Red Hat Virtualization Installation Guide
Reklamë
Reklamë
Red Hat Enterprise Virtualization
3.0
Installation Guide
Installing Red Hat Enterprise Virtualization Environments
Edition 5
Stephen Gordon Tim Hildred
Red Hat Enterprise Virtualization 3.0 Installation Guide
Installing Red Hat Enterprise Virtualization Environments
Edition 5
Stephen Go rdo n
Red Hat Engineering Co ntent Services
Tim Hildred
Red Hat Engineering Co ntent Services
Legal Notice
Copyright © 2011 Red Hat, Inc.
This document is licensed by Red Hat under the
Creative Commons Attribution-ShareAlike 3.0 Unported
License
. If you distribute this document, or a modified version of it, you must provide attribution to Red
Hat, Inc. and provide a link to the original. If the document is modified, all Red Hat trademarks must be removed.
Red Hat, as the licensor of this document, waives the right to enforce, and agrees not to assert, Section
4d of CC-BY-SA to the fullest extent permitted by applicable law.
Red Hat, Red Hat Enterprise Linux, the Shadowman logo, JBoss, MetaMatrix, Fedora, the Infinity Logo, and RHCE are trademarks of Red Hat, Inc., registered in the United States and other countries.
Linux ® is the registered trademark of Linus Torvalds in the United States and other countries.
Java ® is a registered trademark of Oracle and/or its affiliates.
XFS ® is a trademark of Silicon Graphics International Corp. or its subsidiaries in the United States and/or other countries.
MySQL ® is a registered trademark of MySQL AB in the United States, the European Union and other countries.
Node.js ® is an official trademark of Joyent. Red Hat Software Collections is not formally related to or endorsed by the official Joyent Node.js open source or commercial project.
The OpenStack ® Word Mark and OpenStack Logo are either registered trademarks/service marks or trademarks/service marks of the OpenStack Foundation, in the United States and other countries and are used with the OpenStack Foundation's permission. We are not affiliated with, endorsed or sponsored by the OpenStack Foundation, or the OpenStack community.
All other trademarks are the property of their respective owners.
Abstract
Red Hat Enterprise Virtualization 3.0 Installation Guide
Table of Contents
3. Getting Help and Giving Feedback
1.1.1. About the Virtual Machines
2.1.1. Management Server Requirements
2.1.2. Virtualization Host Requirements
2.1.2.4. PCI Device Requirements
2.2.3.2. Red Hat Network Configuration
2.2.5.1. Red Hat Enterprise Virtualization Manager Firewall Requirements
2.2.5.2. Virtualization Host Firewall Requirements
2.2.5.3. Directory Firewall Requirements
2.2.6.1. Required UIDs and GIDs
3.3. Removing Red Hat Enterprise Virtualization Manager
3.4. Connect to the Administration Portal
Table of Contents
17
17
17
17
18
18
18
14
14
15
15
16
16
19
20
20
21
23
23
23
10
11
11
11
26
26
31
31
8
8
7
7
8
5
5
5
5
5
1
Red Hat Enterprise Virtualization 3.0 Installation Guide
7.1.1. Preparation Instructions
7.1.2. Preparing a Hypervisor USB Storage Device
7.1.2.1. Making a USB Storage Device into a Hypervisor Boot Device
7.1.2.1.1. Using rhevh-iso-to-disk to Create USB Install Media
7.1.2.1.2. Using dd to Create USB Install Media
7.1.2.2. Booting a Hypervisor USB Storage Device
7.1.3. Preparing a Hypervisor from a CD-ROM or DVD
7.1.3.1. Making a Hypervisor CD-ROM Boot Disk
7.1.3.2. Booting a Hypervisor CD-ROM
7.2.1. Interactive Installation
7.2.1.1. Booting from the Installation Media
7.2.1.2. Installation Procedure
8.1. Adding Red Hat Enterprise Linux Hosts
8.1.1. Preparing Red Hat Enterprise Linux Hosts
2
9.1.1. Prerequisites for Setting up a Data Center
9.1.2. Working with Data Centers
9.1.3. Creating a New Data Center
10.1. Determine Network Requirements
10.2.1. Adding Logical Networks
10.2.1.1. Designate Display Network
11.1. Storage Domains Overview
51
51
52
52
52
53
56
44
45
47
47
47
48
51
61
62
63
63
58
58
58
58
61
64
65
67
67
71
73
82
83
83
85
86
86
76
76
77
77
79
79
90
11.1.2.1. Mapping iSCSI Targets to LUNs
11.2.1. Uploading the VirtIO and Guest Tool Image Files
A.1. Red Hat Enterprise Virtualization Manager Log Files
Table of Contents
90
94
96
96
98
99
99
102
102
103
104
104
105
111
112
114
114
114
118
107
107
108
110
110
111
3
4
Red Hat Enterprise Virtualization 3.0 Installation Guide
Preface
Preface
The Red Hat Enterprise Virtualization platform is a richly featured virtualization management solution providing fully integrated management across virtual machines. It is based on the leading open source virtualization platform and provides superior technical capabilities. The platform offers scalable management of large numbers of virtual machines.
1. About this Guide
1.1. Audience
This guide is intended to provide detailed instruction on the installation and configuration of Red Hat
Enterprise Virtualization. A background in the administration of systems running Red Hat Enterprise
Linux is recommended. Experience with previous versions of Red Hat Enterprise Virtualization, while beneficial, is not required.
Customers with an Evaluation license should, in the first instance, consult the Evaluation Guide for a more streamlined installation experience. This guide will discuss all installation options in their entirety.
1.2. Overview
Completion of the procedures outlined within this guide will result in a working Red Hat Enterprise
Virtualization environment. The environment produced will be configured to the level such that it can be used to create, run, and manage virtual machines.
2. Document Conventions
This manual uses several conventions to highlight certain words and phrases and draw attention to specific pieces of information.
In PDF and paper editions, this manual uses typefaces drawn from the Liberation Fonts set. The
Liberation Fonts set is also used in HTML editions if the set is installed on your system. If not, alternative but equivalent typefaces are displayed. Note: Red Hat Enterprise Linux 5 and later include the Liberation
Fonts set by default.
2.1. Typographic Conventions
Four typographic conventions are used to call attention to specific words and phrases. These conventions, and the circumstances they apply to, are as follows.
Mono-spaced Bold
Used to highlight system input, including shell commands, file names and paths. Also used to highlight keys and key combinations. For example:
To see the contents of the file my_next_bestselling_novel in your current working directory, enter the cat my_next_bestselling_novel command at the shell prompt and press Enter to execute the command.
The above includes a file name, a shell command and a key, all presented in mono-spaced bold and all distinguishable thanks to context.
Key combinations can be distinguished from an individual key by the plus sign that connects each part of a key combination. For example:
5
Red Hat Enterprise Virtualization 3.0 Installation Guide
Press Enter to execute the command.
Press Ctrl+Alt+F2 to switch to a virtual terminal.
The first example highlights a particular key to press. The second example highlights a key combination: a set of three keys pressed simultaneously.
If source code is discussed, class names, methods, functions, variable names and returned values mentioned within a paragraph will be presented as above, in mono-spaced bold. For example:
File-related classes include filesystem for file systems, file for files, and dir for directories. Each class has its own associated set of permissions.
Proportional Bold
This denotes words or phrases encountered on a system, including application names; dialog box text; labeled buttons; check-box and radio button labels; menu titles and sub-menu titles. For example:
Choose System → Preferences → Mouse from the main menu bar to launch Mouse
Preferences. In the Buttons tab, select the Left-handed mouse check box and click
Close to switch the primary mouse button from the left to the right (making the mouse suitable for use in the left hand).
To insert a special character into a gedit file, choose Applications → Accessories →
Character Map from the main menu bar. Next, choose Search → Find… from the
Character Map menu bar, type the name of the character in the Search field and click
Next. The character you sought will be highlighted in the Character T able. Double-click this highlighted character to place it in the Text to copy field and then click the Copy button. Now switch back to your document and choose Edit → Paste from the gedit menu bar.
The above text includes application names; system-wide menu names and items; application-specific menu names; and buttons and text found within a GUI interface, all presented in proportional bold and all distinguishable by context.
Mono-spaced Bold Italic or Proportional Bold Italic
Whether mono-spaced bold or proportional bold, the addition of italics indicates replaceable or variable text. Italics denotes text you do not input literally or displayed text that changes depending on circumstance. For example:
To connect to a remote machine using ssh, type ssh username@domain.name at a shell prompt. If the remote machine is example.com and your username on that machine is john, type ssh [email protected].
The mount -o remount file-system command remounts the named file system. For example, to remount the /home file system, the command is mount -o remount /home.
To see the version of a currently installed package, use the rpm -q package command. It will return a result as follows: package-version-release.
Note the words in bold italics above — username, domain.name, file-system, package, version and release. Each word is a placeholder, either for text you enter when issuing a command or for text displayed by the system.
Aside from standard usage for presenting the title of a work, italics denotes the first use of a new and
6
Preface important term. For example:
Publican is a DocBook publishing system.
2.2. Pull-quote Conventions
Terminal output and source code listings are set off visually from the surrounding text.
Output sent to a terminal is set in mono-spaced roman and presented thus: books Desktop documentation drafts mss photos stuff svn books_tests Desktop1 downloads images notes scripts svgs
Source-code listings are also set in mono-spaced roman but add syntax highlighting as follows: static int kvm_vm_ioctl_deassign_device( struct kvm *kvm, struct kvm_assigned_pci_dev *assigned_dev)
{ int r = 0; struct kvm_assigned_dev_kernel *match;
mutex_lock(&kvm->lock);
match = kvm_find_assigned_dev(&kvm->arch.assigned_dev_head,
assigned_dev->assigned_dev_id); if (!match) {
printk(KERN_INFO "%s: device hasn't been assigned before, "
"so cannot be deassigned \n " , __func__);
r = -EINVAL; goto out;
}
kvm_deassign_device(kvm, match);
kvm_free_assigned_device(kvm, match); out:
mutex_unlock(&kvm->lock); return r;
}
2.3. Notes and Warnings
Finally, we use three visual styles to draw attention to information that might otherwise be overlooked.
Note
Notes are tips, shortcuts or alternative approaches to the task at hand. Ignoring a note should have no negative consequences, but you might miss out on a trick that makes your life easier.
7
Red Hat Enterprise Virtualization 3.0 Installation Guide
Important
Important boxes detail things that are easily missed: configuration changes that only apply to the current session, or services that need restarting before an update will apply. Ignoring a box labeled 'Important' will not cause data loss but may cause irritation and frustration.
Warning
Warnings should not be ignored. Ignoring warnings will most likely cause data loss.
3. Getting Help and Giving Feedback
3.1. Do You Need Help?
If you experience difficulty with a procedure described in this documentation, visit the Red Hat Customer
Portal at http://access.redhat.com
. Through the customer portal, you can: search or browse through a knowledgebase of technical support articles about Red Hat products.
submit a support case to Red Hat Global Support Services (GSS).
access other product documentation.
Red Hat also hosts a large number of electronic mailing lists for discussion of Red Hat software and technology. You can find a list of publicly available mailing lists at https://www.redhat.com/mailman/listinfo .
Click on the name of any mailing list to subscribe to that list or to access the list archives.
3.2. We Need Feedback!
If you find a typographical error in this manual, or if you have thought of a way to make this manual better, we would love to hear from you! Please submit a report by email to the author of the manual,
Stephen Gordon ( [email protected]
). When submitting a bug report, be sure to mention the manual's identifier: Red_Hat_Enterprise_Virtualization-Installation_Guide.
If you have a suggestion for improving the documentation, try to be as specific as possible when describing it. If you have found an error, include the section number and some of the surrounding text so we can find it easily.
8
Part I. Before you Begin
Part I. Before you Begin
9
Red Hat Enterprise Virtualization 3.0 Installation Guide
Chapter 1. Overview
Red Hat Enterprise Virtualization provides IT departments with the tools to meet the challenges of managing complex environments. Red Hat's state-of-the-art virtualization platform enables administrators to reduce the cost and complexity of large deployments. Red Hat Enterprise Virtualization platform provides:
High availability to quickly configure virtual machines for fault tolerance.
Live migration to move virtual machines between physical hosts without interruption.
System scheduler to create policies to dynamically balance compute resources.
Power saver to create policies to conserve power and cooling costs.
Image manager to create, manage and provision virtual machines.
Storage virtualization to consistently access common storage from any server.
Multi-level administration to enable administration of physical infrastructure as well as administration of virtual objects.
Ability to convert existing virtual machines on foreign hypervisors to Red Hat Enterprise Virtualization platform.
A range of reports either from the reports module based on JasperReports, or from the data warehouse. The reports enable administrators to monitor and analyze information on virtual machines, hosts and storage usage and performance.
1.1. System Components
Red Hat Enterprise Virtualization platform consists of one or more hosts (either Red Hat Enterprise
Virtualization Hypervisors or Red Hat Enterprise Linux 6.2, or higher, systems) and at least one manager. The virtual machines are hosted on the hosts. The system and all its components are managed through a centralized management system.
Red Hat Enterprise Virtualization Manager
The Red Hat Enterprise Virtualization Manager acts as a centralized management system that allows system administrators to view and manage virtual machines and images. The Red Hat
Enterprise Virtualization Manager provides a comprehensive range of features including search capabilities, resource management, live migrations and provisioning. The Red Hat Enterprise
Virtualization Manager itself also runs on Red Hat Enterprise Linux 6.
The manager provides a graphical user interface to administer the physical and logical resources within the virtual environment infrastructure. It can be used to manage provisioning, connection protocols, user sessions, virtual machine pools, images and high availability/clustering. The Red Hat Enterprise Virtualization Manager exposes an
Administration Portal, a User Portal, and an Application Programming Interface (API).
The Administration Portal is used to perform setup, configuration, and management of the
Red Hat Enterprise Virtualization environment.
The User Portal is used to start, stop, reboot, and connect to virtual machines. Users granted power user access by the environment's administrators are also able to create virtual machine templates and, virtual machines from this interface.
The REST API provides and interface for automation of tasks normally accomplished manually by users. Scripts that make use of the REST API are able to be written in any language which supports accessing HTTP and HTTPS resources.
Red Hat Enterprise Virtualization Hypervisor(s)
10
Chapter 1. Overview
The Red Hat Enterprise Virtualization Hypervisor is a fully featured virtualization platform for quick, easy deployment and management of virtualized guests. The Hypervisor is designed for management via the Red Hat Enterprise Virtualization Manager. It provides a thin virtualization layer deployed across the server infrastructure.
Kernel-based Virtual Machine (KVM), which is a core component of the Linux kernel, is used to provide virtualization. Red Hat Enterprise Virtualization Hypervisor 6 and later are supported by this release of Red Hat Enterprise Virtualization.
Red Hat Enterprise Linux Host(s)
The Red Hat Enterprise Virtualization Manager also supports the use of systems running Red
Hat Enterprise Linux 6.2, or higher, AMD64/Intel 64 versions as virtualization hosts.
1.1.1. About the Virtual Machines
Red Hat Enterprise Virtualization platform enables you to create virtual machines that perform the same functions as physical machines. Using a standard Web browser, users can run virtual machines that behave like physical desktops. Multiple levels of permissions allow users with different roles to manage virtual machines to meet the requirements of the enterprise.
Supported Guests
Red Hat Enterprise Virtualization presently supports the following virtualized guest operating systems:
Red Hat Enterprise Linux 3 (32 bit and 64 bit)
Red Hat Enterprise Linux 4 (32 bit and 64 bit)
Red Hat Enterprise Linux 5 (32 bit and 64 bit)
Red Hat Enterprise Linux 6 (32 bit and 64 bit)
Windows XP Service Pack 3 and newer (32 bit only)
Windows 7 (32 bit and 64 bit)
Windows Server 2003 Service Pack 2 and newer (32 bit and 64 bit)
Windows Server 2008 (32 bit and 64 bit)
Windows Server 2008 R2 (64 bit only)
1.1.2. About SPICE
The SPICE protocol allows the virtual machine to connect to the host with physical PC-like graphics performance. It supplies video at more than 30 frames per second, bi-directional audio (for softphones/IP phones), bi-directional video (for video telephony/video conferencing) and USB redirection from the client’s USB port into the virtual machine. SPICE also supports connection to multiple monitors with a single virtual machine. SPICE is automatically installed via ActiveX, using the browser on the virtual machine.
1.2. Installation Workflow
Red Hat Enterprise Virtualization requires installation and configuration of several components to create a functioning virtualization environment. You must install and configure each component in the order shown in the checklist that follows:
11
Red Hat Enterprise Virtualization 3.0 Installation Guide
Check System Requirements
Check hardware requirements, as seen in Section 2.1, “Hardware requirements”
.
Check software requirements, as seen in Section 2.2, “Software requirements”
.
Red Hat Enterprise Virtualization Manager Installation
Install Red Hat Enterprise Virtualization Manager, as seen in
Chapter 3, Manager Installation
.
Install Red Hat Enterprise Virtualization Manager Reports, as seen in Chapter 4, Data Collection
Setup and Reports Installation
Install Virtualization Hosts
Install Red Hat Enterprise Virtualization Hypervisor hosts, as seen in Chapter 7, Installing the Red
Hat Enterprise Virtualization Hypervisor
Install Red Hat Enterprise Linux Hosts, as seen in Chapter 8, Installing Red Hat Enterprise Linux
Plan Your Data Center
Plan your Red Hat Enterprise Virtualization Data Center(s), as seen in Chapter 9, Planning your Data
Setup Storage
12
Chapter 1. Overview
For an overview of the supported storage types, and how they are attached to the manager, see
Section 11.1, “Storage Domains Overview”
.
To populate your ISO storage domain with installation media, see Section 11.2, “Populate the ISO
Completion of the above steps will result in the creation of a functioning Red Hat Enterprise Virtualization environment capable of running virtual machines.
If at any stage of the installation you encounter an error, or unexpected behavior, during the installation process review
Appendix A, Troubleshooting and Error Messages
, and contact Red Hat Support.
13
Red Hat Enterprise Virtualization 3.0 Installation Guide
Chapter 2. System Requirements
This chapter outlines the hardware and software requirements for installing the Red Hat Enterprise
Virtualization platform. The requirements outlined herein are based on the minimum requirements for successful installation, configuration, and operation of a Red Hat Enterprise Virtualization environment.
Production Red Hat Enterprise Virtualization installations will have additional requirements in line with the relative workloads expected of them. The additional requirements for your specific implementation of the Red Hat Enterprise Virtualization product need to be determined by your solution architect. Guidance
Important — Listed Requirements are Mandatory
All listed requirements must be met before installation commences. Without the listed requirements installation of a fully functional Red Hat Enterprise Virtualization environment as described in this guide will not be possible.
Before commencing the installation you must consult the latest version of the Red Hat Enterprise
Virtualization — Manager Release Notes.
2.1. Hardware requirements
This section outlines the minimum hardware required to install, configure, and operate a Red Hat
Enterprise Virtualization environment. To setup a Red Hat Enterprise Virtualization environment it is necessary to have, at least: one machine to act as the management server, one or more machines to act as virtualization hosts - at least two are required to support migration and power management, one or more machines to use as clients for accessing the Administration Portal.
storage infrastructure provided by NFS, iSCSI, SAN, or local storage.
The hardware required for each of these systems is further outlined in the following sections. The Red
Hat Enterprise Virtualization environment also requires storage infrastructure that is accessible to the virtualization hosts. Storage infrastructure must be accessible using NFS, iSCSI, FC, or locally attached to virtualization hosts.
2.1.1. Management Server Requirements
The minimum and recommended hardware requirements outlined here are based on a typical small to medium sized installation. The exact requirements vary between deployments based on sizing and load.
Please use these recommendations as a guide only.
Minimum
A dual core CPU.
4 GB of available system RAM that is not being consumed by existing processes.
25 GB of locally accessible, writeable, disk space.
1 Network Interface Card (NIC) with bandwidth of at least 1 Gbps.
Recommended
14
Chapter 2. System Requirements
A quad core CPU or multiple dual core CPUs.
16 GB of system RAM.
50 GB of locally accessible, writeable, disk space.
1 Network Interface Card (NIC) with bandwidth of at least 1 Gbps.
The Red Hat Enterprise Virtualization Manager runs on Red Hat Enterprise Linux. To confirm whether or not specific hardware items are certified for use with Red Hat Enterprise Linux refer to http://www.redhat.com/rhel/compatibility/hardware/ .
2.1.2. Virtualization Host Requirements
Red Hat Enterprise Virtualization Hypervisors and Red Hat Enterprise Linux Hosts have a number of hardware requirements and supported limits.
2.1.2.1. CPU Requirements
Virtualization hosts must have at least one CPU. Red Hat Enterprise Virtualization supports the use of these CPU models in virtualization hosts:
AMD Opteron G1
AMD Opteron G2
AMD Opteron G3
Intel Conroe
Intel Penryn
Intel Nehalem
Intel Westmere
All CPUs must have support for the Intel® 64 or AMD64 CPU extensions, and the AMD-V™ or Intel VT® hardware virtualization extensions enabled. Support for the No eXecute flag (NX) is also required. To check that your processor supports the required virtualization extensions, and that they are enabled:
At the Red Hat Enterprise Linux or Red Hat Enterprise Virtualization Hypervisor boot screen press any key and select the Boot or Boot with serial console entry from the list. Press Tab to edit the kernel parameters for the selected option. After the last kernel parameter listed ensure there is a Space and append the rescue parameter.
Press Enter to boot into rescue mode.
At the prompt which appears, determine that your processor has the virtualization extensions and that they are enabled by running this command:
# grep -E 'svm|vmx' /proc/cpuinfo
If any output is shown, the processor is hardware virtualization capable. If no output is shown it is still possible that your processor supports hardware virtualization. In some circumstances manufacturers disable the virtualization extensions in the BIOS. Where you believe this to be the case consult the system's BIOS and the motherboard manual provided by the manufacturer.
As an additional check, verify that the kvm modules are loaded in the kernel:
# lsmod | grep kvm
If the output includes kvm_intel or kvm_amd then the kvm hardware virtualization modules are loaded and your system meets requirements.
15
Red Hat Enterprise Virtualization 3.0 Installation Guide
2.1.2.2. RAM Requirements
It is recommended that virtualization hosts have at least 2 GB of RAM. The amount of RAM required varies depending on: guest operating system requirements, guest application requirements, and memory activity and usage of guests.
The fact that KVM is able to over-commit physical RAM for virtualized guests must also be taken into account. This allows provisioning of guests with RAM requirements greater than physically present on the basis where not all guests will be at peak load concurrently. KVM does this by only allocating RAM for guests as required and shifting underutilized guests into swap.
A maximum of 1 TB of RAM per virtualization host is currently supported.
2.1.2.3. Storage Requirements
Virtualization hosts require local storage to store configuration, logs, kernel dumps, and for use as swap space. The minimum storage requirements of the Red Hat Enterprise Virtualization Hypervisor are documented in this section. The storage requirements for Red Hat Enterprise Linux hosts vary based on the amount of disk space used by their existing configuration but are expected to be greater than those of the Red Hat Enterprise Virtualization Hypervisor.
It is recommended that each virtualization host has at least 10 GB of internal storage. The minimum supported internal storage for each Hypervisor is the total of that required to provision the following partitions:
The root partitions require at least 512 MB of storage.
The configuration partition requires at least 8 MB of storage.
The recommended minimum size of the logging partition is 2048 MB.
