg
Optional Rolls: Optional rolls are available for Schedule 5S and 10S stainless steel pipe, PVC and aluminum pipe, and type K, L, M and DWV copper tubing.
Pipe Size (in
|
mm) / Schedule
Tool Ratings — Maximum
Pipe Size Capacity
Model Pipe Material Notes
VE416FS
Steel 3, 4
Stainless
Lt. Wall SS
3
5
Aluminum 2, 7
PVC Plastic 7
Copper 6
2
50
40
2½
60
3
80
4
100
5 – 40
OGS
5
125
40S
5S – 10S
5 – 40
40 – 80
K, L, M and DWV
6
150
8
200
40
* Ridgid is a registered trademark of the Ridge Tool Company.
2 6061-T4 or 6063-T4 Alloy must be used.
3 Use standard grooving rolls marked with the prefix R.
4 EndSeal ® grooving rolls marked with the prefix RZ are available. Contact Victaulic ® for details.
5 Use grooving rolls marked with the prefix RX.
6
Use grooving rolls marked with the prefix RR.
7
Use grooving rolls marked with the prefix RP.
AGS
10
250
12
300
10 – STD
STD
14
350
16
400
STD Wall AGS
STD Wall RW AGS
10S RWX
5 – STD
This tool should not be used for field production grooving. For field production grooving capabilities, use a VE450FSD tool. VE416FS/FSD is designed for occasional field grooving of AGS pipe.
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
10
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Field Fabrication
VE270FSD/VE271FSD
VE270FSD/VE271FSD
• Completely self-contained unit with integral gear motor, safety guards, safety foot switch and power cord/plug
• Hydraulic hand pump operation with a unique pivot arm design reduces handle effort
• Enhanced tracking rolls help to keep the pipe on the tool during the roll grooving process
• Roll grooves ¾ – 12"/20 – 300 mm pipe
(Supplied with 2 – 12"/50 – 300 mm carbon steel roll sets)
Drive Requirements: Self-contained
Power Requirements: VE270FSD works with 110 volt, 15 amp power connection.
VE271FSD works with 220 volt, 6 amp power connection.
Weight: 340 lbs./154 kg
Optional Rolls:
3
/
4
"-1
1
/
2
"/20-40mm carbon and stainless steel rolls, Lt. wall stainless steel rolls
3
/
4
"-12"/20-300mm, EndSeal (ES), aluminum schedules 5-40
RP rolls, PVC plastic schedules 40-80 RP rolls, and copper RR rolls for type
K,L,M and DWV.
Optional Accessories: An optional pipe stabilizer for 8 – 12"/200 – 300 mm pipe is available and is required for copper.
Tool Ratings — Maximum
Pipe Size Capacity
Model Pipe Material Notes
VE270FSD/
VE271FSD
Steel
Stainless
2, 3
2
Lt. Wall SS 4, 13
Aluminum 1
PVC Plastic 6, 14
Copper 5, 13
¾
20
1
25
Pipe Size (in
1¼
32
1½
40
2
50
40
|
mm) / Schedule
2½
60
3
80
3½
90
4
100
5
125
5 – 40
40S
5S – 10S
5 – 40
40 – 80
K, L, M and DWV
6
150
8
200
40
10
250
12
300
5 – 20
.250
5 – 20
1 6061-T4 or 6063-T4 Alloy must be used.
2 Use standard grooving rolls marked with the prefix R.
3 EndSeal ® grooving rolls marked with the prefix RZ are available. Contact Victaulic ® for details.
4 Use grooving rolls marked with the prefix RX.
5
Use grooving rolls marked with the prefix RR.
6
Use grooving rolls marked with the prefix RP.
13 Use sway brace for 8”/200 mm copper and 8”-12”/200 – 300 mm lightwall stainless steel.
14 A special lower roll exclusively for grooving 2" Sch. 80 PVC is available. Part. No. RP02272L02
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
11
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Field Fabrication
VE416FSD/VE417FSD
VE416FSD/VE417FSD
• For field roll grooving of 2 – 16"/50 – 400 mm
• Groove depth adjuster allows for easy adjustment for initial groove diameter
• Completely self-contained units with integral gear motors, safety foot switch and power cord/plug
• Hydraulic hand pump operation with a unique pivot arm design reduces handle effort
• Equipped with a pipe stabilizer for 6 – 16"/150 – 400 mm pipe sizes to control pipe sway
Power Requirements: VE416FSD works with 110 volt, 15 amp power connection;
VE417FSD works with 220 volt, 8 amp power connection
Weight: 340 lbs./154 kg
Optional Rolls: Optional rolls are available for Schedule 5S and 10S stainless steel pipe, PVC and aluminum pipe, and type K, L, M and DWV copper tubing.
Pipe Size (in
|
mm) / Schedule
Tool Ratings — Maximum
Pipe Size Capacity
Model Pipe Material Notes
VE416FSD/
VE417FSD
Steel
Stainless
3, 4
3
Lt. Wall SS 5
Aluminum 2, 7
PVC Plastic
Copper
7
6
2
50
40
OGS
2½
60
3
80
4
100
5
125
5 – 40
40S
5S – 10S
5 – 40
40 – 80
K, L, M and DWV
6
150
8
200
40
AGS
10
250
12
300
14
350
16
400
10 – STD
STD
STD Wall AGS
STD Wall RW AGS
10S RWX
5 – STD
2
6061-T4 or 6063-T4 Alloy must be used.
3
Use standard grooving rolls marked with the prefix R.
4 EndSeal ® grooving rolls marked with the prefix RZ are available. Contact Victaulic ® for details.
5 Use grooving rolls marked with the prefix RX.
6 Use grooving rolls marked with the prefix RR.
7 Use grooving rolls marked with the prefix RP.
This tool should not be used for field production grooving. For field production grooving capabilities, use a VE450FSD tool. VE416FS/FSD is designed for occasional field grooving of AGS pipe.
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
12
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Field Fabrication
VE450FSD
VE450FSD
• Designed for field roll grooving of 4 – 24"/100 – 600 mm pipe
• Tool is supplied with carbon steel roll sets for grooving 4 – 12"/100 – 300 mm original groove and 14 – 24"/350 – 600 mm AGS groove on carbon steel pipe
• Enhanced tracking rolls help to keep the pipe on the tool during the roll grooving process, and quick change upper roll design
• Hydraulic hand pump operation with a unique pivot arm design reduces handle effort
• Features:
– Lifting point to move the tool with lifting equipment
– Frame can accept most fork lifts
– On board storage for tool accessories
Power Requirements: VE450FSD is a self-contained unit with two 220 volt, single phase 50/60 hz, 20 amp integral gear motors to handle heavier loads, safety foot switch and power cord/plug
Weight: 825 lbs./374 kg
Optional Rolls: Optional rolls are available for lightwall stainless steel original groove; 14 – 24/350 – 600 mm lightwall stainless steel AGS groove; and
4 – 12/100 – 400 mm EndSeal (ES) groove.
