User's manual | Biostar 945GC MICRO 775 User`s manual

945GC-M7 SE / 945GC Micro 775

Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ........................................ 1

1.1

1.2

1.3

1.4

1.5

1.6

1.7

Before You Start ................................................................................ 1

Package Checklist ............................................................................. 1

Motherboard Features...................................................................... 2

Rear Panel Connectors (for Ver 6.x)............................................... 4

Rear Panel Connectors (for Ver 5.x)............................................... 4

Motherboard Layout (for 945GC-M7 SE)....................................... 5

Motherboard Layout (for 945GC Micro 775)................................. 6

Chapter 2: Hardware Installation........................... 7

2.1

2.2

2.3

2.4

Installing Central Processing Unit (CPU)....................................... 7

FAN Headers...................................................................................... 9

Installing System Memory.............................................................. 10

Connectors and Slots ....................................................................... 12

Chapter 3: Headers & Jumpers Setup ................... 14

3.1

3.2

How to Setup Jumpers .................................................................... 14

Detail Settings.................................................................................. 14

Chapter 4: Useful Help......................................... 21

4.1

4.2

4.3

4.4

Driver Installation Note.................................................................. 21

Award BIOS Beep Code .................................................................. 22

Extra Information............................................................................ 22

Troubleshooting............................................................................... 24

Chapter 5: WarpSpeeder™ III ............................. 25

5.1

5.2

5.3

5.4

Introduction...................................................................................... 25

System Requirement ....................................................................... 25

Installation ....................................................................................... 26

WarpSpeeder™ III............................................................................. 27

Appendencies: SPEC In Other Language .............. 32

German.................................................................................................................. 32

France .................................................................................................................... 34

Italian..................................................................................................................... 36

Spanish ................................................................................................................... 38

Portuguese ............................................................................................................ 40

Polish...................................................................................................................... 42

Russian ................................................................................................................... 44

Arabic..................................................................................................................... 46

Japanese ................................................................................................................ 48

945GC-M7 SE / 945GC Micro 775

CHAPTER 1: INTRODUCTION

1.1 B

EFORE

Y

OU

S

TART

Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below:

Prepare a dry and stable working environment with sufficient lighting.

Always disconnect the computer from power outlet before operation.

Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge.

Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board.

Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment.

Keep the computer from dangerous area, such as heat source, humid air and water.

1.2 P

ACKAGE

C

HECKLIST

HDD Cable X 1

Rear I/O Panel for ATX Case X 1

User’s Manual X 1

Fully Setup Driver CD X 1

Serial ATA Cable X 1

FDD Cable X 1 (optional)

Serial ATA Power Cable X 1 (optional)

USB 2.0 Cable X1 (optional)

S/PDIF out Cable X 1 (optional)

1

Motherboard Manual

1.3 M

OTHERBOARD

F

EATURES

945GC-M7 SE 945GC Micro 775

LGA 775

Intel Core2Duo / Pentium 4 / Pentium D /

LGA 775


Celeron D processor up to 3.8 GHz Celeron D processor up to 3.8 GHz

*It is recommended to use processors with 95W *It is recommended to use processors with 95W

CPU power consumption.

Supports Hyper-Threading

Execute Disable Bit

Enhanced Intel SpeedStep

Extended Memory 64 Technology power consumption.

Supports Hyper-Threading

Execute Disable Bit

Enhanced Intel SpeedStep

Extended Memory 64 Technology

FSB

Chipset

Graphics

Super I/O

Main

Memory

IDE

SATA

LAN

533 / 800 / 1066 MHz

Intel 945GC

Intel ICH7

Intel GMA 950

Max Shared Video Memory is 224MB

533 / 800 / 1066 MHz

Intel 945GC

Intel ICH7

Intel GMA 950

Max Shared Video Memory is 224MB

ITE IT8712F

H/W Monitor

Fan Speed Controller

ITE's "Smart Guardian" function

ITE IT8712F

H/W Monitor

Fan Speed Controller

ITE's "Smart Guardian" function

DIMM Slots x 2

Each DIMM supports 256/512MB & 1GB DDR2

DIMM Slots x 2

Each DIMM supports 256/512MB & 1GB DDR2

Max Memory Capacity 2GB

Dual Channel Mode DDR2 memory module

Supports DDR2 400 / 533 / 667

Max Memory Capacity 2GB

Dual Channel Mode DDR2 memory module

Supports DDR2 400 / 533 / 667

Registered DIMM and ECC DIMM is not supported

Integrated IDE Controller

Ultra DMA 33 / 66 / 100 Bus Master Mode supports PIO Mode 0~4,

Integrated Serial ATA Controller

Data transfer rates up to 3.0 Gb/s.

SATA Version 2.0 specification compliant.

Registered DIMM and ECC DIMM is not supported

Integrated IDE Controller

Ultra DMA 33 / 66 / 100 Bus Master Mode supports PIO Mode 0~4,

Integrated Serial ATA Controller

Data transfer rates up to 3.0 Gb/s.

SATA Version 2.0 specification compliant.

Realtek RTL 8100C / 8110SC (optional) Realtek RTL 8100C / 8110SC (optional)

10 / 100 Mb/s / 1Gb/s auto negotiation (Gigabit 10 / 100 Mb/s / 1Gb/s auto negotiation (Gigabit

2

Sound

Codec

945GC-M7 SE bandwidth is for RTL 8110SC only)

Half / Full duplex capability

ALC662(Ver 6.x)

5.1 channels audio out (Ver 6.x)

High-Definition Audio support

Slots

On Board

Connector

PCI Express x16 slot

PCI Express x1 slot

PCI slot

Floppy connector

IDE Connector

Printer Port Connector

SATA Connector

Front Panel Connector

Front Audio Connector

CD-in Connector

S/PDIF out connector

CPU Fan header

System Fan header

Clear CMOS header

USB connector

Power Connector (24pin)


PS/2 Keyboard

PS/2 Mouse

Back Panel

Serial Port

VGA port

I/O

LAN port

USB Port

Audio Jack (Ver 6.x) x1 x1 x2 x1 x1 x1 x2 x1 x1 x1 x1 x1 x1 x1 x1 x1 x4 x1 x4 x3 x1 x1 x1 x1

Board Size 219 (W) x 235 (L) mm

Windows 2000 / XP / VISTA

OS Support Biostar Reserves the right to add or remove support for any OS with or without notice.

945GC-M7 SE / 945GC Micro 775

945GC Micro 775 bandwidth is for RTL 8110SC only)


ALC861VD(Ver 6.x) / ALC888(Ver 5.x)



High-Definition Audio support

PCI Express x16 slot

PCI Express x1 slot

PCI slot x1 x1 x2

Floppy connector

IDE Connector

Printer Port Connector

SATA Connector

Front Panel Connector

Front Audio Connector

CD-in Connector

S/PDIF out connector

CPU Fan header

System Fan header

Clear CMOS header

USB connector


Power Connector (4pin) x1 x1 x1 x2 x1 x1 x1 x1 x1 x1 x1 x1 x1 x4

PS/2 Keyboard

PS/2 Mouse

Serial Port

VGA port

LAN port

USB Port

Audio Jack (Ver 6.x)

Audio Jack (Ver 5.x)

219 (W) x 235 (L) mm


Biostar Reserves the right to add or remove support for any OS with or without notice. x1 x4 x3 x6 x1 x1 x1 x1

3


1.4 R

EAR

P

ANEL

C

ONNECTORS

(

FOR

V

ER

6.

X

)

PS/2

Mouse LAN

Line In/

Surround

Line Out

Mic In 1/

Bass/ Center

PS/2

Keyboard

COM1 VGA1 USBX2 USBX2

1.5 R

EAR

P

ANEL

C

ONNECTORS

(

FOR

V

ER

5.

X

)

PS/2

Mouse LAN

4

PS/2

Keyboard

COM1 VGA1 USBX2 USBX2

Center

Rear

Line In

Line Out

Side Mic In

Since the audio chip supports High Definition Audio Specification, the function of each audio jack can be defined by software. The input / output function of each audio jack listed above represents the default setting. However, when connecting external microphone to the audio port, please use the Line In (blue) and Mic In (Pink) audio jack.

945GC-M7 SE / 945GC Micro 775

1.6 M

OTHERBOARD

L

AYOUT

(

FOR

945GC-M7 SE)

JKBMS1

JATXPWR2

LGA775

CPU1

JATXPWR1

JPRNT1

JUSB2

JCFAN1

JRJ45USB1

JAUDIO1

JAUDIOF1

Super

I/O

PEX16_1

Codec

LAN

JCDIN1

PEX1_1 BIOS

JSPDIF_OUT

PCI1

PCI2

Intel

945GC

Intel

ICH7

JUSB3 JUSB4

Note: ■ represents the 1 st pin.

JCMOS1

BAT1

SATA3 SATA1

JSFAN1

SATA4 SATA2

JPANEL1

5


1.7 M

OTHERBOARD

L

AYOUT

(

FOR

945GC M

ICRO

775)

JKBMS1

JATXPWR2

LGA775

JKBV1

CPU1

JATXPWR1

JPRNT1

JUSB2 JUSBV1

JRJ45USB1

JCFAN1

Intel

945GC

JAUDIO2

(for Ver 5.x)

AUDIO1

(for Ver 6.x)

JAUDIOF1

Super

I/O

PEX16_1

Codec

JCDIN1

PEX1_1

BIOS

JSPDIF_OUT

PCI1

LAN

PCI2

JUSBV3_1

Note: ■ represents the 1 st pin.

Intel

ICH7

JUSB3 JUSB4

JCMOS1

BAT1

SATA3 SATA1

JSFAN1

SATA4 SATA2

JPANEL1

6

945GC-M7 SE / 945GC Micro 775

CHAPTER 2: HARDWARE INSTALLATION

2.1 I

NSTALLING

C

ENTRAL

P

ROCESSING

U

NIT

(CPU)

Special Notice:

Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the

empty socket to ensure pin legs won’t be damaged.

Pin-Cap

Step 1: Pull the socket locking lever out from the socket and then raise the lever up to a 90-degree angle.

7


Step 2: Look for the triangular cut edge on socket, and the golden dot on

CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation.

Step 2-2:

Step 3: Hold the CPU down firmly, and then lower the lever to locked position to complete the installation.

Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the JCFAN1. This completes the installation.

8

945GC-M7 SE / 945GC Micro 775

2.2 FAN H

EADERS

These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to pin#1.

JCFAN1: CPU Fan Header

JCFAN1

1

4

Pin Assignment

1 Ground

2 +12V

3 FAN RPM rate sense

Fan

Control

JSFAN1: System Fan Header

JSFAN1

Pin

Assignment

1 Ground

2 +12V

3 FAN RPM rate sense

1

3

Note:

The JCFAN1 and JSFAN1 support 4-pin and 3-pin head connector. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to GND.

9


2.3 I

NSTALLING

S

YSTEM

M

EMORY

A. DDR2 module

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.

10

B. Memory Capacity

DIMM Socket

Location

DDR2 Module Total Memory Size

945GC-M7 SE / 945GC Micro 775

C. Dual Channel Memory installation

To trigger the Dual Channel function of the motherboard, the memory module must meet the following requirements:

Install memory module of the same density in pairs, shown in the following table.

Dual Channel Status DDR2_A1 DDR2_B1

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or x16)

11


2.4 C

ONNECTORS AND

S

LOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cables.

1 2

33 34

IDE1: Hard Disk Connectors

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO

Mode 0~4, Bus Master, and Ultra DMA 33/66/100 functionality.

The IDE connector can connect a master and a slave drive, so you can connect up to two hard disk drives.

1 2

39 40

12

945GC-M7 SE / 945GC Micro 775

PEX16_1: PCI-Express x16 Slot

-

-

PCI-Express 1.0a compliant.

Maximum theoretical realized bandwidth of 4GB/s simultaneously per direction, for an aggregate of 8GB/s totally.

PEX1_1: PCI-Express x1 Slot

- PCI-Express 1.0a compliant.

-

-

-

Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.

PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

2X bandwidth over the traditional PCI architecture.

PEX16_1

PEX1_1

PCI1~PCI2: Peripheral Component Interconnect Slots

The motherboard is equipped with 2 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits.

PCI1

PCI2

13


CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO

S

ETUP

J

UMPERS

The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

3.2 D

ETAIL

S

ETTINGS

JPANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep button, and speaker connections. It allows user to connect the PC case’s front panel switch functions.

9

1

SLP

PWR_LED

ON/OFF

+ + -

16

8

+ -

SPK RST

HLED

14

Pin Assignment Function Function

1 +5V

2 N/A

3 N/A

4 Speaker

5 HDD LED (+)

6 HDD LED (-)

7 Ground

Speaker

Connector

Hard drive

LED

Reset button

10 Ground

11 N/A

12

13

14

Power LED (+)

Power LED (+)

Power LED (-)

16 Ground

Sleep button

N/A

Power LED

Power-on button

945GC-M7 SE / 945GC Micro 775

JATXPWR1: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX power supply.

12

1

24

13

Pin Assignment

1 +3.3V

2 +3.3V

3 Ground

4 +5V

5 Ground

6 +5V

7 Ground

8 PW_OK

9 Standby

Voltage +5V

10 +12V

11 +12V

12 2 x 12 Detect

13 +3.3V

14 -12V

15 Ground

16 PS_ON

17 Ground

18 Ground

19 Ground

20 -5V

21 +5V

22 +5V

23 +5V

24 Ground

JATXPWR2: ATX Power Source Connector

By connecting this connector, it will provide +12V to CPU power circuit.

2

3

1

4

Pin Assignment

1 +12V

2 +12V

3 Ground

4 Ground

15


JUSB3/JUSB4: Headers for USB 2.0 Ports at Front Panel

This motherboard provides 2 USB 2.0 headers, which allows user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader.

Pin Assignment

JUSB3

9

JUSB4

1

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

10 NC

10 2

SATA1~SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4 channels SATA interface, it satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.