The data partition requires at least 256 MB of storage. Use of a smaller data partition may prevent future upgrades of the Hypervisor from the Red Hat Enterprise Virtualization Manager. By default all disk space remaining after allocation of swap space will be allocated to the data partition.
The swap partition requires at least 8 MB of storage. The recommended size of the swap partition varies depending on both the system the Hypervisor is being installed upon and the anticipated level of overcommit for the environment. Overcommit allows the Red Hat Enterprise Virtualization environment to present more RAM to guests than is actually physically present. The default overcommit ratio is 0.5.
The recommended size of the swap partition can be determined by:
Multiplying the amount of system RAM by the expected overcommit ratio, and adding
2 GB of swap space for systems with 4 GB of RAM or less, or
4 GB of swap space for systems with between 4 GB and 16 GB of RAM, or
8 GB of swap space for systems with between 16 GB and 64 GB of RAM, or
16 GB of swap space for systems with between 64 GB and 256 GB of RAM.
Example 2.1. Calculating Swap Partition Size
For a system with 8 GB of RAM this means the formula for determining the amount of swap space to allocate is:
(8 GB x 0.5) + 4 GB = 8 GB
16
Chapter 2. System Requirements
Important — Fakeraid Devices are not Supported
The Red Hat Enterprise Virtualization Hypervisor does not support installation on fakeraid devices. Where a fakeraid device is present it must be reconfigured such that it no longer runs in RAID mode.
1. Access the RAID controller's BIOS and remove all logical drives from it.
2. Change controller mode to be non-RAID. This may be referred to as compatibility or JBOD mode.
Access the manufacturer provided documentation for further information related to the specific device in use.
2.1.2.4 . PCI Device Requirements
Virtualization hosts must have at least one network interface with a minimum bandwidth of 1 Gbps. It is recommended that each virtualization host have two network interfaces with a minimum bandwidth of 1
Gbps to support network intensive activity, including virtual machine migration.
2.2. Software requirements
2.2.1. Operating Systems
Red Hat Enterprise Virtualization Manager requires Red Hat Enterprise Linux 6.2 or higher. It is expected that you have successfully completed installation of the operating system prior to commencing installation of the Red Hat Enterprise Virtualization Manager.
Virtualization hosts must run Red Hat Enterprise Virtualization Hypervisor 6, Red Hat Enterprise
Linux 6.2, or a later edition of Red Hat Enterprise Linux. Where Red Hat Enterprise Linux hosts are to be used it is expected that you have completed installation of the operating system prior to commencing installation of the Red Hat Enterprise Virtualization Manager.
Installation of the Red Hat Enterprise Linux Hypervisor is, however, covered in this guide. More detailed information is available in the Red Hat Enterprise Linux - Hypervisor Deployment Guide.
2.2.2. Client Requirements
To access the Administration Portal, you need a client with a supported web browser. The
Administration Portal supports the following clients and browsers:
Client
Windows XP,
Windows 7 (x86, AMD64 and Intel 64), and
Windows 2008/R2 (x86, AMD64 and Intel 64).
Browser
Internet Explorer 7 and higher on Windows, with the .NET Framework 4 installed.
To access the User Portal, you need a thin client with a supported web browser. The User Portal supports the following clients and browsers:
Client
Red Hat Enterprise Linux 5.5 (i386, AMD64 and Intel 64)
Red Hat Enterprise Linux 6.0 (i386, AMD64 and Intel 64)
17
Red Hat Enterprise Virtualization 3.0 Installation Guide
Windows XP
Windows XP Embedded (XPe)
Windows 7 (x86, AMD64 and Intel 64)
Windows Embedded Standard 7
Windows 2008/R2 (x86, AMD64 and Intel 64)
Windows Embedded Standard 2009
Red Hat Enterprise Virtualization Certified Linux-based thin clients
Browser
Internet Explorer 7 and higher on Windows, with the SPICE ActiveX control installed
Mozilla Firefox 3.5 and higher on Red Hat Enterprise Linux, with the SPICE plugin installed
2.2.3. Red Hat Network (RHN)
2.2.3.1. Required Channels
Installation of the Red Hat Enterprise Virtualization Manager requires that the system be subscribed to a number of additional Red Hat Network channels. These channels are used to retrieve both the initial installation packages and later updates as they become available.
The Red Hat Enterprise Virtualization Manager (v.3 x86_64) channel, also referred to as rhel-x86_64-server-6-rhevm-3, provides Red Hat Enterprise Virtualization Manager.
The Channel Entitlement Name for this channel is Red Hat Enterprise Virtualization
Manager (v3).
The JBoss Application Platform (v 5) for 6Server x86_64 channel, also referred to as jbappplatform-5-x86_64-server-6-rpm, provides the supported release of the application platform on which the manager runs. The Channel Entitlement Name for this channel is
JBoss Enterprise Application Platform (v 4 , zip form at).
The RHEL Server Supplementary (v. 6 64-bit x86_64) channel, also referred to as
rhel-x86_64 -server-supplem entary-6, provides the supported version of the Java Runtime
Environment (JRE). The Channel Entitlement Name for this channel is Red Hat Enterprise
Linux Server Supplem entary (v. 6).
Use the rhn-channel --list command to confirm the list of channels to which the server is subscribed.
2.2.3.2. Red Hat Network Configuration
1. Register to Red Hat Network
Run the rhn_register command to register the system with the Red Hat Network. To complete registration successfully you will need to supply your Red Hat Network username and password.
Follow the onscreen prompts to complete registration of the system.
# rhn_register
2. Subscribe to Required Channels
You must subscribe the system to the required channels using either the Red Hat Network web interface or the command line rhn-channel command.
A. Using the Red Hat Network Web Interface
To add a channel subscription to a system from the web interface: a. Log on to Red Hat Network ( http://rhn.redhat.com
).
18
Chapter 2. System Requirements b. Click Systems at the top of the page.
c. Select the system to which you are adding channels from the list presented on the screen, by clicking the name of the system.
d. Click Alter Channel Subscriptions in the Subscribed Channels section of the screen.
e. Select the channel to be added from the list presented on the screen, then click the
Change Subscription button to finalize the change.
Repeat these steps for each additional channel the system is to be subscribed to.
B. Using the rhn-channel Command
Run the rhn-channel command to subscribe the system to each of the required channels.
The commands which need to be run are:
# rhn-channel --add --channel=rhel-x86_64-server-6-rhevm-3
# rhn-channel --add --channel=jbappplatform-5-x86_64-server-6-rpm
# rhn-channel --add --channel=rhel-x86_64-server-supplementary-6
Important — Troubleshooting rhn-channel Errors
If you are not the Red Hat Network administrator for the machine, or the machine is not registered to Red Hat Network, then use of the rhn-channel command will result in an error:
Error communicating with server. The message was:
Error Class Code: 37
Error Class Info: You are not allowed to perform administrative tasks on this system.
Explanation:
An error has occurred while processing your request. If this problem
persists please enter a bug report at bugzilla.redhat.com.
If you choose to submit the bug report, please be sure to include
details of what you were trying to do when this error occurred and
details on how to reproduce this problem.
If you encounter this error when using rhn-channel then to add the Red Hat Network channel to the system you must use the web user interface.
Result:
The system is now registered with Red Hat Network and subscribed to the channels required for Red
Hat Enterprise Virtualization Manager installation.
2.2.4. Directory Services
The term directory service refers to the collection of software, hardware, and processes that store information about an enterprise, subscribers, or both, and make that information available to users. A directory service consists of at least one instance of Directory Server and at least one directory client program. Client programs can access names, phone numbers, addresses, and other data stored in the directory service.
The Red Hat Enterprise Virtualization platform provides its own internal admin user. Authentication for other users is supported by attaching directory services domains using the provided domain
19
Red Hat Enterprise Virtualization 3.0 Installation Guide management tool, rhevm-manage-domains. Currently the two supported providers of directory services for use with the Red Hat Enterprise Virtualization Manager are Identity, Policy, and Audit (IPA) and Microsoft Active Directory.
For more information on configuring directory services see Appendix B, Directory Services
.
2.2.5. Firewall Configuration
This section documents the firewall requirements of the Red Hat Enterprise Virtualization environment.
The ports that need to be opened, the type of traffic the port is used for, and the source of traffic which will be received on the port will be covered for the:
Red Hat Enterprise Virtualization Manager, virtualization hosts, and directory server.
While specific configuration instructions for additional network infrastructure which may exist between these systems will not be covered it is intended that the information provided will assist with this task.
2.2.5.1. Red Hat Enterprise Virtualization Manager Firewall Requirements
The Red Hat Enterprise Virtualization Manager requires that a number of ports be opened to allow network traffic through the system's firewall. The rhevm-setup script is able to set the required firewall rules automatically. Where an existing firewall configuration exists this step is able to be skipped. This allows the required changes to be manually integrated with the existing firewall script(s).
The firewall configuration documented within this chapter assumes a default configuration. Where you choose alternative values during installation, such as specifying a different HTTP, or HTTPS, port adjust the firewall rules to allow the selected port - not the default listed here.
20
Chapter 2. System Requirements
Table 2.1. Red Hat Enterprise Virtualization Manager Firewall Requirements
Port(s)
22
Protocol
TCP
Source
System(s) used for maintenance of the manager including backend configuration, and software upgrades.
Destination
Red Hat
Enterprise
Virtualization
Manager
Purpose
SSH (optional)
8080, 8443 TCP
Administration
Portal clients
User Portal clients
Red Hat
Enterprise
Virtualization
Hypervisor(s)
Red Hat
Enterprise
Linux host(s)
REST API clients
Red Hat
Enterprise
Virtualization
Manager
Provides HTTP and HTTPS access to the manager.
Important — Additional Ports Required to Export Storage
Where the Red Hat Enterprise Virtualization Manager is also to export NFS storage, such as an
ISO Domain, then additional ports must be allowed through the firewall. The ports used for NFS, which need to be exposed to the Red Hat Enterprise Linux Hosts and Red Hat Enterprise
Virtualization Hypervisors, are listed in the /etc/sysconfig/nfs file:
$ cat /etc/sysconfig/nfs
LOCKD_TCPPORT=32803
LOCKD_UDPPORT=32769
MOUNTD_PORT=892
RQUOTAD_PORT=875
STATD_PORT=662
STATD_OUTGOING_PORT=2020
2.2.5.2. Virtualization Host Firewall Requirements
Both Red Hat Enterprise Linux hosts and Red Hat Enterprise Virtualization Hypervisors require that a number of ports be opened to allow network traffic through the system's firewall. In the case of the Red
Hat Enterprise Virtualization Hypervisor these firewall rules are configured automatically. For Red Hat
Enterprise Linux hosts however it is necessary to manually configure the firewall.
21
Red Hat Enterprise Virtualization 3.0 Installation Guide
Table 2.2. Virtualization Host Firewall Requirements
Port(s)
22
5634 - 6166
16514
49152 - 49216
54321
Protocol
TCP
TCP
TCP
TCP
TCP
Source
Red Hat
Enterprise
Virtualization
Manager
Administration
Portal clients
User Portal clients
Red Hat
Enterprise
Virtualization
Hypervisor(s)
Red Hat
Enterprise
Linux Host(s)
Red Hat
Enterprise
Linux
Hypervisor(s)
Red Hat
Enterprise
Linux Host(s)
Red Hat
Enterprise
Virtualization
Manager
Red Hat
Enterprise
Virtualization
Hypervisor(s)
Red Hat
Enterprise
Linux host(s)
Destination
Red Hat
Enterprise
Virtualization
Hypervisor(s)
Red Hat
Enterprise
Linux host(s)
Purpose
Secure Shell
(SSH) access.
Red Hat
Enterprise
Virtualization
Hypervisor(s)
Red Hat
Enterprise
Linux host(s)
Remote guest console access via VNC and
Spice. These ports must be open to facilitate client access to virtual machines.
Virtual machine migration using
libvirt.
Red Hat
Enterprise
Virtualization
Hypervisor(s)
Red Hat
Enterprise
Linux Host(s)
Red Hat
Enterprise
Linux
Hypervisor(s)
Red Hat
Enterprise
Linux Host(s)
Red Hat
Enterprise
Virtualization
Hypervisor(s)
Red Hat
Enterprise
Linux host(s)
Virtual machine migration and fencing using
VDSM. These ports must be open facilitate both automated and manually initiated migration of virtual machines.
VDSM communications with the Manager and other virtualization hosts.
22
Chapter 2. System Requirements
2.2.5.3. Directory Firewall Requirements
Red Hat Enterprise Virtualization requires a directory server to support user authentication. Currently the supported directory servers are IPA and Active Directory. Both require a number of ports to be opened in the directory server's firewall to support GSS-API authentication as used by the Red Hat
Enterprise Virtualization Manager.
Table 2.3. Host Firewall Requirements
Port(s)
88, 464
Protocol
TCP, UDP
Source
Red Hat
Enterprise
Virtualization
Manager
Destination
Directory server
Purpose
Kerberos authentication.
389, 636 TCP
Red Hat
Enterprise
Virtualization
Manager
Directory server
Lightweight
Directory Access
Protocol (LDAP) and LDAP over
SSL.
2.2.6. UIDs needed by RHEV
2.2.6.1. Required UIDs and GIDs
Red Hat Enterprise Virtualization requires certain User IDs and Group IDs (UIDs and GIDs) on the host system. When the vdsm and qemu packages are installed, default versions of these UIDs and GIDs are created on the host.
If existing UIDs and GIDs on the host conflict with the default values used during vdsm and qemu installation, a conflict occurs.
The UIDs and GIDs created by default during Red Hat Enterprise Virtualization installation are:
Table 2.4 . GIDs and UIDs required by RHEV
Name vdsm kvm qem u
UID
36 nil
107
GID
nil
36
107
Auxiliary Group
109 nil nil
23
24
Red Hat Enterprise Virtualization 3.0 Installation Guide
Part II. Installing Red Hat Enterprise Virtualization
Manager
Chapter 3. Manager Installation
Chapter 3. Manager Installation
Before proceeding with Red Hat Virtualization Manager installation you must ensure that all
prerequisites, as listed in Chapter 2, System Requirements
, are met. Once you have confirmed that all prerequisites are met you are ready to proceed with installation.
To perform initial installation and configuration of the Red Hat Enterprise Virtualization Manager follow
the steps in Section 3.1, “Installation”
. Once you have followed this procedure the Red Hat Enterprise
Virtualization Manager and dependencies, including JBoss ( http://www.jboss.com
), will be installed and configured ready for your first login. Further action must be undertaken to complete configuration of the environment to the point that you can create virtual machines. These tasks will be described in the following chapters.
To complete installation of the Red Hat Enterprise Virtualization Manager successfully you must be able to determine:
1. The ports to be used for HTTP, and HTTPS, communication. The defaults are 8080 and 8443 respectively.
2. The Fully Qualified Domain Name (FQDN) of the system the manager is to be installed on.
3. The password you will use to secure the Red Hat Enterprise Virtualization administration account.
4. The password you will use to secure the database.
5. The Organization Name to use when creating the manager's security certificates.
6. The storage type to be used for the initial data center attached to the manager. The default is
NFS.
7. The path to use for the ISO share, if the manager is being configured to provide one. The display name, which will be used to label the domain in the Red Hat Enterprise Virtualization Manager also needs to be provided.
8. The firewall rules, if any, present on the system that need to be integrated with the rules required for the manager to function.
Before installation is completed the values selected are displayed for confirmation. Once the values have been confirmed they are applied and the Red Hat Enterprise Virtualization Manager is ready for use.
Example 3.1. Completed Installation
RHEV Manager will be installed using the following configuration:
================================================================= http-port: 8080 https-port: 8443 host-fqdn: manager.demo.redhat.com
auth-pass: ******** db-pass: ******** org-name: Red Hat default-dc-type: NFS nfs-mp: /isodomain iso-domain-name: ISODomain override-iptables: yes
Proceed with the configuration listed above? (yes|no):
25
Red Hat Enterprise Virtualization 3.0 Installation Guide
Note — Automated Installation
Automated installations are created by providing rhevm-setup with an answer file. An answer file contains answers to the questions asked by the setup command.
To create an answer file, use the --gen-answer-file parameter to set the location to which the answer file must be saved. The rhevm-setup command will record your answers to the file.
# rhevm-setup --gen-answer-file=ANSWER_FILE
To use an answer file for a new installation, use the --answer-file parameter to set the location of the answer file that must be used. The command rhevm-setup command will use the answers stored in the file to complete installation.
# rhevm-setup --answer-file=ANSWER_FILE
Run rhevm-setup --help for further information.
3.1. Installation
The Red Hat Enterprise Virtualization Manager and all of its dependencies are available via Red Hat
Network. To install the manager you must ensure connectivity with either the Red Hat Network or a Red
Hat Network Satellite Server is available. You must also ensure that you have access to all required Red
Hat Network channels. See Section 2.2.3.1, “Required Channels”
for further information.
1. If installed, the classpathx-jaf package must be removed. It conflicts with some of the components installed to support JBoss.
# yum remove classpathx-jaf
2. Use yum to ensure that the most up to date versions of all installed packages are in use.
# yum upgrade
3. Use yum to initiate installation of the rhevm package and all dependencies. You must run this command as the root user.
# yum install rhevm
Result:
All required packages and dependencies are installed. You must now configure the system.
3.2. Configuration
Once package installation is complete the Red Hat Enterprise Virtualization Manager must be configured. The rhevm-setup command is provided to assist with this task. The script asks you a series of questions, the answers to which form the basis for system configuration. Once all required values have been provided the updated configuration is applied and the Red Hat Enterprise
Virtualization Manager services are started.
26
Chapter 3. Manager Installation
1. Start Setup Script
To begin configuring the system run rhevm-setup as the root user.
# rhevm-setup
2. Set Port for HTTP
The script prompts for entry of the port to use for HTTP communication. To use the default value,
8080, press Enter. To use an alternative value enter it in the field, and then press Enter.
HTTP Port [8080] :
The port you select also appears in the URL that must be used to access the Red Hat Enterprise
Virtualization Manager over HTTP.
Example 3.2. Access Using HTTP
For a machine with hostname manager.demo.redhat.com using the default HTTP port value, 8080, the URL to access the entry page over HTTP is
http://m anager.dem o.redhat.com :8080/.
3. Set Port for HTTPS
The script prompts for entry of the port to use for HTTPS communication. To use the default value, 8443, press Enter. To use an alternative value enter it in the field, and then press Enter.
HTTPS Port [8443] :
Where a port other than 8443 is selected it changes the URL that must be used to access the
Red Hat Enterprise Virtualization Manager over HTTPS.
Example 3.3. Access Using HTTPS
For a machine with hostname manager.demo.redhat.com using the default HTTPS port value, 8443, the URL to access the entry page over HTTPS is
https://m anager.dem o.redhat.com :84 4 3/.
4. Set Fully Qualified Domain Name (FQDN)
The script prompts for entry of the system's fully qualified domain name. This name should be resolvable via both forward and reverse DNS lookup. The script attempts to determine the fully qualified domain name automatically. The value identified is listed in square brackets as the default setting for the fully qualified domain name, based on your setup.
Host fully qualified domain name, note that this name should be fully resolvable [manager.demo.redhat.com] :
Where the automatically determined fully qualified domain name is correct, press Enter to use the value and continue. Where the automatically determined fully qualified domain name is not correct, enter the correct value and press Enter to use the new value and continue.
5. Set Administrator Password
The script creates an authentication domain internal to the Red Hat Enterprise Virtualization
Manager for the default administrative account. The domain is named internal, the administrative user is called admin. External authentication domains are added as a postinstallation step using the rhevm-manage-domains command.
You must choose a password for the admin user. You will be asked to enter it a second time to
27
28
Red Hat Enterprise Virtualization 3.0 Installation Guide confirm your selection.
Password for Administrator (admin@internal) :
6. Set Database Password
The script prompts for entry of a password to use for the Red Hat Enterprise Virtualization
Manager database. You must enter a strong password. Strong passwords consist of a mix of uppercase, lowercase, numeric, and punctuation characters. They are six or more characters long and do not contain dictionary words. Enter the desired password and press Enter. You will be asked to enter the password again to confirm it.
Database password (required for secure authentication with the locally created database) :
7. Set Organization Name
The script prompts for entry of the Organization Name. The Organization Name appears in the
Subject field of the certificate used to secure communications with the Red Hat Enterprise
Virtualization Manager.
Organization Name for the Certificate :
8. Configure Default Storage Type
The script prompts for selection of the default storage type. This is the storage type that is used for the Default data center. You are able to add further data centers that use different storage types from the Administration Portal at any time.
The default storage type you will be using ['NFS'| 'FC'| 'ISCSI'] [NFS] :
The default selection is Network File System (NFS). The other available values are:
Fibre Channel (FC),
Internet Small Computer System Interface (ISCSI), and
The NFS, FC, and ISCSI options are used to connect to remote storage. Red Hat Enterprise
Virtualization also supports The LOCALFS storage type which allows the use of local storage attached to the virtualization hosts, but this storage type is not supported for the Default data center.
To use the default selection, NFS, press Enter. To select FC, or ISCSI then enter the value and then press Enter.
9. Configure NFS ISO Domain
The script asks whether or not an NFS share should be configured on the server and used as an
ISO storage domain.
Should the installer configure NFS share on this server to be used as an ISO
Domain? ['yes'| 'no'] [yes] :
An ISO storage domain is used to store copies of removable media for use when provisioning and using virtual machines. The Red Hat Enterprise Virtualization Manager is able to use either an ISO storage domain on the system it is installed to or one that exists on remote storage. In either case the ISO storage domain must be accessible via NFS. The ability to configure an ISO storage domain is also available from the Administration Portal after installation.
To take the default action, which is to configure an NFS share for use as an ISO storage domain, press Enter. To skip this step type no and press Enter.
Chapter 3. Manager Installation
If you chose to configure an NFS share then you will also need to provide both a path and a display name for it. The path is the location on the local file system where the NFS share must be created. The directory must not already exist.
Mount point path:
The display name is the name the storage domain will appear under in the Red Hat Enterprise
Virtualization Manager. The display name must not contain non-alphanumeric characters other than the underscore (_) and the hyphen (-).
Display name for the ISO domain:
The ISO domain will be created and exported as an NFS share. It will be shown as active in the
Red Hat Enterprise Virtualization Manager once the first active virtualization host has been added to the Default data center.
10. Configure Firewall
The Red Hat Enterprise Virtualization Manager requires that network traffic on a number of ports be allowed through the system's firewall. The rhevm-setup script is able to configure this automatically, but selecting this option overrides any existing firewall configuration. Where there is an existing firewall configuration that needs to be maintained you must manually configure the firewall to include the additional rules required by the Red Hat Enterprise Virtualization Manager.
Firewall ports need to be opened.
You can let the installer configure iptables automatically overriding the current configuration. The old configuration will be backed up.
Alternately you can configure the firewall later using an example iptables file found under /usr/share/rhevm/conf/iptables.example
Should the installer configure iptables now? ['yes'| 'no'] [yes] :
A. To proceed with automatic firewall configuration type yes and then press Enter.
B. To skip automatic firewall configuration type no and then press Enter. You will need to add rules equivalent to those found in /usr/share/rhevm/conf/iptables.example to your
iptables configuration.
11. Confirm Configuration
You have now provided the script with all the information required to complete configuration of the
Red Hat Enterprise Virtualization Manager. The values which you entered are displayed for confirmation.
