advertisement
Mini Remote
INSTEON
®
Remote Control Switch
(formerly RemoteLinc 2)
Owners Manual
2342-242, 2444A3 (US)
2342-442 (EU)
2342-542 (AUS/NZ)
Page 1 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
Page 2 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
About Mini Remote
Mini Remote is the smallest and most versatile INSTEON Remote Control in the world. The 1 Scene
Controller can easily be reconfigured to give you toggle control of up to 2 scenes and/or devices. Mini
Remote can be:
- Handheld (wireless remote)
- Mounted on wall with no trim plate (wireless keypad)
- Mounted on wall in a single-gang Decorator trim plate (wireless keypad, built-in look)
- Mounted on wall in a multi-gang Decorator trim plate (add to the number of controllers in your room without hiring an electrician and/or tearing out drywall)
- Placed on a Tabletop Stand (sold separately)
- Clipped to your car’s visor with Visor Clip (sold separately)
Status LED
Paddle
Top On, Bottom Off
(1 scene mode)
Top On/Off, Bottom On/Off
(2 scene mode)
On/Off switch
Set button
Power/Recharging Jack
(Micro-USB, 5VDC)
Page 3 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
Features & Benefits
• Small, elegant design
• Super-easy setup
• Rechargeable battery included
• Discreet On and Off buttons for 1 Scene
• Can be reconfigured for 2 Scene triggers or 2 Scene On/Off toggle control
• Can be installed into a single Decora opening (requires Wall-Mount Bracket)
• Can be used as a table-top controller (requires Tabletop Stand)
• Can be used as a visor-mounted remote control for lights, garage door opener etc. (requires Visor
Clip)
• LED blinks green when Turning a Scene On and red when turning a Scene Off
• Slide switch for disabling buttons (“vacation” or “pocket” mode)
• Stuck Button Mode – saves battery life by going to sleep if button stuck down
• Beeper for setup ease
• Recharges with standard USB charger with via Micro-USB Plug (5VDC)
• Battery life exceeds 3 months
• Battery charge LED indicator built-in
• Low battery transmit warning (use with software to trigger email/text message)
• All settings stored in stable memory which is maintained even without power
• 2 year warranty
What’s in the Box?
• Mini Remote
• Rechargeable battery (pre-installed)
• Quick-Start Guide
Required Accessories
•
A micro USB cable for connecting and recharging Mini Remote via USB port on a computer or USB power adapter.
•
If the INSTEON device you intend to control does not receive RF signals
(i.e., power line only), you will need at least one dual-band INSTEON device to convert the RF signals to power line signals.
Type A to Micro-B cable
(2444B5)
Page 4 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
Optional Accessories
Wall Mount Bracket
(2444B4)
•
Wall mount your Mini Remote anywhere
•
Gang two or more together for more control
•
Can be installed adjacent to existing wired-in switches
•
Mini Remote can easily be removed for portability or recharging
•
Use with any decorator wallplate
•
Pair the Wall Mount Bracket with any decorator style wall plate (sold separately) for the perfect wireless wall switch solution.
Tabletop Stand
(Available in the 2444Bxx kit)
•
Perfect for a nightstand, kitchen counter or coffee table
Visor Clip
(Available in the 2444Bxx kit)
•
Control your home from your vehicle
•
Turn lights on when you arrive and off as you leave
USB Power Adapter
(2444B6)
•
For use with Mini Remote USB Charging
Cable and any other device that charges via USB cable
Page 5 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
Getting Started
Fully charge your Mini Remote prior to programming or anytime the unit is not responding. Mini Remote charges via a USB cable (Type A to Micro-B, sold separately). The red charging LED will turn off once the battery has been fully charged (approximately 1 hour). To turn on Mini Remote, simply slide the power switch to the on position.
Note: Mini Remote uses a subtle beeper sound to assist setup. It is recommended that you program the unit in a quiet area.
Scenes
Scene: One or more INSTEON devices which respond to an INSTEON controller. When the scene is activated (turned “on”), all devices return to the states they were at when the scene was programmed.
INSTEON scenes let you activate dramatic lighting moods at the touch of a button. For example, you can set all the lights in a scene to dim to 50% or turn certain lights on while turning others off, all with the tap of a button on any INSTEON Controller. INSTEON scenes are easy to set up, just follow the directions below.
Maximum number of scenes in Mini Remote Switch: 2 (Default is 1)
Scene Control Functions supported; On, Off, Press & hold Bright, Press & hold Dim, Double-tap Fast On and Double-tap Fast Off.
Add Mini Remote Button to a Scene as a Controller
Follow the steps below to control a scene (one or more INSTEON devices).
1) Tap the Mini Remote switch (top or bottom paddle) – if in 2 scene mode, tap the top of the paddle for scene 1 or the bottom for scene 2
2) Adjust the scene responder to the “state” you want when the scene is activated from Mini Remote
(e.g., 50%, 25% or even OFF)
3) Press & hold Mini Remote’s Set button until Mini Remote beeps
Mini Remote’s LED will blink green
4) Press & hold the responder’s Set button until it beeps (or until its LED/load flashes)
Mini Remote will double-beep and its LED will stop blinking
Responder’s LED will stop blinking (it may also double-beep)
5) Confirm that scene addition was successful by tapping on/off on your Mini Remote
The Responder will toggle between the Scene on level and off
6) If you wish to add more responders to Mini Remote, repeat steps 1-5 for each additional scene
responder (or see Add Multiple Responders to a Scene )
1
If the Responder is a multi-scene device such as a KeypadLinc, tap the Scene button you wish to control until its LED is in the desired state (on or off)
Remove Mini Remote Button from a Scene as a Controller
If you are no longer going to use an INSTEON responder that is a scene responder of Mini Remote, it is very important that you remove its scene membership. Otherwise, Mini Remote will retry every scene command repetitively, thus creating delays and shortening battery life.
Page 6 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
1) Tap the Mini Remote switch (top or bottom paddle) - if in 2 scene mode, tap the top of the paddle for scene 1 or the bottom for scene 2
The responder will respond
2) Press & hold the Mini Remote’s Set button until it beeps
Mini Remote’s LED will blink green
3) Press & hold the Mini Remote’s Set button until it beeps again
Mini Remote’s LED will blink red
4) Press & hold the Responder’s Set button until it double-beeps (or LED blinks)
Mini Remote will double-beep and its LED will stop blinking
5) Confirm that Unlinking was successful by tapping on/off on your Mini Remote
The responder will not respond
6) If you wish to remove multiple responders from Mini Remote, repeat steps 1-5 for each additional
responder (or see Remove Multiple Responders from a Scene )
Using Mini Remote
1 Scene Mode (Default)
The switch controls scene members as follows:
Paddle Tap Press & hold Double-tap
Top Turn scene on
Brighten scene members until released
Turn scene members fullbright instantly
Bottom Turn scene off
Dim scene members until released
2 Scene Toggle Mode
The top and bottom paddle will control all its scene members as follows:
Last Command Sent Tap Press & hold
Turn scene members off instantly
Double-tap
Off or Dim
On or Bright
Turn scene on
Turn scene off
Brighten scene members until released
Dim scene members until released
Turn scene members full-bright instantly
Turn scene members off instantly
2 Scene Non-Toggle Mode (Always On)
Each button will control all its scene members as follows:
Tap Press & hold Double-tap
Turn scene On
Brighten scene members until released
Turn scene members fullbright instantly
Note: Devices in scenes that respond to the scene trigger by turning off do not respond to scene dim and brighten. Devices in Scenes that only support On/Off (such as switches and relays) do not respond to scene dim and brighten.
Page 7 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
LED Behavior
Mini Remote has a two-color LED (Green & Red) which momentarily indicates whether an on or an off is being sent.
LED State
Blink Green (Once)
Meaning
On Sent
Blink Red (Once)
Blink Red (for a few seconds)
Off Sent
One or more scene members did not acknowledge (note: scene members may still have heard the scene command and adjusted their settings)
Turn Unit On/Off (Pocket Mode)
The Mini Remote features a power switch located next to the Set button. If you plan on carrying the Mini
Remote in your pocket it is recommended that you turn it off to prevent buttons from accidentally being pressed. This is also recommended if your RemoteLinc will not be in use for long periods of time.
Power Switch
(right On, left Off)
Stuck button
If a button on Mini Remote is held for more than 4 minutes, the RemoteLinc will automatically stop transmitting to preserve battery life. The Mini Remote will automatically turn back on when the button that was depressed is no longer being pressed.
Advanced Features
Add Multiple Responders to a Scene (Multi-Link)
1) Tap the Mini Remote paddle (top or bottom) – if in 2 scene mode, tap the top of the paddle for scene
1 or the bottom for scene 2
2) Press & Hold Set Button for 3 seconds - until you hear a beep
Mini Remote’s LED will blink green
3) Tap Set Button
Mini Remote’s LED will double-blink green
4) Adjust Each Responder you wish to add to scene, then Press & Hold its Set Button until Mini Remote
Double-Beeps
Mini Remote’s LED will continue to double-blink green
5) When all your devices have been added, tap Mini Remote’s Set Button
Mini Remote double-beep and its LED will turn off
Page 8 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
Remove Multiple Responders from a Scene (Multi-Unlink)
1) Tap the Mini Remote paddle (top or bottom) – if in 2 scene mode, tap the top of the paddle for scene
1 or the bottom for scene 2
2) Press & Hold Set Button for 3 seconds - until you hear a beep
Mini Remote’s LED will blink green
3) Press & Hold Set Button a 2 nd
time for 3 seconds - until you hear a beep
Mini Remote’s LED will blink red
4) Tap Set Button
Mini Remote’s LED will double-blink red
5) For each Responder you wish to remove from scene, Press & Hold its Set Button until Mini Remote double-beeps
Mini Remote’s LED will continue to double-blink red
6) When all your devices have been removed, tap Mini Remote’s Set Button
Mini Remote will double-beep and its LED will turn off
Change Paddle / Scene Configuration (e.g. Change to 2 Scene Mode)
1. Press & Hold Set Button for 3 seconds - until you hear a beep
Mini Remote’s LED will blink green
2. Press & Hold Set Button a 2 nd
time for 3 seconds - until you hear a beep
Mini Remote’s LED will blink red
3. Press & Hold Set Button a 3 rd
time for 3 seconds - until you hear a beep
Mini Remote’s LED will blink green
4. Press & Hold Set Button a 4 th
time for 3 seconds - until you hear a beep
Mini Remote’s LED will blink red
5. Tap Set Button
Mini Remote’s LED will blink red
6. Press the appropriate paddle for the desired button/scene configuration
Desired Configuration Paddle to Press
2 Scene Toggle
2 Scene Non-Toggle (Always On)
1 Scene (Default)
Bottom
Bottom twice
Top
Mini Remote will double-beep and its LED will turn off
7. To confirm the configuration, tap the bottom of the paddle several times
Mini Remote’s LED will flash as follows
Page 9 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
Flash Pattern
Red every tap
Green every tap
Alternating Green / Red
Configuration
1 Scene
2 Scene Non-Toggle (Always On)
2 Scene Toggle
Turn LED Off (or Back On)
1) Press & Hold Set Button for 3 seconds - until you hear a beep
Mini Remote’s LED will blink green
2) Press & Hold Set Button a 2 nd
time for 3 seconds - until you hear a beep
Mini Remote’s LED will blink red
3) Press & Hold Set Button a 3 rd
time for 3 seconds - until you hear a beep
Mini Remote’s LED will blink green
4) Press the appropriate area of the paddle for the desired button/scene configuration
Desired LED Mode
LED Off
Button to Press
Bottom
LED On (default) Top
Mini Remote will double-beep and its LED will turn off
Turn Beeper On During Usage (or Back Off)
1) Press & Hold Set Button for 3 seconds - until you hear a beep
Mini Remote’s LED will blink green
2) Press & Hold Set Button a 2 nd
time for 3 seconds - until you hear a beep
Mini Remote’s LED will blink red
3) Press & Hold Set Button a 3 rd
time for 3 seconds - until you hear a beep
Mini Remote’s LED will blink green
4) Tap Set Button
Mini Remote’s LED will double-blink green
5) Press the appropriate area of the paddle for the desired button/scene configuration
Desired Beeper Mode Area to Press
Off (Default) Bottom
On Top
Mini Remote will double-beep and its LED will turn off
Page 10 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
Beeper Behavior
Command
On
Off
Fast-On
Fast-Off
Begin Bright
Begin Dim
Setup Action
Method
Tap
Tap
Double-Tap
Double-Tap
Press & hold
Press & hold
Beeper Disabled
(Default)
-
-
-
-
-
-
Enter Setup Mode, Transition to next setup mode or Exit
Setup Mode
Setup successful, return to Ready Mode
Beeper
Return to Ready Mode after a longer than 3 minute timeout
Failure to add a scene responder
Exiting Stuck Button
Beeper Enabled
Single Beep
Single Beep
Single Beep
Single Beep
Single Beep
Single Beep
Single Beep
Double-Beep
Long Beep (3 seconds)
Long Beep (3 seconds)
Long Beep (3 seconds)
LED Behavior during Setup
Mini Remote has a two-color LED (Green & Red) which displays helpful information.
LED State
Blinking Green slowly
Meaning
Add Responder Setup Mode, or
LED on/off Setup Mode
Blinking Red slowly
Double-Blinking Green slowly
Double-Blinking Red slowly
Remove Responder Setup Mode
Multi-Add Responder Setup Mode, or
Beeper on/off Setup Mode
Multi-Remove Responder Setup Mode, or
Keypad Configuration Setup Mode
Factory Reset
The factory reset procedure clears all settings from Mini Remote including INSTEON scenes.
1) If possible, unlink (remove) all scene responders prior to performing factory reset
2) Turn Mini Remote off (slide power switch to left)
3) Press & Hold Set Button
4) While continuing to hold the Set Button, turn Mini Remote back on (slide power switch to the right)
Mini Remote will beep and its LED stays solid green
Mini Remote will emit a long beep
Page 11 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
5) Continue to Hold Set Button until the long beep stops
LED turns solid red
6) Release Set Button
Mini Remote will double-beep and its LED will turn off
Specifications
General
Product Name
Brand
Manufacturer Product Number
UPC
FCC ID
Patent Number
Warranty
INSTEON
Scenes
Scene Configurations
Maximum Scene Links
Scene Commands Supported
Software Configurable
X10 Support
Operation
LED Type
LED during Use
Mini Remote Wireless Switch (formerly RemoteLinc 2)
INSTEON
2342-242, 2444A3 (US)
2342-442 (EU)
2342-542 (AUS/NZ)
813922011616
813922012606
813922012972
SBP2444A
7,345,998 US, International Patents Pending
2 Years, Limited
1 (default), configurable to 2
1 On/Off (default), 2 Toggle or 2 Always On
400
On
Begin Brightening
Off
Begin Dimming
End Brightening End Dimming
Fast Off Fast On
Yes
None
Two-color: Green and Red
Green Flash Once
Red Flash Once
On (sent)
Bright
Fast-On
Off
Dim
Fast-Off
Page 12 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
LED
Setup Button
On/Off Switch
Beeper
Battery Charging LED
RF Range
RF Frequency
Retains all settings without power
Mechanical
Color
Plastic
Button Configurations
Dimensions
Weight (w/battery)
Button Style
Optional Hardware
Red Blink for ~3 Seconds Scene Acknowledge Missing
Always used for setup, default On during use
Yes
Yes
Yes, configurable
Yes, Embedded (shines red through case during charge)
50’ Line-of-Sight
915MHz (US)
869MHz (EU)
921MHz (AUS/NZ)
Yes, all saved in Non-volatile EEPROM
White
UV Stabilized ABS
1 Scene (standard), 2 Scene (optional button kit)
2.6" H x 1.3" W x 0.39" D
1 Oz.
Plastic Paddles over Contact Switches
Wall Mount
Tabletop Stand
Visor Clip
Indoors, 32°F to 104°F, up to 85% relative humidity Operating Environment
Electrical
Battery type
Battery life (between charges)
Battery Re-charging cycles
Recharging jack
Recharging time
Sends Low Battery Warning
3.7 VDC Lithium Polymer, Rechargeable, non-replaceable
> 3 months under standard usage
> 500 recharging cycles
Standard, Micro-USB, 5VDC
~1 hour
Yes
Troubleshooting
Problem
Mini Remote won’t add a scene responder
Possible Cause
Mini Remote may be out of range of nearest dual-band INSTEON device
(hopper)
The INSTEON signal may not be getting to the “vicinity” of responder
Solution
Try moving an access point or other dual-band plug-in module closer to Mini Remote
Make sure phases are bridged, add additional
INSTEON devices and/or move around existing
INSTEON devices
Page 13 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
Problem Possible Cause Solution
Large appliances, such as refrigerators or air conditioners, may be producing electrical noise on the power line
Other electrical devices, such as computers, televisions, or power strips, may be absorbing the INSTEON signal
Install a power line noise filter (e.g. #1626-10) to filter electrical noise and minimize signal attenuation
Mini Remote will not turn a
Responder On (it may turn it off)
Ramp Rate may be Extremely Slow
Or
Responder may be Linked at OFF
Re-link to responder with fast Ramp Rate
Responder’s Load doesn’t appear to turn on right away
The Ramp Rate may be set too slow. Re-link to responder with fast Ramp Rate
Responder(s) is taking a long time to respond to a
Mini Remote
Mini Remote blinks red after I turn a scene On or
Off
Mini Remote will not respond
Mini Remote may be sending commands to a responder(s) that is no longer in use
Remove all unused Responders from the Mini
Remote. HINT: If you are using home automation software, you can easily check scene membership and eliminate unnecessary Links
If the above doesn’t work, try the solutions for “Mini
Remote will not turn a Responder On”
One or more scene members not responding
Or
One or more scene members not responding AND HouseLinc (or other software) is attempting to communicate to Mini Remote
Monitor for recurrence and if recurs: a) Remove all scene responders that are no longer in use, or b) Add INSTEON devices for better signaling
Power cycle: Turn unit Off (slide switch to left), wait
10 seconds and turn back on
Something may have caused the Mini
Remote to unexpectedly stop responding
Perform a factory reset on Mini Remote
If you have tried these solutions, reviewed this Owner’s Manual, and still cannot resolve an issue you are having, please call: 866-243-8022
Page 14 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
Certification and Warranty
FCC & Industry Canada Compliance Statement
This device complies with FCC Rules Part 15 and Industry Canada RSS-210 (Rev. 7). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.
The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures:
- Re-orient or relocate the receiving antenna of the device experiencing the interference
- Increase the distance between this device and the receiver
- Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver
- Consult the dealer or an experienced radio/TV technician
WARNING: Changes or modifications to this device not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
DECLARATION OF CONFORMITY
Hereby, INSTEON declares that this device is in compliance with the essential requirements and other relevant provisions of the following Directives:
1) Electromagnetic Compatibility Directive 2004/108/EC
2) Hazardous Substance Directive 2005/95/EC
Technical data and copies of the original Declaration of Conformity are available and can be obtained from INSTEON; 16542 Millikan Ave, Irvine, CA,
USA.
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE)
This document contains important information for users with regards to the proper disposal and recycling of INSTEON products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:
Environmental Information for Customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health.
For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.
DECLARATION OF CONFORMITY TO R&TTE DIRECTIVE 1999/5/EC for the European Community, Switzerland, Norway, Iceland and
Liechtenstein
Product category: general consumer (category 3).
English: This equipment is in compliance with the essential requirements and other relevant provisions of the European R&TTE Directive 1999/5/EC
Deutsch [German]: Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.
Nederlands [Dutch]: Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC.
Svenska [Swedish]: Denna utrustning står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Français [French]: Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC
Page 15 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
Español [Spanish]: Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE.
Português [Portuguese]: Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.
Italiano [Italian]: Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE.
Norsk [Norwegian]: Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF.
Suomi [Finnish]:Tämä laite tÿttää direktiivin 1999/5/EY olennaiset vaatimukset ja on siinä asetettujen muiden laitetta koskevien määräysten mukainen.
Dansk [Danish]: Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF.
Polski [Polish]: Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami okreslonymi Dyrektywą UE: 1999/5/EC
Limited Warranty
Seller warrants to the original consumer purchaser of this product that, for a period of one year from the date of purchase, this product will be free from defects in material and workmanship and will perform in substantial conformity to the description of the product in this Owner’s Manual. This warranty shall not apply to defects or errors caused by misuse or neglect. If the product is found to be defective in material or workmanship, or if the product does not perform as warranted above during the warranty period, Seller will either repair it, replace it, or refund the purchase price, at its option, upon receipt of the product at the address below, postage prepaid, with proof of the date of purchase and an explanation of the defect or error. The repair, replacement, or refund that is provided for above shall be the full extent of Seller’s liability with respect to this product. For repair or replacement during the warranty period, call the INSTEON Gold Support Line at 866-243-8022 with the Model # and Revision # of the device to receive an RMA# and send the product, along with all other required materials to:
INSTEON
ATTN: Receiving
16542 Millikan Ave.
Irvine, CA 92606-5027
Limitations
The above warranty is in lieu of and Seller disclaims all other warranties, whether oral or written, express or implied, including any warranty or merchantability or fitness for a particular purpose. Any implied warranty, including any warranty of merchantability or fitness for a particular purpose, which may not be disclaimed or supplanted as provided above shall be limited to the one-year of the express warranty above. No other representation or claim of any nature by any person shall be binding upon Seller or modify the terms of the above warranty and disclaimer.
Home automation devices have the risk of failure to operate, incorrect operation, or electrical or mechanical tampering. For optimal use, manually verify the device state. Any home automation device should be viewed as a convenience, but not as a sole method for controlling your home.
In no event shall Seller be liable for special, incidental, consequential, or other damages resulting from possession or use of this device, including without limitation damage to property and, to the extent permitted by law, personal injury, even if Seller knew or should have known of the possibility of such damages. Some states do not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation of damages, in which case the above limitations and/or exclusions may not apply to you. You may also have other legal rights that may vary from state to state.
Protected under U.S. and foreign patents (see www.insteon.com/patents )
© Copyright 2013 INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 866-243-8022, www.insteon.com
Page 16 of 16 2342-242/2444A3, 2342-442, 2342-542 Rev: 1/21/2014 7:24 AM
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement