advertisement
PONY 20 SCA
IMPORTANT SAFETY INSTRUCTIONS
READ AND UNDERSTAND ALL INSTRUCTIONS
BEFORE OPERATING OR SERVICING MACHINE
DANGER!
Failure to Observe These Instructions Can Cause Personal Injury to Machine Operator, By-standers or Possible Machine Damage.
•
When using an electrical appliance, basic precautions should always be followed, including the following:
•
NEVER attempt to service or perform maintenance functions while the machine is plugged into an electrical outlet.
•
NEVER attempt to operate this machine unless you have been trained in its operation.
•
NEVER allow an untrained person to operate this machine.
•
Use this machine ONLY as described in this manual.
•
NEVER operate this machine with a damaged, broken, cut, abraded or taped cord or plug.
•
ALWAYS connect this machine to a properly grounded electrical outlet. See the following pages for grounding instructions and wiring diagram.
• NEVER leave this machine unattended when plugged in. Unplug the machine from the electrical outlet when not in use and before attempting repairs or maintenance.
• ALWAYS turn this machine OFF before unplugging from the electrical outlet.
•
NEVER operate this machine in the presence of flammable or combustible liquids, such as gasoline, fumes or dusts.
• NEVER attempt to pick up flammable or combustible liquids, such as gasoline, fumes or dusts.
•
NEVER handle the machine, cord, or plug with wet hands.
•
NEVER drop or insert any object into any machine opening.
•
ALWAYS keep face, fingers, hair or any body part, or loose clothing away from any machine opening or moving part.
•
NEVER pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
•
ALWAYS use extreme care when cleaning on stairs or when this machine is placed on stairs.
•
NEVER operate this machine if it is not working properly, if it has been dropped, damaged, exposed to weather or dropped into water. Return the machine to a service center for examination and repair.
•
NEVER operate this machine with any air opening blocked. Keep all air openings free of dust, lint, hair, and the like.
•
NEVER operate this machine without a dust bag and / or filters in place.
•
DO NOT pull or carry this machine by it’s electrical supply cord, use the cord as a handle, close a door on the cord, pull the cord around sharp edges or corners, expose to heated surfaces, or set heavy or sharp objects on the cord.
•
NEVER disconnect the plug by pulling on the cord. To disconnect the cord from the outlet, grasp the plug, not the cord.
•
DO NOT allow this machine to be used as a toy. Close attention is necessary when used by or near children.
•
DO NOT expose to rain, snow or extremes in temperature.
•
DO NOT use this machine to vacuum a floor or upholstery.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This machine must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for the electric current in order to reduce the risk of electric shock. This machine is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. FAILURE TO DO SO MAY CAUSE ELECTROCUTION due to improper connection of ground.
DANGER
Improper connection of the equipment grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the machine if it will not fit the outlet. Have a proper outlet installed by a qualified electrician.
This machine is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug illustrated in Figure A.
A temporary adapter that looks like the adapter illustrated in Figure B. may be used to connect this plug to a 2-pole receptacle as shown below if a properly grounded outlet is not available.
The temporary adapter should be used only until a properly grounded outlet (Figure A.) can be installed by a qualified electrician. The green colored rigid ear, lug, grounding clip or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a METAL screw.
Check the nameplate on the machine to be sure the voltage and cycle stated on the nameplate are the same as the voltage and cycle of the electrical outlet that you’re using. DO NOT attempt to plug a
115 volt machine into a 230 volt outlet.
Figure C. A machine that uses 230 volts may or may not have the grounding (earthed) plug attached to the cord. For use within the U.S.A. - 230 volts, 60 HZ , the plug is already supplied the with cord. For use outside the U.S.A., it may be up to the purchaser to have a proper grounding (earthed) plug attached.
Always use a properly grounded 3-wire extension cord which has male and female plugs. Use only
12-3 SJTWA type extension cords to a maximum length of 50 feet.
WIRING DIAGRAM
OPERATION AND INSTRUCTIONS
BASIC SAFETY PRECAUTIONS
It is always advisable to receive instructions from a person previously trained, however, if you are familiar with carpet cleaning, you should be able to operate this machine.
• Always be sure to read and fully understand all of these instructions before attempting to operate this machine.
• Never allow anyone to operate this machine who has not been properly trained.
• Refer to the complete safety and electrical warnings page.
MACHINE INSPECTION
• Carefully unpack this machine and recycle all packing materials.
• Inspect machine for damage or missing components. If damage is found, contact the freight company to file a freight claim.
NOTE
Always wear tennis shoes. Street shoes or rubber cushioned shoes, when wet, will release absorbed dirt or grease onto the carpeting and cause resoiling. Wet shoes can cause the operator to slip and fall when walking from wet carpet onto bare floors. Make sure the soles of your shoes are wiped dry before walking onto a bare floor. Care should be taken as carpet cleaning solutions may attack a bare floor.
CAUTION
• NEVER stick your hands, feet, or any other objects under the brush head when the motor is operating. Injury may result!
SPECIFICATIONS
General Machine Description
• This machine is a self propelled carpet extraction machine, and is available in both 115 volt and 240 volt configurations.
OPERATOR CONTROLS
Operator controls are positioned for ease of use, and include icons for simplified user training.
• Attach the twist lock end of the power cord to the stub cord of the machine, plug the other end into an appropriate electrical outlet. Move the speed control lever on the control panel to its slow speed. Turn
“ON” the master switch. Check to see if the top clear dome is secure on the recovery tank then turn the vac switch “ON” to make sure the vac motor is operating.
• To check on the brush and the pump for proper operation, turn both switches to “ON”. Squeeze the deadman lever under the control handle, the brush should run. With the solution tank empty, the solenoid that controls the pump should emit a short “bup-bup” sound.
OPERATION
•
Turn “ON” the master switch before turning “ON” the vacuum switch.
•
Turn “ON” the brush switch.
•
Turn “ON” the pump switch.
•
Lower the brush head assembly to the carpet with the left lift lever.
•
Lower the vacuum shoe to the carpet with the right lift lever.
Note: You may also “lockdown” the vacuum shoe to the carpet.
•
You must lift the vacuum shoe when moving this machine in reverse.
•
Squeeze the deadman lever under the control handle in order to propel forward, then turn on the brush and spray. The brush and spray will stop when the deadman lever is released.
•
At the cleaning site turn the speed control to propel the machine at the required speed.
•
You can drive the machine to the cleaning site by squeezing the deadman lever with the pump and vacuum switches “OFF”, and then turning the speed control to get the desired speed.
FEATURES
CONTROL PANEL
• The master switch, in the upper left corner, must be turned on before any other switch can be activated.
• The speed control is located just below the master switch, this knob controls the speed of the forward movement of the machine.
• On the right are three switches, from top to bottom they activate the spray, brush rotation, and suction.
• Below these switches are two circuit breakers, the left is for the brush motor, the right is for the drive motor.
