advertisement
10/100BASE-TX to 100BASE-FX
Fast Ethernet
Media Converter
Quick Installation Guide
FCC Class A Certification
This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
VCCI Class A Compliance (Japan)
This is a product of VCCI Class A Compliance
2
Introduction
Thank you for choosing the 10/100BASE Fast Ethernet
Media Converter, The Converter introduced here provides one channel media conversion between
10/100BASE-TX and 100BASE-FX.
About Media Converter
The Media Converter is a network technology specified by IEEE 802.3 10BASE-T, IEEE802.3u 100BASE-TX,
100BASE-FX standards.
3
Product Features
One-channel media conversion between
10/100BASE-TX and 100BASE-FX
Fiber media allows: multi-mode fiber using SC,ST,
LC or MT-RJ connector; single-mode fiber using
SC connector
Auto negotiation of speed and duplex mode on TX port
Auto MDI-X on TX port
One dip switch for configuring fixed half/full duplex modes on FX port
Store-and-forward mechanism
Back-pressure & IEEE802.3x compliant flow control
Full wire-speed forwarding rate
Front panel status LEDs
Used as a stand-alone device or with a chassis
Hot-swappable when used with a chassis
4
Installation
This chapter gives step-by-step installation instructions for the Converter.
Selecting a Site for the Equipment
As with any electric device, you should place the equipment where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference.
Specifically, the site you select should meet the following requirements:
1. The ambient temperature should be between 32 and 104 degrees Fahrenheit (0 to 40 degrees
2.
3.
Celsius).
The relative humidity should be less than 90 percent, non-condensing.
Surrounding electrical devices should not exceed the electromagnetic field (RFC) standards for
4.
5.
IEC 801-3, Level 2 (3V/M) field strength.
Make sure that the equipment receives adequate ventilation. Do not block the ventilation holes on each side of the switch or the fan exhaust port on the side or rear of the equipment.
The power outlet should be within 1.8 meters of the switch.
5
Connecting to Power
1. This Converter is a plug-and-play device.
2. Connect the supplied AC to DC power adaptor with a power voltage of 7.5Vdc/1.5Amp to the receptacle on the rear panel of the converter, and then attach the plug into a standard AC outlet with a voltage range from 100 to 260 Vac.
Dip Switch
There is a dip switch for duplex mode setting for fiber port. Refer to the table below for more details.
ON
1
Switch 1 : On -> Fiber Half Duplex
Off -> Fiber Full Duplex
On Half Off
6
Installing in a Chassis
The Converter can be fit into any of the expansion slots on a special designed chassis.
Unscrew and pull out the media converter board
First, install the converter onto a carrier supplied with the chassis:
Step 1- Unscrew the carrier from the desired expansion slot on the chassis.
Step 2- Remove the screw on the converter as shown below.
Step 3- Fit the converter onto the carrier and use the screw to secure it.
7
LED Indicator
The LED indicators give you instant feedback on status of the converter:
Power
(PWR)
100 Mbps
(100)
TX Port (TX)
FX Port (FX)
FDX/COL
TX Port (TX)
FX Port (FX)
LINK/ACT
Steady
Off
Runs at 100Mbps on TX port
Runs at 10Mbps on TX port
Steady
(FDX)
Connection in full duplex mode
FDX stands for FULL-DUPLEX
Lights off Connection in half duplex mode
Blinking
(COL)
Steady
(LINK)
Data collision
A valid network connection established
Lights off Not Linking
Blinking
(ACT)
Transmitting or receiving data
ACT stands for Activity
8
Specifications
Applicable
Standards
Fixed Ports
Speed
IEEE 802.3 10BASE-T
IEEE802.3u 100BASE-TX & 100BASE-FX
1 TX port, 1 FX port
10/20Mbps for half/full-duplex
100/200Mbps for half/full-duplex
Forwarding rate
LED Indicators
148,800pps
Cable
Dimensions
Per Unit- (2 LEDs): Power; Speed( 100 )
Per Port- (2 LEDs): FDX/COL, LINK/ACT
10BASE-T --
2-pair UTP Cat. 3,4,5, up to 100 m (328 ft)
100BASE-TX --
2-pair UTP Cat. 5, up to 100 m (328 ft)
100BASE-FX --
50/125μm or 62.5/125μm multi-mode fiber optic cable, up to 2 km
9/125μm or 10/125μm single-mode fiber optic cable, up to 100 km
L120 × W88 × H25 mm
300 g Weight
Power
Power
Consumption
Operating
Temperature
Storage
Temperature
Humidity
Emissions
External power adaptor 5V 1.5A or 5V/1A
1.8W Max.
0°C ~ 40°C (32°F ~ 104°F)
-25°C ~ 70°C (-13°F ~ 158°F)
10 ~ 90%, non-condensing
FCC part 15 Class A, CISPR ClassA, VCCI
Class A, CE Mark
9
Ordering Information
Please include the following information when ordering:
Fiber type: multi-mode or single-mode
Fiber connector type: SC,ST, LC or MT-RJ
Segment distance range for the fiber port
TX port
Connector
Type
RJ-45 Copper Wire Max. 100 m
FX port
Connector
Type
SC
ST
MT-RJ
LC
Multi-Mode Fiber
Multi-Mode Fiber
Multi-Mode Fiber
Multi-Mode Fiber
SC
SC
Single-Mode Fiber
Single-Mode Fiber
SC Single-Mode Fiber
SC Single-Mode Fiber
P/N:29071500M110SC0
Rev:E1-02
Max. 2 km
Max. 2 km
Max. 2 km
Max. 2 km
Max. 15 km
Max. 30 km
Max. 60 km
Max. 100 km
10
advertisement
Related manuals
advertisement