Example 3.4 . Configuration Confirmation Screen
RHEV Manager will be installed using the following configuration:
================================================================= http-port: 8080 https-port: 8443 host-fqdn: manager.demo.redhat.com
auth-pass: ******** db-pass: ******** org-name: Red Hat default-dc-type: NFS nfs-mp: /isoshare iso-domain-name: ISODomain override-iptables: yes
Proceed with the configuration listed above? (yes|no):
29
Red Hat Enterprise Virtualization 3.0 Installation Guide
A. To permanently apply the configuration values listed type yes and then press Enter to apply the configuration.
B. If one or more of the configuration values listed is incorrect type no and then Enter to revisit the configuration.
The configuration values are applied. A number of services need to be started and as a result this step takes some time. Do not terminate the installation once application of the configuration values has commenced.
Once the script has completed successfully take note of the additional information it provides. In particular note down the SSH Certificate fingerprint, SSH Public key
fingerprint, and Red Hat Enterprise Virtualization Manager URL for your records.
Example 3.5. Successful Configuration
Installing:
Creating JBoss Profile... [ DONE ]
Creating CA... [ DONE ]
Setting Database Security... [ DONE ]
Creating Database... [ DONE ]
Updating the Default Data Center Storage Type... [ DONE ]
Editing JBoss Configuration... [ DONE ]
Editing RHEV Manager Configuration... [ DONE ]
Configuring the Default ISO Domain... [ DONE ]
Configuring Firewall (iptables)... [ DONE ]
Starting JBoss Service... [ DONE ]
**** Installation completed successfully ******
(Please allow RHEV Manager a few moments to start up.....)
Additional information:
* SSL Certificate fingerprint:
4C:A4:8F:93:62:50:C1:63:C8:09:70:77:07:90:FD:65:5B:3C:E8:DD
* SSH Public key fingerprint: fa:71:38:88:58:67:ae:f0:b1:17:fe:91:31:6c:66:6e
* A default ISO share has been created on this host.
If IP based access restrictions are required, please edit /isoshare entry in /etc/exports
* The firewall has been updated, the old iptables configuration file was saved to /usr/share/rhevm/conf/iptables.backup.103654-09092011_866
* The installation log file is available at: /var/log/rhevm/rhevmsetup_2011_09_09_10_32_56.log
* Please use the user "admin" and password specified in order to login into RHEV Manager
* To configure additional users, first configure authentication domains using the 'rhevm-manage-domains' utility
* To access RHEV Manager please go to the following URL: http://manager.demo.redhat.com:8080
Result:
The Red Hat Enterprise Virtualization Manager has been installed and configured successfully. You are
Administration Portal” for further information.
30
Chapter 3. Manager Installation
Note — Periodic Updates
Red Hat periodically provides updates to the Red Hat Enterprise Virtualization Manager. For
information on upgrading to newer releases, refer to Chapter 5, Upgrades between Minor
3.3. Removing Red Hat Enterprise Virtualization Manager
The Red Hat Enterprise Virtualization Manager provides the rhevm-cleanup utility to allow quick and easy removal of the data files associated with the installation. Once this has been run you are able to remove the Red Hat Enterprise Virtualization Manager packages using yum.
Warning — Potential Data Loss
The rhevm-cleanup command removes all existing Red Hat Enterprise Virtualization Manager data. This includes configuration settings, certificates, and database tables.
1. Run the rhevm-cleanup command on the system that Red Hat Enterprise Virtualization
Manager is installed on. You must be logged in as the root user to run rhevm-cleanup.
2. The script prompts you to confirm that you wish to remove Red Hat Enterprise Virtualization
Manager.
Would you like to proceed? (yes|no): yes
Type yes and then press Enter to proceed with removal of Red Hat Enterprise Virtualization
Manager.
3. The rhevm-cleanup command displays a message confirming that the Red Hat Enterprise
Virtualization data files have been removed successfully.
RHEV Manager cleanup finished successfully!
To complete removal of the Red Hat Enterprise Virtualization Manager you must also use yum to remove the relevant packages. While still logged in as the root user run:
# yum remove rhevm* vdsm-bootstrap
Result:
Red Hat Enterprise Virtualization Manager has been removed from the system successfully.
3.4. Connect to the Administration Portal
The Administration Portal allows you to create, configure, monitor, and maintain the Red Hat Enterprise
Virtualization environment using a graphical interface. To begin configuring your Red Hat Enterprise
Virtualization environment you must first log into the Administration Portal. Before logging in the first time there are a number of prerequisites that must be met.
The system(s) used to access the Administration Portal must run either:
31
Red Hat Enterprise Virtualization 3.0 Installation Guide
Windows XP,
Windows 7, or
Windows Server 2008 R2.
Additionally, the system must have Internet Explorer 7 or later, and the .NET Framework 4 installed.
Further checks must also be performed to ensure that Internet Explorer's security configuration supports the Administration Portal. To access the Administration Portal successfully you must make the following changes to the security configuration: disable Internet Explorer Enhanced Security Configuration (Windows Server 2008 R2 only), add the Red Hat Enterprise Virtualization Manager to your list of Trusted Sites, and enable support for XAML browser applications.
This section includes information on all of the steps that you need to undertake to ensure that these requirements are met. If you have already met all of the listed requirements you can proceed directly to
Install .NET Framework 4
The installation package for the .NET Framework 4 is available at http://www.microsoft.com/download/en/details.aspx?id=17718 . You should download, and run this executable prior to accessing the Administration Portal for the first time. You will need to run the executable as a user with administration access to the system.
Configure Internet Explorer Enhanced Security Configuration
Internet Explorer on Windows Server 2008 R2 includes an Enhanced Security Configuration. To access the Administration Portal from these platforms you must first disable the Enhanced Security
Configuration.
1. Click Start → Administrative Tools → Server Manager. On the Security Information pane in the Server Manager window, click Configure IE ESC.
2. The Internet Explorer Enhanced Security Configuration dialog displays. Select
Off for Administrators and Users to disable the security configuration. Click OK.
32
Chapter 3. Manager Installation
Figure 3.1. Disable Internet Explorer Enhanced Security Configuration
Certificate Installation and Browser Configuration
To access the Administration Portal from any system, regardless of the version of Windows or Internet
Explorer in use, you must: install the certification authority's certificate as a trusted root certification authority, and install the Red Hat Enterprise Virtualization site certificate.
These changes must be made to support secure access to the Administration Portal.
1. Open a browser and navigate to http://manager.demo.redhat.com:8080/RHEVManager.
Substitute manager.demo.redhat.com with the fully qualified domain name provided during
Red Hat Enterprise Virtualization Manager installation. Additionally, where a non-default HTTP port was selected during installation replace 8080 with the port that was chosen.
2. To trust the certification authority's certificate click the this certificate link. When prompted select to Open the file. On Internet Explorer 9 the prompt appears at the bottom of the screen.
Earlier versions will display a dialog box instead.
3. On the screen that appears, click Install Certificate to commence certificate installation.
4. On the Certificate Store screen enable the Place all certificates in the
following store option, then click the Browse... button.
5. From the list of certificate stores, select Trusted Root Certification Authorities and click OK.
6. Click Next >, then follow the prompts to complete installation of the certification authority's
33
Red Hat Enterprise Virtualization 3.0 Installation Guide certificate.
7. Click the here link on the Red Hat Enterprise Virtualization Manager page to download and launch the site certificate installation. Follow the prompts to complete installation of the certificate.
Result:
The certification authority and site certificates have successfully been installed. Users of Internet
Explorer 9 must complete additional configuration before accessing the Administration Portal.
Additional Configuration for Internet Explorer 9
To access the Administration Portal using Internet Explorer 9 you must add the Red Hat Enterprise
Virtualization Manager's fully qualified domain name as a Trusted Site in Internet Explorer. Additionally you must ensure that support for XAML browser applications is enabled.
1. On the browser's toolbar, click Tools → Internet Options. The Internet Options dialog displays. Click on the Security tab and select Trusted Sites.
Figure 3.2. Add to Trusted Sites
34
2. Click Sites to display the Trusted Sites dialog. The URL for your Administration Portal should appear in the text box under Add this website to the zone. Click Add to move the site to the list of trusted zones, then click Close.
3. Click Custom Level.... Locate the XAML browser applications item in the list, ensure
Chapter 3. Manager Installation that it is set to Enable, then click Ok.
4. Click Ok to save the configuration changes, you must now restart Internet Explorer for them to take effect.
Result:
The Red Hat Enterprise Virtualization Manager is listed in trusted sites, and Internet Explorer is configured to allow the running of XAML browser applications in this zone.
Connecting
Now that the prerequisites have been resolved, you can log in to the Red Hat Enterprise Virtualization
Manager. Ensure that you have the user name and password provided during Red Hat Enterprise
Virtualization Manager installation.
Procedure 3.1. Connect to Red Hat Enterprise Virtualization web management portal
1. Return to the browser and navigate to
https://manager.demo.redhat.com:84 4 3/RHEVManager. Substitute
m anager.dem o.redhat.com with the URL provided during installation. Additionally where a non-default HTTPS port was selected during installation, replace 8443 in the URL with the port that was chosen.
2. If this is your first time connecting to the Administration Portal, you will be prompted to trust the
ca.cer certificate and install the RHEV-GUI-CertificateInstaller.exe certificate.
Figure 3.3. Install certificate
Follow the prompts, then click the new link that appears on the page to reload the Administration
Portal.
3. The portal login screen displays. Enter admin as your User Name. Enter the password that was set during installation in the Password field. Select the internal domain from the Domain list.
Click Login to log in.
35
Red Hat Enterprise Virtualization 3.0 Installation Guide
Figure 3.4 . Administration Portal Login Page
Result:
You have now successfully logged into the Red Hat Enterprise Virtualization web Administration Portal.
You can now:
Setup and Reports Installation
begin installing virtualization hosts - see Part III, “Installing Virtualization Hosts”
.
36
Chapter 4. Data Collection Setup and Reports Installation
Chapter 4. Data Collection Setup and Reports Installation
The Red Hat Enterprise Virtualization Manager optionally includes a comprehensive management history database, which can be utilized by any application to extract a range of information at the data center, cluster, and host levels. As the database structure changes over time a number of database views are also included to provide a consistent structure to consuming applications. A view is a virtual table composed of the result set of a database query. The definition of a view is stored in the database as a SELECT statement. The result set of the SELECT statement populates the virtual table returned by the view. If the optional comprehensive management history database has been enabled, the history tables and their associated views are stored in the rhevm_history database.
In addition to the history database Red Hat Enterprise Virtualization Manager Reports functionality is also available as an optional component. Red Hat Enterprise Virtualization Manager Reports provides a customized implementation of JasperServer, and JasperReports. JasperServer is a component of
JasperReports, an open source reporting tool, capable of being embedded in Java-based applications. It produces reports which can be rendered to screen, printed, or exported to a variety of formats including
PDF, Excel, CSV, Word, RTF, Flash, ODT and ODS. Reports built in Red Hat Enterprise Virtualization
Manager Reports are accessed via a web interface. In addition to a range of pre-configured reports and dashboards for monitoring the system, you are also able to create your own ad hoc reports.
Before proceeding with Red Hat Virtualization Manager Reports installation you must first have installed the Red Hat Enterprise Virtualization Manager, as described in
Chapter 3, Manager Installation
.
37
Red Hat Enterprise Virtualization 3.0 Installation Guide
The Red Hat Enterprise Virtualization Manager Reports functionality depends on the presence of the history database, which is installed separately. Both the history database and the Red Hat Enterprise
Virtualization Manager Reports are optional components. They are not installed by default when you install the Red Hat Enterprise Virtualization Manager.
To install and configure the rhevm_history database, see Procedure 4.1, “Install and Configure
To install and configure the Red Hat Enterprise Virtualization Manager Reports, see Procedure 4.2,
“Install and Configure Red Hat Enterprise Virtualization Manager Reports” . You must ensure that you
have installed, and configured, the rhevm_history database prior to installing JasperReports.
Procedure 4 .1. Install and Configure History Database
1. Install Required Packages
Use yum to initiate installation of the rhevm-reports-dwh package, or the rhevm-reports package if you also intend to install Red Hat Enterprise Virtualization Manager Reports. You must run this command as the root user on the system hosting the Red Hat Enterprise Virtualization Manager.
A. To install only the data warehouse package:
# yum install rhevm-reports-dwh
B. To install both the data warehouse package and the Red Hat Enterprise Virtualization
Manager Reports package:
# yum install rhevm-reports
2. Confirm Package Installation
The required packages are downloaded. Once all packages have been downloaded they are listed for review. You will be prompted to confirm that you wish to continue with the installation.
Once you have confirmed the operation yum installs the packages. Some further configuration is, however, required before the reports functionality can be used.
3. Configure History Database
You need to use the rhevm-dwh-setup command to configure the Extract, Transform, Load
(ETL) process and database scripts used to create and maintain a working history database.
a. You must run this command as the root user on the system hosting the Red Hat
Enterprise Virtualization Manager.
# rhevm-dwh-setup b. For the history database installation to take effect it is necessary to restart the jbossas service. The rhevm-dwh-setup command asks you:
Would you like to stop the JBoss service? (yes|no):
Type yes and then press Enter to proceed. The command then: stops the jbossas service, creates and configures the rhevm_history database, and starts the jbossas service.
Result:
The rhevm_history database has been created. The Red Hat Enterprise Virtualization Manager is
38
Chapter 4. Data Collection Setup and Reports Installation configured to log information to this database for reporting purposes.
Procedure 4 .2. Install and Configure Red Hat Enterprise Virtualization Manager Reports
1. Use yum to install the Red Hat Enterprise Virtualization Manager Reports package, rhevm-reports, if you did not already do this when performing the datawarehouse installation. This package must be installed on the system that the Red Hat Enterprise Virtualization Manager is installed. You must be logged in as the root user.
# yum install rhevm-reports
2. You must run this command as the root user on the system hosting the Red Hat Enterprise
Virtualization Manager.
# rhevm-reports-setup
3. For the Red Hat Enterprise Virtualization Manager Reports installation to take effect it is necessary to restart the jbossas service. The rhevm-reports-setup command asks you:
In order to proceed the installer must stop the JBoss service
Would you like to stop the JBoss service? (yes|no):
Type yes and then press Enter to proceed. The command then performs a number of actions before prompting you to set the password for the Red Hat Enterprise Virtualization Manager
Reports administrative user (rhev-admin). Note that the reports system maintains its own set of credentials.
Please choose a password for the admin user (rhevm-admin):
You will be prompted to enter the password a second time to confirm it.
Result:
Red Hat Enterprise Virtualization Manager Reports have been installed successfully. Access Red Hat
Enterprise Virtualization Manager Reports at http://demo.redhat.com:8080/rhevm-reports, replacing demo.redhat.com with the fully qualified domain name of the Red Hat Enterprise Virtualization
Manager. If during Red Hat Enterprise Virtualization Manager installation you selected a non-default
HTTP port replace 8080 with the port chosen.
Use the username rhevm-admin and the password you set during reports installation to log in for the first time. Note that the first time you log into Red Hat Enterprise Virtualization Manager Reports a number of web pages are generated, as a result your initial attempt to login may take some time to complete.
39
Red Hat Enterprise Virtualization 3.0 Installation Guide
Chapter 5. Upgrades between Minor Releases
Upgrades of the Red Hat Enterprise Virtualization Manager are released via Red Hat Network. Before installing an update from the Red Hat Network be sure to read the advisory text associated with it as well as the most recent version of the Red Hat Enterprise Virtualization — Release Notes, and the Red
Hat Enterprise Virtualization — Technical Notes.
To complete an upgrade a number of actions must be performed including: stopping the JBoss service, downloading and installing the updated packages, backing up and updating the database, performing post installation configuration, and restarting the JBoss service.
A script is included to perform all of these actions for you in an automated fashion. Active virtualization hosts are not upgraded by this process and must be updated separately. As a result the virtual machines running upon them are not affected.
Upgrading the Red Hat Enterprise Virtualization Manager requires network connectivity with either Red
Hat Network or a Red Hat Network Satellite Server installation. You must be logged in as the root user to initiate the upgrade process.
Before you upgrade your Red Hat Enterprise Virtualization Manager installation ensure you have the latest version of the installation utilities by running yum update rhevm-setup as the root user.
Once this has been done to commence an upgrade of the Red Hat Enterprise Virtualization Manager run the rhevm-upgrade command, again as the root user. No additional parameters are required. The command will produce output when it has completed each step of the upgrade process.
Be aware that the upgrade process may take some time. Allow time for the upgrade process to complete and do not stop it once initiated. Once the upgrade has been completed you will also be instructed to separately upgrade the data warehouse and reports functionality. These additional steps are only required if these optional packages are installed.
Note — Upgrading Red Hat Enterprise Virtualization Hypervisors
Red Hat Enterprise Virtualization Hypervisors can be updated directly or via the Red Hat
Enterprise Virtualization Manager. For information on upgrading the hypervisor see the Red Hat
Enterprise Linux — Hypervisor Deployment Guide.
4 0
Chapter 5. Upgrades between Minor Releases
Example 5.1. Upgrade Output
# rhevm-upgrade
Checking for updates....
Stopping JBoss Service... DONE!
Backing Up RHEVM DB... DONE!
Updating RHEVM rpm... DONE!
Updating RHEVM DB... DONE!
Running post install configuration... DONE!
Starting JBoss... DONE!
Upgrade log available at /var/log/rhevm/rhevm-upgrade_2011_07_27_08_15_10.log
DB Backup available at /usr/share/rhevm/db-backups/tmpVCI0WM.sql
To upgrade the history service or the reporting package, please run yum update rhevm-reports* and then rhevm-dwh-setup and rhevm-reports-setup.
4 1
4 2
Red Hat Enterprise Virtualization 3.0 Installation Guide
Part III. Installing Virtualization Hosts
Chapter 6. Introduction to Virtualization Hosts
Chapter 6. Introduction to Virtualization Hosts
Red Hat Enterprise Virtualization supports both virtualization hosts which run the Red Hat Enterprise
Virtualization Hypervisor, and those which run Red Hat Enterprise Linux. Both types of virtualization host are able to coexist in the same Red Hat Enterprise Virtualization environment.
Prior to installing virtualization hosts you should ensure that:
you have successfully completed installation of the Red Hat Enterprise Virtualization Manager as
outlined in Chapter 3, Manager Installation
.
Additionally you may have chosen to install the Red Hat Enterprise Virtualization Manager Reports. This is not mandatory and is not required to commence installing virtualization hosts. Once you have completed the above tasks you are ready to install virtualization hosts.
To install Red Hat Enterprise Virtualization Hypervisors, see Chapter 7, Installing the Red Hat
Enterprise Virtualization Hypervisor
To install Red Hat Enterprise Linux Hosts, see Chapter 8, Installing Red Hat Enterprise Linux Hosts
.
Important — Attach at Least Two Virtualization Hosts
It is recommended that you install at least two virtualization hosts and attach them to the Red Hat
Enterprise Virtualization environment. Where you attach only one virtualization host you will be unable to access features such as migration which require redundant hosts..
4 3
Red Hat Enterprise Virtualization 3.0 Installation Guide
Chapter 7. Installing the Red Hat Enterprise Virtualization
Hypervisor
This chapter covers installing and integrating Red Hat Enterprise Virtualization Hypervisors with a Red
Hat Enterprise Virtualization Manager.
The Red Hat Enterprise Virtualization Hypervisor must be installed on a physical server and cannot be installed on a virtual machine.
The installation process will reconfigure the selected storage device and destroy all data. Therefore, ensure that any data to be retained is successfully backed up before proceeding.
The following method can be used when installing multiple servers. However, ensure that unique hostnames and IP addresses are used for each hypervisor installation, in order to avoid network conflicts.
The following procedure provides installation instructions for using a CD-ROM created using the Red
Hat Enterprise Virtualization Hypervisor ISO image available from Red Hat. For alternative installation methods using USB Flash Drive or Network (PXE) Boot, refer to the Red Hat Enterprise Linux —
Hypervisor Deployment Guide available at http://www.redhat.com/docs/ .
Red Hat Enterprise Virtualization Hypervisors can use Storage Attached Networks (SANs) and other network storage for storing virtualized guest images. However, a local storage device is required for installing and booting the hypervisor.
Important — DNS Configuration
The Red Hat Enterprise Virtualization Hypervisor must exist in the same DNS domain as the Red
Hat Enterprise Virtualization Manager.
Important — UEFI Systems
Installation on systems with UEFI boot enabled is not currently supported. While installation will complete successfully with UEFI enabled the system must be configured to use legacy boot mode before the Hypervisor will start successfully.
Note — Automated Installations
Red Hat Enterprise Virtualization Hypervisor installations can be automated or conducted without interaction. This type of installation is only recommended for advanced users. Refer to the Red
Hat Enterprise Virtualization — Hypervisor Deployment Guide for more information.
7.1. Installation Media
This section covers creating installation media and preparing your systems before installing a Red Hat
Enterprise Virtualization Hypervisor.
This section covers installing Red Hat Enterprise Virtualization Hypervisors on a local storage device.
This storage device is a removable USB storage device, an internal hard disk drive or solid state drive.
Once the hypervisor is installed, the system will boot the hypervisor and all configuration data is preserved on the system.
4 4
Chapter 7. Installing the Red Hat Enterprise Virtualization Hypervisor
7.1.1. Preparation Instructions
The rhev-hypervisor* packages are needed to support Hypervisor installation. The packages contain the
Hypervisor CD-ROM images.
Releases of the Hypervisor are distributed using the Red Hat Enterprise Virtualization
Hypervisor (v.6 x86_64 ) channel, also referred to by the identifier rhel-x86_64 -server-6-
rhevh in Red Hat Network.
Downloading and Installing the RPM Package
The Red Hat Enterprise Virtualization Hypervisor channel contains additional tools for USB and PXE installations in the rhev-hypervisor-tools package, this package will also be installed when you follow this procedure.
Note
Red Hat Enterprise Linux 6.2 and later allows more than one version of the hypervisor ISO image to be installed at one time. As such, rhev-hypervisor.iso is now a symbolic link to a uniquely-named version of the hypervisor ISO image, such as /usr/share/rhev-
hypervisor/rhevh-6.2-20111006.0.el6.iso. Different versions of the hypervisor ISO can be installed alongside each other, allowing administrators to run and maintain a cluster on a previous version of the hypervisor while upgrading another cluster for testing.
Additionally, the symbolic links /usr/share/rhev-hypervisor/rhev-hypervisor5.iso and /usr/share/rhev-hypervisor/rhev-hypervisor6.iso are also created as needed.
They link to the most recent installed version of the ISO for Red Hat Enterprise Virtualization
Hypervisor 5 and Red Hat Enterprise Virtualization Hypervisor 6 respectively.
1. Log on to Red Hat Network ( http://rhn.redhat.com
).
2. Click Systems at the top of the page.
3. Select the system to which you are adding channels from the list presented on the screen, by clicking the name of the system.
4. Click Alter Channel Subscriptions in the Subscribed Channels section of the screen.
5. Select the Red Hat Enterprise Virtualization Hypervisor (v.6 x86_64) channel from the list presented on the screen, then click the Change Subscription button to finalize the change.
6. Log in to the system on which the Red Hat Enterprise Virtualization Manager is installed. You must log in as the root user.
7. Use yum to install the rhev-hypervisor and rhev-hypervisor-tools packages.
# yum install "rhev-hypervisor*"
Result:
The hypervisor ISO image is installed into the /usr/share/rhev-hypervisor/ directory. The symbolic link /usr/share/rhev-hypervisor/rhev-hypervisor.iso is updated to point to the
ISO image.
The rhevh-iso-to-disk and rhevh-iso-to-pxeboot scripts are installed to the /usr/bin directory.
4 5
Red Hat Enterprise Virtualization 3.0 Installation Guide
BIOS Settings and Boot Process Troubleshooting
Before installing Red Hat Enterprise Virtualization Hypervisors it is necessary to verify the BIOS is correctly configured for the chosen installation method. Many motherboard and PC manufacturers disable different booting methods in the BIOS. Most BIOS chips boot from the following devices in order:
1. 3.5 inch diskette
2. CD-ROM or DVD device
3. Local hard disk
Many BIOS chips have disabled one or more of the following boot methods: USB storage devices, CD-
ROMs, DVDs or network boot. To boot from your chosen method, enable the method or device and set that device as the first boot device in BIOS.
Most but not all motherboards support the boot methods described in this chapter. Consult the documentation for your motherboard or system to determine whether it is possible to use a particular boot method.
Warning — BIOS Settings Vary Between Manufacturers
BIOS settings vary between manufacturers. Any specific examples of BIOS settings may be inaccurate for some systems. Due to this inconsistency, it is necessary to review the motherboard or system manufacturer's documentation.
Confirm Hardware Virtualization Support
Verify that your system is capable of running the Red Hat Enterprise Virtualization Hypervisor.
Hypervisors require that virtualization extensions are present and enabled in the BIOS before installation proceeds.
1. Boot the hypervisor from removable media. For example, a USB stick or CD-ROM.
2. When the message Automatic boot in 30 seconds... is displayed, and begins counting down from thirty, press any key to skip the automatic boot process.
3. Ensure the Install or Upgrade option is selected and press Tab to edit the boot parameters.
4. Add the rescue parameter to the list of boot parameters shown on the screen, then press
Enter. This action will boot the hypervisor in rescue mode.
5. Once the hypervisor boots, verify your CPU contains the virtualization extensions with the following command:
# grep -E 'svm|vmx' /proc/cpuinfo
Output displays if the processor has the hardware virtualization extensions.
6. Verify that the KVM modules load by default:
# lsmod | grep kvm
Result:
If the output includes kvm_intel or kvm_amd then the kvm hardware virtualization modules are loaded and the system meets the requirements. If the output does not include the required modules then you must check that your hardware supports the virtualization extensions and that they are enabled in the
4 6
Chapter 7. Installing the Red Hat Enterprise Virtualization Hypervisor must check that your hardware supports the virtualization extensions and that they are enabled in the system's BIOS.
7.1.2. Preparing a Hypervisor USB Storage Device
The hypervisor is able to install itself onto USB storage devices or solid state disks. However, the initial boot/install USB device must be a separate device from the installation target. Network booting with PXE and tftp provides the greatest flexibility and scalability. For environments where network restrictions prevent network booting, or for systems without PXE capable network interface cards, a local media installation such as CD-ROM or USB is necessary. Booting from USB storage devices is a useful alternative to booting from CD, for systems without CD-ROM drives.
Note — USB Boot Support
Not all systems support booting from a USB storage device. Ensure that your system's BIOS supports booting from USB storage devices before proceeding.
7.1.2.1. Making a USB Storage Device into a Hypervisor Boot Device
This section covers making USB storage devices which are able to be used to boot hypervisors.
7.1.2.1.1. Using rhevh-iso-to-disk to Create USB Install Media
The rhevh-iso-to-disk command will install a hypervisor onto a USB storage device. The rhevh-
iso-to-disk command is part of the rhev-hypervisor package. Devices created with this command are able to boot the hypervisors on systems which support booting via USB.
The basic rhevh-iso-to-disk command usage follows this structure:
# rhevh-iso-to-disk image device
Where the device parameter is the partition name of the USB storage device to install to. The image parameter is a ISO image of the hypervisor. The default hypervisor image location is
/usr/share/rhev-hypervisor/rhev-hypervisor.iso. The rhevh-iso-to-disk command requires devices to be formatted with the FAT or EXT3 file system.
Note — Partitions and rhevh-iso-to-disk
rhevh-iso-to-disk uses a FAT or EXT 3 formatted partition or block device.
USB storage devices are sometimes formatted without a partition table, use /dev/sdb or similar device name.
When a USB storage device is formatted with a partition table, use /dev/sdb1 or similar device name.
1. Install the rhev-hypervisor package. Refer to Downloading and Installing the RPM Package
2. Use the rhevh-iso-to-disk command to copy the .iso file to the disk. The --format parameter formats the disk. The --reset-mbr initializes the Master Boot Record (MBR). The example uses a USB storage device named /dev/sdc.
4 7
Red Hat Enterprise Virtualization 3.0 Installation Guide
Example 7.1. Use of rhevh-iso-to-disk
# rhevh-iso-to-disk --format --reset-mbr /usr/share/rhev-hypervisor/rhevhypervisor.iso /dev/sdc
Verifying image...
/usr/share/rhev-hypervisor/rhev-hypervisor.iso: eccc12a0530b9f22e5ba62b848922309
Fragment sums:
8688f5473e9c176a73f7a37499358557e6c397c9ce2dafb5eca5498fb586
Fragment count: 20
Checking: 100.0%
The media check is complete, the result is: PASS.
It is OK to use this media.
Copying live image to USB stick
Updating boot config file
Installing boot loader syslinux: only 512-byte sectors are supported
USB stick set up as live image!
Result:
The USB storage device (/dev/sdc) is ready to be used to boot a system and install the hypervisor on it.
7.1.2.1.2. Using dd to Create USB Install Media
The dd command can also be used to install a hypervisor onto a USB storage device. Media created with the command can boot the hypervisor on systems which support booting via USB. Red Hat
Enterprise Linux provides dd as part of the coreutils package. Versions of dd are also available on a wide variety of Linux and Unix operating systems.
Windows users are able to obtain the dd command through installation of Red Hat Cygwin, a free
Linux-like environment for Windows. Refer to Procedure 7.2, “Using dd to Create USB Install Media on
hypervisor to a USB storage device.
The basic dd command usage follows this structure:
# dd if=image of=device
Where the device parameter is the device name of the USB storage device to install to. The image parameter is a ISO image of the hypervisor. The default hypervisor image location is
/usr/share/rhev-hypervisor/rhev-hypervisor.iso. The dd command does not make assumptions as to the format of the device as it performs a low-level copy of the raw data in the selected image.
Procedure 7.1. Using dd to Create USB Install Media
1. Install the rhev-hypervisor package. Refer to Downloading and Installing the RPM Package
2. Use the dd command to copy the .iso file to the disk. The example uses a USB storage device named /dev/sdc.
4 8
Chapter 7. Installing the Red Hat Enterprise Virtualization Hypervisor
Example 7.2. Use of dd
# dd if=/usr/share/rhev-hypervisor/rhev-hypervisor.iso of=/dev/sdc
243712+0 records in
243712+0 records out
124780544 bytes (125 MB) copied, 56.3009 s, 2.2 MB/s
Warning — All Data on the Device Specified Will be Overwritten
The dd command will overwrite all data on the device specified for the of parameter. Any existing data on the device will be destroyed. Ensure that the correct device is specified and that it contains no valuable data before invocation of the dd command.
Result:
The USB storage device (/dev/sdc) is ready to boot a hypervisor.
Procedure 7.2. Using dd to Create USB Install Media on Systems Running Windows
1. Access http://www.redhat.com/services/custom/cygwin/ and click the Red Hat Cygwin official
installation utility link. The rhsetup.exe executable will download.
2. As the Administrator user run the downloaded rhsetup.exe executable. The Red Hat
Cygwin installer will display.
3. Follow the prompts to complete a standard installation of Red Hat Cygwin. The Coreutils package within the Base package group provides the dd utility. This is automatically selected for installation.
4. Copy the rhev-hypervisor.iso file downloaded from Red Hat Network to C:\rhev-
hypervisor.iso.
5. As the Administrator user run Red Hat Cygwin from the desktop. A terminal window will appear.
Important — Run Red Hat Cygwin as Administrator
On the Windows 7 and Windows Server 2008 platforms it is necessary to right click the
Red Hat Cygwin icon and select the Run as Administrator... option to ensure the application runs with the correct permissions.
6. In the terminal run cat /proc/partitions to see the drives and partitions currently visible to the system.
Example 7.3. View of Disk Partitions Attached to System
Administrator@test /
$ cat /proc/partitions major minor #blocks name
8 0 15728640 sda
8 1 102400 sda1
8 2 15624192 sda2
4 9
Red Hat Enterprise Virtualization 3.0 Installation Guide
7. Plug the USB storage device which is to be used as the media for the hypervisor installation into the system. Re-run the cat /proc/partitions command and compare the output to that of the previous run. A new entry will appear which designates the USB storage device.
Example 7.4 . View of Disk Partitions Attached to System
Administrator@test /
$ cat /proc/partitions major minor #blocks name
8 0 15728640 sda
8 1 102400 sda1
8 2 15624192 sda2
8 16 524288 sdb
8. Use the dd command to copy the rhev-hypervisor.iso file to the disk. The example uses a
USB storage device named /dev/sdb. Replace sdb with the correct device name for the USB storage device to be used.
Example 7.5. Use of dd Command Under Red Hat Cygwin
Administrator@test /
$ dd if=/cygdrive/c/rhev-hypervisor.iso of=/dev/sdb& pid=$!
The provided command starts the transfer in the background and saves the process identifier so that it can be used to monitor the progress of the transfer. Refer to the next step for the command used to check the progress of the transfer.
Warning — All Data on the Device Specified will be Overwritten
The dd command will overwrite all data on the device specified for the of parameter. Any existing data on the device will be destroyed. Ensure that the correct device is specified and that it contains no valuable data before invocation of the dd command.
9. Transfer of the ISO file to the USB storage device with the version of dd included with Red Hat
Cygwin can take significantly longer than the equivalent on other platforms.
To check the progress of the transfer in the same terminal window that the process was started in send it the USR1 signal. This can be achieved by issuing the kill in the terminal window as follows: kill -USR1 $pid
10. When the transfer operation completes the final record counts will be displayed.
Example 7.6. Result of dd Initiated Copy
210944+0 records in
210944+0 records out
108003328 bytes (108 MB) copied, 2035.82 s, 53.1 kB/s
[1]+ Done dd if=/cygdrive/c/rhev-hypervisor.iso of=/dev/sdb
50
Chapter 7. Installing the Red Hat Enterprise Virtualization Hypervisor
Result:
The USB storage device (/dev/sdb) is ready to boot a hypervisor.
7.1.2.2. Booting a Hypervisor USB Storage Device
Booting a hypervisor from a USB storage device is similar to booting other live USB operating systems.
To boot from a USB storage device:
1. Enter the system's BIOS menu to enable USB storage device booting if not already enabled.
a. Enable USB booting if this feature is disabled.
b. Set booting USB storage devices to be first boot device.
c. Shut down the system.
2. Insert the USB storage device that contains the hypervisor boot image.
3. Restart the system.
Result:
The hypervisor will boot automatically.
“Booting from the Installation Media” for details.
7.1.3. Preparing a Hypervisor from a CD-ROM or DVD
It is possible to install the hypervisor with a CD-ROM or DVD.
7.1.3.1. Making a Hypervisor CD-ROM Boot Disk
Burn the hypervisor image to a CD-ROM with the cdrecord command. The cdrecord command is part of the cdrecord package which is installed on Red Hat Enterprise Linux by default.
1. Verify that the cdrecord package is installed on the system.
Example 7.7. Verify Installation of cdrecord Package
# rpm -q cdrecord cdrecord-2.01-10.7.el5
If the package version is in the output the package is available.
If it is not listed, install cdrecord:
# yum install cdrecord
2. Insert a blank CD-ROM or DVD into your CD or DVD writer.
3. Record the ISO file to the disc. The cdrecord command uses the following: cdrecord dev=device /iso/file/path/
This example uses the first CD-RW (/dev/cdrw) device available and the default hypervisor image location, /usr/share/rhev-hypervisor/rhev-hypervisor.iso.
51
Red Hat Enterprise Virtualization 3.0 Installation Guide
Example 7.8. Use of cdrecord Command
# cdrecord dev=/dev/cdrw /usr/share/rhev-hypervisor/rhev-hypervisor.iso
Result:
If no errors occurred, the hypervisor is ready to boot. Errors sometimes occur during the recording process due to errors on the media itself. If this occurs insert another writable disk and repeat the command above.
The hypervisor uses a program (isomd5sum) to verify the integrity of the installation media every time the hypervisor is booted. If media errors are reported in the boot sequence you have a bad CD-ROM.
Follow the procedure above to create a new CD-ROM or DVD.
7.1.3.2. Booting a Hypervisor CD-ROM
For many systems, the default BIOS configuration boots from CD-ROM first. If booting from CD-ROM is disabled or is not the first boot device refer to BIOS Settings and Boot Process Troubleshooting and your manufacturers manuals for more information.
To boot from CD-ROM insert the hypervisor CD-ROM and then restart the computer.
The hypervisor will start to boot. If the hypervisor does not start to boot your BIOS may not be configured to boot from CD-ROM first or booting from CD-ROM may be disabled.
“Booting from the Installation Media” for details.
7.2. Installation
This chapter documents the installation of the Red Hat Enterprise Virtualization hypervisor. Red Hat
Enterprise Virtualization Hypervisors are able to use Storage Area Networks (SANs) and other network storage for storing virtualized guest images. Hypervisors can be installed on SANs, provided that the
Host Bus Adapter (HBA) permits configuration as a boot device in BIOS.
Hypervisors are able to use multipath devices for installation. Multipath is often used for SANs or other networked storage. Multipath is enabled by default at install time. Any block device which responds to
scsi_id functions with multipath. Devices where this is not the case include USB storage and some older ATA disks.
There are two methods for installing Red Hat Enterprise Virtualization Hypervisors:
Interactive Installation (see Section 7.2.1, “Interactive Installation”
).
Automated Installation with Kernel Parameters (see the Red Hat Enterprise Linux — Hypervisor
Deployment Guide).
7.2.1. Interactive Installation
Red Hat Enterprise Virtualization Hypervisors must be installed on physical servers, not virtual machines.
The instructions in this section cover installation on a single system. When deploying on multiple systems always remember to use unique hostnames and IP addresses to avoid networking conflicts.
52
Chapter 7. Installing the Red Hat Enterprise Virtualization Hypervisor
7.2.1.1. Booting from the Installation Media
There are several methods for booting hypervisors, refer to Section 7.1, “Installation Media”
for detailed instructions on preparing boot media for Red Hat Enterprise Virtualization Hypervisor installation.
Procedure 7.3. Booting from the Installation Media
1. Insert the Red Hat Enterprise Virtualization Hypervisor installation media.
2. Power on the system and ensure the system boots from the installation media.
3. The boot splash screen appears. If no input is provided, the hypervisor installation will commence in 30 seconds, using default kernel parameters.
Figure 7.1. Boot Splash Screen
4. To modify the boot options, press any key. The boot menu will display.
53
Red Hat Enterprise Virtualization 3.0 Installation Guide
54
Figure 7.2. Boot Menu Screen
The following boot options are available:
Boot
Boot the hypervisor installer.
Boot with Serial Console
Boot the hypervisor installer, with the console redirected to a serial device attached to
/dev/ttyS0.
Boot from Local Drive
Boot the operating system installed on the first local drive.
Select the appropriate boot option from the boot menu.
5. Where required additional kernel parameters should be appended to the default parameters displayed. A press of the Enter key boots the hypervisor installation with the default kernel parameters. Alternatively press the Tab key to edit kernel parameters for the selected boot option.
Chapter 7. Installing the Red Hat Enterprise Virtualization Hypervisor
Figure 7.3. Boot Parameter Screen
Result:
The hypervisor boots with the provided boot options.
Important — Kernel Parameters
In edit mode you are able to add or remove kernel parameters from the list. Kernel parameters must be separated from each other by a space. Once the desired kernel parameters have been set press Enter to boot the system. Alternatively pressing Esc reverts any changes that you have made to the kernel parameters.
For more information on the kernel parameters, see the Red Hat Enterprise Linux — Hypervisor
Deployment Guide.
Note — Upgrading Existing Hypervisors
To upgrade an existing hypervisor installation, the kernel must be booted with the upgrade parameter. This will automatically upgrade and reboot the system, rather than displaying the interactive configuration menu. For more information, see the Red Hat Enterprise Linux —
Hypervisor Deployment Guide.
55
Red Hat Enterprise Virtualization 3.0 Installation Guide
7.2.1.2. Installation Procedure
When the hypervisor is first booted the interactive installation script starts. This script facilitates installation of the Red Hat Enterprise Virtualization Hypervisor using graphical prompts. The following keys are be used to manipulate the screens which support hypervisor installation.
Menu Actions
The directional keys (Up, Down, Left, Right) are used to select different controls on the screen.
Alternatively the Tab key cycles through the controls on the screen which are enabled.
Text fields are represented by a series of underscores (_). To enter data in a text field select it and begin entering data.
Buttons are represented by labels which are enclosed within a pair of angle brackets (< and >). To activate a button ensure it is selected and press Enter or Space.
Boolean options are represented by an asterisk (*) or a space character enclosed within a pair of square brackets ([ and ]). When the value contained within the brackets is an asterisk then the option is set, otherwise it is not. To toggle a Boolean option on or off press Space while it is selected.
Procedure 7.4 . Hypervisor Installation
1. To commence Hypervisor installation select Install Hypervisor and press Enter.
2. Disk Configuration
The installation script automatically detects all disks attached to the system. This information is used to assist with selection of the boot and installation disks that the hypervisor should use.
Each entry displayed on these screens indicates the Location, Device Name, and Size
(GB) of the relevant disk.
a. Boot disk
The first disk selection screen is used to select the disk from which the hypervisor will boot.
The hypervisor's boot loader will be installed to the Master Boot Record (MBR) of the disk that is selected on this screen. The hypervisor attempts to automatically detect the disks attached to the system and presents the list from which you choose the boot device.
Alternatively you are able to manually select a device, by specifying a block device name, by enabling the Other Device option.
Important — Boot Order
The disk selected must be identified as a boot device and appear in the boot order either in the system's BIOS or in a pre-existing boot loader.
A. Automatically Detected Device Selection a. Select the entry for the disk the hypervisor is to boot from in the list.
b. Select the <Continue> button and press Enter. This action will save the boot device selection and start the next step of installation.
B. Manual Device Selection a. Select the Other Device entry from the list.
b. Select the <Continue> button and press Enter.
c. When prompted to Please enter the disk to use for booting RHEV
Hypervisor enter the name of the block device from which the hypervisor should boot.
56
Chapter 7. Installing the Red Hat Enterprise Virtualization Hypervisor
Example 7.9. Other Device Selection
Please enter the disk to use for booting RHEV Hypervisor
/dev/sda d. Select the <Continue> button and press Enter. This action will save the boot device selection and start the next step of installation.
Once a disk has been selected it is necessary to select the <Continue> button and press
Enter to save the selection and continue with hypervisor installation.
b. Installation Disk(s)
The disk(s) selected for installation will be those to which the hypervisor itself is installed.
The hypervisor attempts to automatically detect the disks attached to the system and presents the list from which installation devices are chosen.
Warning — Data Loss
All data on the selected storage device(s) will be destroyed.
a. Select each disk which the hypervisor is to use for installation and press Space to toggle it to enabled. Repeat this step for all disks you want the hypervisor to use.
Where other devices are to be used for installation, either solely or in addition to those which are listed automatically, enable the Other Device option.
b. Select the <Continue> button and press Enter to continue.
c. Where the Other Device option was specified a further prompt will appear. Enter the name of each additional block device to use for hypervisor installation separated by a comma. Once all required disks have been selected then select the
<Continue> button and press Enter.
Example 7.10. Other Device Selection
Please select the disk(s) to use for installation of RHEV
Hypervisor
Enter multiple entries separated by commas
/dev/mmcblk0,/dev/mmcblk1______________
Once the installation disk, or disks, have been selected the next stage of the installation starts.
3. Password
The hypervisor requires that a password be set to protect local console access by the admin user. The installation script prompts you to enter the desired password in both the Password and
Confirm Password fields.
A strong password must be used. Strong passwords consist of a mix of uppercase, lowercase, numeric, and punctuation characters. They are six or more characters long and do not contain dictionary words.
Once a strong password has been entered select <Install> and press Enter to install the hypervisor to disk.
Result:
57
Red Hat Enterprise Virtualization 3.0 Installation Guide
Once installation is complete the message RHEV Hypervisor Installation Finished
Successfully will be displayed. Select the <Restart> button and press Enter to reboot the system.
Further post installation configuration is required to connect the hypervisor to the Red Hat Enterprise
Virtualization Manager. See Section 7.3, “Configuration”
for further details.
Note — Remove Boot Media
The boot media should be removed and the boot device order changed to prevent the installation sequence restarting after the system reboots.
7.3. Configuration
7.3.1. Logging In
The hypervisor allows local console logins to facilitate post-installation configuration. The login prompt used is displayed once the hypervisor has booted:
Please login as 'admin' to configure the node localhost login:
Type admin at the prompt and press Enter. When prompted enter the password which was set during the installation process and press Enter again to log in.
The hypervisor configuration menu will then be displayed. The menu facilitates interactive configuration of the hypervisor. Throughout the remainder of this chapter it will be referred to as the main menu. The main menu provides access to multiple screens which report on the status and configuration of the hypervisor. They also provide the ability to change the hypervisor configuration.
The configuration interface is similar to that of the installation script. The same keys are used to
navigate the menu and associated screens. Refer to Menu Actions
to review the list of possible actions.
7.3.2. Status
The status screen displays a brief overview of the current state of the hypervisor. The information displayed consists of: the hostname, the current status of the network connection, the destination(s) of logs and reports, and the number of active virtual machines.
The status screen also provides a number of buttons to change the state of the hypervisor. They are:
<Lock>: Locks the hypervisor. The username and password must be entered to unlock the hypervisor.
<Restart>: Restarts the hypervisor.
<Power Off>: Turns the hypervisor off.
7.3.3. Network
The Network screen is used to configure:
58
Chapter 7. Installing the Red Hat Enterprise Virtualization Hypervisor the hypervisor's hostname, the DNS server(s) to use, the NTP server(s) to use, and the network interface to use.
Procedure 7.5. Hostname Configuration
1. To set or change the hostname select the Hostname field and enter the new hostname.
2. Select <Apply>, and press Enter to save changes to the hostname.
Result:
The hostname is updated.
Procedure 7.6. DNS Configuration
The hypervisor supports the specification of one or more Domain Name System (DNS) servers to use when resolving host and domain names.
1. To set or change the primary DNS server select the DNS Server 1 field and enter the IP address of the new primary DNS server to use.
2. To set or change the secondary DNS server select the DNS Server 2 field and enter the IP address of the new secondary DNS server to use.
3. Select <Apply>, and press Enter to save changes to the DNS configuration.
Result:
The primary and secondary DNS servers queried by the hypervisor are updated.
Procedure 7.7. NTP Configuration
The hypervisor supports the specification of one or more Network Time Protocol (NTP) servers with which the hypervisor should synchronize the system clock. It is important that the hypervisor is synchronized with the same time source as the Red Hat Enterprise Virtualization Manager. This ensures accurate time keeping across the Red Hat Enterprise Virtualization environment.
1. To set or change the primary NTP server select the NTP Server 1 field and enter the IP address or hostname of the new primary NTP server to use.
2. To set or change the secondary NTP server select the NTP Server 2 field and enter the IP address or hostname of the new secondary NTP server to use.
3. Select <Apply>, and press Enter to save changes to the NTP configuration.
Result:
The primary and secondary NTP servers queried by the hypervisor are updated.
Procedure 7.8. Network Interface Configuration
For each network interface detected the hypervisor will display the:
Device,
Status,
Model, and
59
Red Hat Enterprise Virtualization 3.0 Installation Guide
MAC Address.
At least one network interface must be configured before the hypervisor is able to connect with the Red
Hat Enterprise Virtualization Manager.
1. Device Identification
Select the network interface to be configured from the list and press Enter.
In some cases it may be unclear which physical device an entry in the list refers to. Where this is the case the hypervisor is able to blink the physical device's network traffic lights to assist with identification. To make use of this facility select the entry from the list and, then select the <Flash
Lights to Identify> button. Press Enter and, take note of which physical device's lights start blinking. The configuration screen for the selected device will be displayed.
2. IPv4 Settings
The hypervisor supports both dynamic (DHCP), and static IPv4 network configuration.
A. Dynamic (DHCP) Network Configuration
Dynamic network configuration allows the hypervisor to be dynamically assigned an IP address via DHCP. To enable dynamic IPv4 network configuration select the DHCP option under IPv4
Settings and press Space to toggle it to enabled.
B. Static Network Configuration
Static network configuration allows the hypervisor to be manually assigned an IP address. To enable static IPv4 network configuration select the Static option under IPv4 Settings and press Space to toggle it to enabled.
Selection of the Static option enables the IP Address, Netmask, and Gateway fields. The
IP Address, Netm ask, and Gateway fields must be populated to complete static network configuration.
In particular it is necessary that: the IP Address is not already in use on the network, the Netmask matches that used by other machines on the network, and the Gateway matches that used by other machines on the network.
Where it is not clear what value should be used for the IP Address, Netmask, or Gateway field consult the network's administrator or consider a dynamic configuration.
Example 7.11. Static IPv4 Networking Configuration
IPv4 Settings
[ ] Disabled [ ] DHCP [*] Static
IP Address: 192.168.122.100_ Netmask: 255.255.255.0___
Gateway 192.168.1.1_____
60
3. IPv6 Settings
The Red Hat Enterprise Virtualization Manager does not currently support IPv6 networking. IPv6 networking must remain set to Disabled.
4. VLAN Configuration
If VLAN support is required then populate the VLAN ID field with the VLAN identifier for the selected device.
5. Save Network Configuration
Once all networking options for the selected device have been set the configuration must be saved.
a. Select the <Apply> button and press Enter to save the network configuration.
Chapter 7. Installing the Red Hat Enterprise Virtualization Hypervisor b. The Confirm Network Settings dialog box will appear. Ensure that the Ok button is selected and press Enter to confirm.
Result:
The Network screen is displayed. The device is listed as Configured.
7.3.4. Security
The Security screen is used to change the admin password for both local and remote access. SSH password authentication is also enabled or disabled via this screen.
Procedure 7.9. Change Security Configuration
1. Enable SSH Password Authentication
To enable SSH password authentication for remote access select the Enable ssh password
authentication option and press Space to toggle it to enabled.
2. Change admin Password a. Enter the desired admin password in the Password field. You should use a strong password.
Strong passwords contain a mix of uppercase, lowercase, numeric and punctuation characters. They are six or more characters long and do not contain dictionary words.
b. Enter the desired admin password in the Confirm Password field. Ensure that the value entered in the Confirm Password field matches the value entered in the Password field exactly. Where this is not the case an error message will be displayed to indicate that the two values are different.
3. Select <Apply> and press Enter to save the security configuration.
Result:
The security configuration has been updated.
7.3.5. Logging
The hypervisor creates and updates a number of log files. The Logging screen allows configuration of a daemon to automatically export these log files to a remote server.
Procedure 7.10. Change Logging Configuration
1. Logrotate Configuration
The logrotate utility simplifies the administration of log files. The hypervisor uses logrotate to rotate logs when they reach a certain file size.
Log rotation involves renaming the current log(s) and starting new ones in their place. The
Logrotate Max Log Size value set on the Logging screen is used to determine when a log should be rotated.
Enter the Logrotate Max Log Size in kilobytes. The default maximum log size is 1024 kilobytes.
2. Rsyslog Configuration
The rsyslog utility is a multithreaded syslog daemon. The hypervisor is able to use rsyslog to transmit log files over the network to a remote syslog daemon. For information on setting up the remote syslog daemon consult the Red Hat Enterprise Linux — Deployment Guide.
a. Enter the remote Rsyslog server address in the Server Address field.
61
Red Hat Enterprise Virtualization 3.0 Installation Guide b. Enter the remote Rsyslog server port in the Server Port field. The default port is 514.
3. netconsole Configuration
The netconsole module allows kernel messages to be sent to a remote machine. The hypervisor uses netconsole to transmit kernel messages over the network.
a. Enter the Server Address.
b. Enter the Server Port. The default port is 6666.
4. Save Configuration
To save the logging configuration select <Apply> and press Enter.
Result:
The logging configuration has been updated and logs will be exported to the remote Rsyslog server specified.
7.3.6. Kernel Dump
Red Hat Enterprise Virtualization hypervisor hosts generate a kernel dump (a kdump file) in the event of a system failure. These kdump files are essential for debugging and support.
The hypervisor supports the export of kernel dumps by kdump using NFS or SSH so that they may be analyzed at a later date. The Kernel Dump screen provides for configuration of this facility.
Procedure 7.11. kdump Configuration
1. Kernel Configuration
Crash dumps generated by kdump are exported over NFS or SSH. Select the desired transfer method and press Space to enable it.
For the export method chosen a location to which the kdump files should be exported must also be specified.
a. NFS location
Set the NFS location to which crash logs should be exported in the NFS Location field.
The NFS Location should be the full NFS path which includes fully qualified domain name and directory path.
Example 7.12. NFS Location exam ple.redhat.com :/var/crash
b. SSH location
Set the SSH location to which crash logs should be exported in the SSH Location field.
The SSH Location should be the full SSH login which includes the fully qualified domain name and username.
Example 7.13. SSH Location root@ exam ple.redhat.com
2. Save Configuration
To save the configuration the user must select <Apply> and press Enter.
Result:
The Kernel Dump configuration has been updated and kernel dumps will be exported to the remote server(s) specified.
62
Chapter 7. Installing the Red Hat Enterprise Virtualization Hypervisor
7.3.7. Remote Storage
The hypervisor supports the use of a remote iSCSI initiator for storage. The iSCSI initiator to use is set from the Remote Storage screen.
Procedure 7.12. Remote Storage Configuration
1. iSCSI Initiator Name
Enter the initiator name in the iSCSI Initiator Name field.
Example 7.14 . iSCSI Initiator Name iqn.1994 -05.com .redhat:5189835eeb4 0
2. Save Configuration
To save the configuration the user must select <Apply> and press Enter.
Result:
The Remote Storage configuration has been updated.
7.3.8. RHEV-M
The hypervisor is able to attach itself to the Red Hat Enterprise Virtualization Manager immediately if the address of the manager is available. Where the manager has not yet been installed you must instead set a password. This allows the hypervisor to be added from the Administration Portal once the manager has been installed. Both modes of configuration are supported from the RHEV-M screen.
Important — Security Considerations
Setting a password on the RHEV-M configuration screen sets the hypervisor's root password and enables SSH password authentication. Once the hypervisor has successfully been added to the manager it is recommended SSH password authentication is disabled.
Procedure 7.13. RHEV-M Configuration
1. A. Configuration Using a Management Server Address a. Enter the IP address or fully qualified domain name of the manager in the Management
Server field.
b. Enter the management server port in the Management Server Port field. The default value is 8443. Where a different port was selected during Red Hat Enterprise
Virtualization Manager installation then it should be specified here, replacing the default value.
c. Enable the Verify RHEVM Certificate option if you wish to verify that the finger print of the certificate retrieved from the management server you specified is correct.
The value that the certificate finger print should be compared against is returned at the end of Red Hat Enterprise Virtualization Manager installation.
d. Leave the Password and Confirm Password fields blank, these fields are not required if the address of the management server is known.
B. Configuration Using a Password a. Enter a password in the Password field. It is recommended that you use a strong password. Strong passwords contain a mix of uppercase, lowercase, numeric and punctuation characters. They are six or more characters long and do not contain
63
Red Hat Enterprise Virtualization 3.0 Installation Guide dictionary words.
b. Re-enter the password in the Confirm Password field.
c. Leave the Management Server and Management Server Port fields blank. As long as a password is set, allowing the hypervisor to be added to the manager later, these fields are not required.
2. Save Configuration
To save the configuration select <Apply> and press Enter.
Result:
The RHEV-M configuration has been updated.
7.3.9. Red Hat Network
Guests running on the hypervisor may need to consume Red Hat Enterprise Linux virtualization entitlements. Where this is the case the hypervisor must be registered to Red Hat Network or a Satellite server. The hypervisor is able to connect to these services via a HTTP proxy where one is in use.
Note that when new versions of the hypervisor itself become available they are installed from the Red
Hat Enterprise Virtualization Manager, not Red Hat Network.
Procedure 7.14 . Register with Red Hat Network
1. Authentication
Enter your Red Hat Network username in the Login field.
Enter your Red Hat Network password in the Password field.
2. Profile Name
Enter the profile name to be used for the system in the Profile Name field. This is the name that the system will appear under when viewed via the Red Hat Network.
3. Update Source
Guests running on the hypervisor may need to consume Red Hat Enterprise Linux virtualization entitlements. Where this is the case the hypervisor must be registered to Red Hat Network or, if available, either a Satellite installation or a Subscription Asset Manager. The hypervisor is able to connect to these services via a HTTP proxy where one is in use.
Note that when new versions of the hypervisor itself become available they are installed from the
Red Hat Enterprise Virtualization Manager, not Red Hat Network.
A. To Connect Directly to RHN
Select the RHN option and press Space to toggle it to enabled. The URL and CA values do not need to be provided.
Example 7.15. Red Hat Network Configuration
[*] RHN [ ] Satellite [ ] Subscription Asset Manager
URL: ________________________________________
CA : ________________________________________
B. To Connect via Satellite a. Select the Satellite option and press Space to toggle it to enabled.
b. Enter the URL of the Satellite server in the URL field.
c. Enter the URL of the Certificate Authority for the Satellite server in the CA field.
64
Chapter 7. Installing the Red Hat Enterprise Virtualization Hypervisor
Example 7.16. Satellite Configuration
[ ] RHN [*] Satellite [ ] Subscription Asset Manager
URL: https://your-satellite.example.com
CA : https://your-satellite.example.com/pub/RHN-ORG-TRUSTED-SSL-CERT
C. To Connect via Subscription Asset Manager a. Select the Subscription Asset Manager option and press Space to toggle it to enabled.
b. Enter the URL of the Subscription Asset Manager server in the URL field.
c. Enter the URL of the Certificate Authority for the Subscription Asset Manager server in the CA field.
Example 7.17. Subscription Asset Manager Configuration
[ ] RHN [ ] Satellite [*] Subscription Asset Manager
URL: https://subscription-asset-manager.example.com
CA : https://subscription-asset-manager.example.com/pub/RHN-ORG-
TRUSTED-SSL-CERT
4. HTTP Proxy
Where a HTTP proxy is in use the details to connect to it must be provided. To connect to the Red
Hat Network or a Satellite server via a proxy you must enter: the proxy Server's network address, the Port to connect to the proxy on, and optionally, the Username and Password to use to connect to the proxy.
In environments where a HTTP proxy is not in use it is safe to ignore this step.
Example 7.18. HTTP Proxy Configuration
HTTP Proxy
Server: proxy.example.com__ Port: 8080_
Username: puser________ Password: ******_______
5. Save Configuration
To save the configuration the user must select <Apply> and press Enter.
Result:
The Red Hat Network configuration has been updated.
7.4. Using the Hypervisor
Where the hypervisor was configured with the address of the Red Hat Enterprise Virtualization Manager it reboots and is automatically registered with it. The Red Hat Enterprise Virtualization Manager interface displays the hypervisor under the Hosts tab. To prepare the hypervisor for use, it must be approved using Red Hat Enterprise Virtualization Manager.
Procedure 7.15. Approving a Red Hat Enterprise Virtualization Hypervisor
1. Login to the Red Hat Enterprise Virtualization Manager Administration Portal.
65
Red Hat Enterprise Virtualization 3.0 Installation Guide
2. From the Hosts tab, click on the host to be approved. The host should currently be listed with the status of Pending Approval.
3. Click the Approve button. The Edit and Approve Hosts dialog displays. You can use the dialog to set a name for the host and configure power management, where the host has a supported power management card. For information on power management configuration, see the
Power Management chapter of the Red Hat Enterprise Virtualization — Administration Guide.
4. Click OK. If you have not configured power management you will be prompted to confirm that you wish to proceed without doing so, click OK.
Result:
The status in the Hosts tab changes to Installing, after a brief delay the host status changes to Up.
Where the hypervisor was configured without the address of the Red Hat Enterprise Virtualization
Manager it needs to be added manually. To add the hypervisor manually you must have both the IP address of the machine upon which it was installed and the password that was set on the RHEV-M screen during configuration.
Procedure 7.16. Adding a Red Hat Enterprise Virtualization Hypervisor with a Password
1. Login to the Red Hat Enterprise Virtualization Manager Administration Portal.
2. From the Hosts tab, click New. The New Host dialog displays.
3. Enter the details of the new host.
Nam e: a descriptive name for the host.
Address: the IP address, or resolvable hostname of the host (provided during installation).
Port: the port used for internal communication control between the hosts. A default port is displayed; change the default only if you are sure that another port can be used.
Host Cluster: the cluster to which the host belongs (select from the drop-down list).
Root password: the password of the designated host; used during installation of the host.
4. Optionally, configure power management, where the host has a supported power management card. For information on power management configuration, see the Power Management chapter of the Red Hat Enterprise Virtualization — Administration Guide.
5. Click OK.
Result:
The added hypervisor displays in the list of hosts. Once the host is successfully connect its status changes to Up.
66
Chapter 8. Installing Red Hat Enterprise Linux Hosts
Chapter 8. Installing Red Hat Enterprise Linux Hosts
Virtual machines on Red Hat Enterprise Linux can be managed by Red Hat Enterprise Virtualization
Manager. Red Hat Enterprise Linux hosts can be used concurrently with Red Hat Enterprise
Virtualization Hypervisors.
Important
Only the AMD64/Intel 64 version of Red Hat Enterprise Linux is compatible for use with Red Hat
Enterprise Virtualization.
8.1. Adding Red Hat Enterprise Linux Hosts
Red Hat Enterprise Virtualization also supports hosts running Red Hat Enterprise Linux AMD64/Intel 64 version. This section describes the preparatory steps for installing the Red Hat Enterprise Linux host, as well as the steps to manually add the host to the Red Hat Enterprise Virtualization platform.
Adding a host can take some time, as the following steps are completed by the platform: virtualization checks, installation of packages, creation of bridge and a reboot of the host. Use the Details pane to monitor the hand-shake process as the host and management system establish a connection.
The following table shows which versions of Red Hat Enterprise Linux are supported as hosts for each version of Red Hat Enterprise Virtualization.
Red Hat Enterprise
Linux Version
5.6+
6.2+
Red Hat Enterprise
Virtualization 2.2
clusters
Supported
Unsupported
Red Hat Enterprise
Virtualization 3.0
clusters
Unsupported
Supported
Red Hat Enterprise
Virtualization 3.0
clusters in 2.2
compatibility mode
Supported
Supported
8.1.1. Preparing Red Hat Enterprise Linux Hosts
To ensure a smooth and successful integration of Red Hat Enterprise Linux Hosts and Red Hat
Enterprise Virtualization platform, prepare the host carefully according to the instructions in this section.
Procedure 8.1. Directions:
1. Install Red Hat Enterprise Linux
Ensure that Red Hat Enterprise Linux is correctly installed and configured on the physical host.
Refer to the Red Hat Enterprise Linux Installation Guide for more information. Only the Base package group is required. All other packages can be removed or not selected.
Warning — DNS Configuration
The Red Hat Enterprise Linux host must have a fully resolvable network address. Valid forward and reverse lookups for the address must be available in DNS. Virtual machine migration will not work in environments where this is not the case.
67
Red Hat Enterprise Virtualization 3.0 Installation Guide
68
Important — Provide Access to Authentication Files
If you are using proprietary directory services or standard directory services with no access to authentication files for user management, the vdsm package will fail to create the required system user. The authentication files required by the useradd command must be accessible to the installer. Red Hat Directory Server (RHDS) recommends a security policy with a mixture of local files and LDAP. Following this recommendation will resolve this issue.
2. Configure VLANs
If you are using VLAN, ensure that VLANs are configured for access to the Red Hat Enterprise
Virtualization Manager.
3. Check Red Hat Network Subscriptions
Ensure the host is correctly subscribed to the Red Hat Enterprise Virt Management
Agent (v 6 x86_64 ) channel in Red Hat Network, also referred to as rhel-x86_64 -rhev-
m gm t-agent-6, on Red Hat Network. If you do not have the appropriate subscription entitlements, contact Red Hat Customer Service.
a. If the machine has not already been registered with Red Hat Network, run the
rhn_register command as root to register it. To complete registration successfully you will need to supply your Red Hat Network username and password. Follow the onscreen prompts to complete registration of the system.
# rhn_register b. You must now add a subscription to the Red Hat Enterprise Virt Management
Agent (v 6 x86_64 ) channel to the machine. To add the channel subscription to the system from the Red Hat Network web interface:
1. Log on to Red Hat Network ( http://rhn.redhat.com
).
2. Click Systems at the top of the page.
3. Select the system to which you are adding channels from the list presented on the screen, by clicking the name of the system.
4. Click Alter Channel Subscriptions in the Subscribed Channels section of the screen.
5. Select the Red Hat Enterprise Virt Management Agent (v 6 x86_64) channel from the list presented on the screen, then click the Change
Subscription button to finalize the change.
4. Edit hosts file
Add a manual host entry to the /etc/hosts file (on the Red Hat Enterprise Linux host) for the
Red Hat Enterprise Virtualization Manager server to enable vdsm and other services to connect properly to the host.
Because Active Directory uses layered domain names, the Active Directory instance takes the domain name usually used by a Linux host. For example, if the server running the Red Hat
Enterprise Virtualization Manager has a hostname of server1.example.com, Active Directory uses that address and creates a sub-address named rhev-
m anager.server1.exam ple.com .
Edit the /etc/hosts file on the Red Hat Enterprise Linux Host. The following screen output sample resembles the contents of the file:
Chapter 8. Installing Red Hat Enterprise Linux Hosts
127.0.0.1 localhost.localdomain localhost
::1 localhost6.localdomain6 localhost6
Append a new line to /etc/hosts with the IP address and both variants of the Red Hat
Enterprise Virtualization Manager domain names. The following screen output sample resembles the required contents of the file:
127.0.0.1 localhost.localdomain localhost
::1 localhost6.localdomain6 localhost6
10.0.0.1 server1.example.com rhev-manager.server1.example.com
5. Open firewall ports
Red Hat Enterprise Virtualization platform uses a number of network ports for management and other virtualization features.
The following steps configure iptables to open the required ports. These steps replace any existing firewall configuration with that required for Red Hat Enterprise Virtualization Manager. If you have existing firewall rules with which this configuration must be merged then you must manually edit the rules defined in the iptables configuration file, /etc/sysconfig/iptables.
a. Remove and existing firewall rules.
# iptables --flush b. Add the ports required by Red Hat Enterprise Virtualization Manager to the iptables rules.
# iptables --append INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT
# iptables --append INPUT -p icmp -j ACCEPT
# iptables --append INPUT -i lo -j ACCEPT
# iptables --append INPUT -p tcp --dport 22 -j ACCEPT
# iptables --append INPUT -p tcp --dport 16514 -j ACCEPT
# iptables --append INPUT -p tcp --dport 54321 -j ACCEPT
# iptables --append INPUT -p tcp -m multiport --dports 5634:6166 -j
ACCEPT
# iptables --append INPUT -p tcp -m multiport --dports 49152:49216 -j
ACCEPT
# iptables --append INPUT -j REJECT --reject-with icmp-host-prohibited
# iptables --append FORWARD -m physdev ! --physdev-is-bridged -j REJECT
--reject-with icmp-host-prohibited
Note
The provided iptables commands add firewall rules to accept network traffic on a number of ports. These include: port 22 for SSH, ports 5634 to 6166 for guest console connections, port 16514 for libvirt virtual machine migration traffic, ports 49152 to 49216 for VDSM virtual machine migration traffic, and port 54321 for the Red Hat Enterprise Virtualization Manager.
c. Save the modified rules.
69
Red Hat Enterprise Virtualization 3.0 Installation Guide
70
# service iptables save d. Ensure that the iptables service is configured to start on boot and has been restarted, or started for the first time if it wasn't already running.
# chkconfig iptables on
# service iptables restart
6. Configure sudo access
The Red Hat Enterprise Virtualization Manager makes use of sudo to perform operations as
root on the host. The default configuration stored in /etc/sudoers contains values to allow this. If this file has been modified since Red Hat Enterprise Linux installation these values may have been removed. As root run visudo to ensure that the /etc/sudoers contains the default configuration values. Where it does not they must be added.
# Allow root to run any commands anywhere root ALL=(ALL) ALL
7. Enable SSH access for root
The Red Hat Enterprise Virtualization management daemon accesses host machines via SSH. To do this it logs in as root with an encrypted key for authentication. To ensure that SSH is configured and root is able to use it to access the system follow these additional steps.
Warning
The first time the Red Hat Enterprise Virtualization Manager is connected to the host it will install an authentication key. In the process it will overwrite any existing keys which exist in
/root/.ssh/authorized_keys.
a. These steps assume that the openssh-server package is installed on the system. Where the package is not present use yum to install it.
# yum install openssh-server b. Use chkconfig to verify which run-levels SSH is enabled at.
# chkconfig --list sshd sshd 0:off 1:off 2:on 3:on 4:on 5:on 6:off
It is expected that the SSH daemon shows as on for run-levels 3, 4, and 5. This is the default configuration.
If the configuration on the host differs use chkconfig to enable it for the required runlevels. The /etc/init.d/sshd script can then be used to ensure the service is currently started.
# chkconfig --level 345 sshd on
# /etc/init.d/sshd start
To verify this operation as successful run chkconfig --list sshd again and check the output. It should now show the daemon as on at run-level 3, 4, and 5.
c. In Red Hat Enterprise Linux the default SSH daemon configuration allows remote login by
Chapter 8. Installing Red Hat Enterprise Linux Hosts the root user. This is also a requirement for the Red Hat Enterprise Virtualization Manager to successfully access the machine. In some cases administrator's may have disabled this ability.
To check whether or not this is the case search the /etc/ssh/sshd_config for the value PermitRootLogin. This must be done while logged in as root.
# grep PermitRootLogin /etc/ssh/sshd_config
PermitRootLogin no
Where PermitRootLogin is set to no the value must be changed to yes. To do this edit the configuration file.
# vi /etc/ssh/sshd_config
Once the updated configuration file has been saved the SSH daemon must be told to reload it.
# /etc/init.d/sshd reload
Reloading sshd: [ OK ]
The root user should now be able to access the system via SSH.
Result:
You can now add the correctly installed and configured Red Hat Enterprise Linux host to the Red Hat
Enterprise Virtualization platform.
8.1.2. To Add a Host
In the process of adding a host, you will need to provide the IP and password of the host. The manager then logs into the host to performs virtualization checks, install packages, create a network bridge and reboot the host. The process of adding a new host can take some time, the state of the process can be followed in the Details pane.
1. Click the Hosts tab. The Hosts tab displays a list of all hosts in the system.
Figure 8.1. List of Hosts
2. Click the New button. The New Host dialog displays.
71
Red Hat Enterprise Virtualization 3.0 Installation Guide
72
Figure 8.2. New Host Dialog
Enter the details of the new host.
Name: a descriptive name for the host.
Address: the IP address, or resolvable hostname of the host (provided during installation).
Port: the port used for internal communication control between the hosts. A default port is displayed; change the default only if you are sure that another port can be used.
Host Cluster: the cluster to which the host belongs (select from the drop-down list).
Root password: the password of the designated host; used during installation of the host.
Enable Power Management: Select this checkbox to turn out-of-band (OOB) power management on. If selected, the information for the following fields must also be provided.
The Address of the host. This is usually the address of the remote access card (RAC) on the host.
A valid User Name for the OOB management.
A valid, robust Password for the OOB management.
The Type of the OOB management device. Select the appropriate device from the drop down list.
alom apc bladecenter drac5
Sun Integrated Lights Out Manager (ILOM)
APC Master MasterSwitch network power switch
IBM Bladecentre Remote Supervisor
Adapter
Dell Remote Access Controller for Dell computers
Chapter 8. Installing Red Hat Enterprise Linux Hosts eps ilo ipmilan rsa rsb ePowerSwitch 8M+ network power switch
HP Integrated Lights Out standard
Intelligent Platform Management Interface
IBM Remote Supervisor Adaptor
Fujitsu-Siemens RSB management interface
WTI Network PowerSwitch wti
The Port to connect to OOB management.
Slot: The slot number in the blade chassis. This option is for blade systems only.
Options: Extra command line options for the fence agent. Detailed documentation of the options available is provided in the man page for each fence agent.
Secure: Some fence agents support both encrypted and unencrypted communications.
Select this option to enable encrypted communications.
Click the Test button to test the operation of the OOB management solution.
Red Hat Enterprise Virtualization recommends power management. Power management enables the system to fence a troublesome host using an additional interface.
Note
If the host is required to be Highly Available, power management must be enabled and configured.
3. Click OK.
Result:
The new host displays in the list of hosts with a status of Installing. Once installation is complete, the status will update to Reboot and then Awaiting. The host must be activated for the status to change to Up.
Note
View the process of the host installation on the Details pane.
8.2. Activating a Host
After a host has been added, or an existing host has been taken down for maintenance, it needs to be activated before it can be used. Red Hat Enterprise Linux 6.2, or higher, hosts need to be activated after being added or upgraded.
To activate a host:
1. In the Hosts tab (see Figure 8.1, “List of Hosts”
), select the host to be activated.
2. Click the Activate button.
Result:
The host status changes to Up. Virtual machines can now run on the host.
73
74
Red Hat Enterprise Virtualization 3.0 Installation Guide
Part IV. Environment Configuration
Part IV. Environment Configuration
75
Red Hat Enterprise Virtualization 3.0 Installation Guide
Chapter 9. Planning your Data Center
Successful planning is essential for a highly available, scalable Red Hat Enterprise Virtualization environment.
Although it is assumed that your solution architect has defined the environment before installation, the following considerations must be made when designing the system.
CPU
Virtual Machines must be distributed across hosts so that enough capacity is available to handle higher than average loads during peak processing. Average target utilization will be 50% of available CPU.
Memory
The Red Hat Enterprise Virtualization page sharing process overcommits up to 150% of physical memory for virtual machines. Therefore, allow for an approximately 30% overcommit.
Networking
When designing the network, it is important to ensure that the volume of traffic produced by storage, remote connections and virtual machines is taken into account. As a general rule, allow approximately 50
MBps per virtual machine.
It is best practice to separate disk I/O traffic from end-user traffic, as this reduces the load on the
Ethernet connection and reduces security vulnerabilities by isolating data from the visual stream. For
Ethernet networks, it is suggested that bonds (802.3ad) are utilized to aggregate server traffic types.
Note
It is possible to connect both the storage and Hypervisors via a single high performance switch.
For this configuration to be effective, the switch must be able to provide 30 GBps on the backplane.
High Availability
The system requires at least two hosts to achieve high availability. This redundancy is useful when performing maintenance or repairs.
9.1. Data Centers
Following Red Hat Enterprise Virtualization Manager installation it is necessary to define the data centers, and clusters, that you will use to organize your virtualization hosts. The installation process creates a data center, and associated cluster, called Default. The storage type of the data center is set based on the one selected during installation. If you wish to make use of other storage types then you will need to add additional data centers and clusters to support them.
9.1.1. Prerequisites for Setting up a Data Center
Before you create a new data center, prepare the following resources. The following tasks must be done at the host level, not from the Red Hat Enterprise Virtualization platform.
1. Setup and configure hosts. A host can be a Red Hat Enterprise Virtualization Hypervisor or a Red
Hat Enterprise Linux host. A cluster needs a minimum of one host, and at least one active host is
76
Chapter 9. Planning your Data Center required to connect the system to a storage pool.
2. Setup, configure and define storage. It is recommended that data centers have a minimum of two storage domains, one to store disk images of the virtual machines and one to store ISO images.
Set up the storage domains of the type required for the data center; NFS, iSCSI, FCP or Local. For example, for an NFS data center, create and mount the export directories.
3. Set up logical networks for the data center, cluster and the hosts. It is recommended that you have the IP addresses/domain names available for reference.
9.1.2. Working with Data Centers
This section describes how to configure, create and manage data centers. The data center is the highest level container for all physical and logical resources within a managed virtual environment. The data center is a collection of clusters of hosts. It owns the logical network (that is, the defined subnets for management, guest network traffic and storage network traffic) and the storage pool.
Figure 9.1. Data Centers
Red Hat Enterprise Virtualization contains a default data center at installation. Enterprises can set up new and additional data centers that can all be managed from the single Administration Portal. For example, an organization may have different data centers for different physical locations, business units, or for reasons of security. It is recommended that you do not remove the default data center, instead set up new appropriately named data centers.
The system administrator, as the superuser, can manage all aspects of the platform, that is, data centers, storage pools, users, roles and permissions by default; however more specific administrative roles and permissions can be assigned to other users. For example, the enterprise may need a data center administrator for a specific data center, or a particular cluster may need an administrator. All system administration roles for physical resources have a hierarchical permission system. For example, a data center administrator will automatically have permission to manage all the objects in that data center, storage, cluster and hosts; while a cluster administrator can manage all objects in the particular cluster.
9.1.3. Creating a New Data Center
A data center is a logical grouping of clusters of hosts. If you wish to create an additional data center, use the instructions in this section; if you wish to use the existing default data center then you may skip
77
Red Hat Enterprise Virtualization 3.0 Installation Guide
this process and begin creating clusters, see Section 9.2, “Clusters”
.
The Data Centers tab displays a list of data centers.
Figure 9.2. Data Centers Tab
1. Click the New button on the Data Centers tab. The New Data Center dialog displays.
2. Enter the Name and Description of the data center.
3. Select the storage Type of the data center. Select the storage appropriate to your data center; one of the following:
NFS iSCSI
FCP
Local Storage
4. Select the Compatibility Level of the data center, 2.2 or 3.0.
5. Click OK.
6. The Guide Me dialog displays a list of configuration tasks that must be completed before the data center can be activated. The data center configuration tasks can be done immediately or later.
78
Chapter 9. Planning your Data Center
Figure 9.3. New Data Center Guide Me Dialog
Click Configure Later to close the dialog.
Result:
The new data center is added, and appears in appropriate searches or lists of data centers, with a status of Uninitialized. An uninitialized data center typically requires further configuration, for example, storage domains must be attached to it. Either click the Configure Storage button on the
Guide Me dialog or select the new data center in the list, and click the Storage tab in the Details pane.
You can define existing storage for the data center, or attach existing storage domains to the data center.
9.2. Clusters
A cluster is a collection of physical hosts that share the same storage domains and have the same type of CPU. Because virtual machines can be migrated across hosts in the same cluster, the cluster is the highest level at which power and load-sharing policies can be defined. The Red Hat Enterprise
Virtualization platform contains a default cluster in the default data center at installation.
Every cluster in the system must belong to a data center, and every host in the system must belong to a cluster. This enables the system to dynamically allocate a virtual machine to any host in the applicable cluster, according to policies defined on the Cluster tab and in the Configuration tool during runtime, thus maximizing memory and disk space, as well as virtual machine uptime.
At any given time, after a virtual machine runs on a specific host in the cluster, the virtual machine can be migrated to another host in the cluster using Migrate. This can be very useful when a host is shut down for maintenance. The migration to another host in the cluster is transparent to the user, and the user continues working as usual. Note that a virtual machine cannot be migrated to a host outside the cluster.
9.2.1. Creating a Cluster
79
Red Hat Enterprise Virtualization 3.0 Installation Guide
Before creating a new cluster, ensure that there is at least one host available to be assigned to it. All hosts in a cluster must have CPUs belonging to the same family as that selected for the cluster.
Alternatively CPU models from a more recently released CPU family capable of exposing the same functionality may also be used.
Supported combinations are shown in the Cluster compatibility charts for AMD and Intel CPUs. Note that mixing of CPUs from different manufacturers within the same cluster is not possible under any circumstances.
Table 9.1. Cluster Compatibility Chart for AMD CPUs
Cluster CPU Name
AMD Opteron G1
AMD Opteron G2
AMD Opteron G3
AMD Opteron G1
Supported
-
-
AMD Opteron G2
Supported
Supported
-
AMD Opteron G3
Supported
Supported
Supported
Table 9.2. Cluster Compatibility Chart for Intel CPUs
Intel Conroe Intel Penryn Cluster CPU
Name
Intel Conroe
Family
Intel Penryn
Family
Intel Nehalem
Family
Intel Westmere
Family
Supported
-
-
-
Supported
Supported
-
-
Intel Nehalem
Supported
Supported
Supported
-
Intel Westmere
Supported
Supported
Supported
Supported
Important
The default rhevm network cannot be modified once a cluster has been attached to a data center. Any configuration required for the rhevm network, such as enabling VLAN tagging, must be performed before a cluster is attached, and the data center is still in the Uninitialized state.
Procedure 9.1. To create a new host cluster:
1. Click the Clusters tab. A list of clusters displays.
2. Click the New button on the Clusters tab.
The New Cluster dialog displays.
3. On the General tab, Select an existing Data Center from the list, the cluster Name and
Description. The name should not include spaces.
Select the CPU Name for the Cluster. All hosts in the Cluster must have this model of CPU, or a newer model capable of exposing the same functionality. The CPU Name list displays all the CPU models supported by Red Hat Enterprise Virtualization. Finally on the General tab, select the
Com patibility Level of the data center, from either 2.2 or 3.0.
4. Use the Memory Optimization tab to define how much of the host's memory can be used in
80
Chapter 9. Planning your Data Center excess of the permitted memory for a virtual machine in the cluster. For example, all virtual machines will not be using the full amount of allocated memory all the time. Memory sharing allows virtual machines that require additional memory at a certain time to use memory that is not being used at that time by other virtual machines. This feature allows you to fine tune how you wish to optimize the memory page sharing and large pages implementation on the hosts in the cluster.
Select from None, that disables memory page sharing, Optimized for Server Load, that sets the memory page sharing threshold to 150% of the system memory on each host, or
Optim ized for Desktop Load, that sets the memory page sharing threshold to 200% of the system memory on each host.
5. Select the Resilience Policy tab to define if high availability is to be implemented for the virtual machines in the cluster. If a host shuts down unexpectedly or is put into maintenance, the virtual machines running on the host can be re-run on another host in the same cluster. This field allows you to configure the migration settings for virtual machines.
Select from Migrate Virtual Machines, (migrates all machines); Migrate only Highly
Available Virtual Machines or Do Not Migrate Virtual Machines.
6. Click OK to create the cluster. The new host cluster is added to the data center and displays on the Cluster tab.
The New Cluster - Guide Me dialog displays.
7. The Guide Me tab prompts you to add hosts to the new cluster. Click the Configure Hosts button, the New Host dialog displays.
Enter the details of the host to assign to the cluster. Click OK to close the New Host dialog. Now click Configure Later to close the New Cluster Guide Me dialog and return to the
Clusters tab.
Result:
The Hosts tab on the Details pane displays the newly added hosts.
81
Red Hat Enterprise Virtualization 3.0 Installation Guide
Chapter 10. Network Setup
This chapter provides instruction on configuring networking for the Red Hat Enterprise Virtualization environment. For information about managing networking, including maintenance, refer to the Red Hat
Enterprise Virtualization Administration Guide.
Red Hat Enterprise Virtualization uses networking to support almost every aspect of operations.
Storage, host management, user connections, and virtual machine connectivity, for example, all rely on a well planned and configured network to deliver optimal performance. Setting up networking is a vital prerequisite for a Red Hat Enterprise Virtualization environment because it is much simpler to plan for your projected networking requirements and implement your network accordingly than it is to discover your networking requirements through use and attempt to alter your network configuration retroactively.
A familiarity with the network concepts and their use is highly recommended when planning and setting up networking in a Red Hat Enterprise Virtualization environment. This document does not describe the concepts, protocols, requirements or general usage of bonds, bridges and logical networks. It is recommended that you read your network hardware vendor's guides for more information on managing networking.
10.1. Determine Network Requirements
It is possible to deploy a Red Hat Enterprise Virtualization environment with no consideration given to networking at all. Simply ensuring that each physical machine in the environment has at least one
82
Chapter 10. Network Setup
Network Interface Controller(NIC) cabled to a switch and assigned an IP address by DHCP is enough to begin using a Red Hat Enterprise Virtualization environment. While it is true that this approach to networking will provide a functional environment, it will not provide an optimal environment. Because network usage varies by task or action, grouping related tasks or functions into specialized networks can improve performance while simplifying the troubleshooting of network issues. By default, the Red Hat
Enterprise Virtualization Manager creates one logical network called rhevm and uses this logical network for all traffic.
The rhevm network is created and labeled as the Management logical network. The rhevm logical network is intended for management traffic between the Red Hat Enterprise Virtualization Manager and virtualization hosts. Other types of traffic that are common to all Red Hat Enterprise Virtualization environments are:
Display related traffic.
General virtual machine networking traffic.
Storage related traffic.
For the Red Hat Enterprise Virtualization environment to perform optimally, these types of traffic should be separated. This is easily accomplished by assigning each type of network traffic to a different logical network. Each logical network must be associated with a cabled, active network device. The network device that supports each logical network can be physical, a NIC or logical, like a bond device or virtual
NIC(VNIC).
The number of logical networks that can be defined and implemented in a Red Hat Enterprise
Virtualization environment is limited by the number of network interfaces present on the virtualization hosts in the environment. Each logical network needs at least one physical device to support it. Because a logical network must be implemented for each host in a cluster for the logical network to be operational, the number of logical networks that can be implemented in a given cluster is limited by the host in a cluster with the fewest NICs.
10.2. Logical Networks
By default the management network, called rhevm is defined for a data center. New logical networks, for example for data, storage or display can be defined by the administrator. In general, logical networks are created to isolate network traffic by functionality or virtualize a physical topology. In addition, other networks can be used to segregate virtual machine traffic from the management networks, or isolate traffic between groups of virtual machines in the same cluster. In Red Hat Enterprise Virtualization
Manager, network definition, type and function are encapsulated in a logical entity called a Logical
Network. For example, a data center may have the following networks,
Guest data network
Storage network access
Management network
Display network (for SPICE or VNC)
Warning:
Do not change networking in a data center or a cluster if any hosts are running. This may make the host unreachable.
10.2.1. Adding Logical Networks
83
Red Hat Enterprise Virtualization 3.0 Installation Guide
A logical network is assigned by an administrator as a required resource of a cluster in a data center. By extension all hosts in a cluster must have the same set of logical networks implemented. The implementation itself may vary from host to host (IP and bonding properties). Therefore, to configure a network, you need to first define the network for a data center and then apply this network to each host in a cluster. By default the management network (rhevm) is defined for a data center.
This section describes how to define a Storage logical network for a data center, apply the Storage logical network to a cluster, and implement the Storage logical network for hosts. This process can be repeated for each logical network being added to a data center.
To define logical networks in a cluster
1. Navigate to the Tree pane and click the Expand All button. Under System, click select the data center to which a new logical network will be added. On the results list, the selected data center displays.
2. On the details pane, select the Logical Networks subtab. This displays the existing logical networks. At the minimum, the default rhevm network is listed.
3. Click New. The New Logical Network dialog displays.
Figure 10.1. Add a logical network.
Fill in the Name and Description fields, and select the desired cluster from the Assign
Networks to Cluster(s) section, to automatically add the Storage network to the cluster.
4. Click OK to create the new logical network.
Result:
You have defined this network as a resource required by the a cluster in the data center. You can now add this resource to the hosts in the cluster.
To add network to hosts
1. Back on the Tree pane, click Default → Clusters → Default → Hosts. The Hosts tab displays a list of available hosts.
84
Chapter 10. Network Setup
2. For each of your installed hosts, perform the following tasks: a. Click on the host. On the details pane, select the Network Interfaces tab.
b. A list of network interfaces available for this host displays. One of them will already have the management network (rhevm) configured.
c. Select the interface on which to configure the newly added network and click the Add/Edit button. The Edit Network Interface dialog displays.
Figure 10.2. Edit network interface
Configure the following options:
Under Network, select your newly created storage network.
Select the Static or DHCP radio button. If static was selected, enter the IP and
Subnet Mask you have prepared as part of the prerequisites to this procedure.
Select the Save network configuration checkbox.
d. Click OK.
Result:
You have now added a new Storage network to your data center. On the Logical Networks tab of the Default data center, you should have at least two networks - rhevm and Storage. You can repeat this process for each logical network being added to a data center
10.2.1.1. Designate Display Network
A logical network created to carry display traffic must be designated as the Display Network using the Red Hat Enterprise Virtualization Manager administration portal.
To designate a new logical network as the display network
85
Red Hat Enterprise Virtualization 3.0 Installation Guide
1. Select the Clusters tab, and select the cluster you wish to designate a display network for.
2. Select the Logical Networks.
3. Select the logical network that you wish to designate as the Display network.
4. Click the Set as Display button.
5. Update Display Network displays in the Events tab.
Result:
You have successfully designated a logical network as the display network.
10.3. Set Up a Bond Device
A Bond aggregates multiple NICs in a parallel manner to provide combined speed that is beyond single
NIC speeds. Bonding provides increased fault tolerance by increasing the number of failures required for networking to fail completely. The NICs that form a bond device must be of the same make and model in order to ensure that both devices support the same options and modes.
The packet dispersal algorithm for a bond is determined by the bonding mode used.
Bonding Modes
Red Hat Enterprise Virtualization supports the following common bonding modes:
(Mode 1) Active-backup policy sets all interfaces to the backup state while one remains active. Upon failure on the active interface, a backup interface replaces it as the only active interface in the bond.
The MAC address of the bond in mode 1 is visible on only one port (the network adapter), to prevent confusion for the switch. Mode 1 provides fault tolerance and is supported in Red Hat Enterprise
Virtualization.
(Mode 2) XOR policy selects an interface to transmit packages to based on the result of a XOR operation on the source and destination MAC addresses multiplied by the modulo slave count. This calculation ensures that the same interface is selected for each destination MAC address used.
Mode 2 provides fault tolerance and load balancing and is supported in Red Hat Enterprise
Virtualization.
(Mode 4) IEEE 802.3ad policy creates aggregation groups for which included interfaces share the speed and duplex settings. Mode 4 uses all interfaces in the active aggregation group in accordance with the IEEE 802.3ad specification and is supported in Red Hat Enterprise Virtualization.
(Mode 5) Adaptive transmit load balancing policy ensures the outgoing traffic distribution is according to the load on each interface and that the current interface receives all incoming traffic. If the interface assigned to receive traffic fails, another interface is assigned the receiving role instead. Mode 5 is supported in Red Hat Enterprise Virtualization.
To create a bond device using the Red Hat Enterprise Virtualization Manager administration portal
1. Click the Hosts tab.
2. Select the host for which a bond device will be created.
3. Click the Network Interfaces tab in the details pane.
4. Select the devices that will be included in the bond, ensuring they are all of the same make and model.
86
Figure 10.3. Bond Network Devices.
5. Click the Bond button. The Bond Network Interfaces dialog displays.
Chapter 10. Network Setup
Figure 10.4 . Bond Devices Dialogue.
Enter the configuration information for the new bond device including:
Bond Name: select one from the drop down list.
Network: the logical network that the bond device will be a part of.
Bonding mode: the bonding mode that provides the desired functionality.
IP address assignment mechanism: either DHCP or Static. If static, then IP, Subnet Mask, and
Default Gateway must all be set manually.
Check connectivity: ensure that the bond device is functional upon creation.
Save Network Configuration: make the bond device persistent through reboots.
6. Click the OK. The Events tab displays Bond device created.
87
Red Hat Enterprise Virtualization 3.0 Installation Guide
Result:
A bond device is listed in the Network Interfaces tab of the details pain for the selected host
To enable bonding on a switch
Bonding must be enabled for the ports that the host uses on the switch it is connected to. The process by which bonding is enabled is slightly different for each switch, consult the manual provided by your switch vendor for detailed information on how to enable bonding.
The following is an bond example configuration for a switch. Your switch configuration may look different.
interface Port-channel11
switchport access vlan 153
switchport mode access
spanning-tree portfast disable
spanning-tree bpduguard disable
spanning-tree guard root
interface GigabitEthernet0/16
switchport access vlan 153
switchport mode access
channel-group 11 mode active
interface GigabitEthernet0/17
switchport access vlan 153
switchport mode access
Important
For every type of switch it is important to set up the switch bonding with the Link Aggregation
Control Protocol(LACP) protocol and not the Cisco Port Aggregation Protocol(PAgP) protocol.
88
Chapter 11. Storage Setup
Chapter 11. Storage Setup
This chapter provides instruction on configuring, and attaching storage to the Red Hat Enterprise
Virtualization environment. For information about managing storage, including maintenance and removal, refer to the Red Hat Enterprise Virtualization Administration Guide.
Red Hat Enterprise Virtualization uses a centralized storage system for virtual machine disk images, ISO files and snapshots. Storage networking can be implemented using Network File System (NFS), Internet
Small Computer System Interface (iSCSI), Fibre Channel Protocol (FCP), or local storage attached directly to the virtualization hosts. This section describes how to set up and manage the variety of storage types that can be used in the Red Hat Enterprise Virtualization platform. Setting up storage is a vital prerequisite for a new data center because a data center cannot be initialized unless storage domains are attached and activated.
A Red Hat Enterprise Virtualization system administrator needs to create, configure, attach and maintain storage for the virtualized enterprise. A familiarity with the storage types and their use is highly recommended. This document does not describe the concepts, protocols, requirements or general usage of NFS, iSCSI, FCP, or local storage. It is recommended that you read your storage array vendor's guides, and refer to Red Hat Enterprise Linux — Storage Administration Guide for more information on managing storage, if necessary.