Tool Ratings —
Maximum Pipe
Size Capacity
Model
Pipe
Material Notes
4
100
VE450FSD
Steel
Stainless
Lt. Wall SS
Aluminum
PVC Plastic
3,10
11
12
2, 7
7
5
125
6
150
5 – 40
40S
5S – 10S
5 – 40
40 – 80 40
Pipe Size (in
OGS
STD
|
mm) / Schedule
8
200
10
250
12
300
5 –
STD
14
350
STD
16
400
18
450
14
350
AGS
16
400
18
450
20
500
22
550
24
600
5 – STD
STD
10S RWX
2 6061-T4 or 6063-T4 Alloy must be used.
3 EndSeal® grooving rolls marked with the prefix RZ are available. Contact Victaulic® for details.
7 Use grooving rolls marked with the prefix RP.
10 Use standard grooving rolls marked with the prefix R for both OGS and AGS.
11 Use standard grooving rolls marked with the prefix R for OGS and RW for AGS.
12
Use grooving rolls marked with the prefix RX for OGS and RWX for AGS. (Special RWX Rolls are available for
grooving true Sch. 10 (0.250 | 6.4 mm).
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
13
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Plant/Shop Fabrication
VE268
VE268
• Designed for fabrication shop roll grooving
• The fully-motorized, semi-automatic, electrohydraulic tool comes complete with safety guards and safety foot switch
• Equipped with a unique pivot arm design, making roll changes quick and easy, without removing shafts
• Enhanced tracking rolls help to keep the pipe on the tool during the roll grooving process
• Roll grooves ¾ – 12"/20 – 300 mm pipe (¾ – 1½"/20 – 32 mm rolls are optional)
Drive Requirements: Self-contained
Power Requirements: 220/440 volt, 3 phase, 60 hertz standard; the tool can also be supplied for use with various global voltage connections, contact Victaulic for details. 3 phase requires tool power to be hard wired by a local certified electrician. In Europe, this tool is fitted with a cable and 440V power plug prior to shipping.
Weight: 735 lbs./333 kg
Optional Rolls:
3 /
4
"-1 1 /
2
"/20-40mm carbon and stainless steel rolls, Lt. wall stainless steel rolls 3 /
4
"-12"/20-300mm, EndSeal (ES), aluminum schedules 5-40
RP rolls, PVC plastic schedules 40-80 RP rolls, and copper RR rolls for type
K,L,M and DWV.
Optional Accessories: An optional pipe stabilizer for 8 – 12"/200 – 300 mm pipe is available and is required for grooving 8"/200 mm copper tubing and Lt. Wall SS.
Tool Ratings — Maximum
Pipe Size Capacity
Model Pipe Material Notes
VE268
Steel
Stainless
3,4
3
Lt. Wall SS 5
Aluminum 2, 7
PVC Plastic 7, 9
Copper 6
¾
20
1
25
1¼
32
2
6061-T4 or 6063-T4 Alloy must be used.
3
Use standard grooving rolls marked with the prefix R.
1½
40
Pipe Size (in
|
mm) / Schedule
2
50
40
2½
60
3
80
3½
90
4
100
5
125
5 – 40
40S
5S – 10S
5 – 40
40 – 80
K, L, M and DWV
6
150
8
200
40
10
250
12
300
5 – 20
5 – 20
4 EndSeal ® grooving rolls marked with the prefix RZ are available. Contact Victaulic ® for details.
5 Use grooving rolls marked with the prefix RX.
6 Use grooving rolls marked with the prefix RR.
7 Use grooving rolls marked with the prefix RP.
9 A special lower roll exclusively for grooving 2" Sch. 80 PVC is available. Part. No. RP02272L02
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
14
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Plant/Shop Fabrication
VE414MC
VE414MC
• Designed for fabrication shop roll grooving Schedule 5, 10, and standard wall carbon steel pipe, standard wall stainless steel pipe, Schedule 40, 80
PVC pipe, and standard wall aluminum pipe
• Unique roll design, making roll changing quick and easy, without removing main shafts
• Enhanced tracking rolls help to keep the pipe on the tool during the roll grooving process
• The tool comes equipped with pipe stabilizers to provide smooth grooving operation
• Roll grooves 2 – 16"/50 – 400 mm pipe (Supplied with carbon steel
2 – 12"/50 – 300 mm original rolls and 14 – 16"/350 – 400 mm AGS rolls)
Drive Requirements: Self-contained
Power Requirements: 220/440 volt, 3 phase, 60 hertz standard; the tool can also be supplied for use with various global voltage connections, contact Victaulic for details. 3 phase requires tool power to be hard wired by a local certified electrician.
Weight: 735 lbs./333 kg
Optional Rolls: Optional rolls are available for Schedule 10S stainless steel pipe,
PVC and aluminum pipe, and type K, L, M and DWV copper tubing.
AGS roll sets for 14 – 16"/350 – 400 mm Schedule 10 through 0.375"/13 mm wall carbon steel pipe are now standard.
Tool requires modifications to groove AGS profile. Contact Victaulic for pricing and details.
Pipe Size (in
|
mm) / Schedule
Tool Ratings — Maximum
Pipe Size Capacity
Model Pipe Material Notes
VE414MC
Steel
Stainless
4, 10
11
Lt. Wall SS 12
Aluminum 2, 7
PVC Plastic
Copper
7
6
2
50
40
2½
60
3
80
4
100
40 – 80
OGS
5
125
5 – 40
40S
5S – 10S
5 – 40
K, L, M and DWV
6
150
8
200
40
10
250
AGS
12
300
14
350
16
400
10 – STD STD Wall AGS
STD Wall RW AGS
10S RWX
5 – STD
2 6061-T4 or 6063-T4 Alloy must be used.
4
EndSeal
®
grooving rolls marked with the prefix RZ are available. Contact Victaulic
®
for details.
6
Use grooving rolls marked with the prefix RR.
7 Use grooving rolls marked with the prefix RP.
10 Use standard grooving rolls marked with the prefix R for both OGS and AGS.
11 Use standard grooving rolls marked with the prefix R for OGS and RW for AGS.
12 Use grooving rolls marked with the prefix RX for OGS and RWX for AGS. (Special RWX Rolls are available for grooving true
Sch. 10 (0.250 | 6.4 mm).
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
15
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Plant/Shop Fabrication
VE460
VE460
• Fully-motorized, semi-automatic, hydraulic shop tool is shipped fully assembled with safety foot switch and rolls for standard grooving (4 – 24")
0.500 wall maximum.
• Enhanced tracking rolls help to keep the pipe on the tool during the roll grooving process
• Tool ships with 4 – 12” Original Groove System Groove Rolls and 14 – 24"
AGS Groove Rolls and 14 – 24" AGS Groove Rolls
Drive Requirements: Self-contained
Power Requirements: 220/440 volt, 3 phase, 60 hertz standard. The tool can also be supplied for use with various global voltage connections, contact
Victaulic for details. 3 phase requires tool power to be hard wired by a local certified electrician. In Europe this tool is fitted with a cable and 440V power plug prior to shipping.
Weight: 1500 lbs./680 kg
Optional Rolls: Grooving kits available to accommodate grooving 26"/650mm and above. Each support base is 12"/305 mm in height and corresponds with a range of allowable pipe sizes it can groove. See chart below for details.
AGS roll sets for 14 – 24"/350 – 900 mm Schedule 10 through 0.375"/13 mm wall carbon steel pipe are now standard.
Tool Ratings — Maximum
Pipe Size Capacity^
Model
VE460
Pipe Material Notes
Steel
Stainless
Lt. Wall SS
14
350
16
400
18
450
20
500
4, 11
11
10 – XS
12 5S – 10S, TRUE 10
STD
22
550
24
600
26
650
Pipe Size (in
|
mm) / Schedule
28
700
AGS
30
750
32
800
34
850
36
900
38
950
.375 – .500
40
1000
42
1050
48
1200
50
1250
60
1500
Tool Ratings — Maximum
Pipe Size Capacity
Model
VE460
Pipe Material Notes
Steel
Stainless
4, 11
11
Lt. Wall SS 12
Aluminum 2, 7
PVC Plastic 7
4
100
5
125
6
150
8
200
5 – 80
40S
40 – 80
5S – 10S
5 – 40
40
Pipe Size (in
|
mm) / Schedule
10
250
5 – XS
12
300
OGS
14
350
16
400
18
450
STD
5S – 10S, TRUE 10
20
500
22
550
24
600
2 6061-T4 or 6063-T4 Alloy must be used.
4 EndSeal ® grooving rolls marked with the prefix RZ are available. Contact Victaulic® for details.
7 Use grooving rolls marked with the prefix RP.
11 Use standard grooving rolls marked with the prefix R for OGS and RW for AGS.
12 Use grooving rolls marked with the prefix RX for OGS and RWX for AGS. (Special RWX Rolls are available for grooving true Sch. 10 (0.250 | 6.4 mm).
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
16
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Plant/Shop Fabrication
VE460 Pipe Stand Chart
VE460
Tool
Model
26 – 38"/
650 – 950 mm
Grooving Kit
LIFTING POINT
FRONT
LIFTING POINT
Roll Sets
Included
4 – 6"/
100 – 150 mm
8 – 12"/
200 – 300 mm
14 – 24"/
350 – 600 mm
Railing and
Platform
Kit Qy
N/A
Support
Base
(Qty/Part
No.)
Optional Accessories 17
N/A
Tool
Weight/
Shipping
Weight
Lbs.
1500/1750
Recommended
Pipe Stand
16
VAPS224
OR
VAPS1672
26 – 38"/
650 – 950 mm
1 1 N/A
VAPS236
OR
VAPS3036
OR
VAPS1672
40 – 48"/
1000 – 1200 mm
Grooving Kit
LIFTING POINT
LIFTING POINT
LIFTING POINT
FRONT
LIFTING POINT
FRONT
40 – 48"/
1000 – 1200 mm
1
14
2
15
N/A
VAPS1672
(R0001672PS)
50 – 60"/
1250 – 1500 mm
Grooving Kit
50 – 60"/
1250 – 1500 mm
1
14
3
15
N/A
VAPS1672
(R0001672PS)
LIFTING POINT
LIFTING POINT
LIFTING POINT
LIFTING POINT
FRONT
LIFTING POINT
FRONT
LIFTING POINT
FRONT
Optional Rolls: Optional rolls are available for Schedule 5S and 10S stainless steel pipe, PVC, and aluminum pipe.
14 Railing and Platform Kit is required only if preceding kit has not been ordered.
15 Only one (1) Support Base is required if preceding kit has been ordered.
16
For proper operation, a pipe stand is required. See Accessories for details.
17 Optional Accessory Kits list REQUIRED COMPONENTS to groove up to the specified size. Kit components
can be ordered individually or as a kit.
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
17
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Roll Grooving – Plant/Shop Fabrication
VE872
VE872
• Designed for fabrication shop grooving of larger carbon steel AGS grooves up to 72"/1800 mm
• The fully-motorized, semi-automatic, electrohydraulic tool comes complete with safety guards and safety foot switch
• Support bases are required to groove 30-inch/762-mm and larger pipe sizes
• Each support base is 16 inches/406 mm in height and corresponds with a range of allowable pipe sizes it can groove
Drive Requirements: Self-contained
Power Requirements: 220/440 volt, 3 phase, 60 hertz standard. The tool can also be supplied for use with various global voltage connections. 3 phase requires tool power to be hard wired by a local certified electrician. Contact
Victaulic for details.
Weight: 1900 lbs./862 kg
Tool Ratings — Maximum
Pipe Size Capacity
Model Pipe Material Note
8
200
10
250
12
300
14
350
16
400
18
450
20
500
Pipe Size (in
|
mm) / Schedule
22
550
24
600
26
650
28
700
30
750
32
800
34
850
36
900
38
950
40
1000
42
1050
48
1200
50
1250
54
1350
56
1400
60
1500
62
1550
72
1800
VE872 Carbon Steel
14 Sch. 40 .375/9.5 mm to .500/12.7 mm
14 Physical properties shall be in accordance with API specification 5L, Grades B, X42, X46, X52, X56 or X60, download publication 25.09.
For physical properties not listed contact Victaulic for details.
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
18
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Cut Grooving – Field Manual
VG
VG Vic-Groover
• Designed for manual or power cut grooving of a single size on steel, ductile, stainless steel, aluminum and PVC pipe
• Tools are supplied with a ratchet handle for manual operation
• Tools 2"/50 mm and larger are supplied with a power yoke
• Cut grooves ¾ – 8"/20 – 200 mm pipe
Drive Requirements: Manual or external drive, min. ½ hp./0.37 kw
Drive Speed: 40 rpm max.
