Digital Watchdog Infinity C233W User manual
Add to My manuals10 Pages
Digital Watchdog Infinity C233W is a high-resolution camera with 560 TV lines and 1/3” Sony Super HAD II CCD, providing clear images in both bright and dark environments. It features True Day & Night functionality, Star-Light (Super Low Light Technology), and Max-DR (Electronic Wide Dynamic Range) for excellent image quality in various lighting conditions. The 3D-DNR (3D Digital Noise Reduction) reduces noise and enhances color in low-light settings. It also has six programmable privacy zones and motion detection capabilities for enhanced security.
advertisement
Infinity C233W
User Manual Version #2:
Camera with ICON Menu
11192010
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenance and installation, for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may rise to high levels.
Cleaning
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
Provide reasonable protection against harmful interference .when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacture.
TROUBSHOOTING
Before sending your camera for repair, check the following or contact our technical specialist.
No VIDEO
Check the coaxial cable and make sure it is connected securely.
Check the lens’ iris adjustment at the menu setup of the camera.
Check the power supply and make sure the camera has the proper voltage and current.
Out-of-Focus VIDEO
Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean.
Check the lens manual focal and zoom adjustment. Field test monitor is recommended.
FEATURES
1/3” Sony Super HAD II CCD
High Resolution 560 TV Lines
True Day & Night / TDN5 (Electro Magnetic Mechanism)
Star-Light (Super Low Light Technology)
Max-DR (Electronic Wide Dynamic Range)
Enables the camera to capture perfect images in both bright and dark environments simultaneously.
3D-DNR (3D Digital Noise Reduction)
Produces less noise and more color during low-light application.
HME (Highlight Mask Exposure)
Masks overly exposed light to produce a true video image of any environment.
SLC (Side Light Compensation)
DIS (Digital Image Stabilizer)
Programmable Privacy Zone (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Negative Imaging
Mirror Image Control
Auto Sensing 12VDC or 24VAC with Line Lock
No Fog or Condensation under Any Weather Condition
ADJUSTMENT OF BACK FOCUS
1. Please make sure the lens is C or CS Mount.
To use C Mount lens, please fix the lens into front camera after mounting the included C ring to the lens.
To use CS Mount lens, fix the lens directly into the front camera without the C ring.
2. To adjust the focus, slide the focus lever on the side of the front camera.
3. Please tighten the focus lever after the adjustment in order to prevent being out of focus.
DIMENSIONS (mm)
LENS
SHUTTER
BLC
AGC
MAX-DR
STAR-LIGHT
EXIT JUMP
WB MODE
R-Y GAIN
B-Y GAIN
Day & Night Mode
C-SUP
A-SUP
EXIT JUMP
EXPOSURE
DC (0~100) / MANUAL / VIDEO. (DC Lens is recommended.)
1/160 /1/100 / FLC / 1/250 ~ 10000 / SENS-UP x2 ~ x250
OFF / ON
BLC (Back Light Compensation)
HIGH / MIDDLE / LOW / OFF
AGC (Auto Gain Control)
OFF / ON (0 ~ 20) (Electronic Wide Dynamic Range)
AUTO (x2 ~ x250) / OFF (x32 is recommended.)
EXIT / SAVE&EXIT / FACTORY RESET
COLOR
AWC / ATW / MANUAL / PUSH LOCK
0 ~ 100
0 ~ 100
AUTO / COLOR / BW / EX-CONT
DAY & NIGHT
COLOR ---- BW : Switching from color to BW; if the number is higher, the camera will only switch during a super low light condition.
BW ---- COLOR : Switching from BW to color; this number should always be lower than COLOR to BW
Read Time: Time interval to switch from Color to Black-and-White
COLOR
B&W: (BURST:OFF/ON) When the burst is OFF will make less noise
Color Suppression :Color will be reduced at low illumination, if the C-SUP Level is higher.
0 ~ 100 (Not Available when DNR is On.)
Aperture Suppression: The sharpness of the edges will be reduced at low illumination, if A-SUP Level is higher.
0 ~ 100 (Not Available when DNR is On.)
EXIT / SAVE&EXIT / FACTORY SET
MIRROR
SHARPNESS
GAMMA
FREEZE
NEGATIVE
3D-DNR
D-ZOOM
SLC
HME
DIS
EXIT JUMP
MOTION
EXIT JUMP
FUNCTION
OFF / MIRROR / V-FLIP / ROTATE
0 ~ 31
0.05 ~ 1.00 / USER
OFF / ON
OFF/ ON
OFF / LOW / MIDDLE / HIGH
3D-DNR (3D Digital Noise Reduction)
OFF / ON (x1.0 ~ x32 PTZ)
OFF / ON
SLC (Side Light Compensation)
OFF / ON
HME (Highlight Masking Exposure)
OFF / ON
DIS (Digital Image Stabilizer)
EXIT / SAVE&EXIT / FACTORY SET
MOTION
(OMNI-Focus Lens Only)
OFF / ON
SET WINDOW
ALL SET (Set the Entire Screen)
ALL CLEAR (Clear the Entire Screen)
SENSITIVITY (1 ~ 120)
SHOW INDICATOR (OFF / ICON / TRACE)
DELAY OUT (1 ~ 15)
Motion Alarm Zoom-In Delay
EXIT / SAVE&EXIT / FACTORY SET
EXIT JUMP
CAMERA ID
TITLE
DPC
MONITOR
LANGUAGE
BAUDRATE
OMNI LENS
EXIT JUMP
PRIVACY
MASK 1 OFF / ON
MASK 2 OFF / ON
MASK 3 OFF / ON
MASK 4 OFF / ON
MASK 5 OFF / ON
MASK 6 OFF / ON
EXIT / SAVE&EXIT / FACTORY SET
SETUP
0 ~ 255
OFF / ON
OFF / AUTO
DPC (Dead Pixels Cancellation)
CRT / LCD
English, Japanese, Chinese
2400 / 4800 / 9600 / 14400 / 19200 / 38400.
Protocol is Pelco-D (fixed cannot be changed; hardcoded into the DSP)
OFF / 1 ~ 10 (for OMNI-PLUS CAMERA only)
EXIT / SAVE&EXIT / FACTORY SET
SYNC
V-PHASE
EXIT JUMP
EXIT
SAVE&EXIT
FACTORY SET
SYNC
INTERNAL / AUTO
0 ~ 199
EXIT / SAVE & EXIT / FACTORY SET
Exit the menu
Exit the menu and save the setting
Reset the menu setting to factory default
EXIT
SPECIFICATIONS:
5436 W Crenshaw St. Tampa, FL 33634
Tel: 866-446-3595 / 813-888-9555
Fax: 813-888-9262 www.Digital-Watchdog.com
Technical Support Hours: Monday-Friday
8:30am to 8:00pm Eastern Time
Camera TYPE
Image
Scanning
Min. Scene Illumination
Functions
Lens
Resolution
Video Output
S/N Ratio
OSD
Environmental Conditions
Power
Color / BW
Mount
Device
Size
Pixels-Total
Pixels-Effective
System
Horizontal Frequency Internal Mode
Vertical Frequency Internal Mode
F1.2
x256 Star-Light
BLC
AGC
MAX-DR
Mirror
STAR-LIGHT
3D-DNR
SLC
HME
DIS
Privacy Zone
Focal Length
Horizontal
VBS 1.0Vp-p
S/N Ratio
OSD
Operating Temperature
Humidity
Power Requirement
Power Consumption
C233W
3D Bracket
Super HAD II CCD
1/3"
811(H) x 508 (V)
768(H) x 494 (V)
525 line, 2:1Interlace
15,734Hz
59.94Hz
0.14 Lux
0.0005 Lux in Color
ON / OFF
HIGH / MIDDLE / LOW /OFF
OFF / ON
OFF / MIRROR / V-FLIP / ROTATE
AUTO (x2 ~ x250) / OFF
OFF / ON
OFF / ON
OFF / ON
OFF / ON
6 Programmable Zone / Size
3.3~12mm Varifocal Auto Iris Lens
560 TV Lines [Color]; 580 TV Lines [BW]
VBS 1.0Vp-p(75 Load)
50dB
YES
-10℃ ~ +55℃(14℉ ~ 131℉)
Less than 90%
12VDC / 24VAC
1.8 [W] / 2.4 [W]
advertisement
Related manuals
advertisement