SOLUTION
• The solution tank is the lower part of the machine body, with a capacity of 20 gallons. The tank is filled by pouring the water and cleaning chemicals through the cloth filter at the front of the tank, and dispensing through an in-line mesh filter screen at the solution tank outlet. The amount of fluid in the tank is visible via the clear hose at the back left of the machine. The tank may be drained by this hose by pulling down from the top. The solution pump is a 100 PSI continuous type, three piston bypass valve style.
RECOVERY TANK
• The recovery tank is the upper part of the machined body and has a capacity of 20 gallons. There is a metal screen cartridge on top of the vacuum tube under the clear dome. Turn the clear dome sideways to allow an opening in order to allow for the recovery tank and metal screen to air dry.
VACUUM MOTOR
• The vacuum motor is a three stage, 1 3/4 HP bypass style, with peripheral discharge. It is enclosed in a housing to reduce noise and improve cooling airflow.
GEAR DRIVE MOTOR
• This machine is propelled by a gear reduction motor through a chain and sprocket system. Variable speed is adjusted at the operator control panel.
BRUSH MOTOR / BRUSH ASSEMBLY
• The brush is driven by a 1/4 HP permanent magnet motor, via a cog belt and pulley system. The brush is a 22” wide nylon bristle, four-row chevron design. The brush housing assembly is a floating style.
SOLUTION SPRAY SYSTEM
• Solution is applied to the carpet through a spray bar assembly of five evenly spaced spray tips. The spray bar is easily serviced with the quick connect solution hose and quarter-turn removable spray tips. Positive shutoff of solution flow is controlled by an in-line solenoid.
ACCESSORY SPRAY WAND
• This is a standard feature that may be used to prespray a wide area of carpet before extraction. It may also be used to apply additional cleaning solution to trouble spots while extracting.
VACUUM SHOE
• The vacuum shoe is a 27” wide, weighted aluminum casting. Mounted with a bearing and a nylon bushing it is able to swing and swivel on a center arm. It is removable for cleaning or machine transportation by a quick disconnect mechanism. The intake of the vacuum shoe must be kept clean to ensure proper flow of extracted liquids. The rear cover plate may be removed to allow for a detailed interior cleaning.
BODY / CHASSIS
• This machine has a one year warranted rotocast poly body, mounted on a steel frame, which rides on two 8” diameter wheels, with grooved non-marking rubber treads and two 4” diameter swivel casters.
ACCESSORY SOLUTION OUTLET
• The quick connect accessory solution outlet, located at the rear of the machine and to the left (to which the accessory spray wand hose is connected), can be used to attach any of the accessory kits. Disconnect the quick connect that is attached to the accessory spray wand hose, and insert the solution hose which is part of any of the accessory kits. Solution from the solution tank is supplied to this outlet when the solution pump is “ON”, but will only dispense solution when the trigger of the upholstery, stair tool or jet wand is squeezed in the “ON” position.
SERVICE AND MAINTENANCE
REPAIR SERVICE
• Repair service for this machine must be performed by an authorized service center. Repair service performed by unauthorized service companies will void the machine warranty coverage.
• Turn off all switches and unplug this machine before beginning any service work.
OPERATOR CONTROL PANEL
• All operator controls are serviced by removing the screws securing the switch control panel to the body. This switch control panel will also allow access to the brush and vacuum shoe handle linkage. If the switches, circuit breaker and variable speed control malfunction, they are not repairable, and must be replaced with new factory parts. The power cord, switches and circuit breaker are checked for proper function by testing for continuity when in the “ON” position.
SOLUTION TANK
• To fill the solution tank make sure that the mesh filter is in place. Premix the extraction chemical (as per the chemical manufacturer’s mixing instructions) with hot water (95°F/35°C max.) in a five gallon bucket and pour it into the tank. High-foaming liquids waste the capacity of the recovery tank, always use a low-foaming extraction chemical.
• The mesh filter used to strain the solution poured into the solution tank should be removed after each use and rinsed in clear water before replacing.
• Clean solution must pass through an in-line mesh filter prior to entering the solution pump. This filter is mounted externally under the right / rear side of the solution tank (body). To remove the screen for cleaning you must first disconnect the hex nut of the solution hose, and then turn the lower half of the filter 1/8 of a turn counterclockwise.
• Remove the lower half of the filter, and mesh screen to clean.
CAUTION
If there is any clean solution in the tank it will drain out at this time. Reassemble and check for leaks.
RECOVERY
• Always use a defoamer to keep foam out of the vacuum motor fans. To efficiently defoam the recovered solution that will be vacuumed into the recovery tank, simply remove the vac hose from the vac shoe. Turn “ON” the vacuum switch; vacuum two cups of defoamer into the recovery tank. Do not put defoamer into the solution tank.
EMPTYING THE SOLUTION AND RECOVERY TANKS
• Any remaining solution should be drained into a toilet, slop sink, janitor’s closet, or bucket. If there is a small amount of solution left in the solution tank, it is possible to vacuum the solution into the recovery tank (provided there is sufficient room to handle the excess solution). It is necessary to turn the master switch and vacuum switch
“ON”, so that the vacuum motor is running.
• Remove the vac hose which is connected to the vac shoe. Pull the clear solution tank hose down, and insert it into the vac hose. The vac hose will vacuum the solution into the recovery tank. When the solution tank is empty turn the switches off. Remove the recovery tank hose from the bracket, clamp the hose with your hand and lower or aim the hose in the direction that you want the solution to flow. Turn the stopper counterclockwise and remove it, unclamp your hand and allow the solution to drain.
AFTER USE AND BEFORE STORAGE
• Both the solution and recovery tanks should be drained after each use. In addition, both tanks should be rinsed with clear water. Weekly flush out or clean the solution tank with a one gallon solution of 25% vinegar and warm water. Pour it into the solution tank, turn the machine “ON” and operate it to completely clean the tank, and the spray jets, (running for 30 seconds should be sufficient). This will remove any chemical residue. Failure to flush the solution system will result in poor spray patterns and corroded jet spray tips.
VACUUM MOTOR
• To service or replace the vacuum motor, you must remove the cooling air intake and the upper vacuum housing.
SOLUTION PUMP / SOLENOID
• The solution pump is mounted at the rear of the chassis, and is secured to a mounting plate by four screws.
• Eventually, the pump bypass valves may become weak or brittle during normal use (normal wear and tear), as a result of being attacked by chemicals used in the cleaning process. The result will be a drop in the pump output pressure.
SERVICE AND MAINTENANCE
• Pump pressure is restored by replacement of the bypass valve kit (part number 38-9-203-1) or by replacement of the pump (part no. 48-9-459-1, 115 volt, or 38-9-201-1, 240 volt).
• The electric solenoid provides a positive cutoff of solution flow to the spray jet bar assembly. The solenoid is activated (“ON”) when the deadman lever is lifted during operation.
MOTORS
The drive motor, vacuum motor, solution pump and solenoid are located inside the body of this machine.
To gain access to these components, you must complete the following procedures:
• Disconnect the power cord from the wall.
• Empty all liquids from the solution tank and recovery tanks.
• Disconnect the solution hose from the in-line solution filter, at the right side of the body.
• Remove the vacuum hose from the vacuum shoe. Disconnect the vacuum shoe lift cable from the cable bracket.
• Locate the mounting studs and nuts for the swivel casters. Remove only the rear / outer nuts. This will disconnect the rear of the main body from the chassis.
• Lift the rear of the machine body to tilt forward for access (the prop rod that holds up the machine, is under the solution tank).
DRIVE MOTOR / DRIVE CHAIN ADJUSTMENT
• The propulsion drive motor is mounted at the front of the chassis, and secured by four hex bolts. Access to this motor, and to the drive chain for chain tension adjustment and lubrication is from underneath the machine (at the front of the machine).
• The drive chain tension should be checked every 90 days and adjusted if necessary. To adjust the drive chain tension, you must first loosen the four hex bolts in the chassis slots under the propulsion motor. Slide the motor forward to decrease, or backward to increase the chain tension.
• The drive chain should be lubricated every 90 days with a penetrating moisture resistant lubricant, using a spray can with attachable straw to apply. DO NOT lubricate the chain when the machine is on a carpeted surface.
Wipe off any excess lubricant before operating the machine.
• The propulsion motor and gear box have no service parts, and must be replaced as a single unit.
BRUSH MOTOR / BRUSH ASSEMBLY / BELT
The brush motor, brush assembly and belt are serviced by removing both parts of the plastic two-piece brush housing cover.
• The brush drive belt tension is adjusted by first loosening the brush motor mounting hex nuts. Slide the motor toward the brush to decrease the tension, and away from the brush to increase the tension. When the motor is in the proper position, the drive belt should have 1/4” to 3/8” deflection midway between the motor and brush pulley.
• To replace the brush drive belt, you must remove the brush shaft mounting screw at the pulley end and loosen the screw at the opposite end. Install the new belt on the pulleys, replace and tighten the brush shaft mounting screws, and adjust the belt tension.
• Bristles will wear to the point where there is not enough agitation of the carpet. The nylon roller wheel can be raised to lower the brush deeper into the carpet. Remove the roller axle that attaches the roller wheel from its holding bracket, and reinstall the axle into the upper holes in the bracket.
WARNING
Do not use the upper roller axle position with a new or nearly new brush. This will force the brush to an exaggerated down position, overload the circuit breaker, and damage the brush drive motor.
• The brush motor is protected by a circuit breaker mounted on the control panel. The circuit breaker will open
(pop-up) when the brush motor is overloaded. When the circuit breaker “overloads” the stem will pop up to expose the white portion of the shaft. Unplug the machine. Prior to resetting the circuit breaker, you must inspect the brush assembly for obstructions such as foreign objects, strings around the brush shaft or “frozen” bearings.
• Reset the circuit breaker by pushing down on the stem until it “clicks” into the “ON” position.
SERVICE AND MAINTENANCE
• Adjustment or replacement of the brush assembly requires removing both brush shaft mounting screws, allowing the brush assembly to be removed from the housing. When installing the brush assembly, do not over tighten the shaft screws. This will prevent binding of the brush assembly.
• Replacement of the brush drive motor (no service parts avail.) requires the removal of the mounting hex nuts and wires to the rectifier and ground wire. Adjust the drive belt tension after replacing the motor.
SOLUTION SPRAY JET BAR
• Before attempting to operate the machine, it may be necessary to check the spray jets and see if they are clean. If the machine has been used previously, cleaning solution may have settled into the spray jets and dried, clogging them. Rinse them with warm water, or make a one gallon solution of 25% vinegar and warm water, and soak the jets for a few minutes to clean them. If an insoluble material is plugging the jets, use a wooden toothpick to clean the clogged jet. Do not use a knife or other sharp object - sharp objects will distort the spray pattern.
• In order to clean the spray jets, you must remove the spray jet bar from the brush housing. Disconnect the quick connect on the end of the solution hose from the quick connect on the spray jet bar. Simply pull out the spray jet bar from the brush head and reconnect the solution hose to the quick disconnect on the spray jet bar. Aim the spray jet bar at the carpet. Turn “ON” the master switch, then the spray pump. Turn the speed control to its slowest speed so the machine does not propel itself. Squeeze the deadman switch below the control handle of the machine. Solution will spray through the jets and onto the carpet, this will tell you if all the spray jets are clean. If one of the jets is not spraying, push in on the spray jet and turn it counterclockwise and remove it from the spray jet bar. Reattach by reinserting the tip and turning it clockwise.
If the solution pump does not supply solution at the spray jet bar due to an air lock in the solution hose, you must clear the solution hose in the following manor:
• Plug the machine into an electrical outlet.
• The solution tank should have liquid in it and the in-line filter screen should be clean.
• Turn “ON” the master switch and the spray switch.
• Stand at the side of the machine and depress the pin in the center of the accessory quick disconnect. The pump will push solution and air out of the quick connect. To purge the solution lines, run the pump for 30 seconds, or until the solution flows smoothly.
• Recheck the spray output at the spray jet bar assembly.
RAISING AND LOWERING THE VAC SHOE AND BRUSH HEAD
The vac shoe and power cord are packed in a separate carton with the machine. The vac shoe lift cable is already attached to the lift mechanism for the vac shoe.
• To attach the vac shoe, simply slide the tool onto the threaded rod and secure with a washer and nut, then slide the vac hose over the stock of the vac shoe. The vac shoe is now ready for operation.
• To lower the vac shoe to the carpet, move the right lever to the right and release.
• The vac shoe has an additional position to “lockdown” the vac shoe tighter to the carpet for better recovery. From the floating position push down on the right lever and lock it under the notch.
• To lower the brush head, move the left lever to the left, and release, the brush head will move into position on the carpet.
WHEELS / CASTERS/ INTERNAL COMPONENTS
• The 8” wheels have a clutch-type bearing. This style of bearing allows this machine to be pushed forward, without the use of the drive motor. When installed, the 8” wheel will rotate freely when turned toward the front of the machine (clockwise on the right - counterclockwise on the left).
• The swivel casters provide maneuverability and stable control of this machine. The swivel and wheel bearings must be lubricated on a regular basis to ensure trouble-free operation. You should use a non-water soluble grease for lubrication.
SERVICE AND MAINTENANCE
CLEANING HALLWAYS AND LARGE OPEN AREAS
To make the most efficient use of this machine, and to get the cleanest carpet, always vacuum the carpet, with a vacuum cleaner to remove excess dirt before scrubbing and extracting.
• Before attempting to clean the room or hallway, the operator should inspect the area to see if there are any heavy soil conditions (particularly heavy traffic areas) or spots. Propel this machine up to those areas and prespray.
• To prespray, remove the spray wand from it’s holder (located at the right, rear side of the machine).
• Prespray those traffic areas by squeezing the trigger on the spray wand. This will draw cleaning solution from the machine’s solution tank. Do not attempt to prespray areas that you will not overscrub with the machine within a ten minute time span.
• If there are spots, try to ascertain what type of stain it is. See the “Common Stains and Cleaning Treatments” page for solutions to use on the stain.
• There is room for two bottles of spotting liquid on the shelf at the back of the machine. Let the spray sit on the stain for about five minutes, then blot up as much as possible.
•
Plan your work based upon available electrical outlets.
•
The right hand side of the machine has a bumper wheel, so always keep the right side of the machine closest to the wall.
• Start at the electrical outlet to which your machine is plugged into, clean along the wall boards, away from your outlet. This helps to avoid running over the cord during operation.
• With the right-hand side of the machine closest to the wall, have the master switch, the pump motor, the vac motor, and the suction all “ON”, operate the machine as far as the cord will allow.
• It is possible to transverse 75 feet (the length of your cord) away from the wall outlet to which your machine is plugged in.
•
Usually, areas closest to the walls are the least soiled, the speed control can be set at its mid point, or turned up to a higher speed.
•
The brush shoe and brush head will swing out from the wall if they get too close to the wall. This avoids gouging the wall boards or the wall.
•
Cross to the other side of the hall or room and work your way back along the opposite wall for as far as the length of the cord will allow.
• It is best to allow for a two inch overlap on each pass to be sure you have covered all of the carpet.
•
If time allows after you have completed extracting, turn the spray switch “OFF”, then with both the vac switch and brush switches ”ON”, make high-speed passes over the carpet. The high-speed vacuuming of the extracted carpet will remove excess moisture, speed up the drying time, and set the pile, leaving a better appearance.
• Use an air mover dryer to speed up the drying time.
Note: If an extension cord must be used with this machine, limit it to 50 feet of 12-3 SJT.
ACCESSORY TOOLS
• 48-9-285-9
• 48-9-281-9
• 25-9-855-1
• 48-9-286-9
• 38-9-236-9
• 25-9-855-1
• 38-9-158-1
3” Upholstery Tool with Attachments
3” Upholstery Tool - 50 / 100 PSI
15’ x 1 1/2” Vac Hose with 1 1/2” Cuffs
3 - Jet Wand with Attachments
3 - Jet Wand 50 / 100 PSI
15’ X 1 1/2” Vac Hose with 1 1/2” Cuffs
15” X 3/8” Solution Hose with Male Connectors
TO ATTACH ACCESSORIES
Remove vac hose from vac shoe. Attach accessory vac hose cuff to machine vac hose. Remove spray wand water hose from machine body quick connect. Insert accessory water hose. Connect accessory vac hose and water hose to jet wand, or upholstery tool, or stair tool. To operate, turn on the master switch, pump, and vac switches. Squeeze the trigger on the wand, upholstery tool or stair tool to activate the spray.
134 49-9-190-1
135 91-2-121-0
136 31-9-020-6
137 49-9-191-1
138 91-2-160-0
139 91-2-160-0
140 91-2-140-0
141 49-9-278-1
142 49-9-001-1
143 88-9-110-0
144 48-9-020-9
145 48-9-267-1
146 49-9-114-1
147 48-9-267-1
148 48-9-029-2
149 91-2-104-0
150 91-2-097-0
151 48-9-166-3
152 91-2-097-0
153 91-2-104-0
154 49-9-278-1
155 38-9-040-1
156 48-9-028-1
157 49-9-111-1
158 48-9-089-1
159 49-9-100-3
160 48-9-032-1
161 48-9-144-1
162 91-2-043-0
163 48-9-144-1
164 48-9-032-1
165 48-9-030-3
166 48-9-031-1
167 48-9-013-9
168 49-9-037-3
169 48-9-011-1
170 49-9-063-1
171 48-9-028-1
172 48-9-181-1
ITEM PART NO.
101 49-9-278-1
102 49-9-278-1
103 49-9-019-1
104 49-9-278-1
105 49-9-101-1
49-9-164-9
106 49-9-002-1
107 48-9-089-9
108 48-9-090-1
109 49-9-115-1
110 25-9-922-1
111 27-9-188-1
112 23-9-216-1
113 23-9-166-6
114 27-9-562-1
115 48-9-025-1
116 48-9-267-1
117 49-9-022-1
118 49-9-277-1
119 87-9-103-0
120 23-9-214-1
121 49-9-112-1
122 49-9-123-1
123 49-9-124-1
124 49-9-052-1
125 49-9-050-1
126 48-9-265-1
127 49-9-051-1
128 49-9-278-1
49-9-278-1
129 91-2-089-0
130 91-2-093-0
131 44-9-062-1
132 91-2-139-0
133 91-2-202-0
PART DESCRIPTION
DEFOAMER LABEL - LABEL SET
FLAP LABEL - LABEL SET
CLEAR PLASTIC DOME
DOME INSTRUCTIONS LABEL - LABEL SET
DOME GASKET
DOME ASSEMBLY, INCLUDES ITEMS 101 TO 105
RECOVERY TANK
90 DEGREE ELBOW PVC - 1 1/2 FSL X 1 1/2 FPT - INCl. TUBE
TUBE
HOSE - VAC SHOE TO RECOVERY
END CUFF
PLUG STRAP
TUBE HOSE CLAMP - CRIMP ON TYPE
HOSE TUBE
DRAIN PLUG
DRAIN HOSE - RECOVERY TANK
HOSE CLAMP - 1 1/16" TO 2"
ELBOW - 3/4 MPT X 3/4 HOSE BARB
SOLUTION GAUGE
HOSE - SOLUTION TANK DRAIN
HOSE CLAMP - 11/16" TO 1 1/4"
DRAIN FITTING
DRAIN HOSE CLAMP
CLAMP, FILTER SOLUTION TANK
REDUCER - 1/2 MPT X 3/8 MPT NYLON
SOLUTION FILTER - 1/2 FPT X 1/2 MPT
HOSE CLAMP - 1/4" TO 13/16"
ELBOW - 1/2 FPT SWIVEL X 3/8 BARB
RIGHT SIDE LABEL - LABEL SET
LEFT SIDE LABEL - LABEL SET
1/4-20 HEX NUT WITH NY-LOK INSERT
9/32 I.D. X 5/8 O.D. X .051/.080 THICK FLAT WASHER (1/4)
3/8 SPRING WASHER
11/32 I.D. X 11/16 O.D. X .051/.080 THICK FLAT WASHER (5/16)
3/8 X 3/8 (5/16-18) SOCKET HEAD SHOULDER BOLT
LOWER PROP ROD
1/4-20 X 5/8 HEX BOLT
SPACER
UPPER PROP ROD
5/16-18 X 5/8 HEX BOLT
5/16 SPLIT LOCK WASHER
3/8 I.D. X 7/8 O.D. X .064/.104 THICK FLAT WASHER (5/16)
STRAIGHT SIDE LABEL - LABEL SET
SOLUTION TANK
1/2" X 1" GASKET
SOLUTION TANK FILTER
HOSE CLAMP - 1 1/16" TO 2"
HOSE - RECOVERY TANK TO VAC MOTOR
HOSE CLAMP - 1 1/16" TO 2"
HOSE BARB
1/4-20 X 5/8 ROUND HEAD PHILLIPS MACHINE SCREW
1/4 EXTERNAL STAR LOCK WASHER
HOLD DOWN BRACKET
1/4 EXTERNAL STAR LOCK WASHER
1/4-20 X 5/8 ROUND HEAD PHILLIPS MACHINE SCREW
NSS LOGO LABEL - LABEL SET
DRAIN VALVE GASKET
ADAPTER - 1 1/2 FSL X 1 1/2 MPT
RECOVERY TANK TUBE
ELBOW - 1 1/2 FSL X 1 1/2 FTT
FLOAT MOUNT BRACKET
FLOAT PIN
COTTER PIN
10-24 X 3/4 ROUND HEAD PHILLIPS MACHINE SCREW
COTTER PIN
FLOAT PIN
SHUT OFF PLATE
FLOAT ROD
FLOAT ASSEMBLY
FLOAT GUIDE
LINT SCREEN
VACUUM STACK
ADAPTER - 1 1/2 FSL X 1 1/2 MPT
“O” RING - 1 7/8 I.D. X 2 1/8 O.D.
1
1
1
1
1
1
1
1
1
1
1
2
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1 1/2 FT
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2.5 FT
1
1
1
1
1
1
1
1
1
1
QTY.
1
1
1
1
1
SOLUTION / RECOVERY TANKS
ITEM PART NO.
201 49-9-184-9
202 48-9-075-1
203 54-9-013-1
204 49-9-278-1
205 49-9-127-1
206 91-2-010-0
207 49-9-186-3
208 49-9-057-1
209 91-2-002-0
210 27-9-128-6
211 91-2-093-0
212 91-2-125-0
213 49-9-044-3
214 91-2-094-0
215 91-2-097-0
216 91-2-109-0
217 49-9-010-1
218 49-9-278-1
219 49-9-064-3
220 91-2-041-0
221 49-9-278-1
222 49-9-278-1
223 49-9-278-1
224 23-9-213-1
225 23-9-175-1
226 49-9-281-1
227 02-9-953-1
228 49-9-066-1
02-9-967-1
229 49-9-076-1
230 91-2-109-0
231 91-2-097-0
232 91-2-094-0
233 49-9-125-3
234 52-9-420-1
235 91-2-037-0
236 91-2-032-0
237 91-2-041-0
238 49-9-042-1
239 49-9-039-1
240 48-9-070-6
241 91-2-037-0
242 91-2-033-0
243 91-2-058-0
244 44-9-053-1
245 91-2-201-0
246 26-9-180-1
247 26-9-183-1
248 91-2-214-0
249 06-9-006-1
250 49-9-012-1
251 26-9-182-6
252 91-2-200-0
253 49-9-013-1
254 49-9-011-9
49-9-070-3
255 36-9-558-1
256 10-9-987-1
257 91-2-061-0
258 49-9-061-1
259 27-9-056-1
260 49-9-140-1
261 49-9-141-1
262 91-2-075-0
263 23-9-118-1
264 91-2-226-0
265 49-9-030-1
48-9-185-1
49-9-031-1
PART DESCRIPTION
MASTER POWER SWITCH, - 120 AND 240 VOLT
ROCKER SWITCH - SPRAY VACUUM BRUSH
KNOB WITH SET SCREW
SWITCH CONTROL PANEL LABEL - LABEL SET
LIMIT SWITCH, DEADMAN LEVER
6-32 X 1 ROUND HEAD PHILLIPS MACHINE SCREW
SWITCH CONTROL PANEL
SPEED CONTROL WITH KNOB - 120 AND 240 VOLT
6-32 HEX NUT WITH STAR LOCK WASHER
BUSHING SPACER
9/32 I.D. X 5/8 O.D. X .051/.080 THICK SAE FLAT WASHER (1/4)
1/4-20 X 3/4 HEX BOLT
DEADMAN LEVER
5/16 I.D. X 3/4 O.D. X .051/.080 THICK FLAT WASHER (1/4) (WROUGHT)
1/4 EXTERNAL STAR LOCK WASHER
1/4-20 X 1/2 TRUSS HEAD PHILLIPS MACHINE SCREW
CONTROL PANEL HOUSING
RAISE / LOWER BRUSH LABEL - LABEL SET
LIFT LEVER GUIDE PLATE
10-24 X 1/2 ROUND HEAD PHILLIPS MACHINE SCREW
RAISE / LOWER VAC SHOE LABEL - LABEL SET
WARNING LABEL - LABEL SET
GROUNDING LABEL - LABEL SET
HOSE CLIP
1/8 X 5/8 POP RIVET
STUB CORD WITH MALE TWIST LOCK PLUG, 120 VOLT
CORD STRAIN RELIEF
POWER CORD 75 FEET 120 VOLT
POWER CORD 16-3 SHUKO - 75 FEET 240 VOLT
LOWER REAR PANEL
1/4-20 X 1/2 TRUSS HEAD PHILLIPS MACHINE SCREW
1/4 EXTERNAL STAR LOCK WASHER
5/16 I.D. X 3/4 O.D. X .051/.080 THICK FLAT WASHER (1/4) (WROUGHT)
CLAMP BRACKET
NYLON CABLE CLAMP
7/32 I.D. X 1/2 O.D. X .032/.065 THICK SAE FLAT WASHER (#10)
#10 SPLIT LOCK WASHER
10-24 X 1/2 ROUND HEAD PHILLIPS MACHINE SCREW
BRUSH LIFT CABLE ADJUSTMENT BRACKET
LIFT CABLE BRUSH HOUSING
CABLE CLAMP
7/32 I.D. X 1/2 O.D. X .032/.065 THICK SAE FLAT WASHER (#10)
#10 EXTERNAL STAR LOCK WASHER
10-24 X 5/8 ROUND HEAD SLOT MACHINE SCREW
3/8 BALL JOINT
3/8-24 HEX NUT
LIFT ROD, MEDIUM
RETAINER
3/8-16 HEX NUT WITH NY-LOK INSERT
PIVOT SPACER
PRESSURE SPRING
SPRING HOUSING
3/8-16 HEX NUT
LIFT ROD, SHORT
VAC SHOE PRESSURE ROD ASSEMBLY
LIFT LEVER, VAC SHOE - BRUSH HOUSING
LIFT LEVER SPRING - BRUSH
.516 I.D. X .813 O.D. X .027/.030 THICK FLAT WASHER
10-24 HEX NUT WITH NY-LOK INSERT
LIFT LEVER PILOT
LIFT LEVER SPRING - VAC SHOE
CORD, CONNECTOR TO BASE COMPONENTS
CORD, SWITCH CONTROL PANEL TO CONNECTOR
10-32 X 1/2 TRUSS HEAD PHILLIPS MACHINE SCREW
LIFT LEVER GRIP
3/8-16 X 1 HEX BOLT
CIRCUIT BREAKER 3 AMP, 115 VOLT
CIRCUIT BREAKER 1 AMP, 115 AND 240 VOLT
CIRCUIT BREAKER 1.5 AMP, 240 VOLT
1
1
1
1
1
2
2
2
1
2
2
1
1
1
1
1
1
1
1
2
1
1
QTY.
1
3
1
2
1
1
1
1
1
2
4
2
2
2
2
8
1
1
2
4
1
2
1
2
2
1
1
1
1
1
1
2
1
2
1
1
2
1
1
4
1
1
1
1
1
1
1
CONTROL PANEL
266 91-2-002-0
267 91-2-210-0
268 91-2-226-0
269 91-2-036-0
270 02-9-966-1
271 08-9-113-1
272 50-9-243-1
273 91-2-094-0
274 91-2-097-0
275 91-2-109-0
276 91-2-041-0
277 91-2-032-0
278 91-2-037-0
6-32 HEX NUT WITH STAR LOCK WASHER
3/8 SPLIT LOCK WASHER
3/8-16 X 1 HEX BOLT
10-24 HEX NUT WITH STAR LOCK WASHER
STRAIN RELIEF CORD CLAMP
STRAIN RELIEF NUT, PLASTIC
#6 FLAT WASHER
5/16 I.D. X 3/4 O.D. X .051/.080 THICK FLAT WASHER (1/4) (WROUGHT)
1/4 EXTERNAL STAR LOCK WASHER
1/4-20 X 1/2 TRUSS HEAD PHILLIPS MACHINE SCREW
10-24 X 1/2 ROUND HEAD PHILLIPS MACHINE SCREW
#10 SPLIT LOCK WASHER
7/32 I.D. X 1/2 O.D. X .032/.065 THICK SAE FLAT WASHER (#10)
2
1
1
1
2
1
1
8
1
1
5
1
4
ITEM PART NO.
PART DESCRIPTION
301 49-9-018-1 BRUSH COVER, LONG
302 49-9-278-1 SPRAY BAR LABEL - LABEL SET
303 49-9-118-1 BRUSH COVER, SHORT
304 91-2-050-0 10-24 X 3/8 TRUSS HEAD PHILLIPS MACHINE SCREW
305 91-2-081-0 10 X 1/2 PAN HEAD PHILLIPS SHEET METAL SCREW
306 91-2-051-0 10-24 X 1/2 TRUSS HEAD PHILLIPS MACHINE SCREW
307 10-9-922-1 BEARING
308 49-9-008-6 THREAD GUARD
309 48-9-265-1 HOSE CLAMP, 3/4"
310 27-9-179-1 90° HOSE BARB 3/8 X 1/4 NPTM
311 49-9-129-1 MALE QUICK CONNECT
312 49-9-128-1 FEMALE QUICK CONNECT
313 38-9-114-1 1/4 ELBOW 90°
314 38-9-194-1 1/4 HEX NIPPLE, BRASS
315 91-2-089-0 1/4-20 HEX NUT WITH NY-LOK INSERT
316 49-9-193-2 ROLLER WHEEL
317 49-9-119-1 1/4-20 X 3 HEX BOLT (ROLLER AXLE)
318 91-2-097-0 1/4 EXTERNAL STAR LOCK WASHER
319 91-2-100-0 1/4-20 X 5/8 TRUSS HEAD PHILLIPS MACHINE SCREW
320 49-9-017-3 BRUSH HOUSING FRAME
321 49-9-117-1 3/8 X 3/4 (5/16-18) SOCKET HEAD SHOULDER SCREW
322 48-9-083-1 STRAIN RELIEF NUT
323 91-2-036-0 10-24 HEX NUT WITH STAR LOCK WASHER
324 91-2-043-0 10-24 X 3/4 ROUND HEAD PHILLIPS MACHINE SCREW
325 48-9-083-1 STRAIN RELIEF, INCLUDES NUT
326 49-9-068-1 BRUSH MOTOR POWER CORD
327 91-2-051-0 10-24 X 1/2 TRUSS HEAD PHILLIPS MACHINE SCREW
328 52-9-420-1 NYLON CABLE CLAMP
329 91-2-036-0 10-24 HEX NUT WITH STAR LOCK WASHER
330 49-9-024-1 ADJUSTING WHEEL SPRING
331 91-2-037-0 7/32 I.D. X 1/2 O.D. X .032/.065 THICK SAE FLAT WASHER (#10)
332 91-2-066-0 10-32 HEX NUT WITH STAR LOCK WASHER
333 49-9-153-1 BRUSH DRIVE MOTOR FAN, INCLUDES SET SCREW
334 91-2-065-0 10-32 X 3/4 SET SCREW - CUP POINT
335 49-9-049-1 BRUSH DRIVE MOTOR PULLEY
336 49-9-132-1 BRUSH DRIVE MOTOR, 120 VOLT
49-9-133-1 BRUSH DRIVE MOTOR, 240 VOLT
337 91-2-090-0 1/4-20 HEX NUT WITH NY-LOK INSERT
338 49-9-039-1 BRUSH HOUSING LIFT CABLE
339 49-9-042-1 BRUSH LIFT CABLE ADJUSTMENT BRACKET
340 54-9-274-1 RECTIFIER
341 91-2-036-0 10-24 HEX NUT WITH STAR LOCK WASHER
342 49-9-090-1 SPRAY TIP WITH BODY
49-9-091-1 SPRAY TIP ONLY (8001)
48-9-211-1 SPRAY TIP SEAL GASKET, “0” RING
48-9-129-1 BODY ONLY
343 49-9-048-1 BRUSH DRIVE BELT
344 49-9-004-1 SPRAY BAR
49-9-166-9 SPRAY BAR ASSEMBLY
345 23-9-215-1 1/4 PIPE PLUG
346 49-9-104-3 SPRAY BAR GUIDE
347 91-2-051-0 10-24 X 1/2 TRUSS HEAD PHILLIPS SCREW
348 49-9-007-1 BRUSH AXLE
349 49-9-142-1 RETAINING RING
350 49-9-005-1 BRUSH PULLEY
351 10-9-992-1 BEARING
352 34-9-049-1 RETAINING RING
353 49-9-142-1 RETAINING RING
354 91-2-067-0 10-32 X 5/8 FLAT HEAD PHILLIPS MACHINE SCREW
355 49-9-003-1 BRUSH ONLY
49-9-165-9 BRUSH ASSEMBLY
1
1
1
5
5
5
1
1
1
1
1
1
2
1
1
2
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
4
1
1
1
3
2
2
1
2
1
1
1
1
1
2
1
1
1
1
1
1
QTY.
1
1
1
3
1
2
BRUSH HOUSING
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
PART NO.
91-2-036-0
91-2-073-0
91-2-032-0
91-2-037-0
91-2-059-0
91-2-032-0
49-9-147-1
91-2-067-0
49-9-075-1
49-9-074-1
49-9-040-1
49-9-121-1
49-9-027-6
91-2-086-0
27-9-011-1
91-2-073-0
91-2-032-0
49-9-039-1
91-2-041-0
91-2-032-0
48-9-070-3
49-9-042-1
91-2-038-0
49-9-113-3
91-2-032-0
91-2-038-0
49-9-026-3
26-9-258-1
91-2-218-0
91-2-210-0
91-2-142-0
91-2-138-5
91-2-226-0
48-9-045-1
48-9-008-1
48-9-047-1
52-9-420-1
49-9-140-1
91-2-037-0
91-2-032-0
91-2-041-0
49-9-160-9
49-9-006-1
49-9-034-1
49-9-094-6
49-9-109-1
49-9-108-4
91-2-218-0
91-2-210-0
91-2-226-0
49-9-110-1
91-2-136-5
49-9-055-1
91-2-140-0
91-2-152-0
91-2-172-0
52-9-439-1
27-9-028-1
91-2-214-0
91-2-208-0
49-9-278-1
49-9-120-3
49-9-117-1
49-9-122-3
91-2-063-7
49-9-038-1
91-2-073-0
91-2-032-0
49-9-028-3
59-9-007-1
420
421
422
423
424
425
426
427
428
429
430
431
432
411
412
413
414
415
416
417
418
419
ITEM
401
402
403
404
405
406
407
408
409
410
433
434
435
436
437
438
439
440
441
442
PART DESCRIPTION
10-24 HEX NUT WITH STAR LOCK WASHER
10-32 X 1/2 PHILLIPS ROUND HEAD SCREW
#10 SPLIT LOCK WASHER
7/32 I.D. X 1/2 O.D. X .032/.065 THICK SAE FLAT WASHER (#10)
10-24 X 3/8 PAN HEAD PHILLIPS THREAD CUTTING SCREW
#10 SPLIT LOCK WASHER
VAC MOTOR GROUND WIRE
10-32 X 5/8 PHILLIPS FLAT HEAD SCREW
MASTER LINK
DRIVE CHAIN WITH MASTER LINK, 34 1/2 LINKS
SPROCKET, DRIVE AXLE, 18 TEETH
DRIVE AXLE KEY
DRIVE AXLE
1/4-20 X 3/8 SET SCREW
WIRE, KWIK CLIP
10-32 X 1/2 PHILLIPS ROUND HEAD SCREW
#10 SPLIT LOCK WASHER
BRUSH HOUSING LIFT CABLE
10-24 X 1/2 ROUND HEAD PHILLIPS MACHINE SCREW
#10 SPLIT LOCK WASHER
CABLE CLAMP
BRUSH LIFT CABLE ADJUSTMENT BRACKET
10-24 X 3/8 ROUND HEAD PHILLIPS MACHINE SCREW
AIR INTAKE SUPPORT
#10 SPLIT LOCK WASHER
10-24 X 3/8 ROUND HEAD PHILLIPS MACHINE SCREW
MAIN FRAME, CHASSIS
SWIVEL CASTER COMPLETE
13/32 I.D. X 13/16 O.D. X .051/.080 THICK WASHER (WROUGHT) (3/8)
3/8 SPLIT LOCK WASHER
5/16-18 HEX NUT
5/16-18 X 2 1/4 SET SCREW - CUP POINT
3/8-16 X 1 HEX BOLT
SNAP IN BUSHING
VAC INTAKE TUBE
GASKET, VAC INTAKE TO CHASSIS
NYLON CORD CLAMP
CORD, CONNECTOR TO BASE
7/32 I.D. X 1/2 O.D. X .032/.065 THICK SAE FLAT WASHER (#10)
#10 SPLIT LOCK WASHER
10-24 X 1/2 ROUND HEAD PHILLIPS MACHINE SCREW
DRIVE WHEEL ASSEMBLY WITH BEARINGS ONLY
8" WHEEL WITH GROOVES
BEARING, WHEEL, CLUTCH
BUSHING, WHEEL, PLATED
NYLON WASHER
THRUST WASHER
13/32 I.D. X 13/16 O.D. X .051/.080 THICK WASHER (WROUGHT) (3/8)
3/8 SPLIT LOCK WASHER
3/8-16 X 1 HEX BOLT
CURVED SPRING WASHER
1/4-28 X 1/4 SET SCREW
BEARING, DRIVE AXLE
3/8 I.D. X 7/8 O.D. X .064/.104 THICK FLAT WASHER (5/16)
5/16 SPLIT LOCK WASHER
5/16-18 X 1 1/4 HEX BOLT
AXLE SPACER, BUMPER WHEEL
BUMPER WHEEL
3/8-16 HEX NUT WITH NY-LOK INSERT
3/8-16 X 2 1/2 HEX BOLT
BUMPER BRACKET LABEL - LABEL SET
BUMPER WHEEL BRACKET
3/8 X 3/4 (5/16-18) SHOCKET HEAD SHOULDER SCREW
HINGE BRACKET
10-24 X 1/4 SET SCREW - CUP POINT
SPROCKET, GEAR DRIVE MOTOR, 12 TEETH
10-32 X 1/2 PHILLIPS ROUND HEAD SCREW
#10 SPLIT LOCK WASHER
MOUNTING BRACKET, GEAR DRIVE MOTOR
1/8 X 1/2 DRIVE MOTOR KEY
2
1
2
1
2
1
2
2
1
8
8
2
2
1
1
2
3
1
2
1
1
1
QTY.
6
6
2
6
1
3
1
1
1
1
2
2
6
2
2
2
2
2
4
2
2
4
2
1
2
1
1
2
1
1
1
1
1
1
6
5
1
1
4
4
2
1
1
1
2
1
1
1
CHASSIS
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
49-9-060-1
49-9-058-1
48-9-006-1
49-9-024-1
48-9-005-1
48-9-043-1
48-9-039-9
48-9-125-9
46-9-010-1
48-9-007-1
48-9-172-1
91-2-036-0
91-2-032-0
48-9-107-1
91-2-093-0
91-2-088-0
91-2-116-0
91-2-043-0
GEAR DRIVE MOTOR 120 VOLT
GEAR DRIVE MOTOR 240 VOLT
COOLING DUCT, VAC MOTOR
ADJUSTING WHEEL TENSION SPRING
VAC MOTOR SPLASH COVER
VAC MOTOR GASKET, UPPER
VAC MOTOR ASSEMBLY, 120 VOLT
VAC MOTOR ASSEMBLY, 240 VOLT
VAC MOTOR GASKET, LOWER
VAC MOTOR EXHAUST CHAMBER
GASKET, EXHAUST CHAMBER TO CHASSIS
10-24 HEX NUT WITH STAR LOCK WASHER
#10 SPLIT LOCK WASHER
HEYCO STRAIN RELIEF
9/32 I.D. X 5/8 O.D. X .051/.080 THICK SAE FLAT WASHER (1/4)
1/4 SPLIT LOCK WASHER
1/4-20 X 3/8 HEX BOLT
10-24 X 3/4 ROUND HEAD PHILLIPS MACHINE SCREW
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
522
523
524
525
526
515
516
517
518
519
520
521
527
528
529
530
ITEM
501
502
503
504
505
506
507
508
509
510
511
512
513
514
542
543
544
545
546
547
548
549
550
536
537
538
539
540
541
531
532
533
534
535
551
91-2-097-0
49-9-071-1
49-9-089-1
49-9-009-3
49-9-163-9
49-9-278-1
91-2-155-0
91-2-249-5
49-9-046-3
91-2-091-0
23-9-146-6
49-9-117-1
49-9-278-1
49-9-167-9
49-9-026-3
48-9-459-1
38-9-201-1
48-9-157-1
48-9-265-1
48-9-188-1
91-2-037-0
91-2-032-0
91-2-045-0
49-9-131-1
48-9-265-1
48-9-478-1
48-9-127-1
48-9-021-1
PART NO.
27-9-179-1
49-9-147-1
91-2-018-0
91-2-022-0
38-9-194-1
43-9-061-1
38-9-194-1
35-9-051-1
91-2-265-0
23-9-146-6
23-9-194-1
49-9-039-1
49-9-099-1
49-9-126-1
49-9-172-9
48-9-085-1
35-9-075-1
49-9-284-1
91-2-226-0
91-2-210-0
49-9-045-3
91-2-242-0
49-9-053-6
49-9-072-3
91-2-245-0
49-9-054-2
91-2-109-0
PART DESCRIPTION
90° HOSE BARB 3/8 X 1/4 NPTM
GROUND WIRE, SOLENOID VALVE
#8 INTERNAL STAR LOCK WASHER
8-32 X 3/8 ROUND HEAD PHILLIPS MACHINE SCREW
1/4 HEX NIPPLE, BRASS
1/4 NPT STREET “T”
1/4 HEX NIPPLE, BRASS
FEMALE QUICK CONNECT, ACCESSORY SOLUTION
1/2-13 X 2 1/14 HEX BOLT
PIVOT SPACER
BALL JOINT, VAC SHOE PIVOT
LIFT CABLE, BRUSH HOUSING
SPRAY TIP
ACCESSORY SPRAY GUN ONLY
ACCESSORY SPRAY GUN WITH HOSE
CORD CLAMP
MALE QUICK CONNECT, ACCESSORY SOLUTION
SOLUTION HOSE FOR SPRAY GUN
3/8-16 X 1 HEX BOLT
3/8 SPLIT LOCK WASHER
VAC SHOE LIFT BRACKET
1/2 SPLIT LOCK WASHER
VAC SHOE PIVOT ARM
COVER PLATE, VAC SHOE
17/32 I.D. X 1 1/16 O.D. X .047/.121 THICK SAE FLAT WASHER (1/2)
KNOB FOR VAC SHOE
1/4-20 X 1/2 TRUSS HEAD PHILLIPS MACHINE SCREW
1/4 EXTERNAL STAR LOCK WASHER
VAC SHOE GASKET
VAC SHOE WEIGHT
VAC SHOE CASTING
VAC SHOE ASSEMBLY
VAC SHOE DISCONNECT LABEL - LABEL SET
5/16 X 3/8 (1/4-20) SOCKET HEAD SHOULDER BOLT
1/2-13 THIN HEX NUT WITH NY-LOK INSERT
LIFT BRACKET SUPPORT
1/4-20 HEX NUT WITH STAR LOCK WASHER
PIVOT SPACER
3/8 X 3/4 (5/16-18) SOCKET HEAD SHOULDER BOLT
BRUSH COVER LABEL - LABEL SET
BRUSH HOUSING ASSEMBLY
MAIN FRAME, CHASSIS
SOLUTION PUMP 100 PSI, 120 VOLT
SOLUTION PUMP 100 PSI, 240 VOLT
SOLUTION HOSE, SOLUTION TANK TO PUMP
HOSE CLAMP 3/4"
90° HOSE BARB 3/8 NPTM
7/32 I.D. X 1/2 O.D. X .032/.065 THICK SAE FLAT WASHER (#10)
#10 SPLIT LOCK WASHER
10-24 X 1 ROUND HEAD PHILLIPS MACHINE SCREW
SOLUTION HOSE, SOLENOID TO SPRAY MANIFOLD
HOSE CLAMP 3/4"
SOLENOID VALVE 120 VOLT
SOLENOID VALVE 240 VOLT
BRASS BUSHING, 1/4F X 3/8 NPTM
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
11
1
2
1
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
QTY.
1
1
1
1
1
1
1
VAC SHOE
COMMON STAINS AND CLEANING TREATMENTS
TREATMENT METHODS
First: Remove excess material by blotting to absorb liquids, or by scraping with a dull edged (butter knife) if the material is a solid.
Second: Clean the remaining stain as directed by the chart below. Always follow the direction on the container. Apply the cleaning material directly to the stain (avoid over wetting the carpet or upholstery), then remove the loosened stain material with a white absorbent cloth or tissue.
Third: When the carpet is dry, gently brush the carpet pile to restore its appearance.
Note: Treat unknown stains with a volatile solvent first and follow with other agents as required. If you are uncertain of the effect of the cleaning agent on the carpet fiber or die test on an inconspicuous area first.
STAIN TYPE
Asphalt
Beer
Berry stain
Bleach
Blood (dried)
Blood (wet)
Butter
Catsup or Mustard
Chewing gum
Chocolate
Coffee
Cola drink
Creme de Menthe (green)
Egg (raw)
Food dye
Furniture dye or polish
Gravy
Lipstick
Mascara
Milk
Orange drink
Shoe polish
Tea
Tomato Juice
Urine
Vomit
Wine
TREATMENT MATERIAL
Volatile solvent/detergent
Liquid detergent, White vinegar
Liquid detergent, Ammonia 3-6%, Water
Liquid detergent, Water
Warm detergent, Ammonia 3-6%, Water
Liquid detergent, Water
Volatile solvent
Liquid detergent
Volatile solvent
Liquid detergent, Ammonia water
Detergent, White vinegar, Volatile solvent
Liquid detergent
Liquid detergent
Liquid detergent
Liquid detergent, Water
Paint/Oil/Grease remover, Detergent
Liquid detergent
Paint/Oil/Grease remover
Paint remover, Volatile solvent, Detergent, Water
Liquid detergent
Liquid detergent, Water
Heated iron into clean towel, Volatile solvent
Liquid detergent
Liquid detergent
Liquid detergent, Water
Warm detergent, Water, White vinegar
Liquid detergent, Ammonia 3-6%, Water, Vinegar
NSS ® Enterprises, Inc.
3115 Frenchmens Road, Toledo, Ohio 43607
PHONE (419) 531-3761 FAX (419) 531-3761
NSS ® Enterprises, Inc. European Distribution Centre
Unit II, Pinfold Trading Estate * 55 Nottingham Road
STAPLEFORD, NOTTINGHAM NG9 8AD ENGLAND U.K.
PHONE: (44) 0115 939 1568 * FAX: (44) 0115 949 0615
PONY 20 SCA ORIG. 07-97 REV A 08-00 9094906
advertisement
Related manuals
advertisement