Shipped Set For: Standard groove, IPS of size indicated or rigid/flexible for ductile/cast pipe
Weight: 28 lbs./13 kg
Vic-Groover Tool Capacity
Tool Ratings — Maximum Pipe Size
Capacity
Model
VG
Pipe Material
Steel
Stainless
Aluminum
1
PVC Plastic
Ductile Iron
¾
20
1
25
1¼
32
Pipe Size (in
|
mm) / Schedule
1½
40
2
50
2½
60
3
80
40 – 80
40 – 80
40 – 80
40 – 80
3½
90
4
100
Cl. 53
5
125
6
150
8
200
Class 53 Min.
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
19
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Cut Grooving – Field Fabrication
VG28GD
VG28GD
• Designed for cut grooving 2-8"/50-200 mm pipe
• A modified version (ABR) is available to groove and machine for rubber lining
Drive Requirements: External power drive
Drive Speed: 38 rpm max.
Shipped Set For: Standard groove 4 – 6"/100 – 150 mm steel pipe.
Weight: 37 lbs./17 kg
Pipe
Rubber Lining
Tool Bit Arm
Pipe Stop
Knife Profile for Abrasion Only*
Tool Ratings — Maximum Pipe
Size Capacity
Model Note Pipe Material
VG28GD 15
Steel
Stainless
Aluminum
Ductile Iron
2
50
Tool Ratings — Maximum Pipe Size
Capacity
Model
VG28GD-ABR
Note
15
Pipe
Material
Steel
2
50
2½
65
Pipe Size (in
|
mm) / Schedule
3
80
3½
90
4
100
40 – 80
40 – 80
40 – 80
Class 53 Min.
5
125
6
150
8
200
2½
65
Pipe Size (in
|
mm) / Schedule
3
80
3½
90
40 – 80
4
100
5
125
6
150
8
200
40
Pipe
VDG26GD
Tool Bit Arm
Pipe Stop
Knife Profile for Double groove Only*
VDG26GD
• Produces a 6"/150 mm double groove for specific use with Style 808 double groove couplings
Drive Requirements: External power drive
Drive Speed: 38 rpm max.
Weight: 37 lbs./17 kg
Tool Ratings — Maximum Pipe
Size Capacity
Model
VDG26GD
Note
15
Pipe
Material
Steel
2
50
15
Special knives and stops may be required
2½
65
Pipe Size (in
3
80
3½
90
NOTE: Victaulic Cut Grooving Tools require an external power source
(see Power Mule in Pipe Preparation Tool Accessories).
|
mm) / Schedule
4
100
5
125
6
150
40 – 80
8
200
*exaggerated for clarity
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
20
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Cut Grooving – Field Fabrication
VG26GD-COR
VG26GD-COR
• Designed specifically to cut groove carbon steel pipe to rubber line and machine for abrasion and corrosion resistance only
• Will cut groove carbon steel 2-6"/50-150mm
Drive Requirements: External power drive
Drive Speed: 38 rpm max.
Shipped Set For: Standard groove 4 – 6"/100 – 150 mm steel pipe.
Weight: 37 lbs./17 kg
Rubber Lining
Pipe
Pipe Stop
Tool Ratings — Maximum Pipe Size
Capacity
Model
VG26GD-COR
Note
15
Pipe
Material
Steel
2
50
2½
65
Pipe Size (in
|
mm) / Schedule
3
80
15
Special knives and stops may be required
NOTE: Victaulic Cut Grooving Tools require an external power source
(see Power Mule in Pipe Preparation Tool Accessories).
3½
90
40 – 80
4
100
5
125
6
150
Tool Bit Arm
Knife Profile for Abrasion and
Corrosion Only*
*exaggerated for clarity
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
21
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Cut Grooving – Field Fabrication
Pipe
VG824
Rubber Lining
Tool Bit Arm
Pipe Stop
Knife Profile for Abrasion Only*
VG824
• Will produce a single OGS cut groove for unlined piping systems
• The tool must be driven through its own integral gear box by an external power source
• Ideal for job site, fab shop or production cut grooving
• A modified version (ABR) is available to groove and machine for rubber lining
Drive Requirements: External power drive
Drive Speed: 38 rpm max.
Shipped Set For: Standard groove, 8 – 12"/200 – 300 mm steel pipe
Weight: 82 lbs./37.2 kg
Tool Ratings — Maximum Pipe
Size Capacity
Model
Note
Pipe
Material
VG824 15
Steel
Stainless
Aluminum
Ductile Iron
Pipe Size (in
|
mm) / Schedule
8
200
10
250
12
300
40 – 80
30 – STD
30 – STD
14
350
16
400
Class 53 Min.
18
450
20
500
30 – STD
22
550
24
600
Tool Ratings — Maximum Pipe
Size Capacity
Model
Note
VG824-ABR 15
Pipe
Material
Steel
8
200
10
250
Pipe Size (in
|
mm) / Schedule
12
300
14
350
16
400
40 – XS
18
450
20
500
22
550
24
600
Pipe
VG824DG
Pipe Stop
VG824DG
• Designed specifically for cutting a double groove on 8-12"/200-300mm pipe for use with Style 808 double groove couplings
• Ideal for job site, fab shop or production cut grooving
Tool Ratings — Maximum Pipe
Size Capacity
Model
Note
VG824DG 15
Pipe
Material
Steel
15
Special knives and stops may be required
Pipe Size (in
|
mm) / Schedule
8
200
10
250
40 – 80
12
300
14
350
16
400
18
450
20
500
22
550
24
600
Tool Bit Arm
Knife Profile for Double Groove Only*
*exaggerated for clarity
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
22
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Cut Grooving – Field Fabrication
Pipe
VG824-COR
Rubber Lining
Tool Bit Arm
Center
Stop
VG824-COR
• Designed specifically to cut groove carbon steel pipe to be rubber lined and machined for abrasion and corrosion resistance only
• The tool must be driven through its own integral gear box by an external power source at a maximum speed of 38 rpm
• Ideal for job site, fab shop or production cut grooving
• Cut grooves 8 – 24"/200 – 600 mm pipe
Drive Requirements: External power drive
Drive Speed: 38 rpm max.
Shipped Set For: Standard groove, 8 – 12"/200 – 300 mm steel pipe
Weight: 82 lbs./37.2 kg
Tool Ratings — Maximum Pipe
Size Capacity
Model
Note
VG824-COR 15
Pipe
Material
Steel
8
200
15
Special knives and stops may be required
10
250
Pipe Size (in
|
mm) / Schedule
12
300
14
350
16
400
40 – .500
18
450
20
500
22
550
24
600
Knife Profile for Abrasion and
Corrosion Only*
VG828
Pipe
Center Stop
Tool Bit Arm
Knife Profile for Abrasion and
Corrosion Only*
VG828
• VG828 will produce a single AGS cut groove
• Designed to be driven by the Power Mule II
Drive Requirements: External drive, min. 1½ hp
Drive Speed: 38 rpm max.
Weight: 82 lbs./37.2 kg
Tool Ratings — Maximum Pipe
Size Capacity
Model
VG828
Note
15
Pipe
Material
Steel
14
350
15 Special knives and stops may be required
Pipe Size (in
|
mm) / Schedule
16
400
18
450
20
500
.500-.750
22
550
24
600
*exaggerated for clarity
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
23
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Cut Grooving – Field Motorized
VG412
VG412 Orbital Machining Tool
• Complete modular pipe end preparation system providing quick, accurate cutting and grooving of ductile iron pipe to meet AWWA and other industry specifications for mechanical couplings
• External mounting and drive action is particularly suited to cement lined ductile iron pipe grooving
• The hinged frame design allows cutting at any point along the pipeline
• Blade setting and replacement is fast and easy
• Cut grooves 4 – 12"/100 – 300 mm pipe
• Safety foot switch
Drive Requirements: 120 volt/11.5 amp
Shipped Set For: Rigid radius groove profile, 4 – 12"/100 – 300 mm ductile iron pipe
Weight: 151 lbs./69 kg
Options: Capable of grooving 4 – 12"/100-300 mm IPS steel for closure piece grooving only.
NOTE: Specifically designed for field closure pieces. Not suitable for production grooving.
VG412 Tool Capacity
Tool Ratings — Maximum
Pipe Size Capacity
Model
VG412
Pipe
Material
Steel
Ductile Iron
4
100
Pipe Size (in
|
mm) / Schedule
4½
120
5
125
6
150
40 – 80
Class 53 Min.
8
200
10
250
12
300
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
24
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Plastic Groovers
VPG26 AND VPG824
• PVC plastic pipe requires a radius groove to reduce any point of stress concentration in this notch sensitive material
• Tools feature a high speed, router-type tool bit which cuts a radiused groove, to full depth, in one manual rotation of the tool around the pipe
VPG26
VPG824
VPG26
• Grooves 2 – 6"/50 – 150 mm pipe
Power Requirements: 110 volt, 1 phase, 60 Hz, 7 amps
Rotation Drive: Manual (clockwise)
Weight: 41 lbs./19 kg
Shipped Set For: VPG26 for 2 – 3 ½"/50 – 90 mm
VPG824
• Grooves 8 – 16"/200 – 400 mm pipe
Power Requirements: 110 volt, 1 phase, 60 Hz, 7 amps
Rotation Drive: Manual (Clockwise)
Weight: 47 lbs./21 kg
Shipped Set For: VPG824 for 8 – 12"/200 – 300 mm
Aquamine Grooving Tools
The APG is a manually operated tool used for producing a cut spline groove and beveled end on 4 - 12"/ 100 - 300 mm Aquamine pipe to prepare the pipe to receive an Aquamine coupling. It is an orbital tool which is rotated around a stationary, secured pipe. The tool may be operated on pipe held in a pipe vise or on supported in-place piping that is depressurized and drained.
Weight: 13.1 lbs./5.9kg
APG
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
25
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Hole Cutting Tools
HCT904
HCT908
VHCT900
VIC-TAP II
HCT904
• One piece cutting tool designed to cut holes up to 2 3/4"/70mm carbon and stainless steel pipe with OD up to 8"/200mm
• Allows for use of Mechanical-T, Vic-Let, and Vic-O-Well outlets
• This tool is only available in Europe
Capacity: 1 – 2 3/4"/25-70 mm holes for Mechanical-T, and Vic-Let connections
Power Requirements: 220 volt, 1 phase, 60 Hz, 10.0 amp
Weight: 23 lbs./10 kg
HCT908
• One-piece hole cutting tool designed to cut holes up to 4 ½/120 mm in carbon and stainless steel pipe with OD up to 8"/200mm
• Allows for use of Mechanical-T, Vic-Let, and Vic-O-Well outlets
Capacity: 1 – 4 ½"/25 – 120 mm holes for ½ – 4"/15 – 100 mm Mechanical-T, and Vic-Let connections
Power Requirements: 110 volt, 1 phase, 60 Hz, 7.0 amp
Weight: 23 lbs./10 kg
VHCT900
• Three-piece hole cutting tool designed to cut holes up to 3 ½"/90 mm in diameter for Mechanical-T, Vic-Let, and Vic-O-Well outlets
• Base unit clamps quickly onto the pipe in vertical, horizontal or overhead positions
• Heavy-duty drill mounts to the alignment guides and a manual feed assembly provides uniform pressure on the saw for maximum cutting efficiency
Capacity: 1 – 3½"/25 – 90 mm holes for ½ – 3"/15 – 80 mm Mechanical-T, Vic-
Let connections
Power Requirements: grounded 120 volt, 1 phase, 60 Hz, 10 amp electrical supply. (220 volt, 1 phase, 60 Hz, 5 amp available on request)
Weight: 36 lbs./16 kg
Accessories: Extended chain for 10 – 24"/250 – 600 mm pipe
VIC-TAP II
• Hole cutting tool designed for use with Style 931 Vic-Tap II Mechanical-T unit for tapping into steel pipe systems under pressures up to 500 psi/3450 kPa
Capacity: Vic-Tap II 4 – 8"/100 – 200 mm Run × 2½"/65 mm (IPS) Outlet
Power Requirements: 115 volt, 1 phase, 60 Hz, 7.5 amp
Weight:
(A) Drill guide base 15 lbs./6.8 kg
(B) Drill motor and feed assembly, total wgt. 16 lbs./7.3 kg
(C) Style 931/Valve unit, 12 lb./5.4 kg – 15 lb./6.8 kg, depending upon size
(4, 5, 6 and 8"/100, 125, 150 200 mm available)
Hole Size: 2
3 ⁄
8
"/60.5 mm
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
26
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Vic-Press Tool
PFT510
PFT510
• The Vic-Press Schedule 10S System requires a Vic-Press Schedule 10S tool designed for securing Vic-Press Schedule 10S products onto IPS Schedule
10S stainless steel pipe.
• Tool package include one (1) Vic-Press PFT510 tool, two (2) 18V Lithium
Ion batteries, one (1) battery charger, one (1) corded adapter, one (1) tool carrying case, one (1) jaw carrying case, one (1) ½"/15mm jaw, one
(1) ¾"/20mm jaw, one (1) 1"/25mm jaw, one (1) 1 ½"/40mm hinged jaw,
2"/50mm hinged jaw, and one (1) adapter jaw.
• Jaws are included with every tool purchase.