SATA4 SATA2

SATA3 SATA1

1

4

Pin Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

7 Ground

7

16

945GC-M7 SE / 945GC Micro 775

JSPDIF_OUT: Digital Audio out Connectors

This connector allows user to connect the PCI bracket SPDIF output header.

Pin Assignment

1 +5V

2 SPDIF_OUT1

3 Ground

1 3

JAUDIOF1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front panel. It will disable the output on back panel audio connectors.

945GC-M7 SE

9 1

Pin Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

10 2

945GC Mic ro 775

8 Key

9 Left line in

1 2

9 10

17


JCDIN1: CD-ROM Audio-in Connector

This connector allows user to connect the audio source from the variaty devices, like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc..

1 4

Pin Assignment

Channel

Input

2 Ground

3 Ground

4 Right

Input

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and the CMOS data, please carefully follow the procedures to avoid damaging the motherboard.

3

1

Pin 1-2 Close:

Normal Operation (Default).

3

3

1

1

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1.

2.

3.

4.

Remove AC power line.

Set the jumper to “Pin 2-3 close”.

Wait for five seconds.

Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

18

945GC-M7 SE / 945GC Micro 775

JKBV1: Power Source Header for PS/2 Keyboard and Mouse

(Only for 945GC Micro 775)

1 3

1 3

Pin 1-2 Close

+5V for PS/2 keyboard and mouse.

1 3

Pin 2-3 close

PS/2 keyboard and mouse are powered by +5V standby voltage.

Note:

In order to support this function “Power-on system via keyboard and mouse”, “JKBV1” jumper cap should be placed on Pin 2-3.

JUSBV1/JUSBV3_1: Power Source Headers for USB Ports

(Only for 945GC Micro 775)

Pin 1-2 Close:

JUSBV1: +5V for USB ports at JRJ45USB1/JUSB2.

JUSBV3_1: +5V for USB ports at front panel (JUSB3/JUSB4).

Pin 2-3 Close:

JUSBV1: USB ports at JRJ45USB1/JUSB2 are powered by +5V standby voltage.

JUSBV3_1: USB ports at front panel (JUSB3/JUSB4) are powered by +5V standby voltage.

JUSBV1

3 1

3 1

Pin 1-2 close

3 1

JUSBV3_1

1 3 Pin 2-3 close

Note:

In order to support this function “Power-On system via USB device,” “JUSBV1/

JUSBV3_1” jumper cap should be placed on Pin 2-3 individually.

19


JPRNT1: Printer Port Connector

This header allows you to connector printer on the PC.

25

2 1

Pin Assignment Pin Assignment

1 -Strobe

2 -ALF

14 Ground

16 Ground

4 -Error

6 -Init

8 -Scltin

18 Ground

19 -ACK

20 Ground

21 Busy

22 Ground

10 Ground

12 Ground

23 PE

24 Ground

25 SCLT

26 Key

20

945GC-M7 SE / 945GC Micro 775

CHAPTER 4: USEFUL HELP

4.1 D

RIVER

I

NSTALLATION

N

OTE

After you installed your operating system, please insert the Fully Setup

Driver CD into your optical drive and install the driver for better system performance.

You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system.

Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver

CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from http://www.adobe.com/products/acrobat/readstep2.html

21


4.2 A

WARD

BIOS B

EEP

C

ODE

Beep Sound Meaning

One long beep followed by two short beeps

High-low siren sound

Video card not found or video card memory bad

CPU overheated

System will shut down automatically

One Short beep when system boot-up No error found during POST

Long beeps every other second No DRAM detected or install

4.3 E

XTRA

I

NFORMATION

After you fail to update BIOS or BIOS is invaded by virus, the

Boot-Block function will help to restore BIOS. If the following message is shown after boot-up the system, it means the BIOS contents are corrupted.

In this Case, please follow the procedure below to restore the BIOS:

1. Make a bootable floppy disk.

2. Download the Flash Utility “AWDFLASH.exe” from the Biostar website: www.biostar.com.tw

3. Confirm motherboard model and download the respectively BIOS from Biostar website.

4. Copy “AWDFLASH.exe” and respectively BIOS into floppy disk.

5. Insert the bootable disk into floppy drive and press Enter.

7. Type in DOS prompt.

(xxxx means BIOS name.)

9. The BIOS has been recovered and will work properly.

22

945GC-M7 SE / 945GC Micro 775

If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU

0protection function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.

(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

23


4.4 T

ROUBLESHOOTING

Probable Solution

1. No power to the system at all

Power light don’t illuminate, fan

1. Make sure power cable is securely plugged in. inside power supply does not turn on.

2. Replace

3. cable.

Contact technical support.

2. Indicator light on keyboard does not turn on.

System inoperative. Keyboard lights are on, power indicator lights are lit, and hard drive is spinning.

System does not boot from hard disk drive, can be booted from optical drive.

Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place.

1. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup.

2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time.

System only boots from optical drive.

Hard disk can be read and applications can be used but booting from hard disk is impossible.

1. Back up data and applications files.

2. Reformat the hard drive.

Re-install applications and data using backup disks.

Screen message says “Invalid

Configuration” or “CMOS Failure.”

Cannot boot system after installing second hard drive.

Review system’s equipment. Make sure correct information is in setup.

1. Set master/slave jumpers correctly.

2. Run SETUP program and select correct drive types. Call the drive manufacturers for compatibility with other drives.

24

945GC-M7 SE / 945GC Micro 775

CHAPTER 5:

WARPSPEEDER™ III

5.1 I

NTRODUCTION

[WarpSpeeder™ III], a new powerful control utility, features three user-friendly functions including Overclock Manager, Overvoltage

Manager, and Hardware Monitor.

With the Overclock Manager, users can easily adjust the frequency they prefer or they can get the best CPU performance with just one click. The

Overvoltage Manager, on the other hand, helps to power up CPU core voltage and Memory voltage. The cool Hardware Monitor smartly indicates the temperatures, voltage and CPU fan speed as well as the chipset information. Also, in the About panel, you can get detail descriptions about

BIOS model and chipsets. In addition, the frequency status of CPU, memory, VGA and PCI along with the CPU speed are synchronically shown on our main panel.

Moreover, to protect users' computer systems if the setting is not appropriate when testing and results in system fail or hang,

[WarpSpeeder™ III] technology assures the system stability by automatically rebooting the computer and then restart to a speed that is either the original system speed or a suitable one.

5.2 S

YSTEM

R

EQUIREMENT

OS Support: Windows 98 SE, Windows Me, Windows 2000, Windows XP,

Windows Vista

DirectX: DirectX 8.1 or above. (The Windows XP operating system includes DirectX 8.1. If you use Windows XP, you do not need to install

DirectX 8.1.)

25


5.3 I

NSTALLATION

1. Execute the setup execution file, and then the following dialog will pop up. Please click “Next” button and follow the default procedure to install.

2. When you see the following dialog in setup procedure, it means setup is completed. Click “Finish” button.

26

Usage:

The following figures are only for reference, the screen printed in this user manual will change according to your motherboard on hand.

945GC-M7 SE / 945GC Micro 775

5.4 W

ARP

S

PEEDER

™ III

1. Desktop Icon:

After the [WarpSpeeder™ III] has been installed, a [WarpSpeeder™ III] icon will appear on the desktop, just like the icon shown below.

Now you can launch the [WarpSpeeder™ III] utility simply by double-clicking the desktop icon.

2. Main Panel

If you double-click the desktop icon, [WarpSpeeder™ III] will be launched. Please refer to the following figure; the utility’s first window you will see is Main Panel.

Main Panel contains features as follows:

a. Display the CPU Speed, CPU external clock, Memory clock, VGA clock, and PCI clock information. b. Contains About, Voltage/Overclock, and Hardware Monitor

Buttons for invoking respective panels. The On/Off button is for closing the program.

27


3. Overclock/Overvoltage Panel

Click the Overclock/Overvoltage button in the Main Panel, the button will be highlighted and the Overclock/Overvoltage Panel will show up as the following figure. As you can see, the Overclock Panel is on the right side, and the Overvoltage Panel is on the left side.

28

945GC-M7 SE / 945GC Micro 775

Overclock Panel contains these features:

a. “Auto-Overclock”:

User can click this button and [WarpSpeeder™ III] will set the best and stable performance and frequency automatically. A warning dialog as below will show up to notify you that the system may become unstable, click on “OK” to proceed.

Then [WarpSpeeder™ III] utility will execute a series of testing until system fail. Then system will do fail-safe reboot by using

Watchdog function. After reboot, launch the [WarpSpeeder™ III] utility again and the utility will load the previously verified best and stable frequency. b. “Verify”:

If you use the “Manual Adjust” bar to adjust the CPU frequency, then you can click this button and [WarpSpeeder™ III] will proceed a testing for current frequency. If the testing is ok, then the current frequency will be saved into system registry. If the testing fails, system will do a fail-safe rebooting. After reboot, the

[WarpSpeeder™ III] utility will restore to the hardware default setting.

Warning:

Manually overclock is potentially dangerous, especially when the overclocking percentage is over 110 %. We strongly recommend you verify every speed you overclock by click the Verify button. Or, you can just click Auto overclock button and let [WarpSpeeder™ III] automatically gets the best result for you. c. “V3 Engine”/“V6 Engine”/“V9 Engine”:

Provide user the ability to do real-time overclock adjustment. d. “Recovery”:

Click this button and the [WarpSpeeder™ III] utility will restore all values to the hardware default setting.

29


Overvoltage Panel contains these features:

Voltage”:

This function allows user to adjust CPU voltage. Click on “+” to increase or “-“ to decrease the CPU voltage.

Voltage”:

This function allows user to adjust Memory voltage. Click on “+” to increase or “-“ to decrease the Memory voltage.

4. Hardware Monitor Panel

Click the Hardware Monitor button in Main Panel, the button will be highlighted and the Hardware Monitor panel will show up as the following figure.

In this panel, you can get the real-time status information of your system. The information will be refreshed every 1 second.

30

945GC-M7 SE / 945GC Micro 775

5. About Panel

Click the “about” button in Main Panel, the button will be highlighted and the About Panel will show up as the following figure.

In this panel, you can get model name and detail information in hints of all the chipset that are related to overclocking. You can also get the the version number of [WarpSpeeder™ III] utility.

Note:

Because the overclock, overvoltage, and hardware monitor features are controlled by several separate chipset, [WarpSpeeder™ III] divide these features to separate panels. If one chipset is not on board, the correlative button in Main panel will be disabled, but will not interfere other panels’ functions. This property can make

[WarpSpeeder™ III] utility more robust.

31


APPENDENCIES: SPEC IN OTHER LANGUAGE

G

ERMAN

CPU

FSB

Chipsatz

945GC-M7 SE

LGA 775


Celeron D Prozessoren mit bis zu 3,8 GHz

945GC Micro 775

LGA 775


Celeron D Prozessoren mit bis zu 3,8 GHz

*It is recommended to use processors with 95W *It is recommended to use processors with 95W power consumption.

Unterstützt Hyper-Threading power consumption.

Unterstützt Hyper-Threading

Execute Disable Bit

Enhanced Intel SpeedStep®


Execute Disable Bit



533 / 800 / 1066 MHz

Intel 945GC

Intel ICH7

533 / 800 / 1066 MHz

Intel 945GC

Intel ICH7

Grafik

Super E/A

Intel GMA 950

Max. 224MB gemeinsam benutzter

Videospeicher

ITE 8712F

Hardware-Überwachung

Lüfterdrehzahl-Controller

"Smart Guardian"-Funktion von ITE

DDR2 DIMM-Steckplätze x 2

Jeder DIMM unterstützt 256/512MB & 1GB

Arbeitsspeich er

DDR2

Max. 2GB Arbeitsspeicher

Dual-Kanal DDR2 Speichermodul

IDE

SATA

LAN

Intel GMA 950

Max. 224MB gemeinsam benutzter

Videospeicher

ITE 8712F

Hardware-Überwachung

Lüfterdrehzahl-Controller

"Smart Guardian"-Funktion von ITE

DDR2 DIMM-Steckplätze x 2

Jeder DIMM unterstützt 256/512MB & 1GB

DDR2

Max. 2GB Arbeitsspeicher

Dual-Kanal DDR2 Speichermodul

Unterstützt DDR2 400 / 533 / 667 registrierte DIMMs. ECC DIMMs werden nicht unterstützt.

Integrierter IDE-Controller

Ultra DMA 33 / 66 / 100 Bus Master-Modus

Unterstützt PIO-Modus 0~4

Unterstützt DDR2 400 / 533 / 667 registrierte DIMMs. ECC DIMMs werden nicht unterstützt.

Integrierter IDE-Controller

Ultra DMA 33 / 66 / 100 Bus Master-Modus

Unterstützt PIO-Modus 0~4

Integrierter Serial ATA-Controller

Datentransferrate bis zu 3Gb/s

Integrierter Serial ATA-Controller

Datentransferrate bis zu 3Gb/s

Konform mit der SATA-Spezifikation Version 2.0 Konform mit der SATA-Spezifikation Version 2.0

Realtek RTL 8100C / RTL 8110SC(optional)

10 / 100 / 1000 Mb/s Auto-Negotiation


10 / 100 / 1000 Mb/s Auto-Negotiation

32

Steckplätze

945GC-M7 SE

(Gigabit-Bandbreite nur beim RTL 8110SC)

Halb-/ Vollduplex-Funktion

945GC-M7 SE / 945GC Micro 775

945GC Micro 775

(Gigabit-Bandbreite nur beim RTL 8110SC)

Halb-/ Vollduplex-Funktion

Audio-Codec

ALC662(VER 6.X)

5.1-Kanal-Audioausgabe (VER 6.X)

Unterstützt High-Definition Audio

PCI Express x16 Steckplatz

PCI Express x 1-Steckplatz x1 x1

ALC861VD(VER 6.X) / ALC888(VER 5.X)



Unterstützt High-Definition Audio


PCI Express x 1-Steckplatz x1 x1

Druckeranschluss Anschluss x1 Druckeranschluss Anschluss x1

Onboard-Ans chluss S/PDIF-Ausgangsanschluss x1 S/PDIF-Ausgangsanschluss x1

"CMOS löschen"-Sockel x1 "CMOS löschen"-Sockel x1

Rückseiten-E

/A

Stromanschluss (24-polig)

Stromanschluss (4-polig) x1 x1

Stromanschluss (24-polig)

Stromanschluss (4-polig) x1 x1

PS/2-Tastatur x1

PS/2-Tastatur x1

PS/2-Maus x1

PS/2-Maus x1

Serieller Anschluss x1

Serieller Anschluss x1

VGA-Anschluss x1

VGA-Anschluss x1

LAN-Anschluss x1

LAN-Anschluss x1

USB-Anschluss x4

USB-Anschluss x4

Audioanschluss (Ver 6.x) x3



Platinengröße

219 mm (B) X 235 mm (L)

.


OS-Unterstüt zung

Biostar behält sich das Recht vor, ohne

Ankündigung die Unterstützung für ein

Betriebssystem hinzuzufügen oder zu entfernen.

219 mm (B) X 235 mm (L)


Biostar behält sich das Recht vor, ohne

Ankündigung die Unterstützung für ein

Betriebssystem hinzuzufügen oder zu entfernen.

33


UC

F

RANCE

945GC-M7 SE

LGA 775

Processeurs Intel Core2Duo / Pentium 4 /

Pentium D / Celeron D jusqu'à 3,8 GHz

LGA 775

945GC Micro 775

Processeurs Intel Core2Duo / Pentium 4 /

Pentium D / Celeron D jusqu'à 3,8 GHz

*It is recommended to use processors with 95W *It is recommended to use processors with 95W power consumption. power consumption.

Prend en charge les technologies

Hyper-Threading d'exécution de bit de désactivation

Intel SpeedStep® optimisée

Prend en charge les technologies

Hyper-Threading d'exécution de bit de désactivation

Intel SpeedStep® optimisée de mémoire étendue 64

Bus frontal 533 / 800 / 1066 MHz

Chipset

Intel 945GC

Intel ICH7

Graphiques

Intel GMA 950

Mémoire vidéo partagée maximale de 224 Mo de mémoire étendue 64

533 / 800 / 1066 MHz

Intel 945GC

Intel ICH7

Intel GMA 950

Mémoire vidéo partagée maximale de 224 Mo

Super E/S

Mémoire principale

IDE

SATA

ITE 8712F

Moniteur de matériel

Contrôleur de vitesse de ventilateur

Fonction "Gardien intelligent" de l'ITE

Fentes DDR2 DIMM x 2

ITE 8712F

Moniteur de matériel

Contrôleur de vitesse de ventilateur

Fonction "Gardien intelligent" de l'ITE

Fentes DDR2 DIMM x 2

Chaque DIMM prend en charge des DDR2 de

256/512 Mo et 1Go

Chaque DIMM prend en charge des DDR2 de

256/512 Mo et 1Go

Capacité mémoire maximale de 2 Go Capacité mémoire maximale de 2 Go

Module de mémoire DDR2 à mode à double voie Module de mémoire DDR2 à mode à double voie

Prend en charge la DDR2 400 / 533 / 667

Les DIMM à registres et DIMM avec code correcteurs d'erreurs ne sont pas prises en charge

Prend en charge la DDR2 400 / 533 / 667

Les DIMM à registres et DIMM avec code correcteurs d'erreurs ne sont pas prises en charge

Contrôleur IDE intégré Contrôleur IDE intégré

Mode principale de Bus Ultra DMA 33 / 66 / 100 Mode principale de Bus Ultra DMA 33 / 66 / 100

Prend en charge le mode PIO 0~4,

Contrôleur Serial ATA intégré :

Taux de transfert jusqu'à 3 Go/s.

Conforme à la spécification SATA Version 2.0

Prend en charge le mode PIO 0~4,

Contrôleur Serial ATA intégré :

Taux de transfert jusqu'à 3 Go/s.

Conforme à la spécification SATA Version 2.0

34

LAN

ALC662(VER 6.X)

Codec audio Sortie audio à 5.1 voies (VER 6.X)

Prise en charge de l'audio haute définition

945GC-M7 SE / 945GC Micro 775

945GC-M7 SE


10 / 100 / 1000 Mb/s négociation automatique

(La bande passante Gigabit est pour le RTL

8110SC uniquement)


945GC Micro 775


10 / 100 / 1000 Mb/s négociation automatique

(La bande passante Gigabit est pour le RTL

8110SC uniquement)



Sortie audio à 5.1 voies (VER 6.X)

Sortie audio à 7.1 voies (VER 5.X)

Prise en charge de l'audio haute définition

Fentes



Fente PCI

Connecteur de disquette

Connecteur IDE

Connecteur de Port d'imprimante

Connecteur SATA

Connecteur du panneau avant

Connecteur Audio du panneau avant

Connecteur Connecteur d'entrée CD embarqué Connecteur de sortie S/PDIF x1 x1 x2 x1 x1 x1



Fente PCI x1 Connecteur de disquette x1 Connecteur IDE x1 Connecteur de Port d'imprimante x4 Connecteur SATA x1 Connecteur du panneau avant

Connecteur Audio du panneau avant

Connecteur d'entrée CD

Connecteur de sortie S/PDIF

Embase de ventilateur UC

Embase de ventilateur système

Embase d'effacement CMOS

Connecteur USB x1 x1 x1 x2

Embase de ventilateur UC

Embase de ventilateur système

Embase d'effacement CMOS

Connecteur USB

Connecteur d'alimentation (24 broches) x1 Connecteur d'alimentation (24 broches) x1

Connecteur d'alimentation (4 broches) x1 Connecteur d'alimentation (4 broches) x1 x1 x1 x1 x2 x1 x1 x2 x1 x1 x1 x4 x1 x1 x1 x1

E/S du panneau arrière

Clavier PS/2

Souris PS/2

Port série

Port VGA

Port LAN

Port USB

Fiche audio (Ver 6.x) x1 x1 x1 x1 x1 x4 x3

Clavier PS/2

Souris PS/2

Port série

Port VGA

Port LAN

Port USB

Fiche audio (Ver 6.x)

Fiche audio (Ver 5.x)

Dimensions

219mm (l) X 235 mm (H) de la carte


219mm (l) X 235 mm (H)


Support SE Biostar se réserve le droit d'ajouter ou de Biostar se réserve le droit d'ajouter ou de supprimer le support de SE avec ou sans préavis. supprimer le support de SE avec ou sans préavis. x1 x4 x3 x6 x1 x1 x1 x1

35


I

TALIAN

CPU

FSB

945GC-M7 SE 945GC Micro 775

LGA 775

Processore Intel Core2Duo / Pentium 4 /

LGA 775

Processore Intel Core2Duo / Pentium 4 /

Pentium D / Celeron D fino a 3.8 GHz Pentium D / Celeron D fino a 3.8 GHz

*It is recommended to use processors with 95W *It is recommended to use processors with 95W power consumption.

Supporto di Hyper-Threading

Execute Disable Bit


Tecnologia Extended Memory 64

533 / 800 / 1066 MHz power consumption.

Supporto di Hyper-Threading

Execute Disable Bit


Tecnologia Extended Memory 64

533 / 800 / 1066 MHz

Chipset

Intel 945GC

I ntel ICH7

Intel 945GC

I ntel ICH7

Grafica

Intel GMA 950 Intel GMA 950

La memoria video condivisa massima è di 224MB La memoria video condivisa massima è di 224MB

Super I/O

ITE 8712F

Monitoraggio hardware

Controller velocità ventolina

Funzione "Smart Guardian" di ITE

ITE 8712F

Monitoraggio hardware

Controller velocità ventolina

Funzione "Smart Guardian" di ITE

Memoria principale

Alloggi DIMM DDR2 x 2 Alloggi DIMM DDR2 x 2

Ciascun DIMM supporta DDR2 256/512MB e Ciascun DIMM supporta DDR2 256/512MB e

1GB 1GB

Capacità massima della memoria 2GB

Modulo di memoria DDR2 a canale doppio

Supporto di DDR2 400 / 533 / 667

DIMM registrati e DIMM ECC non sono supportati

Capacità massima della memoria 2GB

Modulo di memoria DDR2 a canale doppio

Supporto di DDR2 400 / 533 / 667

DIMM registrati e DIMM ECC non sono supportati

IDE

SATA

LAN

Controller IDE integrato

Modalità Bus Master Ultra DMA 33 / 66 /

100

Supporto modalità PIO Mode 0-4

Controller Serial ATA integrato

Velocità di trasferimento dei dati fino a 3

Gb/s.

Compatibile specifiche SATA Versione 2.0.


Negoziazione automatica 10 / 100 / 1000

Mb/s (la larghezza di banda Gigabit è solo per RTL 8110SC)

Capacità Half / Full Duplex

Controller IDE integrato

Modalità Bus Master Ultra DMA 33 / 66 /

100

Supporto modalità PIO Mode 0-4

Controller Serial ATA integrato

Velocità di trasferimento dei dati fino a 3

Gb/s.

Compatibile specifiche SATA Versione 2.0.


Negoziazione automatica 10 / 100 / 1000

Mb/s (la larghezza di banda Gigabit è solo per RTL 8110SC)

Capacità Half / Full Duplex

36

Codec audio

945GC-M7 SE

ALC662(VER 6.X)

Uscita audio 5.1 canali (VER 6.X)

Supporto audio High-Definition (HD)

945GC-M7 SE / 945GC Micro 775

945GC Micro 775




Supporto audio High-Definition (HD)

Alloggi

Fente PCI Express x16


Alloggio PCI

Connettore floppy

Connettore IDE

Connettore Porta stampante

Connettore SATA

Connettore pannello frontale

Connettore audio frontale

Connettori Connettore CD-in su scheda Connettore output SPDIF x1 x1 x2 x1 x1 x1



Alloggio PCI x1 Connettore floppy x1 Connettore IDE x1 Connettore Porta stampante x4 Connettore SATA x1 Connettore pannello frontale

Connettore audio frontale

Connettore CD-in

Connettore output SPDIF

Collettore ventolina CPU

Collettore ventolina sistema

Collettore cancellazione CMOS

Connettore USB x1 x1 x1 x2

Collettore ventolina CPU

Collettore ventolina sistema

Collettore cancellazione CMOS

Connettore USB

Connettore alimentazione (24 pin) x1 Connettore alimentazione (24 pin) x1

Connettore alimentazione (4 pin) x1 Connettore alimentazione (4 pin) x1 x1 x1 x1 x2 x1 x1 x2 x1 x1 x1 x4 x1 x1 x1 x1

I/O pannello

Tastiera PS/2

Mouse PS/2

Porta seriale

Porta VGA posteriore Porta LAN

Porta USB

Connettore audio (Ver 6.x) x1 x1 x1 x1 x1 x4 x3

Tastiera PS/2

Mouse PS/2

Porta seriale

Porta VGA

Porta LAN

Porta USB

Connettore audio (Ver 6.x)

Connettore audio (Ver 5.x)

Dimension

219 mm (larghezza) x 235 mm (altezza) 219 mm (larghezza) x 235 mm (altezza) i scheda


Sistemi operativi

Biostar si riserva il diritto di aggiungere o supportati rimuovere il supporto di qualsiasi sistema operativo senza preavviso.


Biostar si riserva il diritto di aggiungere o rimuovere il supporto di qualsiasi sistema operativo senza preavviso. x1 x4 x3 x6 x1 x1 x1 x1

37


S

PANISH

945GC-M7 SE

LGA 775

Procesador Intel Core2Duo / Pentium 4 /

Pentium D / Celeron D hasta 3,8 GHz

945GC Micro 775

LGA 775

Procesador Intel Core2Duo / Pentium 4 /

Pentium D / Celeron D hasta 3,8 GHz


CPU

FSB

Gráficos

Súper E/S power consumption.

Admite Hyper-Threading

Bit de deshabilitación de ejecución

Conjunto de Intel 945GC chips

Intel SpeedStep® Mejorado

Tecnología Extended Memory 64

533 / 800 / 1066 MHz

Intel ICH7 power consumption.

Admite Hyper-Threading

Bit de deshabilitación de ejecución

Intel SpeedStep® Mejorado

Tecnología Extended Memory 64

533 / 800 / 1066 MHz

Intel 945GC

Intel ICH7

Intel GMA 950

Memoria máxima de vídeo compartida de

224MB

Intel GMA 950

Memoria máxima de vídeo compartida de

224MB

ITE 8712F

Monitor hardware

Controlador de velocidad de ventilador

Función "Guardia inteligente" de ITE

ITE 8712F

Monitor hardware

Controlador de velocidad de ventilador

Función "Guardia inteligente" de ITE

Ranuras DIMM DDR2 x 2

Cada DIMM admite DDR2 de 256/512MB y 1GB Cada DIMM admite DDR2 de 256/512MB y 1GB

Capacidad máxima de memoria de 2GB

Ranuras DIMM DDR2 x 2

Capacidad máxima de memoria de 2GB

Memoria principal

Módulo de memoria DDR2 de canal Doble

Admite DDR2 de 400 / 533 / 667

No admite DIMM registrados o DIMM compatibles con ECC

Módulo de memoria DDR2 de canal Doble

Admite DDR2 de 400 / 533 / 667

No admite DIMM registrados o DIMM compatibles con ECC

IDE

SATA

Red Local

Controlador IDE integrado

Modo bus maestro Ultra DMA 33 / 66 / 100

Soporte los Modos PIO 0~4.

Controlador ATA Serie Integrado

Tasas de transferencia de hasta 3 Gb/s.

Compatible con la versión SATA 2.0.


Modo bus maestro Ultra DMA 33 / 66 / 100

Soporte los Modos PIO 0~4.

Controlador ATA Serie Integrado

Tasas de transferencia de hasta 3 Gb/s.

Compatible con la versión SATA 2.0.

Realtek RTL 8100C / RTL 8110SC (opcional)

Negociación de 10 / 100 / 1000 Mb/s (el ancho de banda Gigabit es únicamente para 8110SC)

Funciones Half / Full dúplex

Realtek RTL 8100C / RTL 8110SC (opcional)

Negociación de 10 / 100 / 1000 Mb/s (el ancho de banda Gigabit es únicamente para 8110SC)

Funciones Half / Full dúplex

38

Códecs de sonido

Ranuras

Ranura PCI Express x16


Ranura PCI

Conector disco flexible

Conector IDE

Conector Puerto de impresora

Conector SATA

Conector de panel frontal

Conector de sonido frontal

Conector de entrada de CD

Conectores en placa

Conector de salida S/PDIF

Cabecera de ventilador de CPU

X1

X1

Cabecera de ventilador de sistema X1

Cabecera de borrado de CMOS X1

Conector USB X2

X1

X4

X1

X1

X1

Conector de alimentación

(24 patillas)


(4 patillas)

X1

X1

X1

X1

X2

X1

X1

Panel trasero de

E/S

945GC-M7 SE

ALC662(VER 6.X)

Salida de sonido de 5.1 canales (VER 6.X)

Soporte de sonido Alta Definición

Teclado PS/2

Ratón PS/2

Puerto serie

Puerto VGA

Puerto de red local

Puerto USB

Conector de sonido (Ver 6.x)

X1

X1

X1

X1

X1

X4

X3

945GC-M7 SE / 945GC Micro 775

945GC Micro 775




Soporte de sonido Alta Definición



Ranura PCI

Conector disco flexible

Conector IDE

Conector Puerto de impresora

Conector SATA

Conector de panel frontal

Conector de sonido frontal

Conector de entrada de CD

Conector de salida S/PDIF

Cabecera de ventilador de CPU

X1

X1

Cabecera de ventilador de sistema X1

Cabecera de borrado de CMOS X1

Conector USB X2

X1

X4

X1

X1

X1

X1 Conector de alimentación

(24 patillas)


(4 patillas)

X1

Teclado PS/2

Ratón PS/2

Puerto serie

X1

X1

X2

X1

X1

X1

X1

X1

Puerto VGA

Puerto de red local

Puerto USB



X1

X1

X4

X3

X6

Tamaño de la placa

219 mm. (A) X 235 mm. (H) 219 mm. (A) X 235 mm. (H)

Soporte de sistema operativo


Biostar se reserva el derecho de añadir o retirar


Biostar se reserva el derecho de añadir o retirar el soporte de cualquier SO con o sin aviso previo. el soporte de cualquier SO con o sin aviso previo.

39


P

ORTUGUESE

945GC-M7 SE 945GC Micro 775

LGA 775

Processador Intel Core2Duo / Pentium 4 /

LGA 775

Processador Intel Core2Duo / Pentium 4 /

Pentium D / Celeron D até 3,8 GHz Pentium D / Celeron D até 3,8 GHz



Suporta as tecnologias Hyper-Threading

Execute Disable Bit


Extended Memory 64 power consumption.

Suporta as tecnologias Hyper-Threading

Execute Disable Bit


Extended Memory 64

FSB

Chipset

533 / 800 / 1066 MHz

Intel 945GC

Intel ICH7

Placa gráfica

Intel GMA 950

Memória de vídeo máxima partilhada: 224 MB

ITE 8712F

Especificaçã Monitorização do hardware o Super I/O Controlador da velocidade da ventoinha

Função "Smart Guardian" da ITE

Ranhuras DIMM DDR2 x2

Memória principal

IDE

SATA

LAN

533 / 800 / 1066 MHz

Intel 945GC

Intel ICH7

Intel GMA 950

Memória de vídeo máxima partilhada: 224 MB

ITE 8712F

Monitorização do hardware

Controlador da velocidade da ventoinha

Função "Smart Guardian" da ITE

Ranhuras DIMM DDR2 x2

Cada módulo DIMM suporta uma memória

DDR2 de 256/512 MB & 1 GB

Capacidade máxima de memória: 2 GB

Módulo de memória DDR2 de canal duplo

Suporta módulos DDR2 400 / 533 / 667

Os módulos DIMM registados e os DIMM ECC não são suportados

Cada módulo DIMM suporta uma memória

DDR2 de 256/512 MB & 1 GB

Capacidade máxima de memória: 2 GB

Módulo de memória DDR2 de canal duplo

Suporta módulos DDR2 400 / 533 / 667

Os módulos DIMM registados e os DIMM ECC não são suportados


Modo Bus master Ultra DMA 33 / 66 / 100

Suporta o modo PIO 0~4.


Modo Bus master Ultra DMA 33 / 66 / 100

Suporta o modo PIO 0~4.

Controlador Serial ATA integrado Controlador Serial ATA integrado

Velocidades de transmissão de dados até 3 Gb/s. Velocidades de transmissão de dados até 3 Gb/s.

Compatibilidade com a especificação SATA Compatibilidade com a especificação SATA versão 2.0.

Realtek RTL 8100C / RTL 8110SC(opcional)

Auto negociação de 10 / 100 / 1000 Mb/s (a largura de banda Gigabit refere-se apenas à especificação RTL 8110SC)

Capacidade semi/full-duplex versão 2.0.

Realtek RTL 8100C / RTL 8110SC(opcional)

Auto negociação de 10 / 100 / 1000 Mb/s (a largura de banda Gigabit refere-se apenas à especificação RTL 8110SC)

Capacidade semi/full-duplex

40

945GC-M7 SE / 945GC Micro 775

Codec de som

Ranhuras na placa

945GC-M7 SE

ALC662(VER 6.X)

Saída de áudio de 5.1 canais (VER 6.X)

Suporta a especificação High-Definition Audio

Ranhura PCI Express x16

Ranhura PCI Express x1

Ranhura PCI

Conector da unidade de disquetes

Conector IDE

Conector da para impressora

Conector SATA

Conector do painel frontal

Conector de áudio frontal

Conectores Conector para entrada de CDs

Conector de saída S/PDIF

Conector da ventoinha da CPU

Conector da ventoinha do sistema

Conector para limpeza do CMOS

Conector USB

Conector de alimentação (24 pinos)

Conector de alimentação (4 pinos)

945GC Micro 775




Suporta a especificação High-Definition Audio x1 Ranhura PCI Express x16 x1 Ranhura PCI Express x1 x2 Ranhura PCI x1 Conector da unidade de disquetes x1 Conector IDE x1 Conector da para impressora x4 Conector SATA x1 Conector do painel frontal x1 Conector de áudio frontal x1 Conector para entrada de CDs x1 Conector de saída S/PDIF x1 Conector da ventoinha da CPU x1 Conector da ventoinha do sistema x1 Conector para limpeza do CMOS x2 Conector USB x1 Conector de alimentação (24 pinos) x1 Conector de alimentação (4 pinos) x1 x1 x1 x1 x2 x1 x4 x1 x1 x1 x1 x1 x1 x1 x2 x1 x1

Entradas/S aídas no painel traseiro

Teclado PS/2

Rato PS/2

Porta série

Porta VGA

Porta LAN

Porta USB

Tomada de audio (Ver 6.x) x1 x1 x1 x1 x1 x4 x3

Teclado PS/2

Rato PS/2

Porta série

Porta VGA

Porta LAN

Porta USB

Tomada de audio (Ver 6.x)

Tomada de audio (Ver 5.x) x1 x1 x1 x1 x1 x4 x3 x6

Tamanho da placa

219 mm (L) X 235 mm (A)

Sistemas

Windows 2000 / XP / VISTA operativos

A Biostar reserva-se o direito de adicionar ou suportados remover suporte para qualquer sistema operativo com ou sem aviso prévio.

219 mm (L) X 235 mm (A)


A Biostar reserva-se o direito de adicionar ou remover suporte para qualquer sistema operativo com ou sem aviso prévio.

41


P

OLISH

945GC-M7 SE 945GC Micro 775

LGA 775 LGA 775

Procesor Intel Core2Duo / Pentium 4 / Pentium D Procesor Intel Core2Duo / Pentium 4 / Pentium D

/ Celeron D do 3,8 GHz / Celeron D do 3,8 GHz


Procesor

FSB

Chipset

Grafika

Pamięć główna

Super I/O

IDE

SATA

LAN power consumption.

Obsługa Hyper-Threading

Execute Disable Bit



533 / 800 / 1066 MHz

Intel 945GC

Intel ICH7

Intel GMA 950

Maks. wielkość współdzielonej pamięci video wynosi 224MB

Gniazda DDR2 DIMM x 2

Każde gniazdo DIMM obsługuje moduły

256/512MB oraz 1GB DDR2

Maks. wielkość pamięci 2GB

Moduł pamięci DDR2 z trybem podwójnego kanału

Obsługa DDR2 400 / 533 / 667

Brak obsługi Registered DIMM oraz ECC DIMM

ITE 8712F

Monitor H/W

Kontroler prędkości wentylatora

Funkcja ITE "Smart Guardian"

Zintegrowany kontroler IDE

Ultra DMA 33 / 66 / 100 Tryb Bus Master obsługa PIO tryb 0~4

Zintegrowany kontroler Serial ATA

Transfer danych do 3 Gb/s.

Zgodność ze specyfikacją SATA w wersji 2.0. power consumption.

Obsługa Hyper-Threading

Execute Disable Bit



533 / 800 / 1066 MHz

Intel 945GC

Intel ICH7

Intel GMA 950

Maks. wielkość współdzielonej pamięci video wynosi 224MB

Gniazda DDR2 DIMM x 2

Każde gniazdo DIMM obsługuje moduły

256/512MB oraz 1GB DDR2

Maks. wielkość pamięci 2GB

Moduł pamięci DDR2 z trybem podwójnego kanału

Obsługa DDR2 400 / 533 / 667

Brak obsługi Registered DIMM oraz ECC DIMM

ITE 8712F

Monitor H/W

Kontroler prędkości wentylatora

Funkcja ITE "Smart Guardian"

Zintegrowany kontroler IDE

Ultra DMA 33 / 66 / 100 Tryb Bus Master obsługa PIO tryb 0~4

Zintegrowany kontroler Serial ATA

Transfer danych do 3 Gb/s.

Zgodność ze specyfikacją SATA w wersji 2.0.

Realtek RTL 8100C / RTL 8110SC (opcja) Realtek RTL 8100C / RTL 8110SC (opcja)

10 / 100 / 1000 Mb/s z automatyczną negocjacją 10 / 100 / 1000 Mb/s z automatyczną negocjacją szybkości (Pasmo gigabitowe wyłącznie dla RTL

8110SC) szybkości (Pasmo gigabitowe wyłącznie dla RTL

8110SC)

42

945GC-M7 SE

Działanie w trybie połowicznego / pełnego dupleksu

945GC-M7 SE / 945GC Micro 775

945GC Micro 775

Kodek dźwiękowy

ALC662(VER 6.X)

5.1 kanałowe wyjście audio (VER 6.X)

Obsługa High-Definition Audio

Działanie w trybie połowicznego / pełnego dupleksu




Obsługa High-Definition Audio

Gniazda

Gniazdo PCI Express x16


Gniazdo PCI

Złącze napędu dyskietek

Złącze IDE

Złącze Port drukarki

Złącze SATA x1 x1 x2



Gniazdo PCI x1 Złącze napędu dyskietek x1 Złącze IDE x1 Złącze Port drukarki x4 Złącze SATA

Złącze panela przedniego

Przednie złącze audio x1 Złącze panela przedniego x1 Przednie złącze audio x1 x1

Złącza

Złącze wejścia CD x1 Złącze wejścia CD x1 wbudowane

Złącze wyjścia S/PDIF x1 Złącze wyjścia S/PDIF x1

Złącze główkowe wentylatora procesora x1 Złącze główkowe wentylatora procesora x1

Złącze główkowe wentylatora Złącze główkowe wentylatora x1 x1 x2 x1 x1 x1 x4

Back Panel

I/O

Złącze główkowe kasowania CMOS

Złącze USB

Złącze zasilania (24 pinowe)

Złącze zasilania (4 pinowe)

Klawiatura PS/2

Mysz PS/2

Port szeregowy

Port VGA

Port LAN

Port USB

Gniazdo audio (Ver 6.x)

Wymiary płyty

Obsluga systemu operacyjne go

219 mm (S) X 235 mm (W)


Biostar zastrzega sobie prawo dodawania lub odwoływania obsługi dowolnego systemu operacyjnego bez powiadomienia. x1 Złącze główkowe kasowania CMOS x2 Złącze USB x1 Złącze zasilania (24 pinowe) x1 Złącze zasilania (4 pinowe)

Klawiatura PS/2 x1 x1

Mysz PS/2

Port szeregowy x1 x1

Port VGA

Port LAN x1 x4

Port USB

Gniazdo audio (Ver 6.x) x3

Gniazdo audio (Ver 5.x)

219 mm (S) X 235 mm (W)


Biostar zastrzega sobie prawo dodawania lub odwoływania obsługi dowolnego systemu operacyjnego bez powiadomienia. x1 x1 x1 x1 x4 x3 x6 x1 x2 x1 x1 x1

43


R

USSIAN

945GC-M7 SE 945GC

LGA 775

Процессор Intel Core2Duo / Pentium 4 /

LGA 775

Процессор Intel Core2Duo / Pentium 4 /

Pentium D / Celeron D до 3.8 ГГц Pentium D / Celeron D до 3.8 ГГц

CPU

(центральн

*It is recommended to use processors with 95W ый power consumption. процессор)

Поддержка технологий Hyper-Threading

Execute Disable Bit

*It is recommended to use processors with 95W power consumption.

Поддержка технологий Hyper-Threading

Execute Disable Bit





FSB 533 / 800 / 1066 МГц 533 / 800 / 1066 МГц

Набор микросхем

Графика

Intel 945GC

Intel ICH7

Intel 945GC

Intel ICH7

Intel GMA 950 Intel GMA 950

Максимальная совместно используемая видео Максимальная совместно используемая видео

Основная память память составляет 224 МБ

Слоты DDR2 DIMM x 2

Каждый модуль DIMM поддерживает

256/512МБ & 1ГБ DDR2

Максимальная ёмкость памяти 2 ГБ

Модуль памяти с двухканальным режимом

DDR2

Поддержка DDR2 400 / 533 / 667

Не поддерживает зарегистрированные модули DIMM and ECC DIMM память составляет 224 МБ

Слоты DDR2 DIMM x 2

Каждый модуль DIMM поддерживает

256/512МБ & 1ГБ DDR2

Максимальная ёмкость памяти 2 ГБ

Модуль памяти с двухканальным режимом

DDR2

Поддержка DDR2 400 / 533 / 667

Не поддерживает зарегистрированные модули DIMM and ECC DIMM

Super I/O

ITE 8712F

Аппаратный монитор

Регулятор скорости

Функция ITE "Smart Guardian"

(Интеллектуальная защита)

ITE 8712F

Аппаратный монитор

Регулятор скорости

Функция ITE "Smart Guardian"

(Интеллектуальная защита)

IDE

SATA

Локальная сеть

Встроенное устройство управления встроенными интерфейсами устройств

Встроенное устройство управления встроенными интерфейсами устройств

Режим "хозяина" шины Ultra DMA 33 / 66 / 100 Режим "хозяина" шины Ultra DMA 33 / 66 / 100

Поддержка режима PIO 0~4,

Встроенное последовательное устройство управления ATA скорость передачи данных до 3 гигабит/с.

Поддержка режима PIO 0~4,

Встроенное последовательное устройство управления ATA скорость передачи данных до 3 гигабит/с.

Соответствие спецификации SATA версия 2.0. Соответствие спецификации SATA версия 2.0.

Realtek RTL 8100C /

RTL 8110SC (дополнительно)

Realtek RTL 8100C /

RTL 8110SC (дополнительно)

Автоматическое согласование 10 / 100 / 1000 Автоматическое согласование 10 / 100 / 1000

44

Звуковой кодек

Слоты

945GC-M7 SE / 945GC Micro 775

945GC-M7 SE

Мб/с (гигабитная пропускная способность только для гигабитного физического уровня)

Частичная / полная дуплексная способность

ALC662(VER 6.X)

5.1канальный звуковой выход (VER 6.X)

Звуковая поддержка High-Definition

Слот PCI Express x16

Слот PCI Express x1

Слот PCI

945GC

Мб/с (гигабитная пропускная способность только для гигабитного физического уровня)

Частичная / полная дуплексная способность




Звуковая поддержка High-Definition x1 Слот PCI Express x16 x1 Слот PCI Express x1 x2 Слот PCI x1 x1 x2

Разъём IDE x1 Разъём IDE x1

Разъём Порт подключения принтера x1 Разъём Порт подключения принтера x1

Разъём SATA x4 Разъём SATA x4

Встроенны й разъём

Разъём ввода для CD

Разъём вывода для S/PDIF

Контактирующее приспособление вентилятора центрального процессора x1

Контактирующее приспособление x1 Разъём ввода для CD x1 Разъём вывода для S/PDIF

Контактирующее приспособление x1 x1 вентилятора центрального процессора x1

Контактирующее приспособление

Открытое контактирующее приспособление CMOS x1

Открытое контактирующее приспособление CMOS x1

Задняя панель средств ввода-выв ода

Клавиатура PS/2

Мышь PS/2

Порт VGA

Порт LAN

Гнездо для подключения наушников (Ver 6.x) x1 x1 x1 x1

Клавиатура PS/2

Мышь PS/2

Последовательный порт x1

Порт LAN x1 x1 x1 x1

USB-порт x4 x3 наушников (Ver 6.x)

Гнездо для подключения наушников (Ver 5.x) x3 x6

Размер панели

Поддержка


Biostar сохраняет за собой право добавлять

OS или удалять средства обеспечения для OS с или без предварительного уведомления.


Biostar сохраняет за собой право добавлять или удалять средства обеспечения для OS с или без предварительного уведомления.

45


A

RABIC

945GC Micro 775 945GC-M7 SE

LGA 775 LGA 775

تﺎﺠﻟﺎﻌﻡIntel Core2Duo / Pentium 4 / Pentium D / تﺎﺠﻟﺎﻌﻡIntel Core2Duo / Pentium 4 / Pentium D /

Celeron D ﺰﺕﺮه ﺎﺠﻴﺝ 3.8

ﻰﻟإ ﻞﺼ ﻳ ددﺮﺘ ﺑ Celeron D ﺰﺕﺮه ﺎﺠﻴﺝ 3.8

ﻰﻟإ ﻞﺼ ﻳ ددﺮﺘ ﺑ

*It is recommended to use processors with 95W *It is recommended to use processors with 95W power consumption. power consumption.

تﺎﻴﻨﻘﺕ ﻢﻋﺪﺕHyper-Threading

Execute Disable Bit



Execute Disable Bit



ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو

ﺔﻳﺰآﺮﻤﻟا

Intel 945GC

Intel ICH7

Intel GMA 950

ﺔآﺮﺘﺸﻤﻟا ﻮﻳﺪﻴﻔﻟا ةﺮآاﺬﻟ ﺔﻌﺳ ﻰﺼﻗأ224ﺖﻳﺎﺑ ﺎﺠﻴﻡ

Intel 945GC

Intel ICH7

Intel GMA 950

ﺔآﺮﺘﺸﻤﻟا ﻮﻳﺪﻴﻔﻟا ةﺮآاﺬﻟ ﺔﻌﺳ ﻰﺼﻗأ224ﺖﻳﺎﺑ ﺎﺠﻴﻡ

ﺔﺤﺘﻓDDR2 DIMMدﺪﻋ2 ﺔﺤﺘﻓDDR2 DIMMدﺪﻋ2

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺕDIMM عﻮﻥ ﻦﻡ ةﺮآاذ ﻢﻋﺪﺕ DDR2 ﺔﻌﺳ 256/512 ﺎﺠﻴﻡ ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺕDIMM عﻮﻥ ﻦﻡ ةﺮآاذ ﻢﻋﺪﺕ DDR2 ﺔﻌﺳ 256/512 ﺎﺠﻴﻡ

ﺖﻳﺎﺑ ﺎﺠﻴﺝ 1 و ﺖﻳﺎﺑ

ﺖﻳﺎﺑ ﺎﺠﻴﺝ 2 ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ

ﺖﻳﺎﺑ ﺎﺠﻴﺝ 1 و ﺖﻳﺎﺑ

ﺖﻳﺎﺑ ﺎﺠﻴﺝ 2 ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ

ةﺮآاذ ةﺪﺣوDDR2 ةﺎﻨﻘﻟا ﺔﺝودﺰﻡ / ﺔﻳدﺎﺣأ

عﻮﻥ ﻦﻡ ةﺮآاﺬﻟا ﻢﻋﺪﺕDDR2 تﺎﻌﺳ 400 / 533 / 667ﺖﻳﺎﺑ ﺎﺠﻴﻡ

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺕ ﻻDIMM ﻊﻡ ﻖﻓاﻮﺘﺕ ﻻ ﻲﺘﻟا ﻚﻠﺕو ECC

ITE 8712F

ةﺰﻬﺝﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻡ

ﺔﺣوﺮﻤﻟا ﺔﻋﺮﺳ ﻲﻓ ﺐﻗاﺮﻡ

ﺔﻔﻴﻇو"Smart Guardian" ﻦﻡ ITE

ﻢﻜﺤﺘﻡIDEﻞﻡﺎﻜﺘﻡ

ﺔﻴﻨﻘﺘﺑ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100

ﻲﺴﻴﺋر ﻊﺿو

ﻊﺿو ﻢﻋدPIO Mode 0~4

ﻢﻜﺤﺘﻡSerial ATAﻞﻡﺎﻜﺘﻡ

.

ﺔﻴﻥﺎﺛ / ﺖﺑﺎﺠﻴﺝ 3 ﻰﻟإ ﻞﺼﺕ تﺎﻋﺮﺴﺑ تﺎﻥﺎﻴﺒﻟا ﻞﻘﻥ

تﺎﻔﺹاﻮﻤﻟ ﺔﻘﺑﺎﻄﻡSATA ﺹﻹا 2.0.

Realtek RTL 8100C /

RTL 8110SC ( يرﺎﻴﺘﺧا )

ﺔﻴﻥﺎﺛ / ﺖﺑ ﺎﺠﻴﺝ 1 و ﺔﻴﻥﺎﺛ / ﺖﻳﺎﺑ ﺎﺠﻴﻡ 100 / 10 ﻲﺋﺎﻘﻠ ﺕ ضوﺎﻔﺕ

ةﺮآاذ ةﺪﺣوDDR2 ةﺎﻨﻘﻟا ﺔﺝودﺰﻡ / ﺔﻳدﺎﺣأ

عﻮﻥ ﻦﻡ ةﺮآاﺬﻟا ﻢﻋﺪﺕDDR2 تﺎﻌﺳ 400 / 533 / 667ﺖﻳﺎﺑ ﺎﺠﻴﻡ

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺕ ﻻDIMM ﻊﻡ ﻖﻓاﻮﺘﺕ ﻻ ﻲﺘﻟا ﻚﻠﺕو ECC

ITE 8712F

ةﺰﻬﺝﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻡ

ﺔﺣوﺮﻤﻟا ﺔﻋﺮ ﺳ ﻲﻓ ﺐﻗاﺮﻡ

ﺔﻔﻴﻇو"Smart Guardian" ﻦﻡ ITE

ﻢﻜﺤﺘﻡIDEﻞﻡﺎﻜﺘﻡ

ﺔﻴﻨﻘﺘﺑ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100

ﻲﺴﻴﺋر ﻊﺿو

ﻊﺿو ﻢﻋدPIO Mode 0~4

ﻢﻜﺤﺘﻡSerial ATAﻞﻡﺎﻜﺘﻡ

.

ﺔﻴﻥﺎﺛ / ﺖﺑﺎﺠﻴﺝ 3 ﻰﻟإ ﻞﺼﺕ تﺎﻋﺮﺴﺑ تﺎﻥﺎﻴﺒﻟا ﻞﻘﻥ

تﺎﻔﺹاﻮﻤﻟ ﺔﻘﺑﺎﻄﻡSATA راﺪﺹﻹا 2.0.

Realtek RTL 8100C /

RTL 8110SC ( يرﺎﻴﺘﺧا )

ﺔﻴﻥﺎﺛ / ﺖﺑ ﺎﺠﻴﺝ 1 و ﺔﻴﻥﺎﺛ / ﺖﻳﺎﺑ ﺎﺠﻴﻡ 100 / 10 ﻲﺋﺎﻘﻠﺕ ضوﺎﻔﺕ

ﻲﺒﻥﺎﺠﻟا ﻲﻡﺎﻡﻷا ﻞﻗﺎﻨﻟا

ﺢﺋاﺮﺸﻟا ﺔﻋﻮﻤﺠﻡ

تﺎﻡﻮﺳﺮﻟا ﺔﻗﺎﻄﺑ

ﺔﻴﺴﻴﺋﺮﻟا ةﺮآاﺬﻟا

Super I/O

IDE ﺬﻔﻨﻡ

SATA

ﺔﻴﻠﺧاد ﺔﻜﺒﺵ

100 / 10

46

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

4 دﺪﻋ

3 دﺪﻋ

6 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

4 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

2 دﺪﻋ

1 دﺪﻋ

945GC Micro 775

ﻰﻠﻋ ﻂﻘﻓ رﻮﺼﻘﻡ ﺖﺑﺎﺠﻴﺠﻠﻟ يددﺮﺘﻟا قﺎﻄﻨﻟاRTL 8110SC

ﻲﻔﺼﻨﻟا / ﻞﻡﺎﻜﻟا جودﺰﻤﻟا ﻞﻘﻨﻟا ﺔﻴﻥﺎﻜﻡإ


5.1

تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ (VER 6.X)

7.1


ﻦﻡ ﻒﻳﺮﻌﺘﻟا ﻲﻟﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺕ ﻢﻋﺪﺕ

1 دﺪﻋ

1 دﺪﻋ

2 دﺪﻋ

PCI Express x16

PCI Express x1

ﺔﺤﺘﻓ

ﺔﺤﺘﻓ

PCI ﺔﺤﺘﻓ

ﺔﻥﺮﻡ صاﺮﻗأ كﺮﺤﻡ ﺬﻔﻨﻡ

IDE ﺬﻔﻨﻡ

ﺔﻌﺑﺎﻃ ﺬﻔﻨﻡ

SATA ﺬﻔﻨﻡ

ﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟا ﺬﻔﻨﻡ

ﻲﻡﺎﻡﻷا تﻮﺼﻟا ﺬﻔﻨﻡ

CD-IN ﺬﻔﻨﻡ

S/PDIF جﺮﺧ ﺬﻔﻨﻡ

ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻡ ﺔﻠﺹو

مﺎﻈﻨﻟا ﺔﺣوﺮﻡ ﺔﻠﺹو

CMOS ﺢﺴﻡ ﺔﻠﺹو

USB ﺬﻔﻨﻡ

( سﻮﺑد 24 ) ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺕ ﺬﻔﻨﻡ

( ﺲﻴﺑﺎﺑد 4 ) ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺕ ﺬﻔﻨﻡ

PS/2 ﺢﻴﺕﺎﻔﻡ ﺔﺣﻮﻟ

PS/2 سوﺎﻡ

ﻲﻠﺴﻠﺴﺕ ﺬﻔﻨﻡ

VGA ﺬﻔﻨﻡ

ﺔﻴﻠﺤﻡ لﺎﺼﺕا ﺔﻜﺒﺵ ﺬﻔﻨﻡ

USB ﺬﻓﺎﻨﻡ

(Ver 6.x) تﻮﺹ ﺲﺒﻘﻡ

(Ver 5.x) تﻮﺹ ﺲﺒﻘﻡ

( عﺎﻔﺕرا ) ﻢﻡ 235 X ( ضﺮﻋ ) ﻢﻡ 219


.

رﺎﻄﺧإ نوﺪﺑ

ﻰﻠﻋ ﻂﻘﻓ رﻮﺼﻘﻡ ﺖﺑﺎﺠﻴﺠﻠﻟ يددﺮﺘﻟا قﺎﻄﻨﻟاRTL 8110SC

ﻲﻔﺼﻨﻟا / ﻞﻡﺎﻜﻟا جودﺰﻤﻟا ﻞﻘﻨﻟا ﺔﻴﻥﺎﻜﻡإ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

4 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1

1

2

945GC-M7 SE / 945GC Micro 775

دﺪﻋ

دﺪﻋ

دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

2 دﺪﻋ

1 دﺪﻋ

1

1

1

1

1

1

4

3

دﺪﻋ

دﺪﻋ

دﺪﻋ

دﺪﻋ

دﺪﻋ

دﺪﻋ

دﺪﻋ

دﺪﻋ

945GC-M7 SE

ALC662(VER 6.X)

5.1


ﻦﻡ ﻒﻳﺮﻌﺘﻟا ﻲﻟﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺕ ﻢﻋﺪﺕ

ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻡ ﺔﻠﺹو

مﺎﻈﻨﻟا ﺔﺣوﺮﻡ ﺔﻠﺹو

CMOS ﺢﺴﻡ ﺔﻠﺹو

USB ﺬﻔﻨﻡ

( سﻮﺑد 24 ) ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺕ ﺬﻔﻨﻡ

(

PCI Express x16

PCI Express x1

ﺲﻴﺑﺎﺑد 4 ) ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺕ ﺬﻔﻨﻡ

ﺔﻥﺮﻡ صاﺮﻗأ كﺮﺤﻡ ﺬﻔﻨﻡ

IDE ﺬﻔﻨﻡ

ﻲﻡﺎﻡﻷا تﻮﺼﻟا ﺬﻔﻨﻡ

CD-IN ﺬﻔﻨﻡ

S/PDIF جﺮﺧ ﺬﻔﻨﻡ

ﺔﻌﺑﺎﻃ ﺬﻔﻨﻡ

SATA ﺬﻔﻨﻡ

ﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟا ﺬﻔﻨﻡ

PS/2

PCI ﺔﺤﺘﻓ

ﺢﻴﺕﺎﻔﻡ ﺔﺣﻮﻟ

PS/2

ﺔﻴﻠﺤﻡ لﺎﺼﺕا ﺔﻜﺒﺵ ﺬﻔﻨﻡ

(Ver 6.x)

ﻲﻠﺴﻠﺴﺕ ﺬﻔﻨﻡ

VGA

ﺔﺤﺘﻓ

ﺔﺤﺘﻓ

س وﺎﻡ

ﺬﻔﻨﻡ

USB ﺬﻓﺎﻨﻡ

تﻮﺹ ﺲﺒﻘﻡ

( عﺎﻔﺕرا ) ﻢﻡ 235 X ( ضﺮﻋ ) ﻢﻡ 219


ﻆﻔﺘﺤﺕBiostar وأ رﺎﻄﺧﺈﺑ ﻞﻴﻐﺸﺕ مﺎﻈﻥ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿإ ﻲﻓ ﺎﻬﻘﺤﺑ

.

رﺎﻄﺧإ نوﺪﺑ

تﻮﺼﻟا ﻚﻳدﻮآ

تﺎﺤﺘﻔﻟا

ﺢﻄﺳ ﻰﻠﻋ ﺬﻓ ﺎﻨﻤﻟا

ﺔﺣﻮﻠﻟا

جﺮﺧ / ﻞﺧد ﺬﻓﺎﻨﻡ

ﺔﻴﻔﻠﺨﻟا ﺔﺣﻮﻠﻟا

ﺔﺣﻮﻠﻟا ﻢﺠﺣ

ﻞﻴﻐﺸﺘﻟا ﺔﻤﻈﻥأ ﻢﻋد

47


J

APANESE

945GC-M7 SE

LGA 775


Celeron D processor up to 3.8 GHz

945GC Micro 775

LGA 775


Celeron D processor up to 3.8 GHz

グラフィック

ス



Hyper-Threading

Execute Disable Bit


FSB


533 / 800 / 1066 MHz

チップセット

Intel 945GC

Intel ICH7

Intel GMA 950

最大の共有ビデオメモリは

メインメモリ

最大メモリ容量 2GB

デュアルチャンネルモードDDR2メモリモジュール

DDR2 400 / 533 / 667 をサポート

登録済み

DIMMとECC DIMMはサポートされません

ITE 8712F

224MBです

DDR2 DIMMスロット x 2

各

DIMMは256/512MB & 1GB DDR2をサポート power consumption.

Hyper-Threading

Execute Disable Bit



533 / 800 / 1066 MHz

Intel 945GC

Intel ICH7

Intel GMA 950

最大の共有ビデオメモリは 224MBです

DDR2 DIMMスロット x 2

各

DIMMは256/512MB & 1GB DDR2をサポート

最大メモリ容量 2GB

デュアルチャンネルモードDDR2メモリモジュール

DDR2 400 / 533 / 667 をサポート

登録済み

DIMMとECC DIMMはサポートされません

ITE 8712F

Super I/O

IDE

SATA

H/Wモニター

ファン速度コントローラ / モニター

ITEの「スマートガーディアン」機能

統合 IDEコントローラ

Ultra DMA 33 / 66 / 100バスマスタモード

PIO Mode 0~4のサポート

統合シリアル ATAコントローラ

最高 3 Gb/秒のデータ転送速度

SATAバージョン2.0仕様に準拠。

Realtek RTL 8100C / RTL 8110SC(オプション)

10/100 LAN

10 / 100 / 1000 Mb/秒のオートネゴシエーション

(Gigabitバンド幅はRTL 8110SC専用です)

半 /全二重機能

サウンド

Codec

ALC662(VER 6.X)

5.1チャンネルオーディオアウト(VER 6.X)

H/Wモニター

ファン速度コントローラ / モニター

ITEの「スマートガーディアン」機能

統合 IDEコントローラ

Ultra DMA 33 / 66 / 100バスマスタモード

PIO Mode 0~4のサポート

統合シリアル ATAコントローラ

最高 3 Gb/秒のデータ転送速度

SATAバージョン2.0仕様に準拠。

Realtek RTL 8100C / RTL 8110SC(オプション)

10 / 100 / 1000 Mb/秒のオートネゴシエーション

(Gigabitバンド幅はRTL 8110SC専用です)

半 /全二重機能


5.1チャンネルオーディオアウト(VER 6.X)

48

スロット

945GC-M7 SE / 945GC Micro 775

945GC-M7 SE 945GC Micro 775

ハイデフィニションオーディオのサポート 7.1チャンネルオーディオアウト(VER 5.X)

ハイデフィニションオーディオのサポート

PCI Express x16スロット

PCI Express x1スロット x1 x1

PCI Express x16スロット x1

PCI Express x1スロット x1

フロッピーコネクタ x1 x1

プリンタポートコネクタ

x1 x1

オンボードコ

ネクタ

フロントパネルコネクタ x1 x1

フロントオーディオコネクタ x1 フロントオーディオコネクタ x1

システムファンヘッダ x1 x1

電源コネクタ (24ピン)

電源コネクタ (4ピン) x1 x1


OSサポート Biostarは事前のサポートなしにOSサポートを追加ま

たは削除する権利を留保します。

電源コネクタ (24ピン)

電源コネクタ (4ピン) x1 x1

背面パネル

I/O

PS/2キーボード x1

PS/2キーボード x1

PS/2マウス x1

PS/2マウス x1

シリアルポート

シリアルポート

x1

x1

VGAポート x1

VGAポート x1

LANポート x1

LANポート x1

USBポート x4

USBポート x4

オーディオジャック

(Ver 6.x) x3

オーディオジャック (Ver 6.x) x3

オーディオジャック (Ver 5.x) x6

ボードサイズ 219 mm (幅) X 235 mm (高さ) 219 mm (幅) X 235 mm (高さ)


Biostarは事前のサポートなしにOSサポートを追加ま

たは削除する権利を留保します。

2007/05/22

49

945GC-M7 SE / 945GC Micro 775

BIOS SETUP

BIOS Setup........................................................................................1

1 Main Menu.....................................................................................................3

2 Standard CMOS Features ..............................................................................6

3 Advanced BIOS Features...............................................................................8

4 Advanced Chipset Features..........................................................................14

5 Integrated Peripherals ..................................................................................18

6 Power Management Setup ...........................................................................23

7 PnP/PCI Configurations ...............................................................................28

8 PC Health Status ..........................................................................................30

9 Performance Booster Zone...........................................................................32

i

945GC-M7 SE / 945GC Micro 775

BIOS Setup

Introduction

This manual discussed Phoenix-Award™ Setup program built into the ROM BIOS. The

Setup program allows users to modify the basic system configuration. This special information is then stored in battery-backed RAM so that it retains the Setup information when the power is turned off.

The Phoenix-Award BIOS™ installed in your computer system’s ROM (Read Only

Memory) is a custom version of an industry standard BIOS. This means that it supports

Intel Pentium ® 4 processor input/output system. The BIOS provides critical low-level support for standard devices such as disk drives and serial and parallel ports.

Adding important has customized the Phoenix-Award BIOS™, but nonstandard, features such as virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.

The rest of this manual is intended to guide you through the process of configuring your system using Setup.

Plug and Play Support

These PHOENIX-AWARD BIOS supports the Plug and Play Version 1.0A specification.

ESCD (Extended System Configuration Data) write is supported.

EPA Green PC Support

This PHOENIX-AWARD BIOS supports Version 1.03 of the EPA Green PC specification.

APM Support

These PHOENIX-AWARD BIOS supports Version 1.1&1.2 of the Advanced Power

Management (APM) specification. Power management features are implemented via the

System Management Interrupt (SMI). Sleep and Suspend power management modes are supported. Power to the hard disk drives and video monitors can be managed by this

PHOENIX-AWARD BIOS.

ACPI Support

Phoenix-Award ACPI BIOS support Version 1.0b of Advanced Configuration and Power interface specification (ACPI). It provides ASL code for power management and device configuration capabilities as defined in the ACPI specification, developed by Microsoft,

Intel and Toshiba.

1

945GC-M7 SE / 945GC Micro 775

PCI Bus Support

This PHOENIX-AWARD BIOS also supports Version 3.0 of the Intel PCI (Peripheral

Component Interconnect) local bus specification.

DRAM Support

DDR2 SDRAM (Double Data Rate Two Synchronous DRAM) are supported.

Supported CPUs

This PHOENIX-AWARD BIOS supports the Intel CPU.

Using Setup

In general, you use the arrow keys to highlight items, press <Enter> to select, use the

<PgUp> and <PgDn> keys to change entries, press <F1> for help and press <Esc> to quit.

The following table provides more detail about how to navigate in the Setup program by using the keyboard.

Keystroke Function

Up arrow

Down arrow

Left arrow

Right arrow

Move Enter

PgUp key

PgDn key

+ Key

- Key

Esc key

F1 key

F5 key

F7 key

F10 key

Move to previous item

Move to next item

Move to the item on the left (menu bar)

Move to the item on the right (menu bar)

Move to the item you desired

Increase the numeric value or make changes

Decrease the numeric value or make changes

Increase the numeric value or make changes

Decrease the numeric value or make changes

Main Menu – Quit and not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu – Exit

Current page and return to Main Menu

General help on Setup navigation keys

Load previous values from CMOS

Load the optimized defaults

Save all the CMOS changes and exit

2

945GC-M7 SE / 945GC Micro 775

1 Main Menu

Once you enter Phoenix-Award BIOS™ CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions. Use the arrow keys to select among the items and press <Enter> to accept and enter the sub-menu.

!! WARNING !!

The information about BIOS defaults on manual (Figure

1,2,3,4,5,6,7,8,9) is just for reference, please refer to the BIOS installed on board, for update information.

 Figure 1. Main Menu

Standard CMOS Features

This submenu contains industry standard configurable options.

Advanced BIOS Features

This submenu allows you to configure enhanced features of the BIOS.

Advanced Chipset Features

This submenu allows you to configure special chipset features.

3

945GC-M7 SE / 945GC Micro 775

Integrated Peripherals

This submenu allows you to configure certain IDE hard drive options and Programmed

Input/ Output features.

Power Management Setup

This submenu allows you to configure the power management features.

PnP/PCI Configurations

This submenu allows you to configure certain “Plug and Play” and PCI options.

PC Health Status

This submenu allows you to monitor the hardware of your system.

Performance Booster Zone

This submenu allows you to change CPU Vcore Voltage and CPU/PCI clock. (However, this function is strongly recommended not to use. Not properly change the voltage

and clock may cause the CPU or M/B damage!)

Load Optimized Defaults

This selection allows you to reload the BIOS when the system is having problems particularly with the boot sequence. These configurations are factory settings optimized for this system. A confirmation message will be displayed before defaults are set.

Set Supervisor Password

Setting the supervisor password will prohibit everyone except the supervisor from making changes using the CMOS Setup Utility.You will be prompted with to enter a password.

4

945GC-M7 SE / 945GC Micro 775

Set User Password

If the Supervisor Password is not set, then the User Password will function in the same way as the Supervisor Password. If the Supervisor Password is set and the User Password is set, the “User” will only be able to view configurations but will not be able to change them.

Save & Exit Setup

Save all configuration changes to CMOS (memory) and exit setup. Confirmation message will be displayed before proceeding.

Exit Without Saving

Abandon all changes made during the current session and exit setup. confirmation message will be displayed before proceeding.

Upgrade BIOS

This submenu allows you to upgrade bios.

5

945GC-M7 SE / 945GC Micro 775

2 Standard CMOS Features

The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the<PgUp> or <PgDn> keys to select the value you want in each item.

Figure 2. Standard CMOS Setup

Main Menu Selections

This table shows the selections that you can make on the Main Menu.

Date

Time mm : dd : yy hh : mm : ss

IDE Channel 0 Master Options are in its sub menu.

IDE Channel 0 Slave Options are in its sub menu.

Set the system date. Note that the ‘Day’ automatically changes when you set the date.

Set the system internal clock.

Press <Enter> to enter the sub menu of detailed options

Press <Enter> to enter the sub menu of detailed options.

6

945GC-M7 SE / 945GC Micro 775

IDE Channel 1 Master Options are in its sub menu.

IDE Channel 1 Slave Options are in its sub menu.

Drive A

Drive B

Halt On

Base Memory

360K, 5.25 in

1.2M, 5.25 in

720K, 3.5 in

1.44M, 3.5 in

2.88M, 3.5 in

None

All Errors

No Errors

All, but Keyboard

All, but Diskette

All, but Disk/ Key

N/A



Select the type of floppy disk drive installed in your system.

Select the situation in which you want the BIOS to stop the POST process and notify you.

Extended Memory

Total Memory

N/A

N/A

Displays the amount of conventional memory detected during boot up.

Displays the amount of extended memory detected during boot up.

Displays the total memory available in the system.

7

945GC-M7 SE / 945GC Micro 775

3 Advanced BIOS Features

 Figure 3. Advanced BIOS Setup

CPU FEATURE

Delay Prior to Thermal

Set this item to enable the CPU Thermal function to engage after the specified time.

The Choices: 4 Min, 8 Min, 16 Min (default), 32 Min.

8

945GC-M7 SE / 945GC Micro 775

Thermal Management

This option allows you to choose the thermal management method of your monitor.

The Choices: Thermal Monitor 1 (default), Thermal Monitor2.

Notes: The choices will be different according to your CPU features.

TM2 Bus Ratio

This option represents the frequency. (Bus ratio of the throttled performance state that will be initiated when the on-die sensor goes from not hot to hot.)

Min= 0 Max= 255 Key in a DEC number.

The Choices: 0X (default).

TM2 Bus VID

This option represents the voltage of the throttled performance state that will be initiated when the on-die sensor goes from not hot to hot.

The Choices: 0.8375V (default), 0.8375V-1.6000V.

Limit CPUID MaxVal

Set limit CPUID MaxVal to 3, it should be “Disabled” for Win XP.

The Choices: Disabled (default), Enabled.

C1E Function

This item allows you to choose the C1E function.

The Choices: Auto (default), Disabled.

Execute Disable Bit

When disabled, forces the XD feature flag to always return 0.

The Choices: Enabled (default), Disabled.

Virtualization Technology

When enabled, a VMM can utilize the additional hardware capabilities provided by

Vanderpool Technology.

The Choices: Enabled (default), Disabled

9

Cache Setup

945GC-M7 SE / 945GC Micro 775

CPU L3 Cache

Depending on the CPU/chipset in use, you may be able to increase memory access time with this option. cache. cache.

Boot Seq & Floppy Setup

This item allows you to setup Boot Seq & Floppy.

10

945GC-M7 SE / 945GC Micro 775

Hard Disk Boot Priority

These BIOS attempt to arrange the Hard Disk boot sequence automatically.

This will depend on which Hard Disk is installed.

The Choices: Pri. Master, Pri.Slave, Sec.Master, Sec.Slave, USBHDD0, USBHDD1,

USBHDD2 and Bootable Add-in Cards.

First/Second/Third Boot Device

These BIOS attempt to load the operating system from the device in the sequence selected in these items.

The Choices: Floppy, LS120, Hard Disk, CDROM, ZIP100, USB-FDD, USB-ZIP,

USB-CDROM, LAN, Disabled.

Boot Other Device

When enabled, BIOS will try to load the operating system from other device when it failed to load from the three devices above.

The Choices: Enabled (default), Disabled

Swap Floppy Drive

For systems with two floppy drives, this option allows you to swap logical drive assignments.


Boot Up Floppy Seek

Enabling this option will test the floppy drives to determine if they have 40 or 80 tracks. Disabling this option reduces the time it takes to boot-up.

The Choices: Disabled, Enabled (default).

11

945GC-M7 SE / 945GC Micro 775

Report NO FDD for Win95

The Choices: NO (default), YES.

Virus Warning

This option allows you to choose the Virus Warning feature that is used to protect the IDE Hard Disk boot sector. If this function is enabled and an attempt is made to write to the boot sector, BIOS will display a warning message on the screen and sound an alarm beep.

Disabled (default)

Enabled

Virus protection is disabled.

Virus protection is activated.

Hyper-Threading Technology

This option allows you to enable or disable CPU Hyper-Threading. “Enabled” for Windows XP and Linux 2.4.x (OS optimized for Hyper-Threading Technology.)

“Disabled” for other OS (OS not optimized for Hyper-Threading Technology.)


Quick Power On Self Test

Enabling this option will cause an abridged version of the Power On

Self-Test (POST) to execute after you power up the computer.

Disabled Normal POST.

Enabled (default) Enable quick POST.

Boot Up NumLock Status

Selects the NumLock State after power on.

On (default) Numpad is arrow keys.

Off

Gate A20 Option

Numpad is number keys.

Select if chipset or keyboard controller should control Gate A20.

Normal

Fast (default)

A pin in the keyboard controller controls GateA20.

Lets chipset control Gate A20.

Typematic Rate Setting

When a key is held down, the keystroke will repeat at a rate determined by

the keyboard controller. When enabled, the typematic rate and typematic

delay can be configured.


Typematic Rate (Chars/Sec)

Sets the rate at which a keystroke is repeated when you hold the keydown.

The Choices: 6 (default), 8,10,12,15,20,24,30

12

945GC-M7 SE / 945GC Micro 775

Typematic Delay (Msec)

Sets the delay time after the key is held down before it begins to repeat

the keystroke.

The Choices: 250 (default), 500, 750, and 1000.

Security Option

This option will enable only individuals with passwords to bring the system

online and/or to use the CMOS Setup Utility.

System

Setup (default)

A password is required for the system to boot and is also required to access the Setup Utility.

A password is required to access the Setup Utility only.

This will only apply if passwords are set from the Setup main menu.

APIC Mode

Selecting Enabled enables APIC device mode reporting from the BIOS to

the operating system.


MPS Version Control For OS

The BIOS supports version 1.1 and 1.4 of the Intel multiprocessor specification.

Select version supported by the operation system running on this computer.

The Choices: 1.4 (default), 1.1.

OS Select For DRAM > 64MB

A choice other than Non-OS2 is only used for OS2 systems with memory

exceeding 64MB.

The Choices: Non-OS2 (default), OS2.

Small Logo (EPA) Show

This item allows you to select whether the “Small Logo” shows.

Enabled (default)

Disabled

“Small Logo” shows when system boot up.

No “Small Logo” shows when system boots up.

Summary Screen Show

This item allows you to enable/disable the summary screen. Summary

screen means system configuration and PCI device listing.

The Choices: Enabled, Disabled (default).

13

945GC-M7 SE / 945GC Micro 775

4 Advanced Chipset Features

This submenu allows you to configure the specific features of the chipset installed on your system. This chipset manage bus speeds and access to system memory resources, such as

DRAM. It also coordinates communications with the PCI bus. The default settings that came with your system have been optimized and therefore should not be changed unless you are suspicious that the settings have been changed incorrectly.

 Figure 4. Advanced Chipset Setup

DRAM Timing Selectable

When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing.

The Choices: By SPD (default), Manual.

CAS Latency Time

When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing.

The Choices: Auto (default), 3, 4, 5, 6.

DRAM RAS# to CAS# Delay

This field let you insert a timing delay between the CAS and RAS strobe signals, used when DRAM is written to, read from, or refreshed. Fast gives faster performance; and slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system.

The Choices: Auto (default), 2, 3, 4, 5, 6.

14

945GC-M7 SE / 945GC Micro 775

DRAM RAS# Precharge

If an insufficient number of cycles is allowed for RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete, and the

DRAM may fail to retain data. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous

DRAM is installed in the system.

The Choices: Auto (default), 2, 3, 4, 5, 6.

Precharge Delay (TRAS)

This item controls the number of DRAM clocks to activate the precharge delay.

The Choices: Auto (default), 4/5/6/7/8/9/10/11/12/13/14/15.

System Memory Frequency

This item allows you to select the Memory Frequency.

The Choices: Auto (default), 400MHz, 533MHz, and 667MHz.

VGA Setting

PEG/Onchip VGA Control

This item allows you to enabled or disabled PEG/On-chip VGA controller.

The Choices: Auto (default), Onchip VGA, PEG Port.

On-Chip Frame Buffer Size

This item will be different as your memory modules. When the memory size is decided, this frame buffer size will also be fixed.

The Choices: 8MB (default), 1MB.

DVMT Mode

The Choices: DVMT (default), FIXED, BOTH.

DVMT/FIXED Memory Size

DVMT stands for „Dynamic Video Memory Technology“. This is an enhancemnet of the unified memory architecture (UMA) concept. Where the optimum amount of memory is allocated for balanced graphics and system performance. DVMT dynamically reponds to system requirements and applications demands, by allocating the proper amount of display, texturing and buffer memory after the operating system has booted.

The Choices:128MB (Default), 64MB.

Boot Display

The Choices: Auto (default), CRT, TV, EFP.

15

945GC-M7 SE / 945GC Micro 775

SLP S4# Assertion Width

This item sets the minimum assertion width of the SLP-S4# signal to guarantee the DRAM has been safely power-cycled.

The Choices: 4 to 5 Sec. (default), 3 to 4 Sec., 2 to 3 Sec., 1 to 2 Sec.

System BIOS Cacheable

Selecting Enabled allows you caching of the system BIOS ROM at

F0000h~FFFFFh, resulting a better system performance. However, if any program writes to this memory area, a system error may result.


Video BIOS Cacheable

Select Enabled allows caching of the video BIOS, resulting a better system performance. However, if any program writes to this memory area, a system error may result.


Memory Hole At 15M-16M

You can reserve this area of system memory for ISA adapter ROM. When this area is reserved it cannot be cached. The user information of peripherals that need to use this area of system memory usually discussed their memory requirements.


16

945GC-M7 SE / 945GC Micro 775

PCI Express Root Port Func

PCI Express Port 1

This item allows you to select the PCI Express Port.

The Choices: Auto (default), Enabled, Disabled.

PCI-E Compliancy Mode

This item allows you to select the PCI-E Compliancy Mode.

The Choices: v1.0a (default), v1.0.

17

945GC-M7 SE / 945GC Micro 775

5 Integrated Peripherals

 Figure 5. Integrated Peripherals

OnChip IDE Device

If you highlight the literal “Press Enter” next to the “OnChip IDE Device” label and then press the enter key, it will take you a submenu with the following options:

18

945GC-M7 SE / 945GC Micro 775

IDE HDD Block Mode

Block mode is also called block transfer, multiple commands, or multiple sector read / write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block mode

(most new drives do), select Enabled for automatic detection of the optimal number of block read / write per sector where the drive can support.


IDE DMA Transfer Access

This item allows you to enable or disable the IDE transfer access.


On-chip Primary/Secondary PCI IDE

This item allows you to enable or disable the primary/ secondary IDE Channel.


IDE Primary/Secondary Master/Slave PIO

The IDE PIO (Programmed Input / Output) fields let you set a PIO mode (0-4) for each of the IDE devices that the onboard IDE interface supports. Modes 0 to 4 will increase performance progressively. In Auto mode, the system automatically determines the best mode for each device.

The Choices: Auto (default), Mode0, Mode1, Mode2, Mode3, and Mode4.

IDE Primary/Secondary Master/Slave UDMA

Ultra DMA/100 functionality can be implemented if it is supported by the IDE hard drives in your system. As well, your operating environment requires a DMA driver

(Windows 95 OSR2 or a third party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/100, select Auto to enable BIOS support.


SATA Mode

The Choices: IDE (default), RAID, AHCI.

On-Chip Serial ATA

This item allows you to choose:

Disabled: disabled SATA Controller

Combined Mode: PATA and SATA are combined max of 2 IDE drivers in each channel.

Enhanced Mode: enabled both SATA and PATA max of 6 IDE drivers are supported.

SATA Only: SATA is operating in legacy mode.

The Choices: Disabled, Auto, Combined Mode, Enhanced Mode (default), and SATA only.

19

945GC-M7 SE / 945GC Micro 775

SATA PORT Speed Settings

The Choices: Disabled (default), Force GEN I, Force GEN II.

PATA IDE Mode

The Choices: Primary (default), Secondary.

Onboard Device

If you highlight the literal “Press Enter” next to the “Onboard Device” label and then press the enter key, it will take you a submenu with the following options:

USB Controller

Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have USB peripherals.

The Choices: Enabled (default), Disabled

USB 2.0 Controller

This entry is to enable or disable EHCI controller only. This BIOS itself may/ may not have high speed USB support. If the BIOS has high speed USB support built in, the support will automatically turn on, when high speed device were attached.


USB Keyboard Support

This item allows you to enable or disable the USB Keyboard Legacy Support.

Enabled Enable USB Keyboard Support.

Disabled (default) Disable USB Keyboard Support.

20

945GC-M7 SE / 945GC Micro 775

USB Mouse Support

This item allows you to enable or disable the USB Mouse Legacy Support.

Enabled Enable USB Mouse Support.

Disabled (default) Disable USB Mouse Support.

Onboard AC97 Audio

This item allows you to decide to enable or disable to support AC97 Audio.


Onboard LAN

This item allows you to enable or disable the Onboard LAN.


Onboard LAN Boot ROM

This item allows you to enable or disable the Onboard LAN Boot ROM.


Super IO Device

Press Enter to configure the Super I/O Device.

Onboard FDC Controller

Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If install and FDC or the system has no floppy drive, select

Disabled in this field.


Onboard Serial Port 1

Select an address and corresponding interrupt for the first and second serial ports.

The Choices: Disabled, 3F8/IRQ4 (default), 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Auto.

21

945GC-M7 SE / 945GC Micro 775

Onboard Parallel Port

This item allows you to determine access onboard parallel port controller with which

I/O Address.

The Choices: 378/IRQ7 (default), 278/IRQ5, 3BC/IRQ7, Disabled.

Parallel Port Mode

The default value is SPP.

The Choices:

SPP (default)

EPP

ECP

ECP+EPP

Using Parallel port as Standard Printer Port.

Using Parallel Port as Enhanced Parallel Port.

Using Parallel port as Extended Capabilities Port.

Using Parallel port as ECP & EPP mode.

ECP Mode Use DMA

Select a DMA Channel for the port.

The Choices: 3 (default), 1.

PWRON After PWR-Fail

This setting specifies whether your system will reboot after a power fail or interrupts occurs.

Off Leaves the computer in the power off state.

On Reboots the computer.

Former-Sts Restores the system to the status before power failure or interrupt occurs.

The Choices: Off (default), On, Former-Sts.

22

945GC-M7 SE / 945GC Micro 775

6 Power Management Setup

The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up/power down features.

Figure 6. Power Management Setup

ACPI & Wake Up Events

23

945GC-M7 SE / 945GC Micro 775

ACPI Function

This item displays the status of the Advanced Configuration and Power Management

(ACPI).


ACPI Suspend Type

The item allows you to select the suspend type under the ACPI operating system.

The Choices: S1 (POS) (default)

S3 (STR)

S1 & S3

Power on Suspend

Suspend to RAM

POS+STR

Run VGABIOS if S3 Resume

Choosing Enabled will make BIOS run VGA BIOS to initialize the VGA card when system wakes up from S3 state. The system time is shortened if you disable the function, but system will need AGP driver to initialize the card. So, if the AGP driver of the VGA card does not support the initialization feature, the display may work abnormally or not function after S3.

The Choices: Auto (default), Yes, No.

Wake-Up by PCI card

When you select “Enable”, a PME signal from PCI card returns the system to

Full On state.

The Choices: Enabled, Disabled (default).

Power On by Ring

An input signal on the serial Ring Indicator (RI) line (in other words, an incoming call on the modem) awakens the system from a soft off state.

The Choices: Enabled, Disabled (default).

USB KB/MS Wake-Up From S3

This item allows you to enable or disable USB keyboard wake up from S3.


Resume by Alarm

This function is for setting date and time for your computer to boot up.

During Disabled, you cannot use this function. During Enabled,

Choose the Date and Time.

Date (of Month) Alarm

You can choose which month the system will boot up.

Time (hh:mm:ss) Alarm

You can choose shat hour, minute and second the system will boot up.

Note: If you have changed the setting, you must let the system boot up until it goes to the operating system, before this function will work.

24

945GC-M7 SE / 945GC Micro 775

POWER ON Function

This item allows you to choose the power on function.

The Choices: Button Only (default), Password, Hot Key, Mouse Move/Click, Mouse

Double Click, Any Key, Keyboard 98.

KB POWER ON Password

Input password and press Enter to set the Keyboard power on password.

Hot Key Power ON

Input password and press Enter to set the Keyboard power on password.

The Choices: Ctrl-F1 (default), Ctrl-F2, Ctrl-F3, Ctrl-F4, Ctrl-F5,

Ctrl-F6, Ctrl-F7, Ctrl-F8, Ctrl-F9, Ctrl-F10, Ctrl-F11, and Ctrl-F12.

Reload Timer Events

Primary/Secondary IDE 0/1

You can select to enable or disable Primary or Secondary RAID 0 or

RAID 1 function under this item.


FDD, COM, LPT Port

You can select to enable or disable FDD, COM, and LPT port under this item.


PCI PIRQ [A-D]#

You can select to enable or disable PCI PIRQ [A-D]# under this item.


25

945GC-M7 SE / 945GC Micro 775

Power Management

This category allows you to select the type (or degree) of power saving and is directly related to the following modes:

1. HDD Power Down.

2. Suspend Mode.

There are four options of Power Management, three of which have fixed mode settings

Min Saving (default)

Minimum power management.

Suspend Mode = 1 hr.

HDD Power Down = 15 min

Max. Saving

Maximum power management only available for sl CPU’s.

Suspend Mode = 1 min.

HDD Power Down = 1 min.

User Define

Allows you to set each mode individually.

When not disabled, each of the ranges is from 1 min. to 1 hr. Except for HDD

Power Down which ranges from 1 min. to 15 min. and disable.

Video Off Method

This option determines the manner in which the monitor is goes blank.

The Choices: DPMS (default), Blank Screen, V/H SYNC+Blank.

Video Off In Suspend

This determines the manner in which the monitor is blanked.

The Choices: Yes (default), No.

Suspend Type

Select the Suspend Type.

The Choices: Stop Grant (default), PwrOn Suspend.

Modem Use IRQ

This determines the IRQ, which can be applied in MODEM use.

The Choices: 3 (default), 4 / 5 / 7 / 9 / 10 / 11 / NA.

26

945GC-M7 SE / 945GC Micro 775

Suspend Mode

The item allows you to select the suspend type under ACPI operating system.

The Choices: Disabled, 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min, 20 Min, 30 Min, 40

Min, 1 Hour (default).

This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer.

Blank Screen

This option only writes blanks to the video buffer.

HDD Power Down

When enabled, the hard disk drive will power down and after a set time of system inactivity. All other devices remain active.

The Choices: Disabled, 1 Min, 2 Min, 3 Min, 4 Min, 5 Min, 6 Min, 7 Min, 8 Min, 9 Min,

10 Min, 11 Min, 12 Min, 13 Min, 14 Min, 15 Min (default).

Soft-Off by PWR-BTN

Pressing the power button for more than 4 seconds forces the system to enter the

Soft-Off state when the system has “hung.”

The Choices: Delay 4 Sec, Instant-Off (default).

HPET Support

This item allows you to enable or disable HPET.


HPET Mode

This item allows you to select the HPET mode.

The Choices: 32-bit mode (default), 64-bit mode.

27

945GC-M7 SE / 945GC Micro 775

7 PnP/PCI Configurations

This section describes configuring the PCI bus system. PCI, or Personal Computer

Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.

 Figure 7. PnP/PCI Configurations

Init Display First

This item allows you to decide to active whether PCI Slot or on-chip VGA first.

The Choices: PCI Slot (default), PCIEx, Onboard.

Resources Controlled By

By Choosing “Auto (ESCD)” (default), the system BIOS will detect the system resources and automatically assign the relative IRQ and DMA channel for each peripheral. By Choosing “Manual”, the user will need to assign IRQ & DMA for add-on cards. Be sure that there are no IRQ/DMA and I/O port conflicts.

The Choices: Auto (default), Manual.

28

945GC-M7 SE / 945GC Micro 775

IRQ Resources

This submenu will allow you to assign each system interrupt a type, depending on the type of device using the interrupt. When you press the

“Press Enter” tag, you will be directed to a submenu that will allow you to configure the system interrupts. This is only configurable when

“Resources Controlled By” is set to “Manual”.

IRQ-3 assigned to PCI Device










PCI / VGA Palette Snoop

Choose Disabled or Enabled. Some graphic controllers that are not VGA compatible take the output from a VGA controller and map it to their display as a way to provide boot information and VGA compatibility.

However, the color information coming from the VGA controller is drawn from the palette table inside the VGA controller to generate the proper colors, and the graphic controller needs to know what is in the palette of the VGA controller. To do this, the non-VGA graphic controller watch for the Write access to the VGA palette and registers the snoop data. In PCI based systems, where the VGA controller is on the PCI bus and a non-VGA graphic controller is on an ISA bus, the Write Access to the palette will not show up on the ISA bus if the PCI VGA controller responds to the Write.

In this case, the PCI VGA controller should not respond to the Write, it should only snoop the data and permit the access to be forwarded to the

ISA bus. The non-VGA ISA graphic controller can then snoop the data on the ISA bus. Unless you have the above situation, you should disable this option.

Disabled (default) Disable the function.

Enabled Enable the function.

Maximum Payload Size

Set the maximum payload size for Transaction packets (TLP).

The Choice: 4096 (default.), 128, 256, 512, 1024, 2048.

29

945GC-M7 SE / 945GC Micro 775

8 PC Health Status

 Figure 8. PC Health Status

CPU FAN Control

The Choice “smart” can make your CPU FAN to reduce noise.

The Choices: Smart (default), Always On.

CPU Fan Off<℃>

If the CPU Temperature is lower than the set value, FAN will turn off.

The Choices: Min=0,.Max=127, Key in a DEC number.

CPU Fan Start<℃>

CPU fan starts to work under smart fan function when arrive this set value.


CPU Fan Full speed <℃>

When CPU temperature is reach the set value, the CPU fan will work under Full Speed.


Start PWM Value

When CPU temperature arrives to the set value, the CPU fan will work under Smart Fan

Function mode. The range is from 0~127, with an interval of 1.


30

945GC-M7 SE / 945GC Micro 775

SHUTDOWN TEMPERATURE

This item allows you to set up the CPU shutdown Temperature. This item only effective under Windows 98 ACPI mode

The Choices: 65

O

C/140

O

F, 70

O

C/149

O

F, 75

O

C/158

O

F, Disabled (default).

SHOW H/W MONITOR IN POST

If you computer contain a monitoring system, it will show PC health status during POST stage. The item offers several delay time to select you want.


CPU VCORE, NB/SB VOLTAGE, +3.3V, +5.0V, 12.0V, 5V(SB),VOLTAGE

BATTERY

Detect the system’s voltage status automatically.

CURRENT CPU TEMP

This field displays the current temperature of CPU.

CURRENT CPU FAN SPEED

This field displays the current speed of CPU fan.

CURRENT SYS FAN SPEED

This field displays the current speed SYSTEM fan.

31

945GC-M7 SE / 945GC Micro 775

9 Performance Booster Zone

 Figure 9. Performance Booster Zone

CPU Voltage

This item allows you to select CPU Voltage Control.

The Choices: StartUp (default), +0.012V~+0.787V.

Memory Voltage

The Choices:1.80V (default), 1.90V, 2.00V, 2.10V, 2.20V, 2.30V, 2.40V, 2.50V.

FSB Termination Voltage

The Choices: 1. 2V (default), 1.3V, 1.4V, 1.5V.

CPU Clock Ratio

This item allows you to select the CPU Ratio.

Min = 8 Max = 50 Key in a DEC number.

The Choices: 8X (default).

CPU Clock

This item allows you to select CPU Clock, and CPU over clocking.

Min= 100 Max = 265 Key in a DEC number.

The Choices: 100Mhz (default).

32

945GC-M7 SE / 945GC Micro 775

PCIE Clock select

The Choices: Fixed 100 (default), Upto CPU, Manual

PCIE Clock

Display the PCIE Clock frequency; Min=100, Max=200, key in a DEC number.

This option is configurable only when “PCIE Clock Select” is set to “Manual”.

PCI Clock

The Choices: 33.33 (default) ~ 37.50

Special Notice:

If unfortunately, the system’s frequency that you are selected is not functioning, there are two methods of booting-up the system.

Method 1:

Clear the COMS data by setting the JCOMS1 ((2-3) closed)) as “ON” status. All the CMOS data will be loaded as defaults setting.

Method 2:

Press the <Insert> key and Power button simultaneously, after that keep-on pressing the <Insert> key until the power-on screen showed.

This action will boot-up the system according to FSB of the processor

It’s strongly recommended to set CPU Vcore and clock in default setting. If the CPU

Vcore and clock are not in default setting, it may cause CPU or M/B damage.

33

User's manual | Biostar 945GC MICRO 775 User`s manual

FCC Information and Copyright

EFORE

OU

TART

ACKAGE

HECKLIST

OTHERBOARD

EATURES

EAR

ANEL

ONNECTORS

FOR

ER

X

EAR

ANEL

ONNECTORS

FOR

ER

X

OTHERBOARD

AYOUT

FOR

Intel

945GC

OTHERBOARD

AYOUT

FOR

ICRO

Intel

945GC

NSTALLING

ENTRAL

ROCESSING

NIT

Special Notice:

EADERS

JCFAN1: CPU Fan Header

JSFAN1: System Fan Header

NSTALLING

YSTEM

EMORY

A. DDR2 module

B. Memory Capacity

C. Dual Channel Memory installation

ONNECTORS AND

LOTS

FDD1: Floppy Disk Connector

IDE1: Hard Disk Connectors

PEX16_1: PCI-Express x16 Slot

PEX1_1: PCI-Express x1 Slot

PCI1~PCI2: Peripheral Component Interconnect Slots

OW TO

ETUP

UMPERS

ETAIL

ETTINGS

JPANEL1: Front Panel Header

JATXPWR1: ATX Power Source Connector

JATXPWR2: ATX Power Source Connector

JUSB3/JUSB4: Headers for USB 2.0 Ports at Front Panel

SATA1~SATA4: Serial ATA Connectors

JSPDIF_OUT: Digital Audio out Connectors

JAUDIOF1: Front Panel Audio Header

JCDIN1: CD-ROM Audio-in Connector

JCMOS1: Clear CMOS Header

※ Clear CMOS Procedures:

JKBV1: Power Source Header for PS/2 Keyboard and Mouse

(Only for 945GC Micro 775)

JUSBV1/JUSBV3_1: Power Source Headers for USB Ports

(Only for 945GC Micro 775)

JPRNT1: Printer Port Connector

RIVER

NSTALLATION

OTE

A. Driver Installation

B. Software Installation

C. Manual

WARD