The Red Hat Enterprise Virtualization platform enables administrators to assign and manage storage effectively and efficiently. The Storage tab on the Red Hat Enterprise Virtualization platform provides
89
Red Hat Enterprise Virtualization 3.0 Installation Guide an efficient graphical way to view and manage networked storage. The Storage Results list displays all the storage domains, and the Details pane enables access to general information about the domain.
Red Hat Enterprise Virtualization platform has three types of storage domains:
Data domains hold the disk images of all the virtual machines running in the system, operating system images and data disks. In addition, snapshots of the virtual machines are also stored in the data domain. The data cannot be shared across data centers, and the data domain must be of the same type as the data center. For example, a data center of a iSCSI type, must have an iSCSI data domain. A data domain cannot be shared between data centers.
Additionally you must attach a data domain to a data center before you will be allowed to attach domains of other types to it.
ISO domains store ISO files (or logical CDs) used to install and boot operating systems and applications for the virtual machines. Because an ISO domain is a logical entity replacing a library of physical CDs or DVDs, an ISO domain removes the data center's need for physical media. An ISO domain can be shared across different data centers. ISO storage domains must be located on NFS storage.
An export domain is a temporary storage repository that is used to copy/move images between data centers and Red Hat Enterprise Virtualization Manager installations. In addition, the export domain can be used to backup virtual machines. An export domain can be moved between data centers, however, it can only be active in one data center at a time. Support for export storage domains backed by mechanisms other than NFS is being deprecated. New export storage domains must be created on NFS storage.
Once you have determined the storage needs of your data center(s) you must begin configuring and attaching the storage:
To configure, and attach NFS storage, see Section 11.1.1, “Adding NFS Storage”
.
To configure, and attach iSCSI storage, see Section 11.1.2, “Adding iSCSI Storage”
.
To configure, and attach FCP storage, see Section 11.1.3, “Adding FCP Storage”
.
To configure, and attach local storage, see Section 11.1.4, “Adding Local Storage”
.
Important — Before Adding Storage
Before adding storage ensure that you have a working Red Hat Enterprise Virtualization Manager environment. You must be able to successfully access the Administration Portal, and there must be at least one host connected with a status of Up.
Important — Export Domain Storage Type
Support for export storage domains backed by storage on anything other than NFS is being deprecated. While existing export storage domains imported from Red Hat Enterprise
Virtualization 2.2 environments remain supported new export storage domains must be created on NFS storage.
11.1. Storage Domains Overview
11.1.1. Adding NFS Storage
90
Chapter 11. Storage Setup
An NFS storage domain is an NFS file share that is attached to a data center. Once you attach an NFS file share to the data center as a storage domain it is used to provide storage to the Red Hat Enterprise
Virtualization environment. How the storage domain is used depends on the function you select when attaching it.
This section details how to prepare NFS file shares on your storage infrastructure and attach them using the Red Hat Enterprise Virtualization Manager. For further information on NFS itself, see the Red
Hat Enterprise Linux — Storage Administration Guide
Figure 11.1. Add NFS
Important — NFSv4 is not Natively Supported
NFSv4 is not natively supported by Red Hat Enterprise Virtualization. Red Hat Enterprise
Virtualization will always attempt to mount NFS storage using NFSv3.
Your NFS storage server must support NFSv3 to be used with Red Hat Enterprise Virtualization.
Attempts to attach NFS storage which has been exported from servers that do not support NFSv3 to the Red Hat Enterprise Virtualization environment will fail.
Preparing NFS Storage
This section outlines how to prepare an NFS file share on a server running Red Hat Enterprise Linux 6.
Once created the NFS share can be attached by the Red Hat Enterprise Virtualization Manager.
1. Install nfs-utils
NFS functionality is provided by the nfs-utils package. Before file shares can be created, check that the package is installed by querying the RPM database for the system:
$ rpm -qi nfs-utils
If the nfs-utils package is installed then the package information will be displayed. If no output is displayed then the package is not currently installed. Install it using yum while logged in as the
root user:
# yum install nfs-utils
2. Configure Boot Scripts
91
92
Red Hat Enterprise Virtualization 3.0 Installation Guide
To ensure that NFS shares are always available when the system is operational both the nfs and
rpcbind services must start at boot time. Use the chkconfig command while logged in as
root to modify the boot scripts.
# chkconfig --add rpcbind
# chkconfig --add nfs
# chkconfig rpcbind on
# chkconfig nfs on
Once the boot script configuration has been done, start the services for the first time.
# service rpcbind start
# service nfs start
3. Create Directory
Create the directory you wish to share using NFS.
# mkdir /exports/iso
Replace /exports/iso with the name, and path of the directory you wish to use.
4. Export Directory
To be accessible over the network using NFS the directory must be exported. NFS exports are controlled using the /etc/exports configuration file. Each export path appears on a separate line followed by a tab character and any additional NFS options. Exports to be attached to the Red
Hat Enterprise Virtualization Manager must have the read, and write, options set.
To grant read, and write access to /exports/iso using NFS for example you add the following line to the /etc/exports file.
/exports/iso *(rw)
Again, replace /exports/iso with the name, and path of the directory you wish to use.
5. Reload NFS Configuration
For the changes to the /etc/exports file to take effect the service must be told to reload the configuration. To force the service to reload the configuration run the following command as root:
# service nfs reload
6. Set Permissions
The NFS export directory must be configured for read write access and must be owned by vdsm:kvm. If these users do not exist on your external NFS server use the following command, assuming that /exports/iso is the directory to be used as an NFS share.
# chown -R 36:36 /exports/iso
The permissions on the directory must be set to allow read and write access to both the owner and the group. The owner should also have execute access to the directory. The permissions are set using the chmod command. The following command arguments set the required permissions on the /exports/iso directory.
# chmod 0755 /exports/iso
Chapter 11. Storage Setup
Result:
The NFS file share has been created, and is ready to be attached by the Red Hat Enterprise
Virtualization Manager.
Attaching NFS Storage
An NFS type Storage Domain is a mounted NFS share that is attached to a data center. It is used to provide storage for virtualized guest images and ISO boot media. Once NFS storage has been exported it must be attached to the Red Hat Enterprise Virtualization Manager, using the Administration Portal.
To add an NFS data, or export, storage domain you must select an NFS data center. NFS storage domains for ISO storage are able to be added to data centers of any type.
1. Click the Storage tab. The Storage list and toolbar display.
2. Click New Domain.
3. The New Storage dialog box displays.
Figure 11.2. NFS Storage
4. Configure the following options:
Nam e: Enter a suitably descriptive name.
Data Center: Select the required Data Center from the drop-down list.
Dom ain Function/ Storage T ype: In the drop down menu, select Data → NFS. The storage domain types which are not compatible with the Default data center are grayed out.
After you select your domain type, the Export Path field appears.
Export path: Enter the IP address or a resolvable hostname of the chosen host. The export path should be in the format of 192.168.0.10:/Images/ISO or
dom ain.exam ple.com :/Im ages/ISO
Use Host: Select any of the hosts from the drop down menu. Only hosts which belong in the pre-selected data center will display in this list.
93
Red Hat Enterprise Virtualization 3.0 Installation Guide
Active Host Required
All communication to the storage domain is via the selected host and not directly from the
Red Hat Enterprise Virtualization Manager. At least one active host must exist in the system, and be attached to the chosen data center, before the storage is configured.
5. Click OK.
Result:
The new NFS data domain displays on the Storage tab. It will remain with a Locked status while it is being prepared for use. When ready, it is automatically attached to the data center.
11.1.2. Adding iSCSI Storage
Red Hat Enterprise Virtualization platform supports iSCSI storage via the creation of a Storage
Dom ain for a Volum e Group. A Volum e Group is a set of pre-defined Logical Unit Numbers (LUNs).
Red Hat Enterprise Virtualization supports creation of a Storage Domain from a pre-existent Volume
Group or a set of LUNs. Neither Volum e Groups nor LUNs are able to be attached to more than one
Storage Dom ain at a time.
For information regarding the setup and configuration of iSCSI on Red Hat Enterprise Linux, see the Red
Hat Enterprise Linux — Storage Administration Guide.
1. On the tree pane, select the Tree tab. On System, click the + icon to display the available data centers.
2. Select the Data Center to which the domain is to be added. The storage type of the data center selected determines the type of storage domains that can be added to it. To add an iSCSI data, or export, storage domain you must select an iSCSI data center. iSCSI storage domains can not be used for ISO storage domains.
3. Click the New Domain button.
4. Click New Storage. The New Storage dialog box displays.
5. From the Domain Function / Storage Type drop-down menu, select the appropriate storage type for the storage domain. The storage domain types that are not compatible with the chosen data center are not available.
6. Select an active host in the Use host field. To attach a domain, the name of an active host must be selected from the list of existing hosts. Only hosts that are attached to the selected Data
Center are listed.
Active Host Required
All communication to the storage domain is via the selected host and not directly from the
Red Hat Enterprise Virtualization Manager. At least one active host must exist in the system, and be attached to the chosen data center, before the storage is configured.
7. The Red Hat Enterprise Virtualization Manager is able to map either iSCSI targets to LUNs, or
LUNs to iSCSI targets. The New Domain dialog automatically displays known targets with unused
LUNs when iSCSI is selected as the storage type. If the target that you are adding storage from is not listed then you can use target discovery to find it, otherwise proceed to the next step.
94
Chapter 11. Storage Setup
Figure 11.3. New Domain Dialog iSCSI Target Discovery
Click Discover Targets to enable target discovery options. The New Domain dialog automatically displays targets with unused LUNs when iSCSI is selected as the storage type. If the target that you are adding is not listed, click Discover Targets to enable target discovery options.
Enter the fully qualified domain name or IP address of the iSCSI host in the Address field.
Enter the port to connect to the host on when browsing for targets in the Port field. The default is 3260.
If the Challenge Handshake Authentication Protocol (CHAP) is being used to secure the storage, select the User Authentication check box. Enter the CHAP user name and password.
Click the Discover button.
8. Click the + button next to the desired target. This will expand the entry and display all unused
LUNs attached to the target.
95
Red Hat Enterprise Virtualization 3.0 Installation Guide
Figure 11.4 . iSCSI LUN Selection
9. Select the check box for each LUN that you are using to create the storage domain.
10. Click OK to create the storage domain.
Result:
The new iSCSI storage domain displays on the storage tab. This will take some time.
11.1.2.1. Mapping iSCSI Targets to LUNs
Follow the below mentioned procedure:
1. Click the + button next to the desired target.
2. Select the check box for each LUN that you are using to create the storage domain.
3. Click OK.
Result:
The new storage domain is created.
11.1.3. Adding FCP Storage
Red Hat Enterprise Virtualization platform supports SAN storage via the creation of a Storage
96
Chapter 11. Storage Setup
Dom ain for a Volum e Group. A Volum e Group is a set of pre-defined Logical Unit Numbers (LUNs).
Red Hat Enterprise Virtualization supports creation of a Storage Domain from a pre-defined Volume
Group or a set of LUNs. Neither Volum e Groups nor LUNs are able to be attached to more than one
Storage Dom ain at a time.
Red Hat Enterprise Virtualization system administrators need a working knowledge of Storage Area
Networks (SAN) concepts. SAN usually uses Fibre Channel Protocol (FCP) for traffic between hosts and shared external storage. For this reason, SAN may occasionally be referred to as FCP storage.
For information regarding the setup and configuration of FCP or multipathing on Red Hat Enterprise
Linux, please refer to the Storage Administration Guide and DM Multipath Guide.
Procedure 11.1. To Add FCP Storage:
1. Click the Storage tab. The Storage list and toolbar display.
2. Click New Domain.
3. The New Domain dialog box displays.
Figure 11.5. Adding FCP Storage
4. Configure the following options: a. Name: Enter a suitably descriptive name.
b. Data Center: Select the required Data Center from the drop-down list.
c. Domain Function/ Storage Type: Select FCP.
d. Use Host: Select the IP address of either the hypervisor or Red Hat Enterprise Linux host.
Active Host Required
All communication to the storage domain is via the selected host and not directly from the Red Hat Enterprise Virtualization Manager. At least one active host must exist in the system, and be attached to the chosen data center, before the storage is configured.
97
Red Hat Enterprise Virtualization 3.0 Installation Guide e. The list of existing LUNs display. On the selected LUN, select the Add LUN check box to use it as the FCP data domain.
5. Click OK.
Result:
The new FCP data domain displays on the Storage tab. It will remain with a Locked status while it is being prepared for use. When ready, it is automatically attached to the data center. Select either Build
New Dom ain or Use Existing Volum e Group.
11.1.4. Adding Local Storage
A local storage domain can be set up on a host, to be used as a data domain for a data center and cluster that contains only a single host. Virtual machines created in a single host cluster cannot be migrated, fenced or scheduled.
Preparing Local Storage
This section outlines how to set up a local directory with recommended settings.
On a Red Hat Enterprise Virtualization Hypervisor host, set up the path for the local storage as
/data/im ages. This is the only path permitted for a Red Hat Enterprise Virtualization Hypervisor.
On a Red Hat Enterprise Linux host other paths are supported but the directories to support it must be manually created first.
The path must have permissions allowing read and write access to the vdsm user and kvm group.
These permissions are set automatically on the /data/images path for Red Hat Enterprise
Virtualization Hypervisor hosts. you must set them manually on paths to be used for local storage on
Red Hat Enterprise Linux hosts.
# chown 36:36 /data /data/images
# chmod 0755 /data /data/images
On a Red Hat Enterprise Linux host, set up the path for local storage in the /data directory. Any path is permitted on a Red Hat Enterprise Linux host. Follow these instructions to add local storage:
1. On the tree pane, select the Tree tab. On System, click the + icon to display the available data centers.
2. Select the Data Center to which the domain is to be added. The storage type of the data center selected determines the type of storage domains that can be added to it. To add a local data storage domain you must select a local data center.
3. Click New Domain. The New Domain dialog box displays.
4. Enter the Name of the domain. A descriptive name is recommended.
5. Select the Data / Local on Host option as the Domain Function / Storage Type for the storage domain.
6. Select the local host in the Use host field. This must be the host on which the local storage is set up.
Important — Active Host Required
All communication to the storage domain is via the selected host and not directly from the Red Hat Enterprise Virtualization Manager. At least one active host must exist in the system, and be attached to the chosen data center, before the storage is configured.
98
Chapter 11. Storage Setup
7. Enter the Path of the storage. For example, /data/images.
8. Click OK.
Result:
The new local storage domain displays on the Storage tab. This may take a few moments.
11.2. Populate the ISO Domain
Once an ISO storage domain is defined for a data center, CD-ROM images or ISO images must be uploaded for the virtual machines to use. Red Hat Enterprise Virtualization provides an ISO uploader tool that ensures that the images are uploaded into the correct directory path, with the correct user
permissions. While an example is provided here, for full usage information see Section C.3, “ISO
The creation of ISO images from physical media is not described in this document. It is assumed that you have access to the images required for your environment.
1. Copy the required ISO image to a temporary directory on the system running Red Hat Enterprise
Virtualization Manager.
2. Log in to the system running Red Hat Enterprise Virtualization Manager as the root user.
3. Use the rhevm-iso-uploader command to upload the ISO image. This action will take some time, the amount of time varies depending on the size of the image being uploaded and available network bandwidth.
Example 11.1. ISO Uploader Usage
In this example the ISO image RHEL6.iso is uploaded to the ISO domain called ISODomain using NFS. The command will prompt for an administrative username and password. The username must be provided in the form username@domain.
# rhevm-iso-uploader --iso-domain=ISODomain upload RHEL6.iso
Result:
The ISO image is uploaded and appears in the ISO storage domain specified. It is also available in the list of available boot media when creating virtual machines in the data center which the storage domain is attached to.
11.2.1. Uploading the VirtIO and Guest Tool Image Files
When a local ISO storage domain is configured during installation the virtio-win ISO and Virtual Floppy
Drive (VFD) images, containing the VirtIO drivers for Windows virtual machines, are automatically copied to the new storage domain. The rhev-tools-setup ISO, containing the Red Hat Enterprise Virtualization
Guest Tools for Windows virtual machines are also copied to the domain.
These image files provide software that can be installed on guest operating systems to improve the performance and usability of the virtual machine. The most recent virtio-win and rhev-tools-setup images are referred to by the following symbolic links on the filesystem of the Red Hat Enterprise Virtualization
Manager:
/usr/share/virtio-win/virtio-win.iso
/usr/share/virtio-win/virtio-win.vfd
99
Red Hat Enterprise Virtualization 3.0 Installation Guide
/usr/share/rhev-guest-tools-iso/rhev-tools-setup.iso
These image files must be manually uploaded to ISO storage domains that were not created locally by the installation process. You must use the rhevm-iso-uploader command to upload these images to your ISO storage domain. Once the image files have been uploaded they can be attached to, and used by, virtual machines.
Example 11.2. Upload of VirtIO and Guest Tool Image Files
In this example the virtio-win.iso, virtio-win.vfd, and rhev-tools-setup.iso image files are uploaded to the ISODomain ISO storage domain.
# rhevm-iso-uploader --iso-domain=ISODomain upload /usr/share/virtio-
win/virtio-win.iso /usr/share/virtio-win/virtio-win.vfd /usr/share/rhev-
guest-tools-iso/rhev-tools-setup.iso
100
Part V. Appendices
Part V. Appendices
101
Red Hat Enterprise Virtualization 3.0 Installation Guide
Troubleshooting and Error Messages
A.1. Red Hat Enterprise Virtualization Manager Log Files
Table A.1. Installation
Log File
/var/log/rhevm /rhevm setup-yyyy_mm_dd_hh_mm.log
/var/log/rhevm /rhevm upgrade-yyyy_mm_dd_hh_mm_ss.log
/var/log/rhevm /rhevm -dwh/rhevm -dwhsetup-yyyy_mm_dd_hh_mm_ss.log
/var/log/rhevm /rhevm -reports/rhevm reports-setup-yyyy_mm_dd_hh_mm_ss.log
Description
Log from the rhevm-setup command. A log is generated each time the command is run. The date and time of the run is used in the filename to allow multiple logs to exist concurrently.
Log from the rhevm-upgrade command. A log is generated each time the command is run. The date and time of the run is used in the filename to allow multiple logs to exist concurrently.
Log from the rhevm-dwh-setup command. This is the command used to create the
rhevm _history database for reporting. A log is generated each time the command is run. The date and time of the run is used in the filename to allow multiple logs to exist concurrently.
Log from the rhevm-reports-setup command.
This is the command used to install the Red Hat
Enterprise Virtualization Manager Reports modules. A log is generated each time the command is run. The date and time of the run is used in the filename to allow multiple logs to exist concurrently.
Table A.2. Service Activity
Log File
/var/log/rhevm /rhevm .log
Description
Reflects all Red Hat Enterprise Virtualization
Manager GUI crashes, Active Directory look-ups,
Database issues, and other events.
Table A.3. Client
Log File
%TEMP%/manager_hostname/log
Description
Client side log of messages output by the
Administration Portal WPF applet.
A.2. Context Sensitive Help
The Administration Portal features context sensitive help links on a number of dialog boxes. It is intended that these links will take you directly to the section of the documentation which is relevant to the task you are performing.
102
Troubleshooting and Error Messages
Dialog boxes that are linked to a topic in the documentation display a ? icon in the top right hand corner of the screen. Clicking this icon opens the relevant section of the documentation.
Figure A.1. Example of a Dialog Box with Context Sensitive Help
A.2.1. Administration Portal
If a link on the Administration Portal brought you directly to this section of the documentation then the content for the dialog box you are using has not been updated for this release yet.
103
Red Hat Enterprise Virtualization 3.0 Installation Guide
Directory Services
Red Hat Enterprise Virtualization Manager is able to use both Active Directory and IPA Server for user authentication. This appendix documents the basic requirements for directory servers of either type to be added to the environment.
Information on adding or removing directory services domains to the Red Hat Enterprise Virtualization
Manager configuration, once they have been created, is available in Section C.1, “Domain Management
B.1. IPA Server
IPA is an integrated security information management solution which combines Red Hat Enterprise Linux,
Red Hat Directory Server, MIT Kerberos, and NTP. It provides web browser and command-line interfaces, and its numerous administration tools allow an administrator to quickly install, set up, and administer one or more servers for centralized authentication and identity management.
The latest version of IPA extends the integration of DNS, includes a Certificate System Server, an enhanced administrative framework, support for host identities, netgroups, automount by location and other features.
Installation
IPA focuses on making centralized identity and policy easy to manage in Linux and Unix environments, and includes compatibility with Windows environments. If you need assistance installing or configuring
IPA, see the Red Hat Enterprise Linux — Enterprise Identity Management Guide.
B.1.1. Adding New Users
Because this section is devoted to getting you started with IPA quickly and easily, we have included only a limited number of examples. In this case, we have used the example of adding a new user to the system as an introduction to administering your IPA system. The methods and general approach, however, apply to nearly all IPA objects (users, groups, hosts, etc.), upon which you would perform some operation, such as add, show, find, or delete. The general syntax involved follows the same pattern: ipa
object-operation
Use the # ipa user-add command to create IPA users. Numerous options are available to customize the way your IPA users are created. Use the ipa help user command to access the available help on operations regarding user creation. Password management can be performed as a separate operation or as part of the initial user creation process. This, and other aspects of creating IPA users, are discussed below.
Interactive Mode
In interactive mode, the user is first created and their password created separately so that they can authenticate and log in. Use the # ipa user-add command to create an IPA user. You can run this command with or without additional parameters. If you omit any of the required parameters, the interface will prompt you for the information.
The following example demonstrates adding a new user to IPA. In this example, the ipa user-add command was executed without any additional parameters; all required information was entered in interactive mode.
104
Directory Services
# ipa user-add
First name: Ryan
Last name: Andrews
User login [randrews]:
---------------------
Added user "randrews"
---------------------
User login: randrews
First name: Ryan
Last name: Andrews
Full name: Ryan Andrews
Display name: Ryan Andrews
Initials: RA
Home directory: /home/randrews
GECOS field: randrews
Login shell: /bin/sh
Kerberos principal: [email protected]
UID: 1316000004
Type ipa passwd <user login> to create a password for the user. This is a temporary password, or
one-time password (OTP), and the user is required to change it the first time they log in. This is done intentionally, so that an administrator can reset a password for a user but they are unable to take advantage of that knowledge, because the user must change the password when they first log in.
Unattended Mode
As an integrated (or unattended) operation, you can pass the --password option to the ipa user-add command. This will force the command to prompt for an initial password. As an alternative, echo the password directly into the command:
# echo "secret123" | ipa user-add asmart --first=Alex --last=Smart --password
--------------------
Added user "asmart"
--------------------
User login: asmart
First name: Alex
Last name: Smart
Full name: Alex Smart
Display name: Alex Smart
Initials: AS
Home directory: /home/asmart
GECOS field: asmart
Login shell: /bin/sh
Kerberos principal: [email protected]
UID: 1315400003
Performing Initial Login
You can now authenticate using the newly-created user and temporary password. Type kinit <user
login> to log in to IPA. This will prompt you for a password and then immediately request a password change.
You can browse the IPA man pages and help system to explore other IPA commands. Please take some time to become familiar with the ways other IPA objects can be created and modified.
B.2. Active Directory
105
Red Hat Enterprise Virtualization 3.0 Installation Guide
This section is intended to provide a brief overview of the Active Directory configuration required to support the directory services requirements of Red Hat Enterprise Virtualization. It is not to be considered as a complete guide to the use of Active Directory. For full configuration procedures, refer to the appropriate Microsoft documentation available at http://technet.microsoft.com/enus/library/dd578336(WS.10).aspx
.
Installation
Active Directory Domain Services must be installed and available prior to commencement of the Red
Hat Enterprise Virtualization Manager installation. For Active Directory Domain Services installation instructions, including the creation of a new Forest and associated Domain, refer to the Microsoft documentation at: http://technet.microsoft.com/en-au/library/cc772464(WS.10).aspx
.
Users
The Red Hat Enterprise Virtualization administrative user must be created prior to installation. The credentials of this user are required to complete Red Hat Enterprise Virtualization Manager installation. It is the account used when logging into the Red Hat Enterprise Virtualization Administration Portal to manage the system.
The Red Hat Enterprise Virtualization administrative user must have delegated control over the Domain to:
Join a com puter to the dom ain.
Modify the m em bership of a group.
For information on creation of user accounts refer to http://technet.microsoft.com/enus/library/cc732336.aspx
.
For information on delegation of control refer to http://technet.microsoft.com/en-us/library/cc732524.aspx
.
Important — Do not use the Administrator user
An Active Directory user account must be created specifically for use as the Red Hat Enterprise
Virtualization administrative user. Do not use the Active Directory Administrator account as the Red Hat Enterprise Virtualization Manager administrative user.
106
Additional Utilities
Additional Utilities
C.1. Domain Management Tool
Red Hat Enterprise Virtualization Manager uses directory services to authenticate users. While during installation the manager sets up a domain named internal this is only used for the admin user. To add and remove other users from the system it is first necessary to add the directory service(s) in which they are found.
The supported directory services are Active Directory and IPA. Red Hat Enterprise Virtualization
Manager includes a domain management tool, rhevm-manage-domains, to add and remove domains provided by these services. In this way it is possible to grant access to the Red Hat Enterprise
Virtualization environment to users stored across multiple domains. This is true even where some users are stored in a domain managed by Active Directory and others are stored in a domain managed by IPA.
You will find the rhevm-manage-domains command on the machine to which Red Hat Enterprise
Virtualization Manager was installed. The rhevm-manage-domains command must be run as the
root user.
C.1.1. Syntax
The usage syntax is:
Usage: rhevm-manage-domains -action=ACTION [options]
Available actions are:
add
Add a domain to the manager's directory services configuration.
edit
Edit a domain in the manager's directory services configuration.
delete
Delete a domain from the manager's directory services configuration.
validate
Validate the manager's directory services configuration. The command attempts to authenticate to each domain in the configuration using the configured username and password.
list
List the manager's current directory services configuration.
The options available to be combined with the actions on the command line are:
-domain=DOMAIN
Specifies the domain the action must be performed on. The -domain parameter is mandatory for add, edit, and delete.
107
Red Hat Enterprise Virtualization 3.0 Installation Guide
-user=USER
Specifies the domain user to use. The -user parameter is mandatory for add, and optional for
edit.
-interactive
Specifies that the domain user's password is to be provided interactively. This option, or the -
passwordFile option, must be used to provide the password for use with the add action.
-passwordFile=FILE
Specifies that the domain user's password is on the first line of the provided file. This option, or the -interactive option, must be used to provide the password for use with the add action.
-configFile=FILE
Specifies an alternative configuration file that the command must load. The -configFile parameter is always optional.
-report
Specifies that when performing the validate action all validation errors encountered will be reported in full.
Common usage examples are discussed further within this guide. For full usage information consult the
rhevm -m anage-dom ains command's help output:
# rhevm-manage-domains --help
C.1.2. Examples
The following examples demonstrate the use of the rhevm-manage-domains to perform basic manipulation of the Red Hat Enterprise Virtualization Manager domain configuration.
Example C.1. Adding Domains to Configuration
This example runs the rhevm-manage-domains command to add the
directory.dem o.redhat.com domain to the Red Hat Enterprise Virtualization Manager configuration. The configuration is set to use the admin user when querying the domain with the password to be provided interactively.
# rhevm-manage-domains -action=add -domain='directory.demo.redhat.com' user='admin' -interactive loaded template kr5.conf file setting default_tkt_enctypes setting realms setting domain realm success
User guid is: 80b71bae-98a1-11e0-8f20-525400866c73
Successfully added domain directory.demo.redhat.com
108
Additional Utilities
Example C.2. Edit Domain in Configuration
This example runs the rhevm-manage-domains command to edit the
directory.dem o.redhat.com domain in the Red Hat Enterprise Virtualization Manager configuration. The configuration is updated to use the admin user when querying this domain with the password to be provided interactively.
# rhevm-manage-domains -action=edit -domain=directory.demo.redhat.com user=admin -interactive loaded template kr5.conf file setting default_tkt_enctypes setting realms setting domain realmo success
User guid is: 80b71bae-98a1-11e0-8f20-525400866c73
Successfully edited domain directory.demo.redhat.com
Example C.3. Deleting Domains from Configuration
This example runs the rhevm-manage-domains command to remove the
directory.dem o.redhat.com domain from the Red Hat Enterprise Virtualization Manager configuration. Users defined in the removed domain will no longer be able to authenticate with Red
Hat Enterprise Virtualization Manager. The entries for the affected users will remain defined in Red
Hat Enterprise Virtualization Manager until they are explicitly removed.
The domain being removed in this example is the last one listed in the Red Hat Enterprise
Virtualization Manager configuration. A warning is displayed highlighting this fact and that only the
adm in user from the internal domain will be able to log in until another domain is added.
# rhevm-manage-domains -action=delete -domain='directory.demo.redhat.com'
WARNING: Domain directory.demo.redhat.com is the last domain in the configuration. After deleting it you will have to either add another domain, or to use the internal admin user in order to login.
Successfully deleted domain directory.demo.redhat.com. Please remove all users and groups of this domain using the Administration portal or the API.
Example C.4 . Validating Configuration
This example runs the rhevm-manage-domains command to validate the Red Hat Enterprise
Virtualization Manager configuration. The command attempts to log into each listed domain with the credentials provided in the configuration. If the attempt is successful then the domain is reported as valid.
# rhevm-manage-domains -action=validate
User guid is: 80b71bae-98a1-11e0-8f20-525400866c73
Domain directory.demo.redhat.com is valid.
109
Red Hat Enterprise Virtualization 3.0 Installation Guide
Example C.5. Listing Domains in Configuration
This example runs the rhevm-manage-domains command to list the domains defined in the Red
Hat Enterprise Virtualization Manager configuration. For each configuration entry the command displays the domain, the username — in User Principle Name (UPN) format, and whether the domain is local or remote.
# rhevm-manage-domains -action=list
Domain: directory.demo.redhat.com
User name: [email protected]
This domain is a remote domain.
C.2. Configuration Tool
During installation, only a subset of Red Hat Enterprise Virtualization Manager's configuration settings are modified from their defaults. You make further changes with the included configuration tool, rhevm-
config.
The configuration tool does not require JBoss or Red Hat Enterprise Virtualization Manager to be running to update the configuration. Configuration key values are stored in the database and as such it must be operational for configuration changes to be saved. Changes are only applied once JBoss is restarted.
The manager's configuration is stored as a series of key to value pair mappings. The configuration tool allows you to: list all available configuration keys, list all available configuration values, get the value of a specific configuration key, and set the value of a specific configuration key.
The configuration tool also allows you to maintain multiple versions of the manager's configuration.
When getting or setting the value for a configuration key the --cver parameter is used to specify which configuration version is to be used. The default configuration version is general.
C.2.1. Syntax
You will find the configuration tool on the machine to which Red Hat Enterprise Virtualization Manager was installed. Common usage examples are discussed within this guide. For full usage information consult the rhevm-config command's help output:
# rhevm-config --help
Common Tasks
List Available Configuration Keys
Use the --list parameter to list available configuration keys.
# rhevm-config --list
The tool lists each available configuration key by name. It also returns a description of each
110
Additional Utilities key's purpose.
List Available Configuration Values
Use the --all parameter to list available configuration values.
# rhevm-config --all
The tool lists each available configuration key by name as well as the current value of the key, and the configuration version.
Get Value of Configuration Key
Use the --get parameter to get the value of a specific key.
# rhevm-config --get KEY_NAME
Replace KEY_NAME with the name of the key to retrieve. The tool returns the key name, value, and the configuration version. Optionally the --cver parameter is used to specify the configuration value from which the value should be retrieved.
Set Value of Configuration Key
Use the --set parameter to set the value of a specific key. You must also set the configuration version to which the change is to apply using the --cver parameter.
# rhevm-config --set KEY_NAME=KEY_VALUE --cver=VERSION
Replace KEY_NAME with the name of the key to set, and replace KEY_VALUE with the value to assign to it. In an environment with more than one configuration version you must also take care to replace VERSION with the name of the configuration version in use.
C.2.2. Examples
Example C.6. Getting a Configuration Value
# rhevm-config --get=SearchResultsLimit --cver=general
100
Example C.7. Setting a Configuration Value
# rhevm-config --set SearchResultsLimit=50 --cver=general
C.3. ISO Uploader
The Red Hat Enterprise Virtualization Manager installation includes a tool for uploading ISO images to the ISO storage domain. This tool is referred to as the ISO uploader. It provides for the listing of storage domains and uploading of ISO files to them.
111
Red Hat Enterprise Virtualization 3.0 Installation Guide
The ISO uploader command is rhevm-iso-uploader. You must be logged in as the root user to run it successfully. You must provide the administration credentials for the Red Hat Enterprise Virtualization environment on the command line. Full usage information, including a list of all valid options for the command, is available by running the rhevm-iso-uploader -h command.
C.3.1. Syntax
The basic syntax is of the form:
Usage: rhevm-iso-uploader [options] list
rhevm-iso-uploader [options] upload [file].[file]...[file]
The two supported modes of operation are list, and upload.
The list parameter lists the available ISO storage domains. These storage domains are the valid targets for ISO uploads. By default the list is obtained from the Red Hat Enterprise Virtualization
Manager installation on the local machine.
The upload parameter uploads the selected ISO file(s) to the specified ISO storage domain. By default the transfer is performed using NFS however SSH is also available.
Basic ISO uploader usage requires that, at a minimum, the either the list or upload parameter is provided. Where upload is selected then the name of at least one local file to upload must also be provided.
The rhevm-iso-uploader command has a large number of options.
General Options
--version
Displays the version number of the command in use, and exits immediately.
-h, --help
Displays command usage information, and exits immediately.
--quiet
Sets quiet mode, reducing console output to a minimum. This is off by default.
--log-file=PATH
Sets PATH as the log file the command should use for its own log output.
--conf-file=PATH
Sets PATH as the configuration file the command should use.
-v, --verbose
Sets verbose mode, providing more console output. This is off by default.
112
-f, --force
Where the source file being uploaded has the same file name as an existing file at the destination, force the existing file to be overwritten automatically. This is off by default.
Additional Utilities
Red Hat Enterprise Virtualization Manager Options
The options in the Red Hat Enterprise Virtualization Manager configuration group are used to specify the manager authentication details and, filter log collection from one or more virtualization hosts. If no options in this group are specified, data is not collected from any virtualization host.
-u USER, --user=USER
Sets the user as USER. This must be a user that exists in directory services, and is known to the Red Hat Enterprise Virtualization Manager. The user must be specified in the format
user@domain, where user replaced by the username, and domain is replaced by the directory services domain in use.
-r FQDN, --rhevm=FQDN
Sets the Red Hat Enterprise Virtualization Manager to connect to as FQDN. FQDN must be replaced by the fully qualified domain name of the manager. By default it is assumed that the
ISO uploader is being run on the same machine as the manager. Therefore the default value for this parameter is localhost.
ISO Storage Domain Options
The options in this configuration group are used to specify the ISO domain to which files must be uploaded
-i, --iso-domain=ISODOMAIN
Sets the storage domain named ISODOMAIN as the destination for uploads.
-n, --nfs-server=NFSSERVER
Sets the NFS path NFSSERVER as the destination for uploads. This option is an alternative to --
iso-domain, the two must not be used at the same time.
Example C.8. Specifying an NFS Server
# rhevm-iso-uploader --nfs-server=storage.demo.redhat.com:/iso/path
upload RHEL6.0.iso
Connection Options
By default the ISO uploader uses NFS to upload files. Use options within this configuration group to use
SSH file transfer instead.
--ssh-user=USER
Sets USER as the SSH username to use for the upload.
--ssh-port=PORT
Sets PORT as the port to use when connecting to SSH.
113
Red Hat Enterprise Virtualization 3.0 Installation Guide
-k KEYFILE, --key-file=KEYFILE
Sets KEYFILE as the public key to use for SSH authentication. If no key is set the program will prompt you to enter the password of the user specified instead.
C.3.2. Examples
Example C.9. Basic ISO Uploader Usage
In this example the ISO uploader is run to list the available ISO storage domains. The username is not provided on the command line so the tool instead prompts for it to be entered. Once the storage domains have been listed, an ISO file is uploaded to one of them over NFS.
# rhevm-iso-uploader list
Please provide the REST API username for RHEV-M (CTRL+D to abort):
Please provide the REST API password for RHEV-M (CTRL+D to abort):
ISO Storage Domain List:
ISODomain
# rhevm-iso-uploader --iso-domain=ISODomain upload RHEL6.iso
Please provide the REST API username for RHEV-M (CTRL+D to abort):
Please provide the REST API password for RHEV-M (CTRL+D to abort):
C.4. Log Collector
The Red Hat Enterprise Virtualization Manager installation includes a log collection tool. This allows you to easily collect relevant logs from across the Red Hat Enterprise Virtualization environment when requesting support.
The log collection command is rhevm-log-collector. You must be logged in as the root user to run it successfully. You must provide the administration credentials for the Red Hat Enterprise
Virtualization environment on the command line. Full usage information, including a list of all valid options for the command, is available by running the rhevm-log-collector -h command.
C.4.1. Syntax
The basic syntax is of the form:
Usage: rhevm-log-collector [options] list [all, clusters, datacenters]
rhevm-log-collector [options] collect
The two supported modes of operation are list, and collect.
The list parameter lists either the hosts, clusters, or data centers attached to the Red Hat
Enterprise Virtualization Manager. You are then able to filter log collection based on the listed objects.
The collect parameter performs log collection from the Red Hat Virtualization Manager. The collected logs are placed in an archive file under the /tmp/logcollector directory. The rhevm-
log-collector command outputs the specific filename that it chose to use when log collection is completed.
114
Additional Utilities
The default action taken if no parameters are provided is to list available hosts along with the data center, and cluster, to which they belong. Where necessary the log collector will prompt you to enter usernames and passwords required to retrieve logs.
The rhevm-log-collector command has a large number of options. You can use these options to further refine the scope of log collection.
General Options
--version
Displays the version number of the command in use, and exits immediately.
-h, --help
Displays command usage information, and exits immediately.
--conf-file=PATH
Sets PATH as the configuration file the tool is to use.
--local-tmp=PATH
Sets PATH as the directory to which retrieved logs are to be saved. Default is
/tm p/logcollector.
--ticket-number=TICKET
Sets TICKET as the ticket, or case number, to associate with the SOS report.
--upload=FTP_SERVER
Sets FTP_SERVER as the destination for retrieved logs to be sent using FTP. Do not use this option unless advised to by a Red Hat support representative.
--quiet
Sets quiet mode, reducing console output to a minimum. This is off by default.
--log-file=PATH
Sets PATH as the log file the command should use for its own log output. Note that this is not to be confused with the --local-tmp parameter.
-v, --verbose
Sets verbose mode, providing more console output. This is off by default.
Red Hat Enterprise Virtualization Manager Options
The options in the Red Hat Enterprise Virtualization Manager configuration group are used to specify the manager authentication details and, filter log collection from one or more virtualization hosts. Note that it is possible to combine the options used to select the virtualization hosts, for example selecting all host in clusters A and B where the name of the host matches pattern SalesHost*.
115
Red Hat Enterprise Virtualization 3.0 Installation Guide
--no-hypervisors
Sets the option to skip collection of logs from the virtualization hosts.
-u USER, --user=USER
Sets the username to log in as to USER. This must be a username that exists in directory services, and is known to the Red Hat Enterprise Virtualization Manager. The user must be specified in the format user@domain, where user is replaced by the username, and domain is replaced by the directory services domain in use.
-r FQDN, --rhevm=FQDN
Sets the Red Hat Enterprise Virtualization Manager to connect to as FQDN. FQDN must be replaced by the fully qualified domain name of the manager. By default it is assumed that the log collector is being run on the same machine as the manager. Therefore the default value for this parameter is localhost.
-c CLUSTER, --cluster CLUSTER
Collect all logs from the Red Hat Enterprise Virtualization Manager, as well as virtualization hosts in the cluster named CLUSTER. The cluster(s) for inclusion must be specified in a comma separated list of cluster names or match patterns.
-d DATACENTER, --data-center DATACENTER
Collect all logs from the Red Hat Enterprise Virtualization Manager, as well as virtualization hosts in the data center named DATACENTER. The data center(s) for inclusion must be specified as a comma separated list of data center names or match patterns.
-H HOSTS_LIST, --hosts=HOSTS_LIST
Collect all logs from the Red Hat Enterprise Virtualization Manager, as well as virtualization hosts included in HOSTS_LIST. The hosts for inclusion must be specified as a comma separated list of hostnames, fully qualified domain names, or IP addresses. Match patterns for each type of value are also valid.
SOS Report Options
The JBoss SOS plugin is always executed by log collector. To activate data collection from the JMX console the --java-home, --jboss-user, and jboss-pass parameters must also be provided.
--jboss-home=JBOSS_HOME
JBoss installation directory path. Default is /var/lib/jbossas.
--java-home=JAVA_HOME
Java installation directory path. Default is /usr/lib/jvm/java.
116
--jboss-profile=JBOSS_PROFILE
Quoted and space separated list of server profiles. This is used to limit log collection to the specified profiles. The default is 'rhevm-slimmed'.
Additional Utilities
--enable-jmx
Enable the collection of run-time metrics from Red Hat Enterprise Virtualization's JBoss JMX interface.
--jboss-user=JBOSS_USER
JBoss JMX invoker user to be used with twiddle. Default is admin.
--jboss-logsize=LOG_SIZE
Maximum size for each log file retrieved, in MB.
--jboss-stdjar=STATE
Sets collection of JAR statistics for JBoss standard JARs. Replace STATE with on, or off. The default is on.
--jboss-servjar=STATE
Sets collection of JAR statistics from any server configuration directories. Replace STATE with
on, or off. The default is on.
--jboss-twiddle=STATE
Sets collection of twiddle data on, or off. Twiddle is the JBoss tool used to collect data from the
JMX invoker. Replace STATE with on, or off. The default is on.
--jboss-appxml=XML_LIST
Quoted and space separated list of applications whose XML descriptions should be retrieved.
Default is 'all'.
SSH Configuration
--ssh-host=PORT
Sets PORT as the port to use for SSH connections with virtualization hosts.
-k KEYFILE, --key-file=KEYFILE
Sets KEYFILE as the public SSH key to be used for accessing the virtualization hosts.
--max-connections=MAX_CONNECTIONS
Sets MAX_CONNECTIONS as the maximum concurrent SSH connections for logs from virtualization hosts. The default is 10.
PostgreSQL Database Options
The log collector connects to the Red Hat Enterprise Virtualization Manager database and dumps it for inclusion in the log report if pg-pass is specified. The database username, and database name also
117
Red Hat Enterprise Virtualization 3.0 Installation Guide must be specified if they were changed from the default values during installation.
Where the database is not on the local machine set the pg-dbhost, and optionally supply a pg-host-
key, to collect remote logs. The PostgreSQL SOS plugin must be installed on the database server for remote log collection to be successful.
--no-postgresql
Disables collection of database. Database collection is performed by default.
--pg-user=USER
Sets USER as the username to use for connections with the database server. The default is
postgres.
--pg-dbname=DBNAME
Sets DBNAME as the database name to use for connections with the database server. The default is rhevm.
--pg-dbhost=DBHOST
Sets DBHOST as the hostname for the database server. The default is localhost.
--pg-host-key=KEYFILE
Sets KEYFILE as the public identity file (private key) for the database server. This value is not set by default as it is not required where the database exists on the local host.
C.4.2. Examples
118
Additional Utilities
Example C.10. Basic Log Collector Usage
In this example log collector is run to collect all logs from the Red Hat Enterprise Virtualization
Manager and the three attached hosts. Additionally the database and JBoss logs are also collected.
# rhevm-log-collector
Please provide the username for rhevm (CTRL+D to abort): [email protected]
Please provide the password for rhevm (CTRL+D to abort):
Host list (datacenter=None, cluster=None, host=None):
Data Center | Cluster | Hostname/IP Address
SalesDataCenter | SalesCluster | 192.168.122.250
EngineeringDataCenter | EngineeringCluster | 192.168.122.251
FinanceDataCenter | FinanceCluster | 192.168.122.252
# rhevm-log-collector collect
Please provide the username for rhevm (CTRL+D to abort): [email protected]
Please provide the password for rhevm (CTRL+D to abort):
About to collect information from 3 hypervisors. Continue? (Y/n): Y
INFO: Gathering information from selected hypervisors...
INFO: collecting information from 192.168.122.250
INFO: collecting information from 192.168.122.251
INFO: collecting information from 192.168.122.252
INFO: finished collecting information from 192.168.122.250
INFO: finished collecting information from 192.168.122.251
INFO: finished collecting information from 192.168.122.252
Please provide the password to dump the PostgreSQL database (CTRL+D to abort):
INFO: Gathering PostgreSQL the RHEV-M database and log files from localhost...
INFO: Gathering RHEV-M information...
Please provide the password for jboss (CTRL+D to abort):
INFO: Log files have been collected and placed in /tmp/logcollector/sosreportrhn-account-20110804121320-ce2a.tar.xz.
The MD5 for this file is 6d741b78925998caff29020df2b2ce2a and its size is
26.7M
119
Red Hat Enterprise Virtualization 3.0 Installation Guide
Revision History
Revision 5-17.4 00
Rebuild with publican 4.0.0
2013-10-31 Rüdiger Landmann
Revision 5-17 2013-09-26
BZ#1007864 - s/Red Had/Red Hat/g
Revision 5-16
Rebuild for Publican 3.0
2012-07-18
Zac Dover
Anthony Towns
Revision 5-0 Tuesday November 22 2011 Stephen Gordon
Red Hat Enterprise Virtualization General Availability
Revision 4 -0 Friday November 04 2011
Red Hat Enterprise Virtualization External Beta 4
Stephen Gordon
Stephen Gordon Revision 3-0 Thursday October 13 2011
Red Hat Enterprise Virtualization External Beta 3
Revision 3-0 Monday August 22 2011
Red Hat Enterprise Virtualization External Beta 2
Stephen Gordon
Revision 2-0 Friday August 5 2011
Red Hat Enterprise Virtualization External Beta 1
Revision 1-0
Draft
Wednesday December 15
2010
Stephen Gordon
Stephen Gordon
120
Shkarko
Lidhja publike u përditësua
Lidhja publike për bisedën tuaj është përditësuar. You may view and manage your chat links after registration here.
Lidhja publike e dokumentit
Reklamë