• Vic-Press PFT510 is designed for industrial and trade use only
Capacity: ½"/15mm, ¾"/20mm, 1"/25mm, 1½"/40mm, 2"/50mm Sch10S stainless steel pipe
Power Requirements: 110 volt/60 cycle/6.5 amp
Optional: 220 volt
Note: The Vic-Press Schedule 10S System is not compatible with PFT505 and/ or PFT509 tools/components. The Vic-Press Schedule 10S System requires the use of a Vic-Press PFT510 tool package.
Weight: PFT510 with 1"/25mm jaw 21 lbs./ 9.5kg
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
27
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Pipe Cutting Tools
VCT1
VCT1 Manual
• Lightweight and portable pipe cut-off tool handles 4 – 24"/100 – 600 mm pipe, up to 0.500/12.7 mm thick
• Worm gear drive crank handle provides smooth, manual travel, easy control and accurate cutting
Capacity: 4 – 24"/100 – 600 mm
Wall Thickness: 0.065 – 0.500"/1.65 – 12.7 mm (with tips supplied)
Tips: Acetylene – 1 ea. #00, #0, #1
Weight: 22 lbs./10 kg
VCT2
VCT2 Automatic
• Rotation is powered by a small 120 VAC motor with SCR remote control
• Unique distributor design has stainless steel insert which extends tip life, eases cleaning and reduces backfire
Capacity: 6 – 24"/150 – 600 mm
Wall Thickness: 0.065 – 0.500"/1.65 – 12.7 mm (with tips supplied)
Tips: Acetylene – 1 ea. #00, #0, #1
Speed Control: SCR
Power Required: 120 volt, 1 phase, 60 Hz, 15 amp
Motor Rating: 15 W 10,000 rpm
Weight: 33 lbs./15 kg
Accessories: Guide rail is sold separately. Recommended for pipe 12"/300 mm and above. Order Guide Rail D-600 for up to 24"/600 mm pipe (others available).
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
28
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Accessories – Power Drive
VPD752
VPD752
• Can be used as the power drive unit for the VE226, VE26, VE46, VE416FS and VE272SFS roll grooving tools, provided the tool is equipped with the correct base plate and the VG, VG28GD, and VG824 cut grooving tools with universal drive shaft
• Operated with a safety foot switch
Capacity: See appropriate tool
Power Requirements: 115 volts, 15 amp, 50/60 Hz (220 volt, 6 amp,
50/60Hz optional)
Weight: 140 lbs./634 kg
Optional: Universal drive shaft
Mule II
Power Mule II
• Ideal for driving individual Victaulic cut grooving tools
• Heavy-duty, two-wheeled unit drives Victaulic cut grooving tools at the speed and power necessary for accurate grooving
• Rotating head for horizontal and vertical applications
• Power Mule is equipped with a Forward-Off-Reverse control and integral foot switch
Capacity: Victaulic individual Vic-Groover tools – VG28GD, VG28GD-ABR,
VG26GD, VG26GD-COR, VG824, VG824-ABR, VG824-COR, VG824DG, VG828
Power Requirements: 115 volts, 15 amp 50/60Hz
Full Load Speed: 35 rpm
Weight: 190 lbs./86 kg
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
29
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Accessories – Adjustable Pipe Stand
VAPS112
VAPS112
• Designed for supporting pipe to be roll grooved
• Four adjustable legged portable self-standing unit
• Turnstile design allows pipe to be spun around for grooving of both pipe ends without dismounting pipe from stand
• Unique trough design allows for rotational and forward/traverse movement
Capacity:
3
/
4
– 12"/20 – 300 mm IPS pipe
Load Rating: 1075 lbs./490 kg
Vertical Stroke: 14
1 /
2
"/368 mm for adjusting rod, 8 1 /
2
"/216 mm leg adjustment,
23"/584 mm
Minimum Pipe Height from Floor: 23"/584 mm on 12"/300 mm pipe
21"/533 mm on 1"/25 mm pipe
Handle Effort Required to Raise 1075 lbs./490 kg Load: 50 lbs./23 kg maximum
VAPS224
VAPS1672
VAPS224
• Designed specifically for supporting pipe to be roll grooved
• Self-standing heavy-duty unit permits free pipe rotation and traversing on ball transfers
• Ball transfers are mounted in a manner permitting use of pipe slings
• Turnstile design allows pipe to be spun around for grooving of both pipe ends without dismounting pipe from stand
Capacity: 2 – 24"/50 – 600 mm IPS pipe
Load Rating: 1800 lbs./816 kg
Vertical Stroke: 23"/584 mm
Minimum Pipe Height from Floor: 13"/325 mm on 24"/600 mm IPS pipe
Maximum Pipe Height from Floor: 38"/965 mm on 2"/50 mm IPS pipe
Weight: 260 lbs./118 kg
Handle Effort Required to Raise 1800 lbs./817 kg Load: 50 lbs./23 kg maximum
VAPS1672
Vic-Easy Adjustable Pipe Stands are portable and self-standing units that permit free pipe rotation and traversing on ball transfers. They are designed for direct use with
Vic-Easy roll grooving tools.
Capacity: 16 – 72" pipe
Load Rating: 10000 lbs
Vertical Stroke: 17"
Minimum Pipe Height from Floor: 16" on 72" pipe
Maximum Pipe Height from Floor: 28" on 16" pipe
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
30
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Accessories – Pipe Diameter Tape
PT100A
PT101
PT100A / PT101
• Go/No-Go pocket-sized steel tapes are available for taking circumferential measurements on pipe sizes ¾ - 24".
• Tape contains Go/No-Go markings on one side for use with ¾ – 24" pipe in
ANSI B36.19 and many ISO-4200 sizes and is marked in 1/100th of an inch increments on the other side.
• The Go/No-Go side can be used to check cut or roll grooved pipe conformance to Victaulic original and Machined for Rubber Lining (ABR)
(¾ – 12") and Advanced Groove System (AGS) (14 – 24") groove diameter specifications.
• Tapes are notched on the lead end to allow proper overlap within the groove for more accurate measurement.
• The Go/No-Go side of the tape is not intended for use on sizes 76.1; 139.7;
165.1; 165.2; 216.3; 267.4; and 318.5 mm steel or stainless steel pipe sizes. For cast or ductile iron pipe sizes (up to 20"), copper tube sizes, and the steel and stainless steel pipe sizes listed above, use the side of the tape marked in 0.01" increments.
• The Go/No-Go pipe tape is a quick reference guide only. To ensure proper grooving dimensions, always refer to the I-100 Victaulic Field Installation
Handbook or to the latest groove specifications publications located on www.victaulic.com.
• Metric version, PT101, is also available for 20 - 600 mm pipe sizes.
PT102
PT102
• Go/No-Go pocket-sized steel tapes are available for taking circumferential measurements on pipe sizes 8 - 72"/200 - 1800 mm.
• Tape contains Go/No-Go markings on one side for use with Original Groove
System sizes 8 - 12"/200 - 300 mm pipe and Advanced Groove System sizes 14 - 72"/300 - 1800 mm pipe in ANSI B36.10/B36.19 and many
ISO-4200 sizes. In addition, the PT102 contains markings in 0.02"/0.5 mm increments on the opposite side.
• The opposite side of the diameter tape can be used to check Victaulic original groove specifications in 14 - 42"/200 - 1050 mm pipe sized, including China pipe sizes and JIS specifications 8 - 12"/200 - 300 mm pipe sizes.
• The Go/No-Go pipe tape is a quick reference guide only, it is not a replacement for a calibrated diameter measuring instrument. To ensure proper grooving dimensions, always refer to the I-PT102 Victaulic Go/No-Go
Pipe Diameter Tape Instructions Manual or to the latest groove specifications publications located on www.victaulic.com.
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
31
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Accessories – Fabrication Cell
VAP131- Fabrication Cell Package
• Turn-key, fab-shop solution
• Maximize productivity gains associated with Victaulic
®
grooved systems
• Comes standard with the VE460 shop tool, VAPS 131R pipe stand and track system, two VAPS 131F tables, VAPS 131T assembly table
VAP131
VAPS 131R Hydraulic
Adjustable Pipe Stand
VAPS 131F Hydraulic
Positioner
VAPS 131T Assembly Table
VAPS 131R HYDRAULIC ADJUSTABLE PIPE STAND
• Designed for supporting pipe to be roll grooved
• Permits free pipe rotation and traversing on ball transfers
• Turnstile design allows pipe to be spun around for grooving of both pipe ends without dismounting pipe from stand
Capacity: 4 – 24"/100 – 600 mm IPS pipe; load rating: 2000 lbs./907 kg
Vertical stroke: 30.5"/775 mm
Minimum pipe height from floor: Compatible with Victaulic
® production roll grooving tools
Power Requirements: 115 VAC
Weight: 500 lbs./227 kg
VAPS 131F HYDRAULIC POSITIONER
• Designed to support grooved pipe, valves, and fittings when used in conjunction with the VAPS 131T Assembly Table
• Foot control provided for hands-free operation
• Swivel caster wheel design for better mobility
Capacity: 4 – 24"/100 – 600 mm IPS pipe; load rating: 1200 lbs./544 kg with wheels installed, 2000 lbs./907 kg without wheels
Vertical stroke: 29.25"/743 mm
Power Requirements: 115 VAC
Weight: 400 lbs./181 kg
VAPS 131T ASSEMBLY TABLE
• Designed to support grooved pipe, valves, and fittings when used in conjunction with VAPS 131F Hydraulic Positioner
• Ball transfer assemblies can be positioned to accommodate pipe from 2 –
24"/50 – 600 mm
Capacity: 4 – 24"/100 – 600 mm IPS pipe; load rating: 8000 lbs./3629 kg, ball transfers load rating 700 lbs./318 kg
Vertical stroke: 29.25"/743 mm
Weight: 500 lbs./227 kg
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
32
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Accessories – Victaulic Bolted Split-Sleeve Products (VBSP) Closure Tools
CTM-01 Small Manual Tool
CTM-02 Large Manual Tool
CTM-01 Small Manual Tool
CTM-02 Large Manual Tool
• Offered in small and large sizes and is ideal for joining select VBSP couplings
• The tool brings the coupling housings together to allow the bolts and nuts to be installed
• For specific information on the appropriate tool by coupling, please download individual VBSP coupling product submittals
Weight: CTM-01 10lbs./4.5kg
CTM-02
CTH-01 SMALL 10-TON HYDRAULIC TOOL
CTH-02 LARGE 25-TON HYDRAULIC TOOL
• CTH-01 applies up to 10 tons of hydraulic force
• CTH-02 applies up to 25 tons of pressure and is designed for joining VBSP with a wall thickness of ¾"/19 mm or 1"/25.4 mm
• For specific information on the appropriate tool by coupling, please download individual VBSP coupling product submittals
Weight: CTH-01 55lbs./25kg
CTH-01 Small 10-Ton Hydraulic Tool
CTH-02 Large 25-Ton Hydraulic Tool
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
33
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Grooving Times
Time for pipe preparation obviously depends on widely varied factors including productivity, location, type, hardness, and wall thickness of pipe. As a gauge for typical grooving times, the following chart was prepared to include grooving time with pipe in position and tool properly set for the size and depth of groove. Times will be extended when going from one size to another for roll changes, depth stop setting, trial grooving and other minor adjustments incidental to changing pipe sizes or initial set-up time prior to the first production groove.
Approximate Grooving Time In Minutes – Steel Pipe
22
Nominal
Size
42
46
48
54
30
32
36
38
56
60
22
24
26
28
14
16
18
20
10
12
6
8
3 ½
4
4 ½
5
Inches
3/4
1
1 1/4
1½
2
2 ½
3
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.4
20 21
1.5
20 21
1.5
20 21
1.6
20 21
1.8
20 21
—
—
—
VE226
0.5
19
0.6
19
0.7
19 20
0.8
19 20
1.0
20 21
1.3
20 21
1.4
20 21
Roll Groovers – Powered
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.5
1.7
2.0
2.5
0.4
0.5
0.8
1.0
VE272SFS VE270FSD
— 0.2
—
—
0.2
0.2
—
0.3
0.3
0.4
0.2
0.3
0.3
0.4
1.2
1.5
1.8
2.3
0.4
0.4
0.6
0.8
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.8
0.9
1.5
1.8
0.4
0.5
0.6
0.8
VE268
0.2
0.2
0.2
0.2
0.3
0.3
0.4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
7.4
23
8.0
23
—
—
1.0
1.7
2.5
3.5
0.4
0.5
0.6
0.8
VE416FSD VE414MC
— —
—
—
—
—
—
0.3
0.3
0.4
—
0.2
0.2
0.2
0.3
0.4
0.6
0.7
0.2
0.2
0.2
0.2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
3.6
23
4.0
23
—
—
VE460
4.2
3.2
24
3.2
24
3.4
24
3
3.5
3.8
4
<1
1.1
1.4
2.7
<1
<1
<1
<1
3.6
24
4.0
24
4.2
24
4.5
24
4.8
24
5.0
24
5.5
24
5.8
24
6.5
24
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
3.0
4.0
—
—
1.7
1.9
2.3
2.5
Power
0.5
0.5
0.7
0.7
1.0
1.2
1.4
Vic-Groover
Cut Groovers
Vic-Adjustable
—
—
—
—
—
—
—
—
—
—
27.0
30.0
—
—
12.0
16.0
20.0
23.0
—
5.0
8.0
10.0
—
—
—
—
—
—
—
—
VG824
Power
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
10.0
15.0
—
—
5.5
7.0
8.0
9.0
2.5
3.0
3.8
4.5
Hand
1.5
1.5
2.0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
4.5
5.0
—
—
2.0
2.5
2.8
3.5
VG28GD
—
—
—
—
1.0
1.3
1.5
19 VE226B 20 VE226S 21 VE226M
22 For roll groovers the times apply to the thickest pipe wall for which the tool is rated. See tool capacities. For cut groovers, the times apply to standard wall steel pipe. For other materials and thicknesses contact Victaulic for details.
23
For AGS roll grooves
24 Based on 3/8"/10 mm wall thickness. For ½"/13 mm wall thickness add 10% to grooving times.
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
34
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Standard Pipe Wall Thickness
(ANSI B 36.10 & B 36.19 for Stainless Steel Pipe)
Actual
Outside
Diameter
8.625
219.1
10.750
273.0
12.750
323.8
14.000
355.6
4.000
101.6
4.500
114.3
5.563
141.3
6.625
168.3
1.900
48.3
2.375
60.3
2.875
73.0
3.500
88.9
Inches mm
1.050
26.9
1.315
33.7
1.660
42.4
16.000
406.4
18.000
457.0
20.000
508.0
24.000
610.0
26.000
660.4
28.000
711.0
Nominal
Size
8
200
10
250
12
300
14
350
3 ½
90
4
100
5
125
6
150
1 ½
40
2
50
2 ½
65
3
80
Inches mm
3/4
20
1
25
1 1/4
32
16
400
18
450
20
500
24
600
26
650
28
700
0.109
2.77
0.134
3.40
0.156
3.96
0.156
3.96
0.083
2.11
0.083
2.11
0.109
2.77
0.109
2.77
0.165
4.19
0.165
4.19
0.188
4.78
0.218
5.54
0.065
1.65
0.065
1.65
0.083
2.11
0.083
2.11
5S
0.065
1.65
0.065
1.65
0.065
1.65
—
—
—
—
—
—
0.083
2.11
0.083
2.11
0.109
2.77
0.109
2.77
0.109
2.77
0.134
3.40
0.156
3.96
0.065
1.65
0.065
1.65
0.083
2.11
0.083
2.11
5
0.065
1.65
0.065
1.65
0.065
1.65
—
—
—
Pipe Schedule/Wall Thickness – Inches/millimeters
0.148
3.76
0.165
4.19
0.180
4.57
0.188
4.78
0.120
3.05
0.120
3.05
0.134
3.40
0.134
3.40
0.188
4.78
0.188
4.78
0.218
5.54
0.250
6.35
0.109
2.77
0.109
2.77
0.120
3.05
0.120
3.05
10S
0.083
2.11
0.109
2.77
0.109
2.77
—
—
0.322
8.18
0.365
9.27
0.406
10.31
0.438
11.13
0.226
5.74
0.237
6.02
0.258
6.55
0.280
7.11
0.500
12.70
0.562
14.27
0.594
15.09
0.688
17.48
0.145
3.68
0.154
3.91
0.203
5.16
0.216
5.49
40
0.113
2.87
0.133
3.38
0.140
3.56
—
—
—
—
—
—
—
—
—
0.312
7.92
0.312
7.92
0.375
9.53
0.375
9.53
0.250
6.35
0.250
6.35
0.250
6.35
0.312
7.92
0.500
12.70
0.500
12.70
20
—
—
—
—
—
—
—
—
—
—
—
0.375
9.53
0.438
11.13
0.500
12.70
0.562
14.27
0.277
7.04
0.307
7.80
0.330
8.38
0.375
9.53
—
0.625
15.88
30
—
—
—
—
—
—
—
—
—
0.250
6.35
0.250
6.35
0.250
6.35
0.250
6.35
0.250
6.35
0.312
7.92
0.312
7.92
—
—
—
—
—
10
—
—
—
—
0.500
12.70
0.594
15.09
0.688
17.48
0.750
19.05
0.318
8.08
0.337
8.56
0.375
9.53
0.432
10.97
0.844
21.44
0.938
23.83
1.031
26.19
1.219
30.96
0.200
5.08
0.218
5.54
0.276
7.01
0.300
7.62
80
0.154
3.91
0.179
4.55
0.191
4.85
—
—
0.322
8.18
0.365
9.27
0.375
9.53
0.375
9.53
0.226
5.74
0.237
6.02
0.258
6.55
0.280
7.11
0.145
3.68
0.154
3.91
0.203
5.16
0.216
5.49
STD.
0.113
2.87
0.133
3.38
0.140
3.56
0.375
9.53
0.375
9.53
0.375
9.53
0.375
9.53
0.375
9.53
0.375
9.53
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
35
victaulic.com
| Pipe Preparation Tools | Publication 24.01
Standard Pipe Wall Thickness
(ANSI B 36.10 & B 36.19 for Stainless Steel Pipe)
48
54
42
46
Nominal
Size
Inches mm
30
750
32
800
36
900
36
38
56
60
72
Actual
Outside
Diameter
36.000
914.4
38.000
965.2
42.000
1066.8
46.000
1168.4
Inches mm
30.000
762.0
32.000
813.0
36.000
914.0
48.000
1219.2
54.000
1371.6
56.000
1422.4
60.000
1524.0
72.000
1828.8
—
—
—
—
—
5S
0.250
6.35
—
—
—
—
—
—
—
—
—
—
—
5
—
—
—
—
—
—
—
Pipe Schedule/Wall Thickness – Inches/millimeters
—
—
—
—
—
10
0.312
7.92
0.312
7.92
0.312
7.92
—
—
—
—
—
—
—
—
—
10S
0.312
7.92
—
—
—
—
—
—
20
0.500
12.70
0.500
12.70
0.500
12.70
—
—
—
—
—
—
—
—
—
—
—
—
—
—
30
0.625
15.88
0.625
15.88
0.625
15.88
—
—
—
—
+
+
+
+
40
—
0.688
17.48
0.750
19.05
+
+
+
+
+
—
—
0.375
9.52
0.375
9.52
—
STD.
0.375
9.53
0.375
9.53
0.375
9.53
—
—
—
—
+
+
+
+
0.5
12.70
0.5
12.70
+
80
—
—
—
+
+
Installation
Reference should always be made to the I-100 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our website at www.victaulic.com.
Warranty
Refer to the Warranty section of the current Price List or contact Victaulic for details.
Note
This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions.
Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations.
Trademarks
Victaulic is a registered trademark of Victaulic Company.
24.01 1629 Rev. O Updated 09/2014 © 2014 Victaulic Company. All rights reserved.
victaulic.com
